溅射功率对ZnO：Si透明导电薄膜性能的影响

采用直流磁控溅射法在室温玻璃基片上制备出了掺硅氧化锌（ZnO：Si）透明导电薄膜,研究了溅射功率对ZnO：Si薄膜结构、形貌、光学及电学性能的影响,实验结果表明,溅射功率对ZnO：Si薄膜的生长速率、结晶质量及电学性能有很大影响,而对其光学性能影响不大。实验制备的ZnO：LSi薄膜为六方纤锌矿结构的多晶薄膜,且具有垂直于基片方向的c轴择优取向。当溅射功率从45W增加到105W时,薄膜的晶化程度提高、晶粒尺寸增大,薄膜的电阻率减小;当溅射功率为105W时,薄膜的电阻率达到最小值3．83~104n·cm,其可见光透过率为94．41％。实验制备的ZnO：Si薄膜可以用作薄膜太阳能电池和液晶显示器的透明电极。     

直流磁控溅射法低温制备GZO:Ti薄膜及其光电性能研究

用直流磁控溅射法在玻璃衬底上成功制备出了钛镓共掺杂氧化锌(GZO:Ti)透明导电薄膜,研究了溅射压强和功率对GZO:Ti薄膜的微观结构和光电性能的影响。研究结果表明,所制备的GZO:Ti薄膜为六角纤锌矿结构的多晶薄膜,且具有c轴择优取向。溅射压强和功率对薄膜的电阻率和微观结构均有显著影响。随功率增大,薄膜电阻率降低,生长率增大。所制备的薄膜的最小电阻率为1.81×10-4Ω·cm,可见光区平均透过率大于84%。     

利用脉冲直流磁控溅射制备ZnO:Al薄膜的研究

利用中频脉冲直流磁控溅射法制备了平面ZnO:Al(AZO)透明导电薄膜,研究了沉积压力、衬底温度和溅射功率对AZO薄膜光电性能、薄膜稳定性的影响.结果表明:在较低沉积压力、衬底温度及溅射功率下,可获得具有低电阻率、高透过率、高稳定性的AZO薄膜.     

ZnO∶Nb透明导电薄膜的制备及光电特性研究

采用直流磁控溅射法在玻璃衬底上沉积铌掺杂氧化锌(NZO)透明导电薄膜。通过X射线衍射(XRD)、扫描电镜(SEM)以及透射光谱等测试研究了溅射功率对薄膜结构、形貌以及光电性能的影响。实验结果表明NZO薄膜是多晶膜,具有ZnO的六角纤锌矿结构,最佳取向为(002)方向。溅射功率从40W增加到80W时,薄膜的电阻率迅速下降;功率超过80W时,电阻率趋于平稳。在溅射功率为100W时,电阻率具有最小值5.89×10-4Ω.cm,光学带隙具有最大值3.395eV。实验制备的NZO薄膜附着性能良好,在可见光范围内的平均透过率均超过86.6%。     

溅射功率对镓掺杂氧化锌薄膜光电性能的影响

本文利用射频磁控溅射的方法首次制备了厚度小于200 nm的低电阻率高透过率的镓掺杂ZnO(GZO)薄膜.研究了溅射功率的改变对GZO薄膜光电性能的影响.利用扫描电镜对薄膜的微观结构进行了观察,利用四探针测试仪、紫外-可见分光光度计对GZO薄膜的光电性能进行了测试.实验结果表明:薄膜电阻率随溅射功率增大而迅速下降,从46...     

溅射功率对Mo掺杂ZnO(MZO)透明导电薄膜的影响

Mo原子具有较高的价态(+6),每个掺杂的Mo原子可以向ZnO晶体贡献4个自由电子,因此,Mo原子被认为是提高ZnO薄膜导电性的潜在掺杂剂.采用射频磁控溅射制备不同溅射功率下的MZO透明导电薄膜,研究溅射功率对MZ O薄膜表面形貌、微观结构、组织以及光电性能的影响.实验结果表明,不同功率制备的MZO薄膜样品都沿(002...     

溅射功率对ZnO:Al薄膜光电性能的影响

采用射频磁控溅射工艺,以Al掺杂ZnO(ZAO)陶瓷靶为靶材在石英玻璃基片上制备出具有优良光电性能的ZAO透明导电薄膜,研究了溅射功率对薄膜光电性能的影响。在不同溅射功率条件下制备的ZAO薄膜具有很好的c轴择优取向。较大功率溅射有利于薄膜晶粒尺寸的增大、电阻率降低。ZAO薄膜在可见光区的透过率平均值高达90%以上,受溅射功率影响不大。在340nm-420nm波长附近ZAO薄膜透过率急剧下降,呈现明显的紫外吸收边;高的溅射功率提高了ZAO薄膜的光学带隙宽度。     

室温下射频磁控溅射制备ZnO∶Al透明导电薄膜及其性能研究

采用射频磁控溅射技术,在室温下,以ZnO∶Al203(2％Al2O3(质量比))为靶材,在石英玻璃基底上,采用不同工艺条件制备了ZnO∶Al(AzO)薄膜.使用扫描电子显微镜观察了薄膜的表面形貌,X射线衍射分析了薄膜的结构,四探针测量仪得到薄膜的表面电阻,轮廓仪测量了薄膜厚度,并计算了电阻率,最后采用分光光度计测量了薄膜的透过率;研究了溅射功率、溅射气压与薄膜厚度对薄膜电阻率及透过率的影响.结果表明:所制备的AZO薄膜具有(002)择优取向,并且发现薄膜厚度对薄膜的光电性能有明显影响,溅射气压和溅射功率对薄膜电学性能有较大影响,但是对薄膜透过率影响不大.当功率为1kW、溅射气压0.052 Pa、AZO薄膜厚度为250nm时,其电阻率为8.38×10-4Ω·cm,波长在550 nm处透过率为89％,接近基底的本底透过率92％.当薄膜厚度为1125 nm时薄膜的电阻率降至最低(6.16×10-4 Ω·cm).     

铝锆共掺杂氧化锌透明导电薄膜的低温制备及特性研究

利用直流磁控溅射法在室温玻璃衬底上制备出了可见光透过率高、电阻率低的铝锆共掺杂氧化锌(ZAZO)透明导电薄膜。讨论了溅射功率对ZAZO薄膜结构、形貌和光电性能的影响。实验结果表明,溅射功率对ZAZO薄膜的结构、形貌和电学性能有很大影响,而对其光学性能影响不大。扫描电子显微镜和X射线衍射仪研究结果表明,ZAZO薄膜为六方纤锌矿结构的多晶薄膜,具有垂直于衬底方向的c轴择优取向。当溅射功率为120 W时,薄膜的电阻率达到最小值5.28×10-4Ω.cm,其可见光区平均透过率超过94%。     

氧化锌掺钇透明导电薄膜的制备及光电特性研究

采用射频磁控溅射法,室温下在玻璃衬底上制备出了具有良好附着性、低电阻率和高透过率的新型透明导电薄膜YZO(ZnO掺杂Y2O3简称YZO)。在薄膜厚度为600nm的情况下,研究了薄膜电学特性随溅射功率和溅射气压的变化情况。X射线衍射谱表明YZO薄膜是多晶膜,具有ZnO的六角纤锌矿结构,最佳取向为(002)方向。最佳溅射条件下制备的薄膜电阻率为8.71×10-4Ω.cm,在可见光范围内平均透过率达到92.3%,禁带宽度为3.57eV。     

Low-temperature deposited Titanium-doped zinc oxide thin films on the flexible PET substrate by DC magnetron sputtering

Transparent conducting Titanium-doped zinc oxide thin films (TZO) with high transparency and relatively low resistivity were firstly deposited on water-cooled polyethylene terephthalate (PET) substrates at room temperature by DC magnetron sputtering. The microstructure, optical and electrical properties of the deposited films were investigated and discussed. The XRD patterns show that all the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. The electrical resistivity decreases when the sputtering power increases from 45 W to 60 W. However, as the puttering power continue increases from 60 W to 90 W, the electrical resistivity increases rapidly. When the puttering power is 60 W, the films deposited on PET substrate have the lowest resistivity of 4.72 × 10⁻⁴ Ω cm and a relatively high transmittance of above 92% in the visible range.     

Mn-doped ZnO transparent conducting films deposited by DC magnetron sputtering

Mn-doped zinc oxide (ZnO:Mn) thin films with low resistivity and relatively high transparency were firstly prepared on glass substrate by direct current (DC) magnetron sputtering at room temperature. Influence of film thickness on the properties of ZnO:Mn films was investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) show that all the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. As the thickness increases from 144 to 479 nm, the crystallite size increases while the electrical resistivity decreases. However, as the thickness increases from 479 to 783 nm, the crystallite size decreases and the electrical resistivity increases. When film thickness is 479 nm, the deposited films have the lowest resistivity of 2.1 × 10^− 4 Ω cm and a relatively high transmittance of above 84% in the visible range.     

Influence of annealing temperature on the properties of ZnO:Zr films deposited by direct current magnetron sputtering

Transparent conducting zirconium-doped zinc oxide (ZnO:Zr) films were deposited on quartz substrates by direct current (DC) magnetron sputtering at room temperature. The influence of post-annealing temperature on the structural, morphological, electrical and optical properties of ZnO:Zr films were investigated. When annealing temperature increases from room temperature to 573 K, the resistivity decreases obviously due to an improvement of the crystallinity. However, with further increase in annealing temperature, the crystallinity deteriorates leading to an increase in resistivity. The films annealed at the optimum annealing temperature of 573 K in vacuum have the lowest resistivity of 9.8 × 10⁻⁴ Ω cm and a high transmittance of above 92% in the visible range.     

Study on the doping effect of Li-doped ZnO film

Zinc oxide (ZnO) is an excellent piezoelectric material with simple composition. ZnO film is applied to the piezoelectric devices because it has high resistivity and highly oriented direction at c-axis. Structural and electrical properties in ZnO films are influenced by deposition conditions. Lithium-doped ZnO (LZO) films were deposited by RF magnetron sputtering method using Li-doped ZnO ceramic target with various ratios (0 to 10 wt.% LiCl dopant). LZO films revealed high resistivity of above 10⁷ Ω cm with smooth surface when they were deposited with 4% LiCl-doped ZnO target under room temperature. However, their c-axis orientation was worse than the c-axis orientation of pure ZnO films. We have also studied on structural, optical and electrical properties of the ZnO films by XRD, AFM, SEM, XPS, and 4-point probe analyses. We concluded that LZO films were deposited with 4 wt.% LiCl-doped ZnO target and were apposite for piezoelectrical application.     

Ar Pressure Dependence of the Properties of Molybdenum-doped ZnO Films Grown by RF Magnetron Sputtering

Transparent conducting oxide film of molybdenum-doped zinc oxide （MZO） with high transparency and relatively low resistivity was prepared by RF （radio frequency） magnetron sputtering at room temperature. The structural, electrical, and optical properties of the films deposited under different Ar pressure were investigated.XRD （X-ray diffraction） patterns show that the nature of the films is polycrystalline with a hexagonal structure and a preferred orientation along the c-axis. The resistivity increases as Ar pressure increases. The lowest range exceeds 88% for all the samples. The optical band gap decreases from 3.27 to 3.15 eV with increasing Ar pressure from 0.6 to 3.0 Pa.     

薄膜厚度对TGZO透明导电薄膜光电性能的影响

利用直流磁控溅射法,在室温水冷玻璃衬底上成功制备出了可见光透过率高、电阻率低的钛镓共掺杂氧化锌(TG-ZO)透明导电薄膜。X射线衍射和扫描电子显微镜研究结果表明,TGZO薄膜为六角纤锌矿结构的多晶薄膜,且具有c轴择优取向。研究了厚度对TGZO透明导电薄膜电学和光学性能的影响,结果表明厚度对薄膜的光电性能有重要影响。当薄膜厚度为628 nm时,薄膜具有最小电阻率2.01×10-4Ω.cm。所制备薄膜在波长为400~760 nm的可见光中平均透过率都超过了91%,TGZO薄膜可以用作薄膜太阳能电池和液晶显示器的透明电极。     

Low-temperature deposited Titanium-doped zinc oxide thin films on the flexible PET substrate by DC magnetron sputtering

Transparent conducting Titanium-doped zinc oxide thin films (TZO) with high transparency and relatively low resistivity were firstly deposited on water-cooled polyethylene terephthalate (PET) substrates at room temperature by DC magnetron sputtering. The microstructure, optical and electrical properties of the deposited films were investigated and discussed. The XRD patterns show that all the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. The electrical resistivity decreases when the sputtering power increases from 45 W to 60 W. However, as the puttering power continue increases from 60 W to 90 W, the electrical resistivity increases rapidly. When the puttering power is 60 W, the films deposited on PET substrate have the lowest resistivity of 4.72 × 10⁻⁴ Ω cm and a relatively high transmittance of above 92% in the visible range.     

氢化及沉积温度对掺铝ZnO透明导电薄膜性能影响

采用射频磁控溅射方法在玻璃衬底上制备了掺铝ZnO透明导电薄膜(AZO)。为了降低AZO薄膜的电阻率, 采用在溅射气氛中通入一定比例H₂的方法对AZO薄膜进行氢化处理, 并研究了溅射气氛中H₂含量及衬底温度对AZO薄膜氢化效果的影响。结果表明: 在低温条件下, 氢化处理能有效降低AZO薄膜的电阻率; 在衬底温度为100℃的低温条件下, 通过调节溅射气氛中H₂的比例, 制备了电阻率为6.0×10^-4 Ω·cm的高质量氢化AZO薄膜, 该电阻值低于同等条件下未氢化AZO薄膜电阻值的1/3; 但随着衬底温度的升高, 氢化处理对薄膜电学性能的改善效果逐渐减弱。     

室温下射频磁控溅射制备ZnO:Al透明导电薄膜及其性能研究

采用射频磁控溅射技术,在室温下,以ZnO:Al2O3(2%Al2O3(质量比))为靶材,在石英玻璃基底上,采用不同工艺条件制备了ZnO:Al(AZO)薄膜。使用扫描电子显微镜观察了薄膜的表面形貌,X射线衍射分析了薄膜的结构,四探针测量仪得到薄膜的表面电阻,轮廓仪测量了薄膜厚度,并计算了电阻率,最后采用分光光度计测量了薄膜的透过率;研究了溅射功率、溅射气压与薄膜厚度对薄膜电阻率及透过率的影响。结果表明:所制备的AZO薄膜具有(002)择优取向,并且发现薄膜厚度对薄膜的光电性能有明显影响,溅射气压和溅射功率对薄膜电学性能有较大影响,但是对薄膜透过率影响不大。当功率为1kW、溅射气压0.052Pa、AZO薄膜厚度为250nm时,其电阻率为8.38×10-4Ω·cm,波长在550nm处透过率为89%,接近基底的本底透过率92%。当薄膜厚度为1125 nm时薄膜的电阻率降至最低(6.16×10-4Ω·cm)。