Liquid water breakthrough pressure through gas diffusion layer of proton exchange membrane fuel cell

The dynamic behavior of liquid water transport through the gas diffusion layer (GDL) of the proton exchange membrane fuel cell is studied with an ex-situ approach. The liquid water breakthrough pressure is measured in the region between the capillary fingering and the stable displacement on the drainage phase diagram. The variables studied are GDL thickness, PTFE/Nafion content within the GDL, GDL compression, the inclusion of a micro-porous layer (MPL), and different water flow rates through the GDL. The liquid water breakthrough pressure is observed to increase with GDL thickness, GDL compression, and inclusion of the MPL. Furthermore, it has been observed that applying some amount of PTFE to an untreated GDL increases the breakthrough pressure but increasing the amount of PTFE content within the GDL shows minimal impact on the breakthrough pressure. For instance, the mean breakthrough pressures that have been measured for TGP-060 and for untreated (0 wt.% PTFE), 10 wt.% PTFE, and 27 wt.% PTFE were 3589 Pa, 5108 Pa, and 5284 Pa, respectively.     

Passive water management at the cathode of a planar air-breathing proton exchange membrane fuel cell

Water management is a significant challenge in portable polymer electrolyte membrane (PEM) fuel cells and particularly in proton exchange membrane (PEM) fuel cells with air-breathing cathodes. Liquid water condensation and accumulation at the cathode surface is unavoidable in a passive design operated over a wide range of ambient and load conditions. Excessive flooding or dry out of the open cathode can lead to a dramatic reduction of fuel cell power. We report a water management design based on a hydrophilic and electrically conductive wick. A prototype air-breathing fuel cell with the proposed water management design successfully operated under severe flooding conditions, ambient temperature 10 °C and relative humidity of 80%, for up to 6 h with no observable cathode flooding or loss of performance.     

Measurement of the water transport rate in a proton exchange membrane fuel cell and the influence of the gas diffusion layer

Water management in a PEM fuel cell significantly affects the fuel cell performance and durability. The gas diffusion layer (GDL) of a PEM fuel cell plays a critical role in the water management process. In this short communication, we report a simple method to measure the water transport rate across the GDL. Water rejection rates across a GDL at different cathode air-flow rates were measured. Based on the measurement results, the fuel cell operating conditions, such as current density, temperature, air stoichiometry and relative humidity, corresponding to membrane drying and flooding conditions were identified for the particular GDL used. This method can help researchers develop GDLs for a particular fuel cell design with specific operating conditions and optimize the operation conditions for the given PEM fuel cell components.     

Measurement of water transport rates across the gas diffusion layer in a proton exchange membrane fuel cell,and the influence of polytetrafluoroethylene content and micro-porous layer

Water management in a proton exchange membrane (PEM) fuel cell is one of the critical issues for improving fuel cell performance and durability, and water transport across the gas diffusion layer plays a key role in PEM fuel cell water management. In this work, we investigated the effects of polytetrafluoroethylene (PTFE) content and the application of a micro-porous layer (MPL) in the gas diffusion layer (GDL) on the water transport rate across the GDL. The results show that both PTFE and the MPL play a similar role of restraining water transport. The effects of different carbon loadings in the MPL on water transport were also investigated. The results demonstrate that the higher the carbon loading in the MPL, the more it reduces the water transport rate. Using the given cell hardware and components, the optimized operation conditions can be obtained based on a water balance analysis.     

A review of water flooding issues in the proton exchange membrane fuel cell

We have reviewed more than 100 references that are related to water management in proton exchange membrane (PEM) fuel cells, with a particular focus on the issue of water flooding, its diagnosis and mitigation. It was found that extensive work has been carried out on the issues of flooding during the last two decades, including prediction through numerical modeling, detection by experimental measurements, and mitigation through the design of cell components and manipulating the operating conditions. Two classes of strategies to mitigate flooding have been developed. The first is based on system design and engineering, which is often accompanied by significant parasitic power loss. The second class is based on membrane electrode assembly (MEA) design and engineering, and involves modifying the material and structural properties of the gas diffusion layer (GDL), cathode catalyst layer (CCL) and membrane to function in the presence of liquid water. In this review, several insightful directions are also suggested for future investigation.     

Effect of wettability on water removal from the gas diffusion layer surface in a novel proton exchange membrane fuel cell flow channel

Effective water removal from the proton exchange membrane fuel cell (PEMFC) surface exposed to the flow channel is critical to the operation and water management in PEMFCs. In this study, the water removal process is investigated numerically for a novel flow channel formed by inserting a hydrophilic needle in the conventional PEMFC flow channel, and the effect of the surface wettability of the membrane electrode assembly (MEA) and the inserted needle on the water removal process is studied. The results show that the liquid water can be more effectively removed from the MEA surface for larger MEA surface contact angles and smaller needle surface contact angles. The pressure drop for the flow in the channel is also examined and it is seen to be indicative of the liquid water flow and transport in the flow channel, suggesting that pressure drop is a useful parameter for the investigation of water transport and dynamics in the flow channel.     

Visualization of unstable water flow in a fuel cell gas diffusion layer

Modeling two-phase flow in proton exchange membrane (PEM) fuel cells is hampered by a lack of conceptual understanding of flow patterns in the gas diffusion layer (GDL). In this paper, pore-scale visualizations of water in different types of GDLs were used to improve current understanding of flow and transport phenomena in PEM fuel cells. Confocal microscopy was used to capture the real-time transport of water, and pressure micro-transducers were installed to measure water breakthrough pressures. Three types of fuel cell GDLs were examined: TO series (Toray Corp., Tokyo, Japan), SGL series (SGL Carbon Group, Wiesbaden, Germany), and MRC series (Mitsubishi Rayon Corp., Otake City, Japan). The visualizations and pressure measurements revealed that despite difference in “pore” structures in the three types of GDLs, water followed distinct flow paths spanning several pores with characteristics similar to the “column flow” phenomena observed previously in hydrophobic or coarse-grained hydrophilic soils. The results obtained from this study can aid in the construction of theories and models for optimizing water management in fuel cells.     

Effect of water distribution in gas diffusion layer on proton exchange membrane fuel cell performance

Water management of proton exchange membrane fuel cells remains a prominent issue in research concerning fuel cells. In this study, the gas diffusion layer (GDL) of a fuel cell is partially treated with a hydrophobic agent, and the effect of GDL hydrophobicity on the water distribution in the fuel cell is examined. First, the effect of the position of the cathode GDL hydrophobic area relative to the channel on the fuel cell performance is investigated. Then, the water distribution in the fuel cell cathode GDL is observed using X-ray imaging. The experimental results indicate that when the hybrid GDL's hydrophobic area lies on the channel, water tends to accumulate under the rib, and the water content in the channel is low; this improves the fuel cell performance. When the hydrophobic area is under the rib, the water distribution is more uniform, but the performance deteriorates.     

Liquid water flooding process in proton exchange membrane fuel cell cathode with straight parallel channels and porous layer

Liquid water management plays a significant role in proton exchange membrane fuel cell (PEMFC) performance, especially when the PEMFC is operating with high current density. Therefore, understanding of liquid water behavior and flooding process is a critical challenge that must be addressed. To overcome PEMFC durability problems, a liquid water flooding process is studied in the cathode side of a PEMFC with straight parallel channels and a porous layer using FLUENT^® v6.3.26 software with a volume-of-fluid (VOF) algorithm and user-defined-function (UDF). The general process of liquid water flooding within this type of PEMFC cathode is investigated by analyzing the behavior of liquid water in porous layer and gas flow channels. Two important phenomena, the “first channel phenomenon” and the “last channel phenomenon”, and their effects on the flow distribution along different parallel channels are discussed.     

Influence of the gas diffusion cathode structure on the performance of an air-breathing proton exchange membrane fuel cell

This study presents a comprehensive analysis regarding the relevance of the cathode electrode structure on the performance of an air-breathing proton exchange membrane fuel cell, for which water management is a critical issue. In the light of the obtained results, general guidelines for designing a high-performance cathode for air-breathing operation are provided. Selecting adequate characteristics for the gas diffusion electrode in the cathode is shown to be crucial for optimizing performance. Sufficiently thin catalytic layers increase impressively Pt utilization by favouring the access of oxygen and protons to the electroactive centres. The properties of the gas diffusion medium for air-breathing cathodes have been also observed to be critical. The study reveals that selection criteria for gas diffusion layers based on high air permeability and good hydrophobicity does not ensure optimal performance. The ability of the GDL macroporous structure to expel water from the cathode is decisive for improving oxygen access to the catalytic layer and obtaining high-performance air-breathing fuel cells.     

Analysis of the water and thermal management in proton exchange membrane fuel cell systems

Water and thermal management is essential to the performance of proton exchange membrane (PEM) fuel cell system. The key components in water and thermal management system, namely the fuel cell stack, radiator, condenser and membrane humidifier are all modeled analytically in this paper. Combined with a steady-state, one-dimensional, isothermal fuel cell model, a simple channel-groove pressure drop model is included in the stack analysis. Two compact heat exchangers, radiator and condenser are sized and rated to maintain the heat and material balance. The influence of non-condensable gas is also considered in the calculation of the condenser. Based on the proposed methodology, the effects of two important operating parameters, namely the air stoichiometric ratio and the cathode outlet pressure, and three kinds of anode humidification, namely recycling humidification, membrane humidification and recycling combining membrane humidification are analyzed. The methodology in this article is helpful to the design of water and thermal management system in fuel cell systems.     

Innovative gas diffusion layers and their water removal characteristics in PEM fuel cell cathode

Liquid water transport is one of the key challenges regarding the water management in a proton exchange membrane (PEM) fuel cell. Conventional gas diffusion layers (GDLs) do not allow a well-organized liquid water flow from catalyst layer to gas flow channels. In this paper, three innovative GDLs with different micro-flow channels were proposed to solve liquid water flooding problems that conventional GDLs have. This paper also presents numerical investigations of air–water flow across the proposed innovative GDLs together with a serpentine gas flow channel on PEM fuel cell cathode by use of a commercial computational fluid dynamics (CFD) software package FLUENT. The results showed that different designs of GDLs will affect the liquid water flow patterns significantly, thus influencing the performance of PEM fuel cells. The detailed flow patterns of liquid water were shown. Several gas flow problems for the proposed different kinds of innovative GDLs were observed, and some useful suggestions were given through investigating the flow patterns inside the proposed GDLs.     

Effect of hydrophilic pipe structure of proton exchange membrane fuel cell on water removal from the gas diffusion layer surface

In a proton exchange membrane fuel cell (PEMFC), effective GDL surface water elimination is significant to water management. This paper used the volume-of-fluid method (VOF) method to carry out simulation research on transferring liquid water in the flow channel with a hydrophilic pipe. The findings indicated that compared with a straight channel, a hydrophilic pipe structure could effectively remove water from the gas diffusion surface (GDL) and reduce the surface water coverage of the GDL. With the increase in the diameter and height of the pipe structure, the GDL surface's water coverage first increased and then decreased, and it was less with the pipe structure than with the direct flow channel. The removal rate of water on the GDL surface was accelerated. The spacing of hydrophilic pipes has a significant impact on the transportation of water. As the spacing increases, the removal rate of water on the GDL surface slowed. A hydrophilic pipe structure with a diameter of 75 μm, a height of 400 μm, and spacing of 300 μm has good water removal performance on the GDL surface. This research work proposes a new internal structure design of the flow channel, which has specific implications for removing water on the GDL surface.     

Hierarchy carbon paper for the gas diffusion layer of proton exchange membrane fuel cells

This communication described the fabrication of a hierarchy carbon paper, and its application to the gas diffusion layer (GDL) of proton exchange membrane (PEM) fuel cells. The carbon paper was fabricated by growing carbon nanotubes (CNTs) on carbon fibers via covalently assembling metal nanocatalysts. Surface morphology observation revealed a highly uniform distribution of hydrophobic materials within the carbon paper. The contact angle to water of this carbon paper was not only very large but also particularly even. Polarization measurements verified that the hierarchy carbon paper facilitated the self-humidifying of PEM fuel cells, which could be mainly attributed to its higher hydrophobic property as diagnosed by electrochemical impedance spectroscopy (EIS).     

Review of gas diffusion layer for proton exchange membrane-based technologies with a focus on unitised regenerative fuel cells

Proton exchange membrane (PEM) based technologies (fuel cells and electrolysers) offer promising sustainable power generation and storage solutions for a diverse range of stationary and mobile applications. Unitised regenerative fuel cell (URFC) is an electrochemical cell that can operate both as a fuel cell (FC) and an electrolyser (E). However, for a widespread commercialisation, further improvements are required that address the durability, performance, and cost limitations. One of the main challenging components in developing URFCs is the gas diffusion layer (GDL) as it plays different vital roles, some of which are paradoxical in FC and E-modes. Therefore, in this paper, the published research on GDL of PEM-URFCs as well as relevant studies on PEM fuel cells and electrolysers are critically reviewed. The materials and novel methods to address the corrosion in E-mode are discussed. This is followed by presenting and discussing different properties of GDLs affecting the performance in FC and E-modes: i.e. porosity, thickness, pore size, transport properties, thermal and electrical conductivity, and the GDL compressibility. Finally, the main modifications of the GDLs, such as hydrophobisation and microporous layer application, to improve the performance of a URFC are analysed and discussed.     

Experimental investigations on liquid water removal from the gas diffusion layer by reactant flow in a PEM fuel cell

The cross flow from channel to channel through gas diffusion layer (GDL) under the land could play an important role for water removal in proton exchange membrane (PEM) fuel cells. In this study, characteristics of liquid water removal from GDL have been investigated experimentally, through measuring unsteady pressure drop in a cell which has the GDL initially wet with liquid water. The thickness of GDL is carefully controlled by inserting various thicknesses of metal shims between the plates. It has been found that severe compression of GDL could result in excessive pressure drop from channel inlet to channel outlet. Removing liquid water from GDL by cross flow is difficult for GDL with high compression levels and for low inlet air flow rates. However, effective water removal can still be achieved at high compression levels of GDL if the inlet air flow rate is high. Based on different compressed GDL thicknesses, different GDL porosities and permeabilities were calculated and their effects on the characteristics of liquid water removal from GDL were evaluated. Visualization of liquid water transport has been conducted by using transparent flow channel, and liquid water removal from GDL under the land was observed for all the tested inlet air flow rates, which confirms that cross flow is practically effective to remove the liquid water accumulated in GDL under the land area.     

Water permeation through gas diffusion layers of proton exchange membrane fuel cells

Water transport through gas diffusion layer of proton exchange membrane fuels cells is investigated experimentally. A filtration cell is designed and the permeation threshold and the apparent water permeability of several carbon papers are investigated. Similar carbon paper with different thicknesses and different Teflon loadings are tested to study the effects of geometrical and surface properties on the water transport. Permeation threshold increases with both GDL thickness and Teflon loading. In addition, a hysteresis effect exists in GDLs and the permeation threshold reduces as the samples are retested. Moreover, several compressed GDLs are tested and the results show that compression does not affect the breakthrough pressure significantly. The measured values of apparent permeability indicate that the majority of pores in GDLs are not filled with water and the reactant access to the catalyst layer is not hindered.     

Effect of cathode gas diffusion layer on water transport and cell performance in direct methanol fuel cells

The optimal design of the cathode gas diffusion layer (GDL) for direct methanol fuel cells (DMFCs) is not only to attain better cell performance, but also to achieve better water management for the DMFC system. In this work, the effects of both the PTFE loading in the cathode backing layer (BL) as well as in the micro-porous layer (MPL) and the carbon loading in the MPL on both water transport and cell performance were investigated experimentally. The experimental data showed that with the presence of a hydrophobic MPL in the GDL, the water-crossover flux through the membrane decreased slightly with increasing the PTFE loading in the BL. However, a higher PTFE loading in the BL not only lowered cell performance, but also resulted in an unstable discharging process. It was also found that the PTFE loading in the MPL had little effect on the water-crossover flux, but its effect on cell performance was substantial: the 40-wt% PTFE loading in the MPL was found to be the optimal value to achieve the best performance. The experimental results further showed that increasing the carbon loading in the MPL significantly lowered the water-crossover flux, but a too high carbon loading would decrease the cell performance as the result of the increased oxygen transport resistance; the 2.0-mg C cm⁻² carbon loading was found to exhibit the best performance.     

In-plane gas permeability of proton exchange membrane fuel cell gas diffusion layers

A new analytical approach is proposed for evaluating the in-plane permeability of gas diffusion layers (GDLs) of proton exchange membrane fuel cells. In this approach, the microstructure of carbon papers is modeled as a combination of equally-sized, equally-spaced fibers parallel and perpendicular to the flow direction. The permeability of the carbon paper is then estimated by a blend of the permeability of the two groups. Several blending techniques are investigated to find an optimum blend through comparisons with experimental data for GDLs. The proposed model captures the trends of experimental data over the entire range of GDL porosity. In addition, a compact relationship is reported that predicts the in-plane permeability of GDL as a function of porosity and the fiber diameter. A blending technique is also successfully adopted to report a closed-form relationship for in-plane permeability of three-directional fibrous materials.     

Optimization of cathode microporous layer materials for proton exchange membrane fuel cell

The microporous layer (MPL) of diffusion medium has an important impact on the water management ability of proton exchange membrane fuel cells. In this study, six kinds of carbon black were used to prepare the cathode MPL. The thickness, conductivity, pore structure, hydrophobicity, and surface microstructure of MPL were characterized. The single cell was prepared and electrochemical tests were performed. The results showed that the single cell prepared by Acetylene black (ACET) and Vulcan XC-72R has a considerable power generation performance. In addition, polyvinylidene fluoride hexafluoropropylene copolymer P(VDF-HFP) was used to replace Polytetrafluoroethylene (PTFE) as hydrophobic binder. MPL with different P(VDF-HFP) contents were prepared, and the single cell performance was investigated. The results showed that all the single cells prepared by P(VDF-HFP) were worse than that of PTFE. This study provides an important reference for further improving the performance of fuel cells from the perspective of material optimization with MPL.