Carbon film coating on gas diffusion layer for proton exchange membrane fuel cells

This study discusses a novel process to increase the performance of proton exchange membrane fuel cells (PEMFC). In order to improve the electrical conductivity and reduce the surface indentation of the carbon fibers, we modified the carbon fibers with pitch-based carbon materials (mesophase pitch and coal tar pitch). Compared with the gas diffusion backing (GDB), GDB-A240 and GDB-MP have 32% and 33% higher current densities at 0.5 V, respectively. Self-made carbon paper with the addition of a micro-porous layer (MPL) (GDL-A240 and GDL-MP) show improved performance compared with GDB-A240 and GDB-MP. The current densities of GDL-A240 and GDL-MP at 0.5 V increased by 37% and 31% compared with GDL, respectively. This study combines these two effects (carbon film and MPL coating) to promote high current density in a PEMFC.     

Facilitating mass transport in gas diffusion layer of PEMFC by fabricating micro-porous layer with dry layer preparation

For a proton exchange membrane fuel cell (PEMFC), dry layer preparation was optimized and applied to fabricate a micro-porous layer (MPL) for a gas diffusion layer (GDL). The MPLs fabricated by dry layer preparation and the conventional wet layer preparation were compared by physical and electrochemical methods. The PEMFC using dry layer MPLs showed better performance than that using wet layer MPLs, especially when the cells were operated under conditions of high oxygen utilization rate and high humidification temperature of air. The mass transport properties of the GDLs with the dry layer MPLs were also better than with the wet layer MPLs, and were found to be related to the pore size distribution in GDLs. The differences in surface morphology and pore size distribution for the GDLs with the dry layer and wet layer MPLs were investigated and analyzed. The dry layer preparation for MPLs was found to be more beneficial for forming meso-pores (pore size in the range of 0.5–15 μm), which are important and advantageous for facilitating gas transport in the GDLs. Moreover, the GDLs with the dry layer MPLs exhibited better electronic conductivity and more stable hydrophobicity than those with the wet layer MPLs. The reproducibility of the dry layer preparation for MPLs was also satisfying.     

气体扩散层结构对PEMFC性能影响二维数值模拟

质子交换膜燃料电池在运行过程中反应物从流道传输至催化层时会经过气体扩散层,气体扩散层即 可用来传输反应气体,又用来排出反应物生成的水,所以探究气体扩散层的结构对参加反应的物质及生成物 传输的影响规律有助于了解其分布情况。通过数值模拟比较了穿孔型、树状型和不规则形状气体扩散层在不 同孔隙率下顺流流动时对电池性能的影响情况。计算结果表明,气体扩散层结构严重影响质子交换膜燃料电 池性能,三种不同形状的气体扩散层对应的电性能随孔隙率的变化规律各不相同,到达催化层表面氧气的含 量受扩散层结构影响比氢气大,气体扩散层结构对阴极侧生成物水含量的影响不可忽略。     

Development of a novel hydrophobic/hydrophilic double micro porous layer for use in a cathode gas diffusion layer in PEMFC

In this study, a gas diffusion layer (GDL) was modified to improve the water management ability of a proton exchange membrane fuel cell (PEMFC). We developed a novel hydrophobic/hydrophilic double micro porous layer (MPL) that was coated on a gas diffusion backing layer (GDBL). The water management properties, vapor and water permeability, of the GDL were measured and the performance of single cells was evaluated under two different humidification conditions, R.H. 100% and 50%. The modified GDL, which contained a hydrophilic MPL in the middle of the GDL and a hydrophobic MPL on the surface, performed better than the conventional GDL, which contained only a single hydrophobic MPL, regardless of humidity, where the performance of the single cell was significantly improved under the low humidification condition. The hydrophilic MPL, which was in the middle of the modified GDL, was shown to act as an internal humidifier due to its water absorption ability as assessed by measuring the vapor and water permeability of this layer.     

Liquid transport in gas diffusion layer of proton exchange membrane fuel cells: Effects of micro-porous layer cracks

Micro porous layer (MPL) is a carbon layer (～15 μm) that coated on the gas diffusion layer (GDL) to enhance the electrical conduction and membrane hydration of proton exchange membrane fuel cell (PEMFC). However, the liquid transport behavior from MPL to GDL and its impact on water management remain unclear. Thus, a three-dimensional volume of fluid (VOF) model is developed to investigate the effects of MPL crack properties on liquid water saturation, liquid pathway formation, and the two-phase mass transport mechanism in GDL. Firstly, a stochastic orientation method is used to reconstruct the fibrous structure of the GDL. After that, the liquid water saturation calculated from the numerical results agrees well with the experimental data. With considering the full morphology of the overlap between MPL and GDL, it's found that this overlap determines the preferred liquid emerging port of both MPL and GDL. Three crack design shapes in MPL are proposed on the base of the similarity crack formation processes of soil mud. In addition, the effects of crack shape, distance between cracks, and crack number on liquid water transport from MPL to GDL are investigated. It is found that the liquid water saturation of GDL increases with crack number and the distance between cracks, while presents little correlation to the crack shape. Hopefully, these results can help the development of PEMFC models without reconstructing full MPL morphology.     

Novel single-layer gas diffusion layer based on PTFE/carbon black composite for proton exchange membrane fuel cell

A series of poly(tetrafluoroethylene)/carbon black composite-based single-layer gas diffusion layers (PTFE/CB-GDLs) for proton exchange membrane fuel cell (PEMFC) was successfully prepared from carbon black and un-sintered PTFE, which included powder resin and colloidal dispersion, by a simple inexpensive method. The scanning electron micrographs of PTFE/CB-GDLs indicated that the PTFE resins were homogeneously dispersed in the carbon black matrix and showed a microporous layer (MPL)-like structure. The as-prepared PTFE/CB-GDLs exhibited good mechanical property, high gas permeability, and sufficient water repellency. The best current density obtained from the PEMFC with the single-layer PTFE/CB-GDL was 1.27 and 0.42 A cm⁻² for H₂/O₂ and H₂/air system, respectively.     

Effects of the carbon black properties in gas diffusion layer on the performance of proton exchange membrane fuel cells

The microporous layer (MPL) as a part of diffusion medium has an important impact on mass transfer of proton exchange membrane fuel cell (PEMFC). In this study, MPLs of gas diffusion layers (GDLs) are prepared with different carbon blacks, and the properties of carbon blacks and their effects as MPLs on cell performance are systematically investigated. The results show that the GDL prepared by Acetylene Black (ACET) exhibits the best performance with a maximum power density up to 2.05 W cm⁻². Moreover, it still maintains extremely high performance with increasing current density even at humidity condition of 100% relative humidity, which means its excellent water/gas transportation capacity. This study contributes to deeply understanding the correlations between the properties of MPL material itself and their corresponding performance exhibited in cell. It also provides an important reference for enhancing cell performance and further advancing the practical applications of MPLs in PEMFC field.     

An analytical model for the transverse permeability of gas diffusion layer with electrical double layer effects in proton exchange membrane fuel cells

An analytical model is presented for the transverse permeability of gas diffusion layer (GDL) based on an ordered array of parallel charged circular cylinders at the steady state. The formula of calculating the permeability of the transverse direction is given by solving the fluid momentum equation in a unit cell. In the present approach, the proposed model is explicitly related to the porosity and fiber radius of fibrous porous media, the zeta potential, and the physical properties of the electrolyte solution. Besides, the effects of these parameters (the porosity, unit cell aspect ratio, fiber radius, and molar concentration) on the transverse permeability are discussed detailedly. The model predictions are compared with the previous studies in the available literature, and good agreement is found.     

Enhancement of proton exchange membrane fuel cell performance by titanium-coated anode gas diffusion layer

Titanium was coated onto an anode gas diffusion layer (GDL) by direct current sputtering to improve the performance and durability of a proton exchange membrane fuel cell (PEMFC). Scanning electron microscopy (SEM) images showed that the GDLs were thoroughly coated with titanium, which showed angular protrusion. Single-cell performance of the PEMFCs with titanium-coated GDLs as anodes was investigated at operating temperatures of 25 °C, 45 °C, and 65 °C. Cell performances of all membrane electrode assemblies (MEAs) with titanium-coated GDLs were superior to that of the MEA without titanium coating. The MEA with titanium-coated GDL, with 10 min sputtering time, demonstrated the best performance at 25 °C, 45 °C, and 65 °C with corresponding power densities 58.26%, 32.10%, and 37.45% higher than that of MEA without titanium coating.     

A review of gas diffusion layer in PEM fuel cells: Materials and designs

The gas diffusion layer (GDL) plays a key role on reactant gas diffusion and water management in proton exchange membrane (PEM) fuel cells. This paper reviews recent developments of single- and dual-layer GDLs for PEM fuel cells and various materials and approaches used for development of novel GDL. A variety of carbon- and metal-based macroporous substrates are presented. Hydrophobic treatments using different fluorinated polymers are addressed. Engineering parameters which control the performance of microporous layer such as carbon treatment, wettability, thickness, and microstructure are also reviewed. In addition, future prospects for development of new GDL development are discussed.     

Fractal model for predicting the effective binary oxygen diffusivity of the gas diffusion layer in proton exchange membrane fuel cells

We propose an analytical model to predict the effective binary oxygen diffusivity of the porous gas diffusion layer (GDL) in proton exchange membrane fuel cells (PEMFCs). In this study, we consider the fractal characteristics of the porous GDL as well as its general microstructure, and we adopt the Bosanquet equation to derive effective diffusivity. The fractal characterization of GDL enables us to model effective diffusivity in a continuous manner while taking into account the effect of pore size distribution. Comparison to two other theoretical models that are generally accepted in the simulation of PEMFCs shows similar trends in all three models, indicating that our proposed model is well founded. Furthermore, the predicted effective binary oxygen diffusivities of two samples show that after treatment with polytetrafluoroethylene (PTFE), the effective binary diffusivity of the GDL decreases. Based on the parametric effect analysis, we conclude that effective binary diffusivity is negatively correlated with tortuosity fractal dimension but positively correlated with the fractal dimension of pore area, porosity, or mean pore diameter. The proposed model facilitates fast prediction of effective diffusivity as well as multi-scale modeling of PEMFCs and thus facilitates the design of the GDLs and of PEMFCs.     

Preparation of microporous layer for proton exchange membrane fuel cell by using polyvinylpyrrolidone aqueous solution

A new method of preparing microporous layer (MPL) for proton exchange membrane fuel cell (PEMFC) was presented in this paper. Considering the bad dispersion of PTFE aqueous suspension in the carbon slurry based on ethanol, polyvinylpyrrolidone (PVP) aqueous solution was used to prepare carbon slurry for microporous layer. The prepared gas diffusion layers (GDLs) were characterized by scanning electron microscopy, contact angle system and pore size distribution analyzer. It was found that the GDL prepared with PVP aqueous solution had higher gas permeability, as well as more homogeneous hydrophobicity. Moreover, the prepared GDLs were used in the cathode of fuel cell and evaluated with fuel cell performance and EIS analysis, and the GDL prepared with PVP aqueous solution indicated better fuel cell performance and lower ohmic resistance and mass transfer resistance.     

Fractal model for prediction of effective thermal conductivity of gas diffusion layer in proton exchange membrane fuel cell

The process of heat transfer within porous media is usually considered as a transport through large numbers of straight channels with uniform pore sizes. For the prediction of effective thermal conductivity of gas diffusion layer (GDL), morphological properties such as the tortuosity of channels and pore-size distribution of this porous layer should be considered. Thus in this article, novel parallel and series-parallel prediction models of effective thermal conductivity for the GDL in proton exchange membrane fuel cell (PEMFC) have been derived by fractal theoretical characterization of the real microstructure of GDL. The prediction of fractal parallel model for carbon paper, a basal material of the GDL, is in good agreement with the reference value supplied by Toray Inc. The prediction results from the proposed models are also reasonable because they are distributed between the upper and lower bounds. Parametric effect has been investigated by using the presented models in dimensionless formalism. It can be concluded that dimensionless effective thermal conductivity (k^′eff${k^{\prime }}_{\text{eff}}$) has a positive correlation with effective porosity (?) or the pore-area fractal dimension (D_p) when k_s/k_g < 1; whereas it has a negative correlation with ? or D_p when k_s/k_g > 1 and with tortuous fractal dimension (D_t) whether k_s/k_g < 1 or not. Furthermore, these fractal models have been modified by considering the effect of polytetrafluoroethylene (PTFE) incorporated into the pore spaces of carbon paper, and the corresponding model prediction shows that there is an increase in the effective thermal conductivity due to the filling of PTFE that has high thermal conductivity.     

Study on ice-melting performance of gradient gas diffusion layer in proton exchange membrane fuel cell

In this study, a three-dimensional model was established using the lattice Boltzmann method (LBM) to study the internal ice melting process of the gas diffusion layer (GDL) of the proton exchange membrane fuel cell (PEMFC). The single-point second-order curved boundary condition was adopted. The effects of GDL carbon fiber number, growth slope of the number of carbon fibers and carbon fiber diameter on ice melting were studied. The results were revealed that the temperature in the middle and lower part of the gradient distribution GDL is significantly higher than that of the no-gradient GDL. With the increase of the growth slope of the number of carbon fiber, the temperature and melting rate gradually increase, and the position of the solid-liquid interface gradually decreases. The decrease in the number of carbon fibers has a similar effect as the increase in the growth slope of the number of carbon fibers. In addition, as the diameter of the carbon fiber increases, the position of the solid-liquid interface gradually decreases first and then increases.     

Effect of water distribution in gas diffusion layer on proton exchange membrane fuel cell performance

Water management of proton exchange membrane fuel cells remains a prominent issue in research concerning fuel cells. In this study, the gas diffusion layer (GDL) of a fuel cell is partially treated with a hydrophobic agent, and the effect of GDL hydrophobicity on the water distribution in the fuel cell is examined. First, the effect of the position of the cathode GDL hydrophobic area relative to the channel on the fuel cell performance is investigated. Then, the water distribution in the fuel cell cathode GDL is observed using X-ray imaging. The experimental results indicate that when the hybrid GDL's hydrophobic area lies on the channel, water tends to accumulate under the rib, and the water content in the channel is low; this improves the fuel cell performance. When the hydrophobic area is under the rib, the water distribution is more uniform, but the performance deteriorates.     

Gas diffusion layer for proton exchange membrane fuel cells—A review

Gas diffusion layer (GDL) is one of the critical components acting both as the functional as well as the support structure for membrane-electrode assembly in the proton exchange membrane fuel cell (PEMFC). The role of the GDL is very significant in the H₂/air PEM fuel cell to make it commercially viable. A bibliometric analysis of the publications on the GDLs since 1992 shows a total of 400+ publications (>140 papers in the Journal of Power Sources alone) and reveals an exponential growth due to reasons that PEMFC promises a lot of potential as the future energy source for varied applications and hence its vital component GDL requires due innovative analysis and research. This paper is an attempt to pool together the published work on the GDLs and also to review the essential properties of the GDLs, the method of achieving each one of them, their characterization and the current status and future directions. The optimization of the functional properties of the GDLs is possible only by understanding the role of its key parameters such as structure, porosity, hydrophobicity, hydrophilicity, gas permeability, transport properties, water management and the surface morphology. This paper discusses them in detail to provide an insight into the structural parts that make the GDLs and also the processes that occur in the GDLs under service conditions and the characteristic properties. The required balance in the properties of the GDLs to facilitate the counter current flow of the gas and water is highlighted through its characteristics.     

Thermal and electrochemical performance analysis of a proton exchange membrane fuel cell under assembly pressure on gas diffusion layer

In this study, the effect of clamping pressure on the performance of a proton exchange membrane fuel cell (PEMFC) is investigated for three different widths of channel. The deformation of gas diffusion layer (GDL) due to clamping pressure is modeled using a finite element method, and the results are applied as inputs to a CFD model. The CFD analysis is based on finite volume method in non-isothermal condition. Also, a comparison is made between three cases to identify the geometry that has the best performance. The distribution of temperature, current density and mole fraction of oxygen are investigated for the geometry with best performance. The results reveal that by decreasing the width of channel, the performance of PEMFC improves due to increase of flow velocity. Also, it is found that intrusion of GDL into the gas flow channel due to assembly pressure deteriorates the PEMFC performance, while decrease of GDL thickness and GDL porosity have smaller effects. It is shown that assembly pressure has a minor effect on temperature profile in the membrane-catalyst interface at cathode side. Also, assembly pressure has a significant effect on ohmic and concentration losses of PEMFC at high current densities.     

Liquid and oxygen transport in defective bilayer gas diffusion material of proton exchange membrane fuel cell

In this paper, pore network simulations are carried out to explore the effects of micro porous layer (MPL) and its crack location on the liquid and oxygen transport in the gas diffusion material (GDM) of proton exchange membrane fuel cell (PEMFC). The constructed network is composed of cubic pores connected by throats of square cross section. The GDM is partially screened by the land, and the MPL is assumed to have a crack. When the MPL crack is considered under the land in the model, the predicted results agree with experimental findings regarding the effect of MPL on the liquid saturation and distribution in the GDM. This indicates that the liquid may prefer to flow through the MPL crack under the land. The role of MPL in the fuel cell performance is revealed to be dependent on the oxygen effective diffusivity of MPL and GDL. Therefore, caution should be taken before employing the MPL to improve the cell performance. Based on the present studies, some guidelines are gained for the GDM design and optimization.     

Freezing characteristics of supercooled water in gas diffusion layer of proton exchange membrane fuel cells

The freezing characteristics of supercooled water in a gas diffusion layer (GDL), which are the bases for the cold start-up of proton exchange membrane fuel cells (PEMFCs), were investigated. An experimental apparatus for noncontact temperature measurement and observation systems was developed. GDL and GDL with a microporous layer (MPL) were prepared, and freezing experiments using a water-containing GDL under various cooling rates were performed with variations in polytetrafluoroethylene (PTFE) content and water saturation. Furthermore, based on the experimental results, the freezing initiation probability was theoretically investigated to elucidate the freezing characteristics. Results showed that, with increasing supercooling of water in GDL, the freezing probability of water increased abruptly. The effect of saturation showed a different trend depending on PTFE addition. For the GDL without PTFE, the freezing initiations occurred at approximately 6 °C of supercooling degree, and the probability approached 1.0 at approximately 9.5–11.5 °C, with saturation dependency. In contrast, for both GDL and GDL + MPL containing PTFE, the initiation temperature characteristics were relatively similar, which were approximately 8–12 °C, regardless of the saturation and PTFE content. In these cases, the ice-nucleating activity of water in the GDL was possibly stronger than that in the MPL.     

Effect of hydrophilic pipe structure of proton exchange membrane fuel cell on water removal from the gas diffusion layer surface

In a proton exchange membrane fuel cell (PEMFC), effective GDL surface water elimination is significant to water management. This paper used the volume-of-fluid method (VOF) method to carry out simulation research on transferring liquid water in the flow channel with a hydrophilic pipe. The findings indicated that compared with a straight channel, a hydrophilic pipe structure could effectively remove water from the gas diffusion surface (GDL) and reduce the surface water coverage of the GDL. With the increase in the diameter and height of the pipe structure, the GDL surface's water coverage first increased and then decreased, and it was less with the pipe structure than with the direct flow channel. The removal rate of water on the GDL surface was accelerated. The spacing of hydrophilic pipes has a significant impact on the transportation of water. As the spacing increases, the removal rate of water on the GDL surface slowed. A hydrophilic pipe structure with a diameter of 75 μm, a height of 400 μm, and spacing of 300 μm has good water removal performance on the GDL surface. This research work proposes a new internal structure design of the flow channel, which has specific implications for removing water on the GDL surface.