Thermophysical properties and devitrification of SrO–La2O3–Al2O3–B2O3–SiO2-based glass sealant for solid oxide fuel/electrolyzer cells

Thermal behaviors and stability of glass/glass–ceramic-based sealant materials are critical issues for high temperature solid oxide fuel/electrolyzer cells. To understand the thermophysical properties and devitrification behavior of SrO–La₂O₃–Al₂O₃–B₂O₃–SiO₂ system, glasses were synthesized by quenching (25 − X)SrO–20La₂O₃–(7 + X)Al₂O₃–40B₂O₃–8SiO₂ oxides, where X was varied from 0.0 mol% to 10.0 mol% at 2.5 mol% interval. Thermal properties were characterized by dilatometry and differential scanning calorimetry (DSC). Microstructural studies were performed by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). All the compositions have a glass transition temperature greater than 620 °C and a crystallization temperature greater than 826 °C. Also, all the glasses have a coefficient of thermal expansion (CTE) between 9.0 × 10⁻⁶ K⁻¹ and 14.5 × 10⁶ K⁻¹ after the first thermal cycle. La₂O₃ and B₂O₃ contribute to glass devitrification by forming crystalline LaBO₃. Al₂O₃ stabilizes the glasses by suppressing devitrification. Significant improvement in devitrification resistance is observed as X increases from 0.0 mol% to 10.0 mol%.     

Steam reforming of ethanol over Co3O4–Fe2O3 mixed oxides

Co₃O₄, Fe₂O₃ and a mixture of the two oxides Co–Fe (molar ratio of Co₃O₄/Fe₂O₃ = 0.67 and atomic ratio of Co/Fe = 1) were prepared by the calcination of cobalt oxalate and/or iron oxalate salts at 500 °C for 2 h in static air using water as a solvent/dispersing agent. The catalysts were studied in the steam reforming of ethanol to investigate the effect of the partial substitution of Co₃O₄ with Fe₂O₃ on the catalytic behaviour. The reforming activity over Fe₂O₃, while initially high, underwent fast deactivation. In comparison, over the Co–Fe catalyst both the H₂ yield and stability were higher than that found over the pure Co₃O₄ or Fe₂O₃ catalysts. DRIFTS-MS studies under the reaction feed highlighted that the Co–Fe catalyst had increased amounts of adsorbed OH/water; similar to Fe₂O₃. Increasing the amount of reactive species (water/OH species) adsorbed on the Co–Fe catalyst surface is proposed to facilitate the steam reforming reaction rather than decomposition reactions reducing by-product formation and providing a higher H₂ yield.     

Plasma-reduced Ni/γ–Al2O3 and CeO2–Ni/γ–Al2O3 catalysts for improving dry reforming of propane

Pristine Ni/γ–Al₂O₃ and CeO₂–Ni/γ–Al₂O₃ catalysts were prepared by co-impregnation technique for dry reforming of propane. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) were used to examine the structure and morphology of the catalysts before and after the reforming reactions. The excellent interaction between catalyst active phases was observed in both CeO₂–Ni/γ–Al₂O₃ and Ni/γ–Al₂O₃ stabilized with polyethelene glycol (Ni/γ–Al₂O₃–PEG). Towards C₃H₈ and CO₂ conversion, the CeO₂–Ni/γ–Al₂O₃ and Ni/γ–Al₂O₃–PEG showed improved catalytic activity when compared to the pristine Ni/γ–Al₂O₃ catalyst. Interestingly, high H₂ concentration was achieved with the CeO₂–Ni/γ–Al₂O₃ and high CO concentration with the Ni/γ–Al₂O₃–PEG, which is due to the nanoconfinement of nickel particles within the support and favorable metal-support interaction as a result of plasma reduction. The CeO₂–Ni/γ–Al₂O₃ catalyst exhibited better stability for anti-sintering and coke resistance, thus exhibiting high reactivity and durability in the dry reforming.     

A study on electrical conductivity of chemosynthetic Al2O3–2SiO2 geoploymer materials

Al₂O₃–2SiO₂ amorphous powders are synthesized by sol–gel method with tetraethoxysilane (TEOS) and aluminum nitrate (ANN) as the starting materials. The microstructure and phase structure of the powders are investigated by SEM and XRD analysis. Geopolymer materials samples are prepared by mechanically mixing stoichiometric amounts of calcined Al₂O₃–2SiO₂ powders and sodium silicate solutions to allow a mass ratio of Na₂O/Al₂O₃ = 0.4, 0.375, 0.35, 0.325, 0.288, 0.26, 0.23 or 0.2 separately, and finally to form a homogenous slurry at a fixed H₂O/Na₂O mole ratio = 11.7. The results show that the synthetic Al₂O₃–2SiO₂ powders have polycondensed property and their compressive strengthes are similar to that of nature metakaolin geopolymer materials. The results also show that the water consumption is not the main influencing factor on electrical conductivity of harden geopolymer materials but it can intensively affect the microstructure of geopolymer materials. In addition, the electrical conductivity of harden geopolymer sample is investigated, and the results show that the geopolymer materials have a high ionic electrical conductivity of about 1.5 × 10⁻⁶ S cm⁻¹ in air at room temperature.     

Hydrogen production from oxidative steam-reforming of n-propanol over Ni/Y2O3–ZrO2 catalysts

Oxidative steam reforming (OSR) of n-propanol was studied over new Ni catalysts (ca. 7% Ni wt/wt) supported on Y₂O₃–ZrO₂ oxides with different yttrium content (2–41 % Y₂O₃ wt/wt). Materials were characterized by X-ray diffraction, temperature-programmed reduction, X-ray photoelectron and Raman spectroscopy, scanning electron microscopy with energy dispersive X-ray analysis and high resolution transmission electron microscopy. Samples were used in calcined form and tested in the temperature range 673–773 K using a reactant feed of n-propanol/water/O₂ at a molar ratio 1/9/0.5. Hydrogen production is related with the support composition and Ni dispersion.     

Hydrogen production by steam reforming of ethanol over mesoporous Ni–Al2O3–ZrO2 aerogel catalyst

A mesoporous Ni–Al₂O₃–ZrO₂ aerogel (Ni–AZ) catalyst was prepared by a single-step epoxide-driven sol–gel method and a subsequent supercritical CO₂ drying method. For comparison, a mesoporous Al₂O₃–ZrO₂ aerogel (AZ) support was prepared by a single-step epoxide-driven sol–gel method, and subsequently, a mesoporous Ni/Al₂O₃–ZrO₂ aerogel (Ni/AZ) catalyst was prepared by an incipient wetness impregnation method. The effect of preparation method on the physicochemical properties and catalytic activities of Ni–AZ and Ni/AZ catalysts was investigated. Although both catalysts retained a mesoporous structure, Ni/AZ catalyst showed lower surface area than Ni–AZ catalyst. From TPR, XRD, and H₂–TPD results, it was revealed that Ni–AZ catalyst retained higher reducibility and higher nickel dispersion than Ni/AZ catalyst. In the hydrogen production by steam reforming of ethanol, both catalysts showed a stable catalytic performance with complete conversion of ethanol. However, Ni–AZ catalyst showed higher hydrogen yield than Ni/AZ catalyst. Superior textural properties, high reducibility, and high nickel surface area of Ni–AZ catalyst were responsible for its enhanced catalytic performance in the steam reforming of ethanol.     

Oxidative steam reforming of ethanol over Ni/Al2O3 catalysts promoted by CeO2, ZrO2 and CeO2–ZrO2

Oxidative steam reforming of ethanol at low oxygen to ethanol ratios was investigated over nickel catalysts on Al₂O₃ supports that were either unpromoted or promoted with CeO₂, ZrO₂ and CeO₂–ZrO₂. The promoted catalysts showed greater activity and a higher hydrogen yield than the unpromoted catalyst. The characterization of the Ni-based catalysts promoted with CeO₂ and/or ZrO₂ showed that the variations induced in the Al₂O₃ by the addition of CeO₂ and/or ZrO₂ alter the catalyst's properties by enhancing Ni dispersion and reducing Ni particle size. The promoters, especially CeO₂–ZrO₂, improved catalytic activity by increasing the H₂ yield and the CO₂/CO and the H₂/CO values while decreasing coke formation. This results from the addition of ZrO₂ into CeO₂. This promoter highlights the advantages of oxygen storage capacity and of mobile oxygen vacancies that increase the number of surface oxygen species. The addition of oxygen facilitates the reaction by regenerating the surface oxygenation of the promoters and by oxidizing surface carbon species and carbon-containing products.     

Syngas production by CO2 reforming of coke oven gas over Ni/La2O3–ZrO2 catalysts

Syngas production by CO₂ reforming of coke oven gas (COG) was studied in a fixed-bed reactor over Ni/La₂O₃–ZrO₂ catalysts. The catalysts were prepared by sol–gel technique and tested by XRF, BET, XRD, H₂-TPR, TEM and TG–DSC. The influence of nickel loadings and calcination temperature of the catalysts on reforming reaction was measured. The characterization results revealed that all of the catalysts present excellent resistance to coking. The catalyst with appropriate nickel content and calcination temperature has better dispersion of active metal and higher conversion. It is found that the Ni/La₂O₃–ZrO₂ catalyst with 10 wt% nickel loading provides the best catalytic activity with the conversions of CH₄ and CO₂ both more than 95% at 800 °C under the atmospheric pressure. The Ni/La₂O₃–ZrO₂ catalysts show excellent catalytic performance and anti-carbon property, which will be of great prospects for catalytic CO₂ reforming of COG in the future.     

Development of Fe2O3–TiO2 mixed oxide incorporated Ni–P coating for electrocatalytic hydrogen evolution reaction

Considering the electronic parameters and chemical characteristics, a synergistic catalytic effect of Fe₂O₃ along with TiO₂ could be achieved for electrochemical reactions if both the oxides are produced in a mixed oxide form. The present study explored the mixed oxide composite viz; Fe₂O₃–TiO₂, synthesized via thermal decomposition method, to increase the catalytic efficiency of Ni–P electrodes, the well known catalytic electrodes for hydrogen evolution reaction in alkaline medium. The incorporation of the Fe₂O₃–TiO₂ mixed oxide into Ni–P matrix substantially reduced overpotential during hydrogen evolution reaction (HER) in 32% NaOH solution. A significant improvement on the electrochemical activity of the Ni–P coated electrodes was achieved as evidenced from the results of Tafel and impedance studies. The incorporation of Fe₂O₃–TiO₂ mixed oxide composite into the Ni–P matrix has improved both metallurgical and electrochemical characteristics and hence its amount of incorporation should be optimum. The electrodes exhibited high stability under dynamic experimental conditions. The role of the composite and the possible mechanism are discussed in this paper.     

Characterization and activity test of commercial Ni/Al2O3, Cu/ZnO/Al2O3 and prepared Ni–Cu/Al2O3 catalysts for hydrogen production from methane and methanol fuels

In this study, methane and methanol steam reforming reactions over commercial Ni/Al₂O₃, commercial Cu/ZnO/Al₂O₃ and prepared Ni–Cu/Al₂O₃ catalysts were investigated. Methane and methanol steam reforming reactions catalysts were characterized using various techniques. The results of characterization showed that Cu particles increase the active particle size of Ni (19.3 nm) in Ni–Cu/Al₂O₃ catalyst with respect to the commercial Ni/Al₂O₃ (17.9). On the other hand, Ni improves Cu dispersion in the same catalyst (1.74%) in comparison with commercial Cu/ZnO/Al₂O₃ (0.21%). A comprehensive comparison between these two fuels is established in terms of reaction conditions, fuel conversion, H₂ selectivity, CO₂ and CO selectivity. The prepared catalyst showed low selectivity for CO in both fuels and it was more selective to H₂, with H₂ selectivities of 99% in methane and 89% in methanol reforming reactions. A significant objective is to develop catalysts which can operate at lower temperatures and resist deactivation. Methanol steam reforming is carried out at a much lower temperature than methane steam reforming in prepared and commercial catalyst (275–325 °C). However, methane steam reforming can be carried out at a relatively low temperature on Ni–Cu catalyst (600–650 °C) and at higher temperature in commercial methane reforming catalyst (700–800 °C). Commercial Ni/Al₂O₃ catalyst resulted in high coke formation (28.3% loss in mass) compared to prepared Ni–Cu/Al₂O₃ (8.9%) and commercial Cu/ZnO/Al₂O₃ catalysts (3.5%).     

Effects of Y2O3-modification to Ni/γ-Al2O3 catalysts on autothermal reforming of methane with CO2 to syngas

The effects of Y₂O₃-modification to Ni/γ-Al₂O₃ catalysts on autothermal reforming of methane to syngas were investigated. It was found that the introduction of Y₂O₃ (5%, 8%, 10%) lead to significant improvement in catalytic activity and stability, and the H₂/CO ratio could be adjusted via controlling the O₂/CO₂ ratio of the feed gas. According to the characterization results of catalysts before and after reaction, it was found that the Y₂O₃·γ-Al₂O₃ supported Ni catalysts had higher NiO reducibility, smaller Ni particle size, higher Ni dispersion and stronger basicity than those of the Ni/γ-Al₂O₃ catalysts. The analysis of catalysts after reaction showed that the addition of Y₂O₃ inhibited the Ni sintering, changed the type of coke and decreased the amount of coke on the catalysts. All the experimental results indicated that the introduction of Y₂O₃ to Ni/γ-Al₂O₃ resulted in excellent catalytic performances in autothermal reforming of methane, and Y₂O₃ played important roles in preventing metal sintering and coke deposition via controlling NiO reducibility, Ni particle size and dispersion, and basicity of catalysts.     

Effects of noble metal-doping on Ni/La2O3–ZrO2 catalysts for dry reforming of coke oven gas

A series of noble metal (Ru, Pd, Ag) doped Ni catalysts supported on La₂O₃–ZrO₂ mixed oxide were prepared using the sol–gel method and evaluated for use in dry reforming of coke oven gas (COG). The catalysts were investigated by means of N₂ adsorption–desorption, XRD, H₂-TPR, TPH, TEM and TG–DSC. TPH analysis revealed that two carbonaceous species formed on the used catalysts and that the low-temperature carbon species was sufficiently active for the reforming reaction. TEM observations indicated that highly dispersed and small metal particles were formed, suppressing coke deposition and improving catalytic performance. The test results indicated that the addition of trace amounts of noble metals effectively promotes catalytic activity. The 0.1Ru–10Ni/8LZ catalyst showed the highest performance among the bimetallic catalysts, because of the strong synergetic effect between Ru and Ni via the formation of a Ru–Ni alloy, which will be promising catalysts in the catalytic dry reforming of COG.     

Thermal performance of an oscillating heat pipe with Al2O3–water nanofluids

An experimental investigation was performed on the thermal performance of an oscillating heat pipe (OHP) charged with base water and spherical Al₂O₃ particles of 56 nm in diameter. The effects of filling ratios, mass fractions of alumina particles, and power inputs on the total thermal resistance of the OHP were investigated. Experimental results showed that the alumina nanofluids significantly improved the thermal performance of the OHP, with an optimal mass fraction of 0.9 wt.% for maximal heat transfer enhancement. Compared with pure water, the maximal thermal resistance was decreased by 0.14 °C/W (or 32.5%) when the power input was 58.8 W at 70% filling ratio and 0.9% mass fraction. By examining the inner wall samples, it was found that the nanoparticle settlement mainly took place at the evaporator. The change of surface condition at the evaporator due to nanoparticle settlement was found to be the major reason for the enhanced thermal performance of the alumina nanofluid-charged OHP.     

Hydrogen production by steam reforming of ethanol over mesoporous Ni–Al2O3–ZrO2 xerogel catalysts: Effect of nickel content

Hydrogen production by steam reforming of ethanol over mesoporous Ni–Al₂O₃–ZrO₂ xerogel catalysts (denoted as XNiAZ) with different nickel content (X, wt%) was studied. A single-step epoxide-driven sol–gel method was employed for the preparation of the catalysts. The effect of nickel content of XNiAZ catalysts on their physicochemical properties and catalytic activities was investigated. All the XNiAZ catalysts exhibited a well-developed mesoporous structure and they dominantly showed an amorphous NiO–Al₂O₃–ZrO₂ composite phase, leading to high dispersion of NiO. Nickel surface area and reducibility of XNiAZ catalysts showed volcano-shaped trends with respect to nickel content. Nickel surface area of XNiAZ catalysts played a key role in determining the catalytic performance in the steam reforming of ethanol; an optimal nickel content was required for maximum production of hydrogen. Among the catalysts tested, 15NiAZ catalyst with the highest nickel surface area exhibited the best catalytic performance in the steam reforming of ethanol. In addition, 15NiAZ catalyst showed high and stable hydrogen yields under different total feed rate, demonstrating its potential applicability in large-scale hydrogen production.     

Rh promoted and ZrO2/Al2O3 supported Ni/Co based catalysts: High activity for CO2 reforming,steam–CO2 reforming and oxy–CO2 reforming of CH4

Ni (2.5 wt%) and Co (2.5 wt%) supported over ZrO₂/Al₂O₃ were prepared by following a hydrolytic co-precipitation method. The synthesized catalysts were further promoted by Rh incorporation (0.01–1.00 wt%) and tested for their catalytic performance for dry CO₂ reforming, combined steam–CO₂ reforming and oxy–CO₂ reforming of methane for production of syngas. The catalysts were characterized by using N₂ physical adsorption, XRD, H₂–TPR, SEM, CO₂–TPD, NH₃–TPD, TEM and TGA. The results revealed that ZrO₂ phase was in crystalline form in the catalysts along with amorphous Al oxides. Ni and Co were confirmed to be in their respective spinel phases that were reducible to metallic form at 800 °C under H₂. Ni and Co were well dispersed with their nano-crystalline nature. The catalyst with 0.2% loading of Rh showed superior performance in the studied reactions for reforming of methane. This catalyst also showed good coke resistance ability for dry CO₂ reforming reaction with 3.8 wt% of carbon formation during the reaction as compared to 11.6 wt% carbon formation over the catalyst without Rh. The catalyst performance was stable throughout the reaction time for CH₄ conversions, irrespective of carbon formation with slight decline (～1%) in CO₂ conversion. For dry CO₂ reforming reaction, this catalyst showed good conversion for both CH₄ and CO₂ (67.6% and 71.8% respectively) with a H₂/CO ratio of 0.84, while for the Oxy-CO₂ reforming reaction, the activity was superior with CH₄ and CO₂ conversions (73.7% and 83.8% respectively) and H₂/CO ratio of 1.05.     

Production of hydrogen via steam reforming of biofuels on Ni/CeO2–Al2O3 catalysts promoted by noble metals

The catalytic activity of Ni/CeO₂–Al₂O₃ catalysts modified with noble metals (Pt, Ir, Pd and Ru) was investigated for the steam reform of ethanol and glycerol. The catalysts were characterized by the following techniques: Energy-dispersive X-ray, BET, X-ray diffraction, temperature-programmed reduction, UV–vis diffuse reflectance spectroscopy and X-ray absorption near edge structure (XANES). The results showed that the formation of inactive nickel aluminate was prevented by the presence of CeO₂ dispersed on alumina. The promoting effect of noble metals included a decrease in the reduction temperatures of NiO species interacting with the support, due to the hydrogen spillover effect. It was seen that the addition of noble metal stabilized the Ni sites in the reduced state along the reforming reaction, increasing the ethanol and glycerol conversions and decreasing the coke formation. The higher catalytic performance for the ethanol steam reforming at 600 °C and glycerol steam reforming was obtained for the NiPd and NiPt catalysts, respectively, which presented an effluent gaseous mixture with the highest H₂ yield with reasonably low amounts of CO.     

Novel Ni–ZrO2 catalyst doped with Yb2O3 for ethanol steam reforming

A type of Yb₂O₃ doped Ni–ZrO₂ catalyst for ethanol steam reforming was developed, and displayed excellent catalyzing performance for the selective formation of H₂ and CO₂. Over a Ni_1.25Zr₁Yb_0.8 catalyst, STY(H₂) can maintain stable at the level of 0.396 mol h⁻¹ g⁻¹ (data taken 120 h after the reaction started) under the reaction conditions of 0.5 MPa and 723 K, which was 1.6 times that (0.247 mol h⁻¹ g⁻¹) of the Yb-free counterpart Ni_1.25Zr₁. Characterization of the catalyst revealed that dissolution of an appropriate amount of Yb³⁺ ions in the zirconia host resulted in the formation of the Zr–Yb composite oxide with cubic-ZrO₂ structure, c-(Zr–Yb)O_z, which inhibited effectively the transformation of c-ZrO₂ to thermodynamically more stable m-ZrO₂, thus avoiding sintering of the (Zr–Yb)O_z composite. It was demonstrated that the doping of Yb₂O₃ to Ni–ZrO₂ changed also the valence states or the micro-environments of the Ni-species at the quasi-active surface of the tested catalyst, which was conducive to inhibiting agglomeration of the Ni_x⁰–Niⁿ⁺ species active catalytically, with resulting in maintaining the high metallic nickel dispersion and inhibiting coking. The aforementioned two factors both contributed to improving the activity and operating stability as well as heat-resistant quality of the catalyst.     

Synthesis and electrochemistry of cubic rocksalt Li–Ni–Ti–O compounds in the phase diagram of LiNiO2–LiTiO2–Li[Li1/3Ti2/3]O2

On the basis of extreme similarity between the triangle phase diagrams of LiNiO₂–LiTiO₂–Li[Li_1/3Ti_2/3]O₂ and LiNiO₂–LiMnO₂–Li[Li_1/3Mn_2/3]O₂, new Li–Ni–Ti–O series with a nominal composition of Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) was designed and attempted to prepare via a spray-drying method. XRD identified that new Li–Ni–Ti–O compounds had cubic rocksalt structure, in which Li, Ni and Ti were evenly distributed on the octahedral sites in cubic closely packed lattice of oxygen ions. They can be considered as the solid solution between cubic LiNi_1/2Ti_1/2O₂ and Li[Li_1/3Ti_2/3]O₂ (high temperature form). Charge–discharge tests showed that Li–Ni–Ti–O compounds with appropriate compositions could display a considerable capacity (more than 80 mAh g⁻¹ for 0.2 ≤ z ≤ 0.27) at room temperature in the voltage range of 4.5–2.5 V and good electrochemical properties within respect to capacity (more than 150 mAh g⁻¹ for 0 ≤ z ≤ 0.27), cycleability and rate capability at an elevated temperature of 50 °C. These suggest that the disordered cubic structure in some cases may function as a good host structure for intercalation/deintercalation of Li⁺. A preliminary electrochemical comparison between Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) and Li_6/5Ni_2/5Ti_2/5O₂ indicated that charge–discharge mechanism based on Ni redox at the voltage of >3.0 V behaved somewhat differently, that is, Ni could be reduced to +2 in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ while +3 in Li_6/5Ni_2/5Ti_2/5O₂. Reduction of Ti⁴⁺ at a plateau of around 2.3 V could be clearly detected in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ with 0.27 ≤ z ≤ 0.5 at 50 °C after a deep charge associated with charge compensation from oxygen ion during initial cycle.