Plasma-nitrided austenitic stainless steel 316L as bipolar plate for PEMFC

Stainless steel bipolar plates for the polymer electrolyte membrane (PEM) fuel cell offer many advantages over conventional machined graphite. Austenitic stainless steel 316L is a traditional candidate for metal bipolar plates. However, the interfacial ohmic loss across the metallic bipolar plate and membrane electrode assembly due to corrosion increases the overall power output of PEMFC. Plasma nitriding was applied to improve the surface performance of 316L bipolar plates. A dense _γN${\gamma }_{\mathrm{N}}$ phase layer was formed on the surface. Polarization curves in the solution simulating PEMFC environment and interfacial contact resistance were measured. The results show that the corrosion resistance is improved and the interfacial contact resistance (ICR) is decreased after plasma nitriding. In comparison with the untreated 316L, the ICR between the carbon paper and passive film for the plasma-nitrided 316L decreases at the same condition and lowers with increasing pH value.     

Inductively coupled plasma nitriding of chromium electroplated AISI 316L stainless steel for PEMFC bipolar plate

Chromium electroplated AISI 316L stainless steel was nitrided using inductively coupled plasma (ICP) for application in the bipolar plate of a polymer electrolyte membrane fuel cell (PEMFC). A continuous and thin chromium nitride layer was formed at the surface of the samples after ICP nitriding for 2 h at 400 °C. The interfacial contact resistance (ICR) and corrosion resistance in simulated PEMFC operating conditions were higher than the required values, while they varied with the applied dc bias voltage during the nitriding process. The ICR value decreased with an increase in bias voltage. Potentiodynamic polarization measurements showed that all of the nitrided samples had excellent corrosion resistance with a current density of ∼10⁻⁷ A cm⁻² at the cathode. It was also found that the oxygen content at the surface was not increased after the corrosion test. X-ray diffractometry (XRD), field emission scanning electron microscopy (FE-SEM), and Auger electron spectroscopy (AES) were used to analyze the effect of plasma nitriding.     

Thermal nitridation of chromium electroplated AISI316L stainless steel for polymer electrolyte membrane fuel cell bipolar plate

The electrical and corrosion properties of surface-nitrided AISI316L stainless steel are evaluated to assess the potential use of this material as a bipolar plate for a polymer electrolyte membrane fuel cell. Chromium is electroplated on the surface of the AISI316L stainless steel before nitridation. The nitriding condition is selected so as to form Cr₂N nitride only and the result is compared with that of a CrN + Cr₂N nitride coating. The stainless steels with the Cr₂N nitride protective coating layer exhibit better interfacial contact resistance and corrosion resistance than the as-rolled or (CrN + Cr₂N)-coated AISI316L stainless steels.     

Anticorrosion properties of Ta-coated 316L stainless steel as bipolar plate material in proton exchange membrane fuel cells

In order to reduce the cost, volume and weight of the bipolar plates used in the proton exchange membrane fuel cells (PEMFC), more attention is being paid to metallic materials, among which 316L stainless steel (SS316L) is quite attractive. In this study, metallic Ta is deposited on SS316L using physical vapor deposition (PVD) to enhance the corrosion resistance of the bipolar plates. Simulative working environment of PEMFC is applied for testing the corrosion property of uncoated and Ta-coated SS316L. X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods (potentiodynamic and potentiostatic polarization) are also used for analyzing characteristics of uncoated and Ta-coated SS316L. Results show that, Ta-coated SS316L has significantly better anticorrosion property than that of uncoated SS316L, with corrosion current densities of uncoated SS316L being 44.61 μA cm⁻² versus 9.25 μA cm⁻² for Ta-coated SS316L, a decrease of about 5 times. Moreover, corrosion current densities of Ta-coated SS316L in both simulative anode (purged with H₂) and cathode (purged with air) conditions are smaller than those of uncoated SS316L.     

Improvement of corrosion resistance and electrical conductivity of 304 stainless steel using close field unbalanced magnetron sputtered carbon film

Carbon film has been deposited on 304 stainless steel (SS304) using close field unbalanced magnetron sputter ion plating (CFUBMSIP) to improve the corrosion resistance and electrical conductivity of SS304 acting as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The corrosion resistance, interfacial contact resistance (ICR), surface morphology and contact angle with water of the bare and carbon-coated SS304 are investigated. The carbon-coated SS304 shows good corrosion resistance in the simulated cathode and anode PEMFC environment. The ICR between the carbon-coated SS304 and the carbon paper is 8.28-2.59 mΩ cm² under compaction forces between 75 and 360 N cm⁻². The contact angle of the carbon-coated SS304 with water is 88.6°, which is beneficial to water management in the fuel cell stack. These results indicate that the carbon-coated SS304 exhibits high corrosion resistance, low ICR and hydrophobicity and is a promising candidate for bipolar plates.     

Effects of niobium and titanium addition and surface treatment on electrical conductivity of 316 stainless steel as bipolar plates for proton-exchange membrane fuel cells

Niobium and titanium are added to 316 stainless steel, and then heat treatment and surface treatment are performed on the 316 stainless steel and the Nb- and Ti-added alloys. All samples exhibit enhanced electrical conductivity after surface treatment but have low electrical conductivity before surface treatment due to the existence of non-conductive passive films on the alloy surfaces. In particular, the Nb- and Ti-added alloys experience a remarkable enhancement of electrical conductivity and cell performance compared with the original 316 stainless steel. Surface characterization reveals the presence of small carbide particles on the alloy surface after treatment, whereas the untreated alloys have a flat surface structure. Cr₂₃C₆ forms on the 316 stainless steel, and NbC and TiC forms on the Nb- and Ti-added alloys, respectively. The enhanced electrical conductivity after surface treatment is attributed to the formation of these carbide particles, which possibly act as electro-conductive channels through the passive film. Furthermore, NbC and TiC are considered to be more effective carbides than Cr₂₃C₆ as electro-conductive channels for stainless steel.     

Chromium nitride/Cr coated 316L stainless steel as bipolar plate for proton exchange membrane fuel cell

Chromium nitride/Cr coating has been deposited on surface of 316L stainless steel to improve conductivity and corrosion resistance by physical vapor deposition (PVD) technology. Electrochemical behaviors of the chromium nitride/Cr coated 316L stainless steel are investigated in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environments, and interfacial contact resistance (ICR) are measured before and after potentiostatic polarization at anodic and cathodic operation potentials for PEMFC. The chromium nitride/Cr coated 316L stainless steel exhibits improved corrosion resistance and better stability of passive film either in the simulated anodic or cathodic environment. In comparison to 316L stainless steel with air-formed oxide film, the ICR between the chromium nitride/Cr coated 316L stainless steel and carbon paper is about 30 mΩ cm² that is about one-third of bare 316L stainless steel at the compaction force of 150 N cm⁻². Even stable passive films are formed in the simulated PEMFC environments after potentiostatic polarization, the ICR of the chromium nitride/Cr coated 316L stainless steel increases slightly in the range of measured compaction force. The excellent performance of the chromium nitride/Cr coated 316L stainless steel is attributed to inherent characters. The chromium nitride/Cr coated 316L stainless steel is a promising material using as bipolar plate for PEMFC.     

An investigation into nickel implanted 316L stainless steel as a bipolar plate for PEM fuel cell

A nickel-rich layer about 100 μm in thickness with improved conductivity was formed on the surface of austenitic stainless steel 316L (SS316L) by ion implantation. The effect of ion implantation on the corrosion behavior of SS316L was investigated in 0.5 M H₂SO₄ with 2 ppm HF solution at 80 °C by potentiodynamic test. In order to investigate the chemical stability of the ion implanted SS316L, the potentiostatic test was conducted in an accelerated cathode environment and the solutions after the potentiostatic test were analyzed by inductively coupled plasma atomic emission spectrometer (ICP-AES). The results of potentiodynamic test show that the corrosion potential of SS316L is shifted toward the positive direction from −0.3 V versus SCE to −0.05 V versus SCE in anode environment and the passivation current density at 0.6 V is reduced from 11.26 to 7.00 μA cm⁻² in the cathode environment with an ion implantation dose of 3 × 10¹⁷ ions cm⁻². The potentiostatic test results indicate that the nickel implanted SS316L has higher chemical stability in the accelerated cathode environment than the bare SS316L, due to the increased amount of metallic Ni in the passive layer. The ICP results are in agreement with the electrochemical test results that the bare SS316L has the highest dissolution rate in both cathode and anode environments and the Ni implantation markedly reduces the dissolution rate. A significant improvement of interfacial contact resistance (ICR) is achieved for the SS316L implanted with nickel as compared to the bare SS316L, which is attributed to the reduction in passive layer thickness caused by the nickel implantation. The ICR values for implanted specimens increase with increasing dose.     

Active screen plasma nitriding of 316 stainless steel for the application of bipolar plates in proton exchange membrane fuel cells

Proton exchange membrane fuel cell (PEMFC) has attracted considerable interest because of its superb performance, and many researches are focused on the development of high-performance, long-life bipolar plates. Stainless steel bipolar plates offer many advantages over the conventional graphite bipolar plates, such as low material and fabrication cost, excellent mechanical behaviour and ease of mass production. However, the insufficient corrosion resistance and relatively high interfacial contact resistance (ICR) become the major obstacles to the widespread use of stainless steel bipolar plates. In this work, active screen plasma nitriding (ASPN), a novel plasma nitriding technique, was used to modify the surface of 316 austenitic stainless steel. A variety of analytical techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), glow discharge optical emission spectrometer (GDOES), were employed to characterize the nitrided samples. The results reveal that a nitrogen supersaturated S-phase layer has been successfully produced on the surface of all nitrided 316 stainless steel samples. The interfacial contact resistance (ICR) value can be decreased dramatically after ASPN treatment and the corrosion resistance can also been improved. In addition, better corrosion resistance can be achieved by active screen plasma nitriding with a stainless steel screen than with a carbon steel screen. This technique could be used to improve the performance and lifespan of bipolar plates for fuel cells.     

Molybdenum nitride modified AISI 304 stainless steel bipolar plate for proton exchange membrane fuel cell

A molybdenum nitride diffusion coating has been prepared on the surface of AISI 304 stainless steel (304 SS) by plasma surface diffusion alloying method as bipolar plate for proton exchange membrane fuel cell (PEMFC). X-ray diffraction data shows that the molybdenum nitride is face-centered-cubic Mo₂N phase. The results of scanning electron microscopy in combination with energy-dispersive X-ray analysis spectrometer indicate that the as-prepared molybdenum nitride diffusion coating consists of a ∼3.5 μm surface layer (molybdenum nitride) and a ∼0.5 μm subsurface layer (Mo and N solid solution). In addition, the average contact angle with water for modified 304 SS is 91°, demonstrating the better hydrophobic property of the surface modified 304 SS as compared to the untreated ones with average contact angle of 68°. Potentiodynamic and potentiostatic testing in simulated PEFMC operating conditions (0.05 M H₂SO₄ + 2 ppm F⁻ solution at 70 °C purged with either hydrogen or air) as well as interfacial contact resistance (ICR) measurement imply that the molybdenum nitride modified 304 SS exhibits improved corrosion resistance and promising ICR.     

Corrosion resistance and interfacial contact resistance of TiN coated 316L bipolar plates for proton exchange membrane fuel cell

TiN coating is successfully deposited on 316L by multi-arc ion plating. Corrosion behavior of TiN coated 316L is studied in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environments using electrochemical method, and interfacial contact resistance (ICR) is measured before and after potentiostatic polarization at operation potential for PEMFC. The TiN coated 316L exhibits promising ICR and improved corrosion resistance in simulated aggressive PEMFC environments. Only general overall corrosion is observed after potentiostatic polarization. Stable passive film has formed on the surface of the TiN coated 316L after potentiostatic polarization at the operation potential and results in a slight increase in the ICR. These results indicate that the TiN coated 316L is a candidate bipolar plate material for PEMFC stacks.     

Improved anticorrosion properties and electrical conductivity of 316L stainless steel as bipolar plate for proton exchange membrane fuel cell by lower temperature chromizing treatment

The lower temperature chromizing treatment is developed to modify 316L stainless steel (SS 316L) for the application of bipolar plate in proton exchange membrane fuel cell (PEMFC). The treatment is performed to produce a coating, containing mainly Cr-carbide and Cr-nitride, on the substrate to improve the anticorrosion properties and electrical conductivity between the bipolar plate and carbon paper. Shot peening is used as the pretreatment to produce an activated surface on stainless steel to reduce chromizing temperature. Anticorrosion properties and interfacial contact resistance (ICR) are investigated in this study. Results show that the chromized SS 316L exhibits better corrosion resistance and lower ICR value than those of bare SS 316L. The chromized SS 316L shows the passive current density about 3E−7 A cm⁻² that is about four orders of magnitude lower than that of bare SS 316L. ICR value of the chromized SS 316L is 13 mΩ cm² that is about one-third of bare SS 316L at 200 N cm⁻² compaction forces. Therefore, this study clearly states the performance advantages of using chromized SS 316L by lower temperature chromizing treatment as bipolar plate for PEMFC.     

Tantalum nitride coated AISI 316L as bipolar plate for polymer electrolyte membrane fuel cell

Tantalum nitride (TaN) thin films are deposited on AISI 316L stainless steel by inductively coupled, plasma-assisted, reactive magnetron sputtering at various N₂ flow rates. TaN film behavior is investigated in simulated polymer electrolyte membrane fuel cell (PEMFC) conditions by using electrochemical measurement techniques for application as bipolar plates. The results of a potentio-dynamic polarization test under PEMFC cathodic and anodic conditions indicate that the corrosion current density of the TaN_x films is of the order of 10⁻⁷ A cm⁻² (at 0.6 V) and 10⁻⁸ A cm⁻² (at −0.1 V), respectively; these results are considerably better than the individual results for metallic Ta films and AISI 316L stainless steel. The TaN_x films exhibit superior stability in a potentio-static polarization test performed under PEMFC cathodic and anodic conditions. The interfacial contact resistance of the films is measured in the range of 50-150 N cm⁻², and the lowest value is 11 mΩ cm² at a compaction pressure of 150 N cm⁻².     

Influence of fluoride ions on corrosion performance of 316L stainless steel as bipolar plate material in simulated PEMFC anode environments

Corrosion performance of 316L stainless steel as a bipolar plate material in proton exchange membrane fuel cell (PEMFC) is studied under different simulated PEMFC anode conditions. Solutions of 1 × 10⁻⁵ M H₂SO₄ with a wide range of different F⁻ concentrations at 70 °C bubbled with hydrogen gas are used to simulate the PEMFC anode environments. Electrochemical methods, both potentiodynamic and potentiostatic, are employed to study the corrosion behavior. Scanning electron microscope (SEM) and atomic force microscope (AFM) are used to examine the surface morphology of the specimen after it is potentiostatic polarized in simulated PEMFC anode environments. X-ray photoelectron spectroscopy (XPS) analysis is used to identify the compositions and the depth profile of the passive film formed on the 316L stainless steel surface after it is polarized in simulated PEMFC anode environments. Mott–Schottky measurements are used to characterize the semiconductor passive films. The results of potentiostatic analyses show that corrosion currents increase with F⁻ concentrations. SEM examinations show that no localized corrosion occurs on the surface of 316L stainless steel and AFM measurement results indicate that the surface topography of 316L stainless steel becomes slightly rougher after polarized in solutions with higher concentration of F⁻. From the results of XPS analysis and Mott–Schottky measurements, it is determined that the passive film formed on 316L stainless steel is a single layer n-type semiconductor.     

Carbon film-coated 304 stainless steel as PEMFC bipolar plate

Carbon film-coated stainless steel (CFCSS) has been evaluated as a low-cost and small-volume substitute for graphite bipolar plate in polymer electrolyte membrane fuel cell (PEMFC). In the present work, AISI 304 stainless steel (304SS) plate was coated with nickel layer to catalyze carbon deposits at 680°C under C₂H₂/H₂ mixed gas atmosphere. Surface morphologies of carbon deposits exhibited strong dependence on the concentration of carbonaceous gas and a continuous carbon film with compact structure was obtained at 680 °C under C₂H₂/H₂ mixed gas ratio of 0.45. Systematic analyses indicated that the carbon film was composed of a highly ordered graphite layer and a surface layer with disarranged graphite structure. Both corrosion endurance tests and PEMFC operations showed that the carbon film revealed excellent chemical stability similar to high-purity graphite plate, which successfully protected 304SS substrate against the corrosive environment in PEMFC. We therefore predict CFCSS plates may practically replace commercial graphite plates in the application of PEMFC.     

(Titanium,chromium) nitride coatings for bipolar plate of polymer electrolyte membrane fuel cell

(Titanium, chromium) nitride [(Ti,Cr)N] coatings are synthesized on a 316L stainless-steel substrate by inductively-coupled, plasma-assisted, reactive direct current magnetron sputtering. The chemical and electrical properties of the coating are investigated from the viewpoint of it application to bipolar plates. Nanocrystallized Cr–Ti films are formed in the absence of nitrogen gas, while a hexagonal β-(Ti,Cr)₂N phase is observed at N₂ = 1.2 sccm. Well-crystallized (Ti,Cr)N films are obtained at N₂ > 2.0 sccm. The corrosion resistance of the coating is examined by potentiodynamic and potentiostatic tests in 0.05 M H₂SO₄ + 0.2 ppm HF solution at 80 °C, which simulates the operation conditions of a polymer electrolyte membrane fuel cell. The Davies method is used to measure the interfacial contact resistance between the sample and carbon paper. The (Ti,Cr)N coating exhibits the highest corrosion potential and lowest current density. In a cathode environment, the corrosion potential and current density are 0.33 V (vs. SCE) and <5 × 10⁻⁷ A cm⁻² (at 0.6 V), respectively. In an anode environment the corresponding values are 0.16 V and <−5 × 10⁻⁸ A cm⁻² at −0.1 V. The (Ti,Cr)N coatings exhibit excellent stability during potentiostatic polarization tests in both anode and cathode environments. The interfacial contact resistance decreases with deposition of the (Ti,Cr)N film, and a minimum value of 4.5 mΩ cm² is obtained at a compaction force of 150 N cm⁻², which indicates that the formation of oxide films can be successfully prevented by the (Ti,Cr)N film. Analysis with Auger electron spectroscopy reveals that the oxygen content at the surface decreases with increase in the nitrogen content.     

Corrosion characteristics of SS316L as bipolar plate material in PEMFC cathode environments with different acidities

The corrosion characteristics of SS316L in simulated proton exchange membrane fuel cell (PEMFC) environments with a wide range of H₂SO₄ concentrations have been systematically studied. Electrochemical methods, both potentiodynamic and potentiostatic, are employed to determine the corrosion parameters and the results show that corrosion resistance decreases with increasing H₂SO₄ concentrations. Scanning electron microscope (SEM) is used to examine the surface morphology of the specimens after potentiostatic polarized in simulated PEMFC cathode environments and the results indicate that local corrosion occurs under all the conditions studied and local corrosion is more severe with higher H₂SO₄ concentrations. Auger electron spectroscopy (AES) analysis is used to identify the composition and the depth profile of the passive film formed on the SS316L surface and the results show that the thickness of passive film decreases with increasing H₂SO₄ concentrations. Interfacial contact resistances (ICR) between SS316L polarized and carbon paper are measured and the results show that ICR decreases with increasing H₂SO₄ concentrations. The corrosion mechanisms of SS316L in PEMFC cathode environments are analysed and discussions on choosing simulated PEMFC cathode corrosion environments for accelerated tests are also provided.     

High-density plasma nitriding of AISI 316L for bipolar plate in proton exchange membrane fuel cell

Austenitic stainless steel (AISI 316L) is nitrided by inductively coupled plasma using a gas mixture of N₂ and H₂ at temperatures between 530 K and 650 K, and the corrosion resistance as well as the interfacial contact resistance (ICR) are measured in a simulated proton exchange membrane fuel cell (PEMFC) environment.After plasma nitriding, a nitrogen-expanded austenite layer, the so-called S-phase is formed in all nitrided samples. The ICR value of the nitrided samples decreases to approximately 10 mΩcm² after plasma nitriding. The sample nitrided at 590 K shows the best corrosion property, while the corrosion resistance of the sample nitrided at higher temperatures decreases because of the formation of Cr-depleted regions in the nitrided sample. By using high-density plasma, the process temperature can be reduced to such a low temperature that Cr depletion is not significant, but a dense S-phase is formed.     

An investigation into TiN-coated 316L stainless steel as a bipolar plate material for PEM fuel cells

In order to reduce the cost, weight and volume of the bipolar plates, considerable attention is being paid to developing metallic bipolar plates to replace the non-porous graphite bipolar plates that are in current use. However, metals are prone to corrosion in the proton exchange membrane (PEM) fuel cell environments, which decreases the ionic conductivity of the membrane and lowers the overall performance of the fuel cells. In this study, TiN was coated on SS316L using a physical vapor deposition (PVD) technology (plasma enhanced reactive evaporation) to increase the corrosion resistance of the base SS316L. X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods were used to characterize the TiN-coated SS316L. XRD showed that the TiN coating had a face-centered-cubic (fcc) structure. Potentiodynamic tests and electrochemical impedance tests showed that the corrosion resistance of SS316L was significantly increased in 0.5 M H₂SO₄ at 70 °C by coating with TiN. In order to investigate the suitability of these coated materials as cathodes and anodes in a PEMFC, potentiostatic tests were conducted under both simulated cathode and anode conditions. The simulated anode environment was −0.1 V versus SCE purged with H₂ and the simulated cathode environment was 0.6 V versus SCE purged with O₂. In the simulated anode conditions, the corrosion current of TiN-coated SS316L is −4 × 10⁻⁵ A cm⁻², which is lower than that of the uncoated SS316L (about −1 × 10⁻⁶ A cm⁻²). In the simulated cathode conditions, the corrosion current of TiN-coated SS316L is increased to 2.5 × 10⁻⁵ A cm⁻², which is higher than that of the uncoated SS316L (about 5 × 10⁻⁶ A cm⁻²). This is because pitting corrosion had taken place on the TiN-coated specimen.     

Titanium oxynitride films for a bipolar plate of polymer electrolyte membrane fuel cell prepared by inductively coupled plasma assisted reactive sputtering

Titanium oxynitride (TiN_xO_y) films are investigated for application as a bipolar plate coating material in a polymer electrolyte membrane fuel cell (PEMFC). TiN_xO_y films with various amounts of oxygen are deposited on stainless-steel substrates by inductively coupled plasma (ICP) assisted reactive sputtering by changing the oxygen gas flow rate. The interfacial contact resistance (ICR) and the corrosion resistance of the TiN_xO_y films are measured under PEMFC simulated conditions. When the amount of oxygen in the TiN_xO_y film is approximately <12 at.% (O₂ flow rate ≤0.2 sccm), the corrosion resistance is enhanced considerably, whereas the interfacial contact resistance does not change. The corrosion current density decreases from 8 × 10⁻⁶ A cm⁻² for the TiN-coated sample to 2.7 × 10⁻⁶ A cm⁻² at 0.6 V vs. SCE as a result of oxygen incorporation in the TiN film. The ICR value remains at 2.5 mΩ cm² at 150 N cm⁻². When a small amount of oxygen is added to the TiN film, it is postulated that the oxygen atoms locate at the column and grain boundaries, and thus prevent corrosive media from penetrating into the substrate while not deteriorating the electrical property of the film.