High nitrogen stainless steel as bipolar plates for proton exchange membrane fuel cells

To investigate the applicability of high nitrogen (HN) austenitic stainless steel as bipolar plates for proton exchange membrane fuel cells (PEFCs), the polarization tests were carried out in synthetic solutions (0.05 M SO₄²⁻ (pHs 2.3, 4.3 and 5.5) +2 ppm F⁻) at 353 K. Interfacial contact resistance between the stainless steel and gas diffusion layer was measured before and after polarization. A single cell employing the HN stainless steel as bipolar plates was operated for 1000 h at 0.5 A cm⁻² (12.5 A). The single cell exhibited voltage drop of 17 mV during the operation. Corrosion products were scarcely detected for the HN stainless steel bipolar plate, as confirmed by scanning electron microscopy. After the polarization tests and single cell operation, XPS analyses were carried out to examine the resulting surface states. In the synthetic solutions to pH 4.3, the passive films mainly consisted of oxides enriched with Cr. When the solution pH was 5.5, on the other hand, the films were mainly composed of Fe-oxides. After the single cell operation for 1000 h, it was found that the passive films of the rib surface for the gas inlet part was mainly composed by Fe-oxides. On the other hand, the passive films for the ribs from center to gas outlet part were mainly made up of Cr-oxides. By combining the simulated and real operation environments, it is believed that the corrosion resistive Cr-oxides passive layer of the HN stainless steel obtained by the presence of nitrogen incorporated into the stainless steel could contribute to the maintenance of the higher cell voltage during the extensive cell operation.     

Localised corrosion processes of austenitic stainless steel bipolar plates for polymer electrolyte membrane fuel cells

This research addresses the problem of localised corrosion of stainless steel PEMFC bipolar plates. The susceptibility to pitting and crevice corrosion of austenitic AISI 304 stainless steel has been investigated both by post-mortem microscopic analysis of the end-plates of a laboratory single-cell and by studies of electrochemically corroded stainless steels, in the presence of specially-designed crevice-formers simulating the operating conditions of a PEMFC. This work is based on optical and scanning-electron microscopies as well as potentiostatic and potentiodynamic measurements. The crevice-formers we considered were: Teflon, graphite and AISI 304. The samples, coupled to the crevice-formers have been tested in aqueous solutions containing Cl⁻, SO₄²⁻ and F⁻. From the E-log i plot, the values of corrosion, pitting, crevice and protection potential have been obtained and perfect and imperfect passivity conditions have been identified.     

Performance of surface chromizing layer on 316L stainless steel for proton exchange membrane fuel cell bipolar plates

Stainless steels as proton exchange membrane fuel cell bipolar plates have received extensive attention in recent years. The pack chromizing layer was fabricated on 316L stainless steel to improve the corrosion resistance and electrical conductivity. The corrosion properties were investigated in 0.5 M H₂SO₄ + 2 ppm HF solution at 70 °C purged with hydrogen gas and air. Higher electrochemical impedance and more stable passive film were obtained by chromizing the 316L stainless steel. Potentiodynamic polarization results showed the corrosion current densities were reduced to 0.264  μA cm⁻² and 0.222  μA cm⁻² in two simulated operating environments. In addition, the interfacial contact resistance was decreased to 1.4 mΩ⋅cm² under the compaction force of 140 N⋅cm⁻² and maintained at low values after potentiostatic polarization for 4 h. The excellent corrosion and conductive performances could be attributed to the chromium carbides and high alloying element content in chromizing layer.     

Influence of fluoride ions on corrosion performance of 316L stainless steel as bipolar plate material in simulated PEMFC anode environments

Corrosion performance of 316L stainless steel as a bipolar plate material in proton exchange membrane fuel cell (PEMFC) is studied under different simulated PEMFC anode conditions. Solutions of 1 × 10⁻⁵ M H₂SO₄ with a wide range of different F⁻ concentrations at 70 °C bubbled with hydrogen gas are used to simulate the PEMFC anode environments. Electrochemical methods, both potentiodynamic and potentiostatic, are employed to study the corrosion behavior. Scanning electron microscope (SEM) and atomic force microscope (AFM) are used to examine the surface morphology of the specimen after it is potentiostatic polarized in simulated PEMFC anode environments. X-ray photoelectron spectroscopy (XPS) analysis is used to identify the compositions and the depth profile of the passive film formed on the 316L stainless steel surface after it is polarized in simulated PEMFC anode environments. Mott–Schottky measurements are used to characterize the semiconductor passive films. The results of potentiostatic analyses show that corrosion currents increase with F⁻ concentrations. SEM examinations show that no localized corrosion occurs on the surface of 316L stainless steel and AFM measurement results indicate that the surface topography of 316L stainless steel becomes slightly rougher after polarized in solutions with higher concentration of F⁻. From the results of XPS analysis and Mott–Schottky measurements, it is determined that the passive film formed on 316L stainless steel is a single layer n-type semiconductor.     

Deposition of gold–titanium and gold–nickel coatings on electropolished 316L stainless steel bipolar plates for proton exchange membrane fuel cells

The effects of electropolishing and coating deposition on electrical resistance and chemical stability were studied for the stainless steel bipolar plates in proton exchange membrane fuel cell (PEMFC). A series of 316L stainless steel plates, selected as the substrate for a proton exchange membrane fuel cell (PEMFC) bipolar plate, were electropolished with a solution of H₂SO₄ and H₃PO₄ at temperatures ranging from 70 to 110 °C. The surface regions of the two electropolished stainless steel plates were coated with gold and either a titanium or nickel layer using electron beam evaporation. The electropolished stainless steel plates coated in 2-μm thick gold with a 0.1-μm titanium or nickel interlayer showed remarkably smooth and uniform surface morphologies in AFM and FE-SEM images compared to the surfaces of the plates that were coated after mechanical polishing only. The electrical resistance and water contact angle of the deposited stainless steel bipolar plates are strongly dependent on the surface modification treatments (i.e., mechanical polishing versus electropolishing). ICP-MS and XPS results indicate that after electropolishing, the coating layers show excellent chemical stability after exposure to an H₂SO₄ solution of pH 3. Finally, it was concluded that before coating deposition, the surface modification using electropolishing was very suitable for enhancing the electrical property and chemical stability of the stainless steel bipolar plate.     

Corrosion inhibition of methanol towards stainless steel bipolar plate for direct formic acid fuel cell

The corrosion properties of AISI316L stainless steel (316 L SS) as bipolar plates are investigated under aqueous acid methanol solutions (0.05 M H₂SO₄ + 2 ppm HF + 10 M HCOOH + x M CH₃OH (x = 0, 3, 6 and 9) solutions at 70 °C) to simulate the varied anodic operating conditions of direct formic acid fuel cells (DFAFCs). When the methanol content is higher, the potentiodynamic, potentiostatic polarisation and EIS tests of the 316 L SS bipolar plates all show excellent corrosion resistance. The surface morphology and the glow discharge mass spectrometer (GDMS) illustrate that the surface corrosion on 316 L SS bipolar plates is slowed down when the methanol concentration is increased. These results indicate the methanol plays the role in retarding the corrosion rate of the 316 L SS in simulated DFAFCs anodic operating conditions by restricting the proton conductivity in the test solutions. The sample tested in higher content methanol solution has smoother corroded surface and thinner passivation film, which contributes to a lower interfacial contact resistances (ICR) value.     

Applicability of extra low interstitials ferritic stainless steels for bipolar plates of proton exchange membrane fuel cells

Ferritic stainless steels can be attractive bipolar plate materials of proton exchange membrane fuel cells (PEMFC), provided that the stainless steels show sufficient corrosion resistance, for instance, by eliminating interstitial elements such as carbon and nitrogen. In the present study, thus, ferritic stainless steels (19Cr2Mo and 22Cr2Mo) with extra low interstitials (ELI) are evaluated to determine the required level of chromium content to apply them for PEMFC bipolar plates. In a simulated PEMFC environment (0.05 M SO₄²⁻ (pH 3.3) + 2 ppm F⁻ solution at 353 K), the 22Cr2Mo stainless steel showed lower current density during the polarization in comparison with the 19Cr2Mo one. The polarization behavior of the 22Cr2Mo stainless steel resembles that of the type 316 one (17Cr12Ni2Mo). Similar values of interfacial contact resistance (ICR) are observed for both ferritic stainless steels. The 22Cr2Mo stainless steel bipolar plate is found to be stable throughout the cell operation, while the 19Cr2Mo stainless steel corroded within 1000 h. After the cell operation, the 22Cr2Mo stainless steel retains the chromium enriched passive film, while the chromium enriched surface film is not found for the 19Cr2Mo one, showing iron oxide/hydroxide based film. X-ray fluorescence (XRF) analysis of the membrane electrode assemblies (MEAs) after the cell operation indicates that the 22Cr2Mo stainless steel was less contaminated with iron species. The above results suggest that the 22Cr2Mo stainless steel can be applicable to bipolar plates for PEMFC, especially 22 mass% of chromium content in ferritic stainless steel with ELI system is, at least, demanded to ensure stable cell performance.     

Corrosion protection of 304 stainless steel bipolar plates using TiC films produced by high-energy micro-arc alloying process

Metallic bipolar plates look promising for the replacement of graphite due to higher mechanical strength, better durability to shocks and vibration, no gas permeability, acceptable material cost and superior applicability to mass production. However, the corrosion and passivation of metals in environments of proton exchange membrane fuel cell (PEMFC) cause considerable power degradation. Great attempts were conducted to improve the corrosion resistance of metals while keeping low contact resistance. In this paper, a simple, novel and cost-effective high-energy micro-arc alloying process was employed to prepare compact titanium carbide as coatings for the type 304 stainless steel bipolar plates with a metallurgical bonding between the coating and substrate. It was found that TiC coating increased the corrosion potential of the bare steel in 1 M H₂SO₄ solution at room temperature by more than 200 mV, and decreased significantly its corrosion current density from 8.3 μA cm⁻² for the bare steel to 0.034 μA cm⁻² for the TiC-coated steel. No obvious degradation was observed for the TiC coatings after 30-day exposure in solution.     

Molybdenum carbide coated 316L stainless steel for bipolar plates of proton exchange membrane fuel cells

Superior corrosion resistance and high electrical conductivity are crucial to the metallic bipolar plates towards a wider application in proton exchange membrane fuel cells. In this work, molybdenum carbide coatings are deposited in different thicknesses onto the surface of 316 L stainless steel by magnetron sputtering, and their feasibility as bipolar plates is investigated. The microstructure characterization confirms a homogenous, compact and defectless surface for the coatings. The anti-corrosion performance improves with the increase of the coating thickness by careful analysis of the potentiodynamic and potentiostatic data. With the adoption of a thin chromium transition layer and coating of a ∼1052 nm thick molybdenum carbide, an excellent corrosion current density of 0.23 μA cm⁻² is achieved, being approximately 3 orders of magnitude lower than that of the bare stainless steel. The coated samples also show a low interfacial contact resistance down to 6.5 mΩ cm² in contrast to 60 mΩ cm² for the uncoated ones. Additionally, the hydrophobic property of the coatings’ surface is beneficial for the removal of liquid water during fuel cell operation. The results suggest that the molybdenum carbide coated stainless steel is a promising candidate for the bipolar plates.     

Improved polymer electrolyte fuel cell performance with membrane electrode assemblies using modified metallic plate: Comparative study on impact of various coatings

Bipolar plate is one of the key components of polymer electrolyte membrane fuel cell. In the present study, metallic plates are explored as bipolar plates in comparison to most generally used high-density graphite plates. Among various metals, stainless steel 316L is preferred due to its low cost, high strength, ease of machining and for its corrosion resistance characteristics. However, the challenges associated with metallic plates are high interfacial contact resistance due to passive oxide layer formation and possible corrosion product during operation in chemically harsh environments, which may contaminate the membrane electrode assembly. Three electrically conductive and corrosion resistant coatings namely Titanium Nitrides, Plasma Nitride, and Gold have been coated over the surface of stainless steel 316L metallic plate to overcome these challenges and to explore their impact on fuel cell performance using standard membrane electrode assemblies. These coatings are characterized by X-Ray Diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Spectroscopy along with interfacial contact resistance measurements. Further, the coated SS plates have been tested in real time polymer electrolyte membrane fuel cell operation for their use as bipolar plates and their performances have been compared with the fuel cell comprising conventional graphite plates. A cell comprising Titanium Nitride, Gold and Plasma Nitride coated metallic plates exhibit a power density of 430, 720 & 268 mW cm⁻² respectively, at an operating fuel cell potential of 0.6 V. Gold coated metallic plate shows comparable polymer electrolyte membrane fuel cell performance in relation to conventional graphite plate.     

Investigation of sintered stainless steel fiber felt as gas diffusion layer in proton exchange membrane fuel cells

The feasibility of using sintered stainless steel fiber felt (SSSFF) as gas diffusion layer (GDL) in proton exchange membrane fuel cells (PEMFCs) is evaluated in this study. The SSSFF is coated with an amorphous carbon (a-C) film by closed field unbalanced magnetron sputter ion plating (CFUBMSIP) to enhance the corrosion resistance and reduce the contact resistance. The characteristics of treated SSSFF, including microscopic morphology, mechanical properties, electrical conductivity, electrochemical behavior and wettablity characterization, are systematically investigated and summarized according to the requirements of GDL in PEMFC. A membrane electrode assembly (MEA) with a-C coated SSSFF-15 GDL is fabricated and assembled with a-C coated stainless steel bipolar plates in a single cell. The initial peak power density of the single cell is 877.8 mW cm⁻² at a current density of 2324.9 mA cm⁻². Lifetime test of the single cell over 200 h indicates that the a-C coating protects the SSSFF-15 GDL from corrosion and decreases the performance degradation from 30.6% to 6.3%. The results show that the SSSFF GDL, enjoying higher compressive modulus and ductility, is a promising solution to improve fluid permeability of GDL under compression and PEMFC durability.     

Growth of Cr-Nitrides on commercial Ni–Cr and Fe–Cr base alloys to protect PEMFC bipolar plates

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant CrN or Cr₂N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of commercially available, high Cr (30–35 wt%) Ni–Cr alloys and a ferritic high Cr (29 wt%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effects for the Ni–Cr base alloys, but beneficial effects for the stainless steel alloy. Positive results from single-cell fuel cell testing are also presented.     

Improvement of corrosion resistance and electrical conductivity of 304 stainless steel using close field unbalanced magnetron sputtered carbon film

Carbon film has been deposited on 304 stainless steel (SS304) using close field unbalanced magnetron sputter ion plating (CFUBMSIP) to improve the corrosion resistance and electrical conductivity of SS304 acting as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The corrosion resistance, interfacial contact resistance (ICR), surface morphology and contact angle with water of the bare and carbon-coated SS304 are investigated. The carbon-coated SS304 shows good corrosion resistance in the simulated cathode and anode PEMFC environment. The ICR between the carbon-coated SS304 and the carbon paper is 8.28-2.59 mΩ cm² under compaction forces between 75 and 360 N cm⁻². The contact angle of the carbon-coated SS304 with water is 88.6°, which is beneficial to water management in the fuel cell stack. These results indicate that the carbon-coated SS304 exhibits high corrosion resistance, low ICR and hydrophobicity and is a promising candidate for bipolar plates.     

Tantalum nitride coated AISI 316L as bipolar plate for polymer electrolyte membrane fuel cell

Tantalum nitride (TaN) thin films are deposited on AISI 316L stainless steel by inductively coupled, plasma-assisted, reactive magnetron sputtering at various N₂ flow rates. TaN film behavior is investigated in simulated polymer electrolyte membrane fuel cell (PEMFC) conditions by using electrochemical measurement techniques for application as bipolar plates. The results of a potentio-dynamic polarization test under PEMFC cathodic and anodic conditions indicate that the corrosion current density of the TaN_x films is of the order of 10⁻⁷ A cm⁻² (at 0.6 V) and 10⁻⁸ A cm⁻² (at −0.1 V), respectively; these results are considerably better than the individual results for metallic Ta films and AISI 316L stainless steel. The TaN_x films exhibit superior stability in a potentio-static polarization test performed under PEMFC cathodic and anodic conditions. The interfacial contact resistance of the films is measured in the range of 50-150 N cm⁻², and the lowest value is 11 mΩ cm² at a compaction pressure of 150 N cm⁻².     

Effect of manufacturing conditions on the corrosion resistance behavior of metallic bipolar plates in proton exchange membrane fuel cells

Metallic bipolar plates are one of the promising alternatives to the graphite bipolar plates in proton exchange membrane fuel cell (PEMFC) systems. In this study, stainless steel (SS304, SS316L, and SS430), nickel (Ni 270), and titanium (Grade 2 Ti) plates with an initial thickness of 51 μm were experimented as bipolar plate substrate materials in corrosion resistance tests. In addition to unformed blanks, SS316L plates were formed with stamping and hydroforming processes to obtain bipolar plates under different process conditions (stamping force, hydroforming pressure, stamping speed, hydroforming pressure rate). These bipolar plates, then, were subjected to corrosion tests, and the results were presented and discussed in detail. Potentiodynamic polarizations were performed to observe corrosion resistance of metallic bipolar plates by simulating the anodic and cathodic environments in the PEMFC. In order to determine the statistical significance of the corrosion resistance differences between different manufacturing conditions, analysis of variance (ANOVA) technique was used on the corrosion current density (I_corr, μA cm⁻²) values obtained from experiments. ANOVA for the unformed substrate materials indicated that SS430 and Ni have less corrosion resistance than the other substrate materials tested. There was a significant difference between blank (unformed) and stamped SS316L plates only in the anodic environment. Although there was no noteworthy difference between unformed and hydroformed specimens for SS316L material, neither of these materials meet the Department of Energy‘s (DOE) target corrosion rate of ≤1 μA cm⁻² by 2015 without coating. Finally, stamping parameters (i.e. speed and force levels) and hydroforming parameters (i.e. the pressure and pressure rate) significantly affected the corrosion behavior of bipolar plates.     

Corrosion and interfacial contact resistance of nanocrystalline β-Nb2N coating on 430 FSS bipolar plates in the simulated PEMFC anode environment

The corrosion of metallic bipolar plates in the proton exchange membrane fuel cells (PEMFCs) anode environment would degrade the performance and shorten the lifespan of the fuel cell. Hence, it is essential to develop a conductive coating with good corrosion resistance. Herein we demonstrate a dense, defect-free, and well-adhered nanocrystalline β-Nb₂N coating prepared on 430 ferritic stainless steel (430 FSS) via disproportionation of Nb(Ⅳ) species in molten salts. The corrosion mechanism of bare and β-Nb₂N coated 430 FSS in the simulated PEMFC anode environment is also studied by electrochemical techniques including potentiodynamic polarization, potentiostatic polarization, and electrochemical impedance spectroscopy. Results show that β-Nb₂N coating can significantly improve the corrosion resistance of the steel alloy with acceptable contact resistance. In addition, no obvious degradation is observed for the β-Nb₂N coating after potentiostatic polarization measurement for 500 h. This work offers a promising strategy to develop the corrosion protective coating on metallic bipolar plates for PEMFCs.     

Conducting polymer-coated stainless steel bipolar plates for proton exchange membrane fuel cells (PEMFC)

Stainless steel satisfies many of the requirements for proton exchange membrane (PEM) fuel cell bipolar plates except its corrosion under fuel cell operating conditions. Metal oxide formation leads to contact resistance, and metal dissolution can cause contamination of the membrane electrode assembly (MEA). These problems can be solved by coating stainless steel plates with corrosion resistant and conductive layers. In this study, 304 stainless steel was coated electrochemically with the conducting polymers polyaniline (PANI) and polypyrrole (PPY). Cyclic voltammetry was used for the polymerization and deposition of these polymers. The polymer-coated stainless steel plates were tested for corrosion and contact resistance under PEM fuel cell conditions, which showed improved corrosion resistance with acceptable contact resistance.     

Carbon-polymer composite coatings for PEM fuel cell bipolar plates

A carbon-polymer composite coating on stainless steel 316L substrates was investigated for the use as bipolar plate material for polymer electrolyte membrane fuel cells. The coating consisted of 45 vol% graphite, 5 vol% carbon black and 50 vol% epoxy binder. The coating was applied by a spraying technique followed by hot-pressing while the binder cured. An interfacial contact resistance of 9.8 mΩ cm² at a compaction pressure of 125 N cm⁻² was measured. Ex-situ electrochemical tests showed that the carbon-polymer composite coated plates had smaller increases in the interfacial contact resistance after polarization than bare stainless steel plates at potentials of 0.0191 and 0.6191 V_SHE. At 1.0 V_SHE, the resistance increased similarly for both the coated plate and the bare stainless steel plate, and reached unacceptable values. The porosity of the coating was estimated with scanning electron microscope imaging of the cross-section of the coating to be about 50%.     

Anticorrosion properties of Ta-coated 316L stainless steel as bipolar plate material in proton exchange membrane fuel cells

In order to reduce the cost, volume and weight of the bipolar plates used in the proton exchange membrane fuel cells (PEMFC), more attention is being paid to metallic materials, among which 316L stainless steel (SS316L) is quite attractive. In this study, metallic Ta is deposited on SS316L using physical vapor deposition (PVD) to enhance the corrosion resistance of the bipolar plates. Simulative working environment of PEMFC is applied for testing the corrosion property of uncoated and Ta-coated SS316L. X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods (potentiodynamic and potentiostatic polarization) are also used for analyzing characteristics of uncoated and Ta-coated SS316L. Results show that, Ta-coated SS316L has significantly better anticorrosion property than that of uncoated SS316L, with corrosion current densities of uncoated SS316L being 44.61 μA cm⁻² versus 9.25 μA cm⁻² for Ta-coated SS316L, a decrease of about 5 times. Moreover, corrosion current densities of Ta-coated SS316L in both simulative anode (purged with H₂) and cathode (purged with air) conditions are smaller than those of uncoated SS316L.     

Corrosion resistance of CrN film deposited by high-power impulse magnetron sputtering on SS304 in a simulated environment for proton exchange membrane fuel cells

Insufficient corrosion resistance and conductivity are two major problems hindering the wide application of stainless steel (SS) bipolar plates in proton exchange membrane fuel cells. This study explores the use of CrN monolayer and multilayer films to improve the performance of SS304 bipolar plates, which are realized by high-power impulse magnetron sputtering with single pulse width or alternating pulse width. The effect of pulse width on the film structure and composition was characterized by various characterization techniques. Furthermore, corrosion and interfacial contact resistance (ICR) test results show that monolayer CrN film using a single long pulse of 40 μs has the lowest corrosion current density of 0.08 μA/cm² (0.6 V vs. Ag/AgCl) and ICR of 3.15 mΩ cm² in all coated samples. As the pulse width increases, vacancy-like defects in film decrease and the density increases, which is attribute to high bombardment flux and high average power of long pulse during deposition.