Copper oxide catalysts supported on ceria for low-temperature CO oxidation

Copper oxide catalysts supported on ceria were prepared by wet impregnation method using finely CeO₂ nanocrystals, which was derived from alcohothermal synthesis, and copper nitrate dissolved in the distilled water. The catalytic activity of the prepared CeO₂ and CuO/CeO₂ catalysts for low-temperature CO oxidation was investigated by means of a microreactor-GC system. The samples were characterized using BET, XRD, SEM, HRTEM and TPR.     

Low temperature CO oxidation over Au/TiO2 and Au/SiO2 catalysts

After a high-temperature reduction (HTR) at 773 K, TiO₂-supported Au became very active for CO oxidation at 313 K and was an order of magnitude more active than SiO₂-supported Au, whereas a low-temperature reduction (LTR) at 473 K produced a Au/TiO₂ catalyst with very low activity. A HTR step followed by calcination at 673 K and a LTR step gave the most active Au/TiO₂ catalyst of all, which was 100-fold more active at 313 K than a typical 2% Pd/Al₂O₃ catalyst and was stable above 400 K whereas a sharp decrease in activity occurred with the other Au/TiO₂ (HTR) sample. With a feed of 5% CO, 5% O₂ in He, almost 40% of the CO was converted at 313 K and essentially all the CO was oxidized at 413 K over the best Au/TiO₂ catalyst at a space velocity of 333 h^–1 based on CO + O₂. Half the chloride in the Au precursor was retained in the Au/TiO₂ (LTR) sample whereas only 16% was retained in the other three catalysts; this may be one reason for the low activity of the Au/TiO₂ (LTR) sample. The reaction order on O₂ was approximately 0.4 between 310 and 360 K, while that on CO varied from 0.2 to 0.6. The chemistry associated with this high activity is not yet known but is presently attributed to a synergistic interaction between gold and titania.     

The preparation of Au/CeO2 catalysts and their activities for low-temperature CO oxidation

Au/CeO₂ catalysts prepared by co-precipitation (CP) and deposition-precipitation (DP) methods were tested for low temperature CO oxidation reaction. The structural characters and redox features of the catalysts were investigated by XRD, XPS and H₂-TPR. Their catalytic performances for low temperature CO oxidation were studied by means of a microreactor -GC system. It showed that the catalytic activities of Au/CeO₂ catalysts greatly depended on the preparation method. The catalysts prepared by DP method exhibited a surprisingly higher activity towards CO oxidation than that prepared by CP method. This may arise from the differences in the particle sizes of Au and redox properties of the catalysts. The low Au loading and the resistance to high temperature of DP-prepared catalyst made it more applicable.     

CO selective oxidation in hydrogen-rich gas over platinum catalysts

The kinetics of CO oxidation in hydrogen-rich gas on Pt/mordenite (Pt/MD) or Pt/Al₂O₃ were investigated over a wide range of CO (0.4–1.8%) and O₂ concentrations (0.26–1.14%). The integral flow measurements showed that both the catalysts that could remove CO from 1% to ppm-level Pt/MD had a wider operation temperature range than Pt/Al₂O₃, especially towards lower temperatures.     

Isoprene formation from CO and H2 over CeO2 catalysts

The CO-H₂ reaction over CeO₂ catalysts at around 623 K and 67 kPa forms isoprene with about 20% and 70% selectivities in total and C₅ hydrocarbons, respectively. The formation of dienes may be due to the low and high activity of CeO₂ for alkene and CO hydrogenation, respectively.     

Gold supported CeO2/Al2O3 catalysts for CO oxidation: influence of the ceria phase

A series of low loading gold supported ceria/alumina catalysts have been prepared by the deposition–precipitation method, varying the pH of the synthesis. The catalysts were characterised by means of XRD, TEM, S_BET, XRF and UV–Vis techniques, and their catalytic activity towards CO oxidation in the absence and in presence of water in the stream, were tested. It has been found that in this low loading gold catalysts, where the metallic particles are far away one from another and the oxygen transportation is not the limiting step of the reaction, the electronic properties of the ceria phase and the structure of the metal-support perimeter more than the diameter of the gold nanoparticles is the determinant factor in the catalytic performances of the solid.     

Low-temperature catalytic combustion of methanol and its decomposed derivatives over supported gold catalysts

Gold can be compared favorably with Pd and Pt in the catalytic combustion of CH₃OH, HCHO and HCOOH when it is deposited on some reducible metal oxides (-Fe₂O₃, TiO₂, etc.). While the supported gold catalysts are less active in H₂ oxidation, they exhibit much higher activities in CO oxidation. For Au/TiO₂, the effect of catalyst preparation was further investigated. Since the activity for CO oxidation of the gold catalysts is not depressed but enhanced by moisture, they are practically applicable to CO removal from air at room temperature. Gold supported on manganese oxide is especially effective in the selective CO removal from hydrogen, indicating its potential applicability to polymer electrolyte fuel cells using the reformed gas of methanol.     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Partial oxidation of methane over ruthenium catalysts

The catalytic partial oxidation of methane with oxygen to produce synthesis gas was studied under a wide range of conditions over supported ruthenium catalysts. The microreador results demonstrated the high activity of ruthenium catalysts for this reaction. A catalyst having as little as 0.015% (w/w) Ru on Al₂O₃ gave a higher synthesis gas selectivity than a catalyst having 5% Ni on SiO₂. XANES measurements for fresh and used catalyst samples confirmed that ruthenium is reduced from ruthenium dioxide to ruthenium metal early during the experiments. Ruthenium metal is thus the active element for the methane partial oxidation reaction.     

High catalytic activity of PdOx/MnO2 for CO oxidation and importance of oxidation state of Mn

PdO_x/MnO₂ has been examined as a catalyst for CO oxidation using a conventional flow reactor at reaction temperatures between 50 and 150°C. In the reaction conditions of GHSV (gashourlyspacevelocity) of 1.22 × 10⁵/h and CO concentration of 2000 ppm, PdO_x/MnO₂ showed higher catalytic activity compared with PdO_x/Mn₂O₃, which had been previously reported as an effective catalyst due to the cooperative action of Pd and Mn₂O₃ for this reaction. The reason for higher activity of PdO_x/MnO₂ than PdO_x/Mn₂O₃ has been investigated using TPR (temperatureprogrammed reduction) and XPS studies. TPR showed that PdO_x/MnO₂ could be reduced by CO at much lower temperature than PdO_x/Mn₂O₃. During the experiment of reduction and oxidation, XPS showed that the valence of Mn in the PdO_x/MnO₂ was between 4+ and 3+, which is higher than that of Mn in the PdO_x/Mn₂O₃ catalyst of which the valence has been reported to be between 3+ and 2+. It is known that in this catalyst system the support supplies oxygen onto Pd, where the oxidation occurs with adsorbed CO, and the ability of the support to provide oxygen improves the performance of the catalyst. Therefore, it was concluded that the readiness of MnO₂ to be reduced with maintaining a higher oxidation state showed higher CO oxidation activity than Mn₂O₃ as support for PdO_x.     

Nanodispersed Au/Al2O3 catalysts for low-temperature CO oxidation: Results of research activity at the Boreskov Institute of Catalysis

This paper presents some important results of the studies on preparation and catalytic properties of nanodispersed Au/Al₂O₃ catalysts for low-temperature CO oxidation, which are carried out at the Boreskov Institute of Catalysis (BIC) starting from 2001. The catalysts with a gold loading of 1–2 wt.% were prepared via deposition of Au complexes onto different aluminas by means of various techniques (“deposition-precipitation” (DP), incipient wetness, “chemical liquid-phase grafting” (CLPG), chemical vapor deposition (CVD)). These catalysts have been characterized comparatively by a number of physical methods (XRD, TEM, diffuse reflectance UV/vis and XPS) and catalytically tested for combustion of CO impurity (1%) in wet air stream at near-ambient temperature. Using the hydroxide or chloride gold complexes capable of chemical interaction with the surface groups of alumina as the catalyst precursors (DP and incipient wetness techniques, respectively) produces the catalysts that contain metallic Au particles mainly of 2–4 nm in diameter, uniformly distributed between the external and internal surfaces of the support granules together with the surface “ionic” Au oxide species. Application of organogold precursors gives the supported Au catalysts of egg shell type which are either close by mean Au particle size to what we obtain by DP and incipient wetness techniques (CVD of (CH₃)₂Au(acac) vapor on highly dehydrated Al₂O₃ in a rotating reactor under static conditions) or contain Au crystallites of no less than 7 nm in size (CLPG method). Regardless of deposition technique, only the Cl-free Au/Al₂O₃ catalysts containing the small Au particles (d_i ≤ 5 nm) reveal the high catalytic activity toward CO oxidation under near-ambient conditions, the catalyst stability being provided by adding the water vapor into the reaction feed. The results of testing of the nanodispersed Au/Al₂O₃ catalysts under conditions which simulate in part removal of CO from ambient air or diesel exhaust are discussed in comparison with the data obtained for the commercial Pd and Pt catalysts under the same conditions.     

Low-temperature mild partial oxidation of ethanol over supported platinum catalysts

Supported platinum catalysts containing 1.2% Pt loaded on Al₂O₃ (1.2% Pt/Al₂O₃) and 1.9% Pt loaded on ZrO₂ (1.9% Pt/ZrO₂) were prepared by incipient wetness impregnation and sol–gel method, respectively. The activity of these catalysts in the partial oxidation of ethanol (POE) was examined in a fixed-bed reactor in a temperature range between 373 and 473 K. The results indicated that significant ethanol conversion (C_EtOH > 50%) was found at the low reaction temperature with a feed ratio of O₂/EtOH ratio >0.75. Oxygen molecules introduced in reactant were completely consumed in POE reactions performed. H₂, H₂O, CO and CO₂ were the major products detected. The selectivity of hydrogen (S_H2) and CO (S_CO) varied significantly with reaction conditions. High selectivity of hydrogen (S_H2 > 95%) and low selectivity of CO (S_CO  0%) were found from a mild oxidation at T_R = 373 K over Pt/ZrO₂. However, these two selectivities were drastically deteriorated through oxidation at high T_R, high O₂/EtOH ratio or over Pt/Al₂O₃ catalyst.     

Low-cost nanostructured Fe2O3-based composite catalysts synthesized by mechanical milling for CO oxidation reaction

In this work, the catalytic properties of low-cost nanostructured iron oxide have been improved by the mechanical milling method through combination with copper and cobalt oxide. Synthesized catalysts were characterized by X-ray diffraction, transition electron microscopy, and Brunauer–Emmet–Teller techniques. Also, the catalytic activity and stability of the powders for CO oxidation reaction were investigated. Results indicated that the catalytic activity of the powders has significantly improved after mechanical milling. Minimum complete conversion temperatures for Co–Fe and Cu–Fe composite oxide catalysts were around 245 and 275°C, respectively. No decline in the activity of the catalysts was observed during the long-term stability test. Furthermore, catalytic activity of the composite powders, especially Co–Fe improves at subsequent cycles. In general, cycle durability, stability at high temperature and reaction rate of the iron oxide powder has been improved using it as Cu–Fe and Co–Fe oxide composites.     

CO oxidation over Au/TiO2 prepared from metal-organic gold complexes

A series of Au/TiO₂ catalysts has been prepared from precursors of various metal-organic gold complexes (Au _n , n = 2–4) and their catalytic activity for CO oxidation studied. The Au/TiO₂ catalyst synthesized from a tetranuclear gold complex shows the best performance for CO oxidation with transmission electron microscopy of this catalyst indicating an average gold particle size of 3.1 nm.     

Effect of the support on the mechanism of partial oxidation of methane on platinum catalysts

The partial oxidation of methane was studied on Pt/Al₂O₃, Pt/ZrO₂, Pt/CeO₂ and Pt/Y₂O₃ catalysts. For Pt/Al₂O₃, Pt/ZrO₂ and Pt/CeO₂, temperature programmed surface reaction (TPSR) studies showed partial oxidation of methane comprehends two steps: combustion of methane followed by CO₂, and steam reforming of unreacted methane, while for Pt/Y₂O₃ a direct mechanism was observed. Oxygen Storage Capacity (OSC) evaluated the reducibility and oxygen transfer capacity of the catalysts. Pt/CeO₂ catalyst showed the highest stability on partial oxidation. The results were explained by the higher reducibility and oxygen storage/release capacity which allowed a continuous removal of carbonaceous deposits from the active sites, favoring the stability of the catalyst, For Pt/Al₂O₃ and Pt/ZrO₂ catalysts the increase of carbon deposits around or near the metal particle inhibits the CO₂ dissociation on CO₂ reforming of methane. Pt/Y₂O₃ was active and stable for partial oxidation of methane, and its behavior was explained by a change in the reaction mechanism.     

Effect of chlorine on Ir/CeO2 catalyst behavior for preferential CO oxidation

Effect of chlorine on Ir/CeO₂ catalyst behavior for preferential CO oxidation is investigated by high-resolution transmission electron microscopy, X-ray photoemission spectroscopy, and diffuse reflectance infrared spectroscopy. The presence of chlorine favors the dispersion of Ir particles. On ceria support, the replacement of the lattice oxygen by chloride ions would produce CeOCl species, which could hinder the formation of hydroxyl groups and carbonate and/or carboxylate species on the ceria surface. These features could explain the decreased activity of the Cl-containing Ir/CeO₂ sample.     

Low-temperature water-gas shift reaction on Au/CeO2 catalysts – the influence of catalyst pre-treatment on the activity and deactivation in idealized reformate

The effect of the pre-treatment temperature and atmosphere on the surface composition and on the activity and stability of well defined Au/CeO₂ catalysts in the low-temperature water-gas shift reaction in dilute water gas was investigated by X-ray photoelectron spectroscopy, kinetic measurements and in-situ IR spectroscopic (DRIFTS) measurements, comparing different reductive and oxidative conditioning procedures. Reductive conditioning at 200 °C yields the most active catalyst. Physical origin and consequences of the resulting differences in the reaction behavior are discussed.     

Comparison of CuO/Ce0.8Zr0.2O2 and CuO/CeO2 Catalysts for Low-temperature CO Oxidation

CuO/Ce_0.8Zr_0.2O₂ and CuO/CeO₂ catalysts were prepared via a impregnation method characterized by using FT-Raman, XRD, XPS and H₂-TPR technologies. The catalytic activity of the samples for low-temperature CO oxidation was investigated by means of a microreactor-GC system. The influence of the calcination temperature and different supports on the catalytic activity was studied.     

Kinetic modeling of CO oxidation on Pt/CeO2 in a gradientless reactor

Cerium oxide is a major additive in three-way catalysts used in emission control of automobile exhaust. Pt/CeO₂ was studied in order to better understand the role of ceria in promoting CO oxidation reaction. The kinetics of carbon monoxide oxidation on Pt/cerium oxide catalyst, was studied over the temperature range 100–170°C. Steady state kinetic measurements of CO oxidation were obtained in a computer controlled micro-CSTR reactor. Activation energies were reported to vary between 39·5 and 51·2 kJ mol⁻¹. At low concentrations of either reactant (CO, O₂) and total conversion, the catalyst exhibited multiple steady states, similar to the multiplicity behavior of Pt/Al₂O₃. The total conversion was reached at 120°C. In comparison, the total conversion at low reactant concentrations was reached at a temperature of 148°C for the alumina-supported catalyst. Langmuir–Hinshelwood mechanisms gave a good fit to the data. However, no single rate expression could effectively describe the CO oxidation data over the whole concentration in the product of the CSTR reactor. The facts gathered indicate that oxygen adsorbed on interfacial Pt/Ce sites and ceria lattice oxygen provides oxygen for CO oxidation. Cerium oxide has been found to lower CO oxidation activation energy, enhance reaction activity and tends to suppress the usual CO inhibition effect.     

Poisoning of Pt/C catalysts by CO and its consequences over the kinetics of hydrogen chemisorption

The initial rate of hydrogen dissociation was studied as a function of irreversible CO coverage at 353 K on 30 wt.% Pt/carbon catalysts (Pt/C) prepared according to different processes. The Pt/C catalysts exhibit similar Pt dispersion (D  0.07) and mean Pt particles size (dp  16 nm). The turnover frequency (number of hydrogen molecules dissociated per CO-free surface Pt atom) was determined as a function of CO coverage from 0.0 to 0.8. The evolution of TOF as a function of CO coverage is in agreement with the model of CO adsorbing on low coordination sites (edges, corners) and then spreading across the faces to grow islands as Brandt suggested in the past (R.K. Brandt, M.R. Hughes, L.P. Bourget, K. Truszkowska, R.G. Greenler, Surf. Sci. 286 (1993) 15–25). At high CO coverage (0.8), TOF depends on the process by which the Pt/C catalyst was prepared. In particular, a Pt/C elaborated according to a colloidal process exhibits a low sensitivity to CO poisoning with an increase of TOF by one order of magnitude.