尼龙6/环氧树脂共混体系化学流变行为研究

利用转矩流变仪和应力流变仪对尼龙6/环氧树脂体系的化学流变行为进行了研究。结果表明:在热和剪切力的作用下,环氧树脂与PA6发生了化学微交联反应,使共混体系的转矩和熔体温度上升。研究了环氧树脂含量、转速和温度对共混体系的影响。反应共混物熔体呈假塑性流体特征。随着环氧树脂含量的增加,共混物熔体的复数粘度和储能模量上升。     

ABS/PC共混物的转矩及毛细管流变行为

采用转矩流变仪和毛细管流变仪研究了丙烯腈-丁二烯-苯乙烯(ABS)/聚碳酸酯(PC)共混体系的流变行为,研究共混物组成对熔体流变行为的影响.结果表明:转矩流变仪中,平衡温度随着转速提高而增大,平衡转矩会在某一转速下达到峰值.两种测试方法得到的流变数据基本一致,共混物熔体呈现剪切变稀的假塑性流体特性.随着PC含量的增加,共混物的表现黏度逐渐增大,共混物熔体的非牛顿指数表现为负偏差,黏流活化能则表现出正负偏差,说明ABS与PC间具有一定的相容性.     

ADR对PLA/PBAT共混物流变性能的影响

通过转矩流变仪制备ADR/聚乳酸(PLA)/己二酸丁二醇酯-对苯二甲酸丁二醇酯共聚物(PBAT)共混物,利用转矩流变仪和毛细管流变仪研究了ADR含量对PLA/PBAT流变性能的影响。结果表明:ADR的扩链作用抑制了共混过程中PLA的降解,使体系转矩增大。当ADR添加量达到0.3%时,体系的转矩最平稳。通过毛细管流变仪分析发现共混体系遵守幂律方程,熔体呈现剪切变稀现象;随着ADR含量的增多,共混物非牛顿指数n减小,黏流活化能Eη变大。     

熔融共混法丁腈橡胶/聚酰胺6复合材料的性能研究

为了考察丁腈橡胶(NBR)与聚酰胺6(PA6)共混产物综合性能变化,本文采用不同种类NBR与PA6熔融共混,考察共混过程中转矩值变化,表征了共混物的力学性能、耐溶剂性能,并且共混产物进行了红外光谱分析。研究结果表明:随着共混物体系中橡胶相含量的增加,共混物体系的熔体粘度上升。相同腈基含量下的NBR/PA6共混物的平衡转矩值随着NBR含量的增加而增加;拉伸强度随着共混物中NBR橡胶含量的上升,呈下降趋势。在相同的NBR含量条件下,拉伸强度随着腈基含量的增加而增加;红外测试结果显示NBR与PA间在高温高剪切作用下存在微化学反应,即双键与胺基间的反应;共混物体系中随着NBR含量的上升,共混物体系的体积溶胀率与质量溶胀率均呈上升趋势。     

相容共混物熔体的平衡转矩与组成关系的探讨

以熔体指数不同的高密度聚乙烯(HDPE)和均聚聚丙烯(PP)为试样,利用MiniLab微型混合流变仪,研究了在熔融状态下完全互容的HDPE/HDPE、PP/PP和HDPE/PP共混物熔体的平衡转矩随组成的变化规律。结果表明:相容共混体系的熔体平衡转矩-组成关系曲线一般表现为线性或者二次抛物曲线。当高分子链的化学结构单元不同时,其共混熔体的平衡转矩-组成关系多为二次抛物曲线。     

尼龙6/环氧树脂共混物流变性能的研究

用毛细管流变仪研究了尼龙6／环氧树脂共混物的流变性能。结果表明,在实验范围内共混物熔体为假塑性流体;随着环氧树脂用量的增加,表观粘度（ηa）增大,非牛顿指数（n）减小,熔体稠度（K）增大,粘流活化能降低。     

AS／CPE共混物的流变性能研究

制备了AS/CPE共混物,用毛细管流变仪研究了其流变性能。实验结果表明:AS/CPE共混物熔体呈假塑性,其表观剪切粘度随剪切速率的增大或温度的升高而下降,随共混物中CPE含量的升高而上升。并讨论了CPE对共混物非牛顿指数的影响。     

POM/ACR共混物的加工流变性能研究

将聚甲醛(POM)与丙烯酸酯类弹性体(ACR)在转矩流变仪中密炼共混15 min,研究了POM/ACR共混物的加工流变性能。结果表明,随ACR用量的增加,共混物熔体流动速率和最大转矩降低,平衡转矩提高,且塑化时间稍有延长。对于ACR质量分数为16%的共混物,密炼试验表明密炼温度和转速的升高对其平衡转矩、塑化时间及物料温度均有影响,但转速的影响更为突出。在相同的转速下,随着密炼温度的升高,平衡转矩变小、塑化时间缩短而物料温度上升的幅度变大;在同一密炼温度下,随着转速的提高,平衡转矩总体上增大,塑化时间明显变短,物料温度上升的幅度明显变大。转速70~100 r/min、密炼温度175℃是POM/ACR共混物较为合适的加工条件。     

聚丙烯／无规共聚聚丙烯共混物的流变行为与力学性能研究

以毛细管流变仪研究了聚丙烯(PP)／无规共聚聚丙烯(PP-R)共混物熔体的流变行为。讨论了共混物的组成、剪切应力和剪切速率以及温度对熔体流变行为、熔体粘度的影响。测定了不同配比共混物熔体的非牛顿指数和膨胀比。结果表明：PP／PP-R共混物熔体属假塑性流体，其熔体粘度随PP-R含量的增加而迅速增大。力学性能测试结果表明，PP-R对PP有很好的增韧改性作用。另外，也用偏光显微镜研究了PP-R对共混物结晶形态的影响。     

PVC/M-80共混体系的流变性能研究

本文采用高压毛细管流变仪及HAKKE转矩流变仪对PVC/M-80共混体系的流变性能进行了研究。探讨了原料组分比,以及加工工艺参数对PVC/M-80共混体系流变性能的影响。结果表明,PVC/M-80共混体系熔体是典型的非牛顿假塑性流体;随着M-80组分比的增加,共混体系熔体的平衡扭矩和熔体温度均呈明显的降低趋势;共混体系熔体的平衡扭矩随加工温度的增加呈线性降低;在常用加工转速范围内,转速对共混体系流动性的影响不明显。     

耐油性PA6/NBR共混物的制备与性能研究

采用不同种类的丁腈橡胶(NBR)与聚酰胺6(PA6)熔融共混制备了聚酰胺6/丁腈橡胶混合物(PA6/NBR),考察了共混过程中转矩值的变化,并研究了不同腈基含量共混物的拉伸性能及耐溶剂性能。结果表明,随着橡胶相含量的增加,共混物的熔体黏度、体积溶胀率与质量溶胀率均显著提高,但拉伸强度下降。红外光谱分析表面NBR与PA6在高温高剪切作用下存在微化学反应,并且随腈基含量的增加,PA6/NBR共混物的平衡转矩值增大,拉伸强度明显提高,耐溶剂性下降。     

PVC/环氧树脂E51共混物性能的研究

以504及554/504分别作为固化剂,采用锥形双螺杆挤出机实现了PVC与环氧树脂的熔融共混,制备了PVC/环氧树脂E51共混物。固化剂用量为环氧树脂E51用量的80%时,研究了环氧树脂E51用量、固化剂组成及固化时间对PVC/环氧树脂E51共混物力学性能及维卡软化温度的影响。结果表明:以504及554/504为固化剂,少量环氧树脂E51(4份以内)加入PVC后,有助于提高共混物的拉伸强度、弯曲强度;当环氧树脂E51为2份、固化时间为8h时,共混物维卡软化温度达到最大值100.2℃,比纯PVC高出16.5℃。     

Melt rheological properties of reactive compatibilized HDPE/PET blends

Melt rheological properties of high density polyethylene and poly(ethylene terephthalate) (HDPE/PET) blends compatibilized by an ethylene–butyl acrylate–glycidyl methacrylate terpolymer (EBAGMA) were studied by means of a HAAKE torque rheometer and a capillary rheometer. The phase morphology of the blends was evaluated by a scanning electron microscope (SEM). The results showed that the melts of blends behave pseudoplasticity. The addition of EBAGMA strengthens the interfacial adhesion between HDPE and PET and improves the phase dispersion due to reactive compatibilization. It was observed that the balance torque, melt viscosity, and sensitivity of melt viscosity to shear rate of the melts increase with increasing content of EBAGMA, but the melt flow index and activation energy decrease. At the same time, the plasticizing time is shortened indicating that the processability of the compatibilized blends has been improved. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

动态交联PP/EVA共混物的制备与性能研究

本文将动态交联技术应用于PP/EVA共混体系中,制得动态交联PP/EVA共混物。采用Hakke转矩流变仪研究了动态交联对PP/EVA共混物扭矩的影响;研究了DCP和EVA含量对共混物力学性能的影响;考察了动态交联共混物的维卡软化点。结果表明：加入DCP后,PP/EVA共混物扭矩先升后降,DCP的添加量为EVA含量的1%为宜。随EVA用量的增加,动态交联EVA/PP共混物的冲击强度大幅提高,但拉伸强度有所降低。少量经动态交联的EVA颗粒可以促进共混物中PP的结晶, 提高共混物的维卡软化点。     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

高熔体强度聚丙烯/低密度聚乙烯共混体系的挤出发泡行为研究

利用熔体流动速率测试仪和转矩流变仪对不同比例的高熔体强度聚丙烯(HMSPP)/低密度聚乙烯(PELD)共混体系的流变行为进行研究,并对共混体系的流变数据进行分析.随后采用超临界CO2作为发泡剂进行了HMSPP/PE-LD共混体系的挤出发泡研究,并通过真密度计和扫描电子显微镜表征了发泡材料的表观密度和泡体结构参数.结果表...     

Melt flow behavior of blends from poly(vinyl chloride) and epoxidized natural rubber

Blends from poly(vinyl chloride) (PVC) and epoxidized natural rubber (ENR) were prepared in a Brabender plasticorder by the melt blending technique. The melt flow behavior of these blends with respect to blend ratio and temperature has been examined using a melt flow indexer and capillary rheometer. ENR decreases the Brabender torque, increases the melt flow index (MFI), and decreases the melt viscosity of PVC in the blends. Arrhenius plots were used to study the effect of temperature on melt flow index (MFI) and viscosity. Moreover, the flow behavior index (n′) obtained from capillary rheometer data was found to be dependent on temperature and blend ratio.