添加铜网对片层石墨/Al复合材料热物理性能的影响

使用盐浴法对片层石墨（GFs）进行表面镀Si处理,采用真空热压法制备片层石墨/Al复合材料（Si-GFs/Al）。向Si-GFs/Al复合材料中添加10vol%的铜网,研究了铜网对Si-GFs/Al复合材料热导率和力学性能的影响。使用SEM、聚焦离子束（FIB）和TEM对Si-GFs/Al复合材料的微观结构和微观界面进行表征,并分析了复合材料的断裂机制。结果表明,添加铜网使Si-GFs/Al复合材料内部出现了高聚集定向GFs带,形成高导热通道。当GFs体积分数为30vol%~40vol%时,Si-GFs/Al复合材料的热导率提升了约20%,弯曲强度提升了40%以上。当GFs体积分数为40vol%时,Si-GFs/Al复合材料热导率和弯曲强度同时达到一个优值,分别为512 W/（mK）和127 MPa。      

石墨表面TiC涂层对高定向石墨/Cu复合材料热导率和抗弯强度的影响

以高温盐浴法对天然鳞片石墨粉体(GF)进行表面TiC镀层处理,然后采用真空热压烧结法制备TiCGF/Cu复合材料,研究了粉体表面涂层和GF体积分数对复合材料微观结构、热导率及抗弯强度的影响。系列测试结果表明:随着GF体积分数的降低以及粉体表面TiC镀层的形成,TiC-GF/Cu复合材料平行于GF片层方向的热导率有所降低,抗弯强度有所提升。其中在GF的体积分数占TiC-GF/Cu复合材料70%时,这种变化最为明显,平行于GF片层方向的TiC-GF/Cu复合材料热导率下降幅度最大,从676W/(m·K)下降到526 W/(m·K)。同时,TiC-GF/Cu复合材料的微观结构进一步说明,GF表面的TiC涂层对GF/Cu复合材料的断裂模型起着重要的作用。     

石墨表面镀Si对石墨/Al复合材料热物理性能的影响

研究了石墨粒径及表面镀Si处理对石墨/Al复合材料热物理性能的影响。结果表明:在盐浴过程中石墨表面形成了SiC层,这不仅增强了石墨-Si/Al复合材料的界面结合力,而且抑制了Al4C3相的产生。随着石墨鳞片体积分数从50%增加到70%,复合材料X-Y方向的热导率从492 W/(m·K)增加到654 W/(m·K),而且体积分数为50%的镀Si石墨/Al复合材料抗弯强度达到了81 MPa,相比未镀覆的提高了53%,是理想的定向导热电子封装材料。随着石墨粒径从500μm减小到150μm,石墨-Si/Al复合材料X-Y面方向的热导率由654 W/(m·K)降低到445 W/(m·K),但Z方向的热导率和复合材料抗弯强度变化不明显。     

(SiCP/Cu)-铜箔叠层复合材料的制备与组织性能

采用浸涂法和热压烧结法制备了（SiC_P/Cu）-铜箔叠层复合材料,研究了SiC_P含量对材料组织结构、拉伸性能和断裂韧性的影响。结果表明,制备的（SiC_P/Cu）-铜箔叠层复合材料层间厚度均匀,界面结合力良好,增强颗粒SiC能够弥散分布于黏结相中和界面处。随着SiC_P体积分数的增加,（SiC_P/Cu）-铜箔叠层复合材料的抗拉强度和屈服强度都先增加后降低,当SiC_P的体积分数为20vol%（总体积为100）时,其抗拉强度和屈服强度达到最大值,分别为226.5 MPa和113.1 MPa,断裂方式主要为韧性断裂和部分脆性解理断裂。裂纹扩展方向平行于层界面时,材料的断裂韧性随SiC_P体积分数的增加略有减小,SiC_P体积分数为15%时达到最大值16.96 MPa·m^1/2;裂纹扩展方向垂直于层界面时,（SiC_P/Cu）-铜箔叠层复合材料的断裂韧性随SiC_P体积分数的增加逐渐减小,SiC_P体积分数为15%时达到最大值12.51 MPa·m^1/2。     

压力浸渗制备石墨/铝复合材料及其热学性能

采用压力浸渗法制备了石墨/铝复合材料,研究了不同体积分数鳞片石墨对复合材料热学性能和组织的影响。结果表明,加入石墨片明显提高复合材料水平热导率,同时降低复合材料热膨胀系数和密度。当复合材料中石墨体积分数从23.9%增加到73.4%,复合材料水平热导率从234 W/(m·K)提高到402 W/(m·K),同时热膨胀系数降低至5×10-6/K,兼顾高热导率和低热膨胀系数的特点。     

添加微量Ti 元素对Diamond/Cu复合材料组织及性能的影响

分别采用在Cu基体添加0. 1 wt%的Ti 元素形成Cu₂Ti合金和在Diamond 颗粒表面镀钛(DiamondTi) 的方法, 制备了含Diamond 体积分数为60 %的Diamond/Cu₂Ti 复合材料和DiamondTi/Cu 复合材料。对比分析了Ti 元素对复合材料微观组织、界面结合及性能的影响规律。结果表明: 添加0. 1 wt%Ti 元素能改善Diamond与Cu 的界面结合, 在界面处观察到明显的碳化物反应层; 且以Cu₂Ti合金的方式添加Ti 元素改善界面的效果优于在Diamond 颗粒表面镀Ti 的方式。所制备的Diamond/Cu₂Ti 复合材料的热导率为621 W(m·K) - 1, 而DiamondTi/Cu复合材料的热导率仅为403. 5 W(m·K) -1, 但均高于未添加Ti 制备的Diamond/Cu 复合材料。      

一种新的β-锂霞石增强铜基复合材料热性能

采用热压烧结工艺成功制备了一种新的β-锂霞石增强铜基复合材料.利用扫描电镜和透射电镜对复合材料的微观组织进行了分析,并对不同体积分数复合材料的致密性,热膨胀性能和热传导性能进行了测试.结果表明:β-锂霞石颗粒在铜基体中分布均匀,界面清晰,不发生界面反应;体积分数对复合材料致密性、热膨胀系数和热导率有明显影响,当β-锂霞石颗粒体积分数超过40%时,复合材料的致密性有明显下降,热膨胀系数在(9～15.4)×10-6/K,同时热导率在50～170W/m·K.     

碳纳米管增强镁基复合材料导热性能研究

镁及其合金是目前最轻的金属结构材料,合金化虽然提升了镁合金的力学性能,但导致其导热性能严重下降,限制了镁合金的应用。碳纳米管(CNTs)因具有优异的力学、热学等性能,是最理想的增强体之一,可以用于改善镁合金的力学性能和热学性能。采用粉末冶金法分别以纯Mg、Mg-9Al合金、Mg-6Zn合金为基体制备了不同CNTs含量的镁基复合材料,利用光学显微镜、扫描电子显微镜、透射电子显微镜对复合材料微观组织、基体与增强体界面及析出相进行表征,并对复合材料的拉伸性能和热学性能进行测试。研究结果表明,当CNTs质量分数不超过1.0%时,可提高纯镁基复合材料的导热性能,力学性能仅有稍微降低;将CNTs添加到Mg-9Al合金中,可以促进纳米尺度β-Mg 17 Al 12相在CNTs周围析出,降低了Al在Mg基体中的固溶度,使CNTs/Mg-9Al复合材料的导热性能有所提高。此外,在CNTs/Mg-6Zn复合材料界面处存在C原子和Mg原子的相互嵌入区,这种嵌入型界面不仅有利于复合材料力学性能的提高,也使CNTs起到加速电子移动的“桥”的作用,有利于该复合材料热导率的提高。当CNTs质量分数为0.6%时,CNTs/Mg-6Zn复合材料具有较为优异的热学性能和力学性能,其热导率为127.0 W/(m·K),抗拉强度为303.0 MPa,屈服强度为204.0 MPa,伸长率为5.0%。     

石墨鳞片-碳纤维协同增强铜基复合材料的制备与热物理性能

采用真空热压技术制备了石墨鳞片-碳纤维协同增强铜基复合材料,研究了碳纤维含量对复合材料的组织结构、抗弯强度与热导率的影响.结果表明,石墨鳞片-碳纤维/铜基复合材料界面结合良好;当碳纤维体积分数为0.5vol％～1.5vol％时,碳纤维能够均匀分散在基体中,并有效提升复合材料的抗弯强度.当碳纤维体积分数为1.5vol％时...     

Cu/碳石墨机械密封复合材料的制备与性能

以石墨、高碳、铜粉为原料,酚醛树脂为粘结剂,经机械混捏、冷压成型、加热固化制备Cu/碳石墨机械密封复合材料。研究了铜粉含量、成型压力对Cu/碳石墨复合材料微观组织、体积密度、肖氏硬度的影响。并利用HT-600高温摩擦磨损试验机测试了Cu/碳石墨复合材料的摩擦磨损性能,借助金相显微镜观察其磨损形貌。结果表明:随着铜粉含量的增加,成型压力的增大,复合材料的体积密度、肖氏硬度逐渐提高,摩擦系数逐渐减小。当铜粉含量为25%、成型压力为15MPa时,体积密度达到1.92g/cm3,肖氏硬度达到90.0HS,摩擦系数最小为0.17,材料的综合性能最佳。     

高定向石墨/铜复合材料的制备和热物理性能

为了制备出具有优良热物理性能的石墨/铜复合材料,采用流延法将天然鳞片石墨定向排列在铜箔表面,并使用真空热压法制备具有层状结构的高定向石墨/铜复合材料。使用XRD和SEM等表征方法分析样品的微观形貌和成分,结果表明,在高温的作用下,流延所使用的溶剂充分挥发,热压后石墨仍高定向排列在相邻的两层铜箔之间,并相互搭接;部分熔化的铜在压力作用下渗透到石墨层的孔隙处,铜层之间相互贯穿。这种结构使石墨/铜复合材料具有优良的热物理性能。当石墨体积分数为20vol%~70vol%时,石墨/铜复合材料在高导热平面内热导率高达402~743 W/(m·K),抗弯强度达到126~48 MPa。深入讨论了石墨/铜复合材料的热传导机制,并建立了导热预测模型。      

A comparative study of the coated filler method and the admixture method of powder metallurgy for making metal–matrix composites

Copper–matrix composites were made by powder metallurgy (PM). The reinforcements were molybdenum particles, silicon carbide whiskers and titanium diboride platelets. The coated filler method, which involves a reinforcement coated with the matrix metal, was used. In contrast, conventional PM uses the admixture method, which involves a mixture of matrix powder and reinforcement. For all the composite systems, the coated filler method was found to be superior to the admixture method in providing composites with lower porosity, greater hardness, higher compressive yield strength, lower coefficient of thermal expansion (CTE), higher thermal conductivity and lower electrical resistivity, though the degree of superiority was greater for high than low reinforcement contents. In the coated filler method, the coating on the reinforcement separated reinforcement units from one another and provided a cleaner interface and stronger bond between reinforcement and matrix than the admixture method could provide. The highest reinforcement content attained in dense composites (<5% porosity) made by the coated filler method was 70 vol% Mo, 60 vol% TiB2 and 54 vol% SiC. The critical reinforcement volume fraction above which the porosity of composites made by the admixture method increases abruptly is 60% Mo, 42% TiB2 and 33% SiC. This fraction increases with decreasing aspect ratio of the reinforcement. Among Cu/Mo, Cu/TiB2 and Cu/SiC at the same reinforcement volume fraction (50%), Cu/Mo gave the lowest CTE, highest thermal conductivity and lowest electrical resistivity, while Cu/SiC gave the greatest hardness and Cu/TiB2 and Cu/SiC gave the highest compressive yield strength. Compared to Cu/SiC, Cu/TiB2 exhibited much higher thermal conductivity and much lower electrical resistivity. This revised version was published online in November 2006 with corrections to the Cover Date.     

Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

Effective thermal management of electronic integrated devices with high powder density has become a serious issue, which requires materials with high thermal conductivity (TC). In order to solve the problem of weak bonding between graphite and Cu, a novel Cu/graphite film/Cu sandwich composite (Cu/GF/Cu composite) with ultrahigh TC was fabricated by electro-deposition. The micro-riveting structure was introduced to enhance the bonding strength between graphite film and deposited Cu layers by preparing a rectangular array of micro-holes on the graphite film before electro-deposition. TC and mechanical properties of the composites with different graphite volume fractions and current densities were investigated. The results showed that the TC enhancement generated by the micro-riveting structure for Cu/GF/Cu composites at low graphite content was more effective than that at high graphite content, and the strong texture orientation of deposited Cu resulted in high TC. Under the optimizing preparing condition, the highest in-plane TC reached 824.3 W·m⁻¹·K⁻¹, while the ultimate tensile strength of this composite was about four times higher than that of the graphite film.     

热循环对片层石墨/铝复合材料的强度和热导率的影响

采用粉末冶金法制备片层石墨增强Al基复合材料(50vol％Gf/6061Al),Gf与Al基体结合紧密,界面处无裂纹、孔洞等缺陷.复合材料在-50～120℃温度范围内分别循环10次、50次、100次和200次,研究不同的循环次数对材料组织和性能的影响.结果 表明,循环不同次数时材料的密度没有明显的变化,但随着循环次数的...     

The thermal and mechanical properties of graphite foam/epoxy resin composites

A series of epoxy resin (EP) filled graphite foam (GF) composites were prepared to explore a new material with good heat transfer property. The effects of the mass fraction of EP and the network structure of GFs on the thermal diffusivity and the compression strength of the composites were investigated. The thermal diffusivity of the GF/EP composite with EP mass fraction of 91.45% was raised to 6.541 mm²/s, which was 45.7 times higher than the pure EP. The thermal conductivity reached to 14.67 W/(m K), which was 43.1 times higher than the pure EP. The compression strength of the GF/EP increased 55% above the value of pure EP. In addition, the thermal diffusivity of GF/EP increased with the decrease of the mass fraction of EP. A model was formulated to calculate the pressure needed for a mass fraction of EP.     

热压与放电等离子体烧结两种工艺制备Al2O3/Cu复合材料

由机械合金化法(MA)制得纳米级Al₂O₃颗粒弥散镶嵌于微米级Cu颗粒表面的复合粉末, 利用球形化工艺改善所制得复合粉的形貌及粒度范围, 分别采用热压法(HP)和放电等离子体烧结(SPS)法制备Al₂O₃/Cu复合材料。通过测试密度、 电导率、 抗弯强度及SEM复合粉形貌和烧结体断口分析、 微区成分分析, 对比研究了Al₂O₃质量分数分别为0%、 0.5%、 1.0%、 1.5%时Al₂O₃/Cu复合材料的物理、 力学和电学性能。结果表明: 不同制备工艺下随着Al₂O₃含量增加, 材料的抗弯强度先增后降, 电导率除受杂质影响外, 还受材料缺陷的影响, 故变化规律不明显, 对于Al₂O₃含量相同的Al₂O₃/Cu复合材料, 采用SPS法制备的复合材料的致密度、 抗弯强度及电导率均高于HP法; 在弯曲应力下两种制备方法所得复合材料均发生延性断裂。      

Mechanical properties of a diamond–copper composite with high thermal conductivity

Using pressureless infiltration of copper into a bed of coarse (180 μm) diamond particles pre-coated with tungsten, a composite with a thermal conductivity of 720 W/(m K) was prepared. The bending strength and compression strength of the composite were measured as 380 MPa. As measured by sound velocity, the Young's modulus of the composite was 310 GPa. Model calculations of the thermal conductivity, the strength and elastic constants of the copper–diamond composite were carried out, depending on the size and volume fraction of filler particles. The coincidence of the values of bending strength and compressive strength and the relatively high deformation at failure (a few percent) characterize the fabricated diamond–copper composite as ductile. The properties of the composite are compared to the known analogues — metal matrix composites with a high thermal conductivity having a high content of filler particles (~ 60 vol.%). In strength and ductility our composite is superior to diamond–metal composites with a coarse filler; in thermal conductivity it surpasses composites of SiC–Al, W–Cu and WC–Cu, and dispersion-strengthened copper.