聚乙烯醇交联改性对天然纤维增强聚丙烯复合材料性能的影响

采用聚乙烯醇(PVA)交联对洋麻(KF)增强聚丙烯(PP)、棕榈(PF)增强聚丙烯(PP)复合材料进行改性,通过模压成型工艺制备KF/PP和PF/PP复合材料。研究不同交联方法对复合材料的结构和性能的影响,采用SEM、DMA等技术研究了改性对复合材料的界面结合及力学性能影响。结果表明:PVA协同偶联剂交联改性对天然纤维/PP复合材料的综合改性效果最好,当用5%PVA+3%偶联剂对KF/PP改性时,KF/PP复合材料的弯曲强度提升25.2%,弯曲模量提升35.49%,剪切强度提升28%,分别达到了50.90 MPa、5.76 GPa、5.4MPa。当用5%PVA+2%偶联剂对PF/PP改性时,PF/PP复合材料的弯曲强度提升31.46%,弯曲模量提升27.07%,剪切强度提升21.75%,分别达到44.33MPa、2.32GPa、5.18MPa。改性后KF/PP、PF/PP复合材料的含水率分别下降了46.89%、10.63%,吸水率分别下降了8.57%、6.12%。KF/PP改性后储能模量提高20.93%,PF/PP改性后Tg值由90.1℃上升到113.8℃。SEM表明:PVA协同偶联剂交联改性有效改善了纤维与PP间的粘结,纤维与PP间的界面结合得到改善。     

碱处理对竹纤维及竹纤维增强聚丙烯复合材料性能的影响

为探究竹纤维表面能对纤维与树脂的粘附功及复合材料界面的影响,采用碱处理对竹纤维进行表面改性,通过模压工艺制备了竹纤维增强聚丙烯(PP)复合材料。研究了碱处理对竹纤维性能、竹纤维与PP间的粘附功及对竹纤维/PP复合材料力学性能的影响,采用SEM研究了不同浓度碱处理后竹纤维表面形貌的变化。结果表明:随着碱浓度的增加,竹纤维断裂强度呈现一定波动,当碱浓度为1wt%时竹纤维断裂强度达到最大值;竹纤维与PP的粘附功与竹纤维极性比密切相关,竹纤维极性比越小,粘附功越大;随着碱浓度增大,竹纤维与PP间粘附功与竹纤维/PP复合材料剪切性能呈现相同的趋势,并且都在碱浓度为20wt%时达到最大值,此时竹纤维与PP的粘附功较未处理时提高了67.18%;竹纤维/PP复合材料剪切性能较未处理时提高了23.29%;复合材料弯曲强度在碱浓度为5wt%时达到最大值,相比未处理时提高了23.13%。     

竹纤维质量分数对竹纤维增强聚乳酸复合材料性能影响

以1.5%异氰酸酯(MDI)界面改性剂改性处理后的竹纤维和聚乳酸为原料,通过注射成型工艺制备竹纤维增强聚乳酸复合材料,探讨竹纤维质量分数对复合材料界面、力学性能、吸水率、热性能的影响。结果表明,随着竹纤维质量分数的增加,复合材料拉伸强度、冲击强度、存储模量以及热稳定性均先增大后减小,24h吸水率逐渐增大,损耗因子逐渐降低。竹纤维质量分数为50%时,复合材料的拉伸强度和冲击强度分别达到最大值63.2/MPa和11.6/kJ/m2,复合材料存储模量最大,热稳定性最好。     

三维编织CF/KF混杂复合材料力学性能研究

考察了三维编织碳纤维/芳纶纤维混杂增强铸型尼龙(简称HF/MCPA)复合材料的力学性能,着重分析了复合材料的冲击、剪切和弯曲性能。试验结果表明:碳纤维和芳纶纤维混杂复合材料不仅有较好的弯曲强度、剪切强度,同时冲击强度也很好。随着碳纤维体积分数的增加,混杂复合材料的冲击强度降低;横向剪切强度先增大后降低;纵向剪切强度逐渐增大,出现最大值;弯曲强度和模量随之提高,达到最大值后开始下降,最大值时CF∶KF为3∶2。     

竹纤维质量分数对竹纤维增强聚乳酸复合材料性能影响

以1.5%异氰酸酯(MDI)界面改性剂改性处理后的竹纤维和聚乳酸为原料,通过注射成型工艺制备竹纤维增强聚乳酸复合材料,探讨竹纤维质量分数对复合材料界面、力学性能、吸水率、热性能的影响。结果表明,随着竹纤维质量分数的增加,复合材料拉伸强度、冲击强度、存储模量以及热稳定性均先增大后减小,24h吸水率逐渐增大,损耗因子逐渐降低。竹纤维质量分数为50%时,复合材料的拉伸强度和冲击强度分别达到最大值63.2MPa和11.6kJ/m2,复合材料存储模量最大,热稳定性最好。     

单向竹原纤维表面改性对其增强不饱和聚酯树脂复合材料性能的影响

采用碱处理、碱-偶联剂联合处理对竹原纤维进行表面改性,通过缝合-模压工艺制备了单向连续竹原纤维/不饱和聚酯树脂(BF/UP)复合材料。研究了不同表面改性方法对BF/UP复合材料静态、动态力学性能、吸水性能等的影响,并用SEM、红外光谱等技术研究了改性处理后纤维的表面及复合材料界面结合情况。结果表明:经过不同表面处理后BF/UP复合材料的性能均有所改善。当采用5wt%碱-3wt%偶联剂联合处理时,BF/UP复合材料综合性能最优,其拉伸强度、弯曲强度、弯曲模量、剪切强度较未处理的分别提高了34.29%、15.95%、11.26%、29.39%;复合材料存储模量(33℃)较未处理的提高了63.80%,损耗因子有所降低;BF/UP复合材料24h、720h吸水率较未处理的分别减小了55.35%、27.32%。SEM和红外光谱结果表明,改性处理后竹原纤维表面杂质减少,附着了一层偶联剂膜,BF/UP复合材料中纤维与树脂之间的界面结合更好。     

稀土改性对玄武岩纤维增强氰酸酯树脂复合材料性能的影响

采用自制稀土改性剂改性玄武岩纤维（La-BF）布增强双酚A型二氰酸酯（BADCy）制备了La-BF/BADCy复合材料。采用SEM和FTIR分析了改性对BF表面产生的影响,TG分析研究了改性对BF/BADCy复合材料热稳定性的影响,使用电子万能试验机研究改性对不同质量分数的BF/BADCy弯曲性能的影响,通过阻抗分析仪分析了改性对La-BF/BADCy复合材料介电性能的影响。结果表明,改性减少了BF的表面缺陷,并引入了结晶状凸起,有利于提高BF/BADCy复合材料的界面性能;通过改性提高了BF/BADCy复合材料的热稳定性,初始分解温度提高了145℃;当BF的质量分数为12wt%时,改性使BF/BADCy复合材料弯曲模量提高到4.19 GPa,弯曲强度达到110 MPa以上。在1 MHz~3 GHz范围内,La-BF/BADCy复合材料的介电常数稳定在1.9左右。因此稀土改性是一种能够有效提高BF/BADCy复合材料弯曲性能、热稳定性及介电性能的表面改性方法。      

建筑用碳纤维增强环氧树脂复合材料的制备及其性能研究

选择以T700碳纤维为增强相，将碳纤维经浓HNO₃浸渍处理0,40,80,120和160 min后掺入到环氧树脂中，制备了碳纤维增强环氧树脂复合材料。分析了浸渍时间对复合材料微观形貌、力学性能和热稳定性的影响。结果表明，经浓HNO₃浸渍的碳纤维表面粗糙度增大，沟槽数量和深度增加，碳纤维和环氧树脂的结合强度增大；随碳纤维浸渍时间的增大，复合材料的界面剪切强度、层间剪切强度、弯曲强度和弯曲模量均先增大后减小，当浸渍时间为120 min时，复合材料的界面剪切强度和层间剪切强度均达到了最大值，分别为80.2和90.3 MPa,其弯曲强度和弯曲模量也达到了最大值，分别为902.6 MPa和79.3 GPa,且应力-应变最高点增大，弯曲性能提高；在800℃下浓HNO₃浸渍处理120 min的复合材料的残炭率最大为58.2%,热稳定性最佳。     

废印刷电路板非金属粉增强及磨碎玻璃纤维增强聚丙烯力学性能

分别用废印刷电路板(PCB)非金属粉、磨碎玻璃纤维作为增强材料,采用熔融共混方法制备了聚丙烯(PP)基复合材料,并通过其力学性能试验和缺口冲击断面、废PCB非金属粉、磨碎玻璃纤维的形貌观察,分析研究了两种增强材料及表面改性对复合材料力学性能的影响。实验结果表明：废PCB非金属粉/PP复合材料力学性能得到了明显提高,其中拉伸强度、拉伸模量、弯曲强度和弯曲模量最大增幅分别为28%、41%、86%和133%;废PCB非金属粉与磨碎玻璃纤维都能作为PP增强填料,但其韧性降低;表面改性对废PCB非金属粉/PP复合材料力学性能的影响不大,但是对磨碎玻璃纤维/PP复合材料力学性能的影响大;废 PCB非金属粉/PP复合材料综合力学性能高于磨碎玻璃纤维/PP复合材料,可代替磨碎玻璃纤维作为PP基复合材料的增强填料,不仅可以减少环境污染,实现资源再利用,而且大大降低复合材料成本。     

汽车零部件包装用PP/SBN复合材料的性能研究

目的 研究单层氮化硼（Single-layer Boron Nitride, SBN）对聚丙烯（Polypropylene, PP）力学性能和摩擦性能的影响。方法 首先利用超声剥离和硅烷偶联剂KH550表面改性方法制得SBN,用高速混合机将PP、马来酸酐接枝聚丙烯（PP-g-MAH）和SBN混合均匀;然后利用注塑机通过熔融共混,制备PP/SBN复合材料。结果 当SBN质量分数低于1.6%时,PP/SBN的表面硬度和耐磨性能得到了进一步改善;当SBN质量分数高于1.6%时,PP/SBN的力学强度和摩擦性能降低;当SBN质量分数为1.6%时,PP/SBN的拉伸强度和冲击强度分别达到最大值（35.27 MPa, 34.69 kJ/m2）,较纯PP分别提高了10.7%, 18.8%。此时,PP/SBN的摩擦因数和磨损率较纯PP分别降低了15.1%, 32.4%。结论 当SBN质量分数为1.6%时,对PP具有增强增韧作用,复合材料的力学性能和耐磨性能都得到明显提高。     

聚丙烯/改性煤系高岭土复合材料的制备与性能

煤系高岭土经过硅烷偶联剂表面改性后,与聚丙烯(PP)树脂熔融共混制备出聚丙烯/改性煤系高岭土复合材料。通过X射线衍射、红外光谱、力学性能和扫描电镜分析,研究了改性煤系高岭土的填充量对复合材料力学性能的影响。结果表明,利用硅烷偶联剂可以实现煤系高岭土的表面改性。改性煤系高岭土填充量为3%时,复合材料具有最佳的冲击韧性。填充量为5%时,复合材料的断裂伸长率达到最大值。随着改性煤系高岭土填充量的增加,复合材料的弯曲强度和弯曲模量逐渐增大,填充量为10%时,二者比纯PP分别提高14.5%和27.5%。     

PP-g-Si与KH550对聚丙烯/滑石粉体系的增容效果

硅烷接枝聚丙烯（ＰＰ－ｇ－Ｓｉ）对聚丙烯／滑石粉（ＰＰ／Ｔａ）混合体系有一定的增容作用,可使复合材料的力学性能得以提高,占复合材料总质量３．５％的ＰＰ－ｇ－Ｓｉ（相当于含硅烷０．２％）对ＰＰ／Ｔａ体系的增容效果与含０．８％（质量分数）的ＫＨ５５０的增容效果相当,ＫＨ５５０对复合材料中聚丙烯（ＰＰ）的结晶熔融行为基本上无影响。而ＰＰ－ｇ－Ｓｉ能进一步使材料中ＰＰ的结晶峰温和熔融峰温提高。     

Influence of compatibilizing system on morphology,thermal and mechanical properties of high flow polypropylene reinforced with short hemp fibers

Simultaneous influence of polypropylene-graft-maleic anhydride (MAPP) and silane-treated hemp fibers (HF) on morphology, thermal and mechanical properties of high-flow polypropylene (PP) modified with poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS) was studied in this paper. The addition of SEBS reduced the efficiency of MAPP in PP composites with HF, thus silane-treated fibers (HFs) were used to improve polymer–fiber interface. Thermal stability of HF was improved after silane treatment and less than 2% weight loss was observed at 240 °C in composites with 30 wt% HF. Better dispersion of fibers and better efficiency in enhancing static and dynamic mechanical properties of PP, doubling its strength and stiffness were observed in composites with treated fibers compared to untreated ones. High ability to absorb and dissipate energy and well-balanced strength and stiffness were showed by PP modified with SEBS and MAPP containing 30 wt% HFs. These composites were studied as an alternative to conventional PP/glass fibers composites for injection molding of small to medium auto parts.     

Direct fluorination as a novel organophilic modification method for the preparation of Illite/polypropylene nanocomposites

This study reports the application of illite as a clay filler and direct fluorination as an organophilic modification for clays. Illite was also modified using conventional methods, with reagents such as 3-aminopropyltrimethoxysilane and hexadecyl-trimethoxysilane for comparison of the resultant illite/polypropylene (PP) composites with the fluorinated illite/PP composites. The thermal properties, flame retardancy, and mechanical properties of the resultant composites were also investigated. Fluorination of illite resulted in exfoliation and more thermally stable organophilic modification compared with the conventional silane treatment. When comparing two different silane-treated illite/PP composites with fluorinated illite/PP composites, fluorinated illite had better thermal stability and exfoliation after modification and more improved dispersion in PP matrix. This resulted in improved thermal stability, flame retardancy, and mechanical properties compared with the silane-treated illite/PP composites. The fluorinated illite/PP composite exhibited a 28% increase in thermal stability and a 50% increase in flame retardancy compared with neat PP. Fluorination of illite yielded at least 50% further improvement in the thermal stability and flame retardancy of the resulting illite/PP composites compared with the conventional silane treatments.     

PP/POE/高岭土三元复合材料的力学及热性能

研究了高岭土和乙烯-辛烯共聚物弹性体(POE)填充聚丙烯(PP)制备的PP/POE/高岭土三元复合材料的力学和热力学性能。结果表明,POE和高岭土不能提高PP的拉伸强度,但高岭土可以显著提高PP/POE的杨氏模量。POE降低了PP的弯曲强度和弯曲模量,但PP/POE/高岭土三元复合材料的弯曲强度和弯曲模量显著高于PP/POE和PP。POE和高岭土可以显著提高PP的冲击强度,当高岭土和POE的填充份数分别为10份和5份时,PP/POE/高岭土复合材料的冲击强度最大。高岭土的添加可以提高PP的结晶温度,加快PP的结晶速率,促进PP的异相成核。合适含量的高岭土可以提高PP的熔融温度,改善PP的耐热性能。     

Mechanical behaviour of agro-residue reinforced poly(3-hydroxybutyrate-co-3-hydroxyvalerate), (PHBV) green composites: A comparison with traditional polypropylene composites

Novel green composites were successfully fabricated by incorporating agro-residues as corn straw (CS), soy stalk (SS) and wheat straw (WS) into the bacterial polyester, poly(3-hydroxybutyrate-co-3-hydroxyvalerate), PHBV, by melt mixing technique. Effects of these biomass fibers on mechanical, thermal, and dynamic mechanical properties of PHBV were investigated. A comparative study of biomass fiber-reinforced polypropylene composite systems was performed. The tensile and storage modulus of PHBV was improved by maximum 256% and 308% with the reinforcement of 30 wt.% agricultural byproducts to it. For equal amounts of (30%) biomass fibers, tensile and flexural modulii of PHBV composites showed much higher values than corresponding PP composites. Alkali treatment of wheat straw fibers enhanced strain @ break and impact strength of PHBV composites by ∼35%, hardly increasing strength and modulus compared to their untreated counterparts. DMA studies indicated better interfacial interaction of PHBV with the biomass fibers than PP. Scanning electron microscopy (SEM), used to study the morphology of composites, also revealed similar outcomes.     

Mechanical Properties of Thermoplastic and Thermoset Composites Reinforced with 3D Biaxial Warp-knitted Fabrics

In this study, two types of thermoplastic matrices (low melting point polyethylene terephthalate (LPET) fiber and polypropylene (PP) fiber) and glass fiber/epoxy resin/multi-walled carbon nanotubes (MWCNTs) were used to fabricate the thermoplastic and thermoset composite materials with 3D biaxial warp-knitted fabrics. Thermoplastic and thermoset composites were fabricated using hot-press and resin transfer molding (RTM) methods. The fabricated samples were tested with tensile and three-point flexural tests. In thermoplastic composites, samples in the 90° direction and LPET matrix showed the best tensile and flexural properties with an improvement of 39 and 21% tensile modulus and strength, 16 and 8% flexural modulus and strength compared to the PP samples in the same direction. In thermoset composites, samples in the 90° direction and MWCNTs showed the best improvement of the flexural modulus and strength with 97 and 58% compared to the samples without MWCNTs. This improvement can most likely be attributed to an increase in interfacial adhesion due to the presence of the carbon nanotubes.     

类水滑石的制备与改性及其在聚丙烯阻燃中的应用

采用共沉淀法制备了镁铝类水滑石（LDHs）前驱体,加入少量聚磷酸铵（APP）制得APP-LDHs,探讨了不同质量分数APP对LDHs晶体生长的影响;当APP在LDHs前驱浆液中添加量为0.8wt%时,将APP-LDHs与季戊四醇（PER）、硅烷偶联剂KH-550进行球磨混合,制备插层包覆改性的LDHs;通过XRD、FTIR、SEM和TG等对改性前后的LDHs进行了表征;采用极限氧指数（LOI）、垂直燃烧测试（UL-94）、缺口冲击和弯曲实验等方法研究了LDHs改性前后LDHs/聚丙烯（PP）复合材料的阻燃性能及力学性能的差异。研究结果表明：APP的加入,未显著影响LDHs的层板生长,但其层板堆叠受到抑制;SEM观察表明,所制备的LDHs为片状,且经插层包覆改性后的LDHs粉体形貌较为规整,颗粒粒径为100~250 nm;改性LDHs在较高温度下的热稳定性显著优于未改性的LDHs;当PP中加入质量分数为20%的LDHs及改性LDHs时,可抑制PP燃烧时产生的熔滴,并促使LDHs/PP复合材料表面形成炭层;改性LDHs/PP复合材料具有更好的阻燃性能,且其冲击强度、弯曲强度等力学性能下降不明显。