共查询到20条相似文献,搜索用时 62 毫秒
1.
采用预辐射接枝法,将N-异丙基丙烯酰胺(N-Isopropylacryamide,NIPAAm)接枝于聚丙烯纤维。研究了不同条件下接枝纤维对亚铁离子的吸附和解吸附情况。结果表明,在较低温度(5℃)及pH≈10条件下,接枝纤维对金属离子(Fe^2+)具有良好的吸附性能;而在较高温度(50℃)下pH≈3时,被吸附的Fe^2+几乎能被较完全解脱下来。 相似文献
2.
将丙烯酸(AA)与丙烯酰胺(AM)通过预辐照接枝在苎麻纤维上,通过协同作用提高其接枝率,并研究了其对Cu2+的吸附性能。傅里叶红外光谱(FT-IR)对苎麻纤维表面分析结果显示,AA及AM成功接枝在苎麻纤维上,吸收剂量为35kGy时,接枝率可达151%(AA与AM浓度比为1∶1)。对Cu2+的吸附实验结果表明,接枝后的苎麻纤维在吸附反应初期,Cu2+吸附量迅速增加,20~30min增加速度变缓,30min后趋于饱和;随着温度升高,吸附量迅速增加,但温度高于40℃后,吸附量不再增加;吸附量随初始Cu2+浓度的增加而增大,在初始浓度为1 000mg/L的Cu2+溶液中,苎麻纤维的Cu2+吸附量可达14.40mg/g。 相似文献
3.
用批式法研究了大气条件下99Tc在Fe,Fe2O3和Fe3O4上的吸附行为,考察了吸附平衡后溶液中99Tc的存在价态.实验结果表明随着溶液pH值(5~12)、CO2-3浓度(1×10-8~1×10-2 mol/L)的增大,99Tc在Fe上的吸附比减小;溶液pH值、CO2-3浓度的变化基本不影响99Tc在Fe2O3和Fe3O4上的吸附;99Tc在这3种吸附材料上的吸附行为均可用Freundlich吸附等温式表示;当Fe作吸附材料时,吸附平衡后99Tc主要以Tc(Ⅳ)的形式被吸附,当Fe2O3和Fe3O4作为吸附材料时,99Tc主要以Tc(Ⅶ)的形式被吸附. 相似文献
4.
5.
聚丙烯胺肟螯合纤维的辐射合成及其对Pb(Ⅱ)离子的吸附性能 总被引:1,自引:0,他引:1
采用预辐照接枝法,在空气或氮气气氛下利用电子束对聚丙烯纤维进行辐照。然后,将样品置于4种不同溶剂(水、甲醇、正丁醇、10%甲醇水溶液)的丙烯腈溶液体系中进行接枝反应,并通过与盐酸羟胺溶液反应,引入胺肟基团,获得一种机械性能较好的偕胺肟螯合纤维(PPAO)。最后浸于硝酸铅标准溶液中,测定其对铅的吸附量。结果表明,接枝率与预辐照气氛、反应温度、反应液体积、单体浓度都有密切关系。聚丙烯纤维在水溶液和10%甲醇水溶液中接枝率较高。当纤维在空气中预辐照,丙烯腈单体体积浓度为30%,温度为70℃时,聚丙烯纤维的接枝率最高;对Pb(Ⅱ)的吸附容量为0.362mg/g(纤维)。 相似文献
6.
铀在木纤维上的吸附行为及机理分析 总被引:4,自引:2,他引:4
为了解木纤维对铀的吸附特性,通过静态吸附实验,研究了木纤维的粒度、吸附时间、用量、温度及溶液的pH值和初始浓度等因素对模拟含铀废水中U(Ⅵ)去除率的影响,并从热力学和动力学方面对吸附过程进行了分析。结果表明:溶液初始pH≈3时,木纤维对铀的吸附平衡时间为4h,且吸附剂粒径越小、温度越高、用量越大,越有利于铀的去除;铀在木纤维上的吸附过程符合Langmuir等温吸附方程,吸附动力学过程可用准二级吸附动力学模型描述,表明化学吸附主要受动力学控制;木纤维吸附铀是自发的吸热反应。SEM、FT-IR和EDS分析结果表明,木纤维吸附铀后表面形态发生了改变,且在吸附过程中铀主要与木纤维表面活性基团螯合并形成配合物,存在表面络合吸附行为;吸附铀前后的能谱对比分析表明,吸附过程中存在离子交换行为。因此,木纤维对铀的吸附机理是以离子交换和表面络合吸附为主、物理吸附为辅的混合吸附过程。 相似文献
7.
利用预辐射接枝技术制备含有季铵盐官能团的超高分子量聚乙烯(UHMWPE-g-P(GMA-co-MA)-TETA- GTA)纤维。研究该纤维对Au(III)的吸附性能,重点考察了起始溶液的pH值、初始Au(III)离子浓度和温度对吸附容量的影响。实验结果表明,UHMWPE-g-P(GMA-co-MA)-TETA-GTA 纤维对 Au(III)的吸附速率较快、吸附容量大,180 min内能够达到吸附平衡;在溶液的pH值为3时吸附容量最大(355 mg/g)。该吸附过程符合准二级动力学模型和和Langmuir等温吸附模型,吸附反应是一个熵减少的放热反应。 相似文献
8.
研究了在模拟地下水介质中,混凝土对碘的吸附(解吸)规律和吸附等温线。实验表明,在30±2℃、c_I=10~(-6)mol/l、pH=9.01条件下的分配比R_(D_a)=3.16±0.32ml/g。还对酸度、固液比、固体比表面和还原剂Fe、(NH_2)_2存在时对R_D值的影响进行了研究。 相似文献
9.
用批式法研究了99Tc在Ca-基膨润土中的吸附行为.大气条件下,99Tc在膨润土中的吸附比约为1.47 mL/g,随着溶液pH值、CO2-3、Fe3+浓度的增大,99Tc在膨润土中的吸附比基本不变;随着添加剂Fe2O3和Fe3O4加入量以及Fe2+浓度的增大,99Tc在膨润土中的吸附比增大,吸附平衡后,99Tc主要以Tc(Ⅶ)的形式存在;随着添加剂Fe加入量的增大,99Tc在膨润土中的吸附比增大,吸附平衡后,99Tc主要以Tc(Ⅳ)的形式存在.低氧条件下,99Tc在膨润土中的吸附比约为84.84 mL/g,随着溶液pH值、CO2-3浓度的增大,99Tc在膨润土中的吸附比减小;随着溶液Fe2+、Fe3+浓度以及添加剂Fe、Fe2O3和Fe3O4加入量的增大,99Tc在膨润土中的吸附比增大,低氧条件下99Tc主要以Tc(Ⅳ)的形式存在.大气与低氧条件下,99Tc在膨润土中的吸附行为均可用Freundlich吸附等温式表示. 相似文献
10.
以三乙氧基(3-异氰酸丙基)硅为交联剂,通过后接枝法合成了β-环糊精改性介孔二氧化硅(SBA-15-CD)材料。通过静态吸附试验研究了溶液pH值、SBA-15-CD投加量、吸附时间、温度等因素对SBA-15-CD吸附U(Ⅵ)的影响。通过扫描电镜(SEM)、X射线粉末衍射(XRD)、BET比表面分析、傅里叶红外光谱(FT-IR)和X射线光电子能谱(XPS)对材料进行表征分析,并探讨了SBA-15-CD吸附U(Ⅵ)的机制。结果表明,当U(Ⅵ)初始浓度为5 mg/L、温度为30 ℃时,SBA-15-CD吸附U(Ⅵ)的最佳条件为:pH=5、SBA-15-CD投加量0.20 g/L、吸附平衡时间30 min,在此条件下,平衡吸附量为24.4 mg/g,U(Ⅵ)去除率为98.3%。吸附过程符合准二级动力学模型和Langmuir等温模型,即以化学吸附为主,且主要是通过表面的羟基、酯基和氨基与U(Ⅵ)配位。30 ℃下SBA-15-CD的饱和吸附量达330 mg/g,升高温度有利于吸附的进行。SBA-15-CD具有良好的重复使用性能。 相似文献
11.
LIU Xiuhua XU Yunshu ZHONG Zhijing FU Yibei DENG Yi 《核技术(英文版)》2007,18(1):59-64
Zn-doped TiO2 catalysts were prepared using a sol-gel method and characterized by XPS,UV-Vis, BET, XRD in this study. Under the irradiation of simulant sunlight, the photocatalytic activity for the degradation of p-nitrophenol was studied too. After irradiation for 2.5 h, the degradation percentage of p-nitrophenol could rise to more than 80 %. The results showed that the spectrum absorption band edge of Zn/TiO2 powder does not broaden obviously comparing with pure TiO2 powder. Zinc exists as Zn (11). When calcined at 973 K, there is a new phase as ZnTiO3 in Zn/TiO2 catalyst. The order of photocatalytic activity of Zn/TiO2 catalysts calcined at different temperatures for p-nitrophenol is 773 K 〉 673 K 〉 873 K 〉 573 K 〉 973 K and the photocatalytic activity of Zn/TiO2 catalyst calcined at 773 K is better than TiO2 catalysts heated at the same temperature, and outclasses that of commercial TiO2 catalyst. It also showed that the photocatalytic degradation of p-nitrophenol follows first-order kinetics under the irradiation of simulant sunlight. 相似文献
12.
FU Shen SUNYi LU Yaohong 《核技术(英文版)》2007,18(2):65-72
Radiotherapy for the treatment of prostate cancer has been extensively explored in the past. Along with the comprehensive understanding of the biology of prostate cancer and rapid advances in terms of technology, the out- come of treatment for the patients with prostate cancer has improved. The authors review radiotherapy as the primary treatment for the disease, with particular emphasis on the technological advances from both the radiobiological and radiophysics aspects. Nonconventional fractionated irradiation like hyper- or hypo-fractionation has been imple- mented in the clinic, the final results still need to be confirmed in the future. Technological advances like IMRT, IGRT, in the last two decades have significantly improved the delivery of external radiotherapy to the prostate. This has re- sulted in an overall increase in the total dose that can be safely delivered to the prostate, which has led to modest im- provements in the biochemical outcome. However, establishing the standard therapy for prostate cancer remains con- troversial. It is hoped that the next decades will bring continued advances in the development of biologicals that will further improve current clinical outcomes. 相似文献
13.
This paper introduces the injection and extraction control system design for SSRF,which is a distributed control system aimed at stability and reliability of the pulse power supplies,PPS(Personnel Protection System)and MPS(Machine Protection System).The hardware environment is mainly based on PLC(Programmable Logic Con- troller),and ARM(Advanced RISC Machine)is also applied for studying stability of the power supplies.WinCC and EPICS(Experimental Physics and Industrial Control System)have been selected as the platforms of SCADA(Super- visory Control and Data Acquisition).For unifying the interfacing to the control computer,all front-end equipments are connected via Industrial Ethemet. 相似文献
14.
为研究含空气蒸汽在水平管内强制对流冷凝换热特性,基于对传热传质过程的分析,建立了管内为环状流与波状流条件下的流动冷凝换热模型。从潜热、显热和液膜3个环节对整个换热过程进行建模,最终得到计算局部冷凝换热系数的理论关系式。模型预测结果与实验数据的对比表明,二者相对偏差在±20%以内,验证了该换热模型的准确性与适用性。通过进一步的研究发现:从换热管入口至出口,随着冷凝的进行,管内换热主要热阻由液膜热阻向气液界面的凝结热阻转变;主流气体对流换热过程基本可忽略。 相似文献
15.
D.Rezaei OCHBELAGH H.Miri HAKIMABAD R.Izadi NAJAFABADI 《核技术(英文版)》2007,18(4):237-241
Experiments were carried out to investigate the possible use of neutron backscattering for the detection of polyethylene (PE) sample buried in the soil. In detection of landmine by neutrons, the neutron detector and its shield play an important role. In this paper, the effects of graphite, heavy water, polyethylene and boric acid moderators on the flux of back scattered neutrons were investigated. We have also experimentally verified the effect of BF3 detector shield and obtained good agreement with theory. 相似文献
16.
LI Lin SHEN Liren ZHU Qing WAN Tianmin 《核技术(英文版)》2007,18(4):193-197
Accelerator database stores various static parameters and real-time data of accelerator. SSRF (Shanghai Synchrotron Radiation Facility) adopts relational database to save the data. We developed a data retrieval system based on XML Web Services for accessing the archive data. It includes a bottom layer interface and an interface applicable for accelerator physics. Client samples exemplifying how to consume the interface are given. The users can browse, retrieve and plot data by the client samples. Also, we give a method to test its stability. The test result and performance are described. 相似文献
17.
为对自制的活性面积高达1 000 cm2的大面积源进行表面发射率定值,同时作为现有2πα、2πβ表面发射率标准装置能力的扩充,研制了一套内置式大面积2π多丝正比计数器测量系统,并利用活性区直径为8 mm的241Am点源及活性区面积为10 cm×15 cm的大面积241Am和90Sr-90Y源对其进行计量学性能测试。结果表明:计数器内计数响应均匀性优于±0.4%,有效探测面积达1 400 cm2;所得241Am源高压坪曲线的坪长为1 400 V,坪斜为0.27%/100 V,坪区内计数变化为0.87%;90Sr-90Y源高压坪曲线的坪长为300 V,坪斜为0.75%/100 V,坪区内计数变化为0.80%;10次测量重复性好于0.4%,8 h内短期稳定性好于0.3%,1 a内长期稳定性好于0.8%。 相似文献
18.
Distributions of natural gamma-emitting radionuclides were determined in 93 oil samples collected from some petroleum fields in the western desert of Egypt. The radioisotope activities in the area under investigation lay in the range of (21 ± 4) to (38 ± 13) Bq?L-1 for 226Ra, (9 ± 2) to (15 ± 5) Bq?L-1 for 232Th, and (154 ± 28) to (303 ± 54) Bq?L-1 for 40K. The mean values were 27, 12, and 201 Bq?L-1, respectively. Among oils, variations in radionuclide ac- tivities could be on account of differences in TDS, HCO3, and Ba, with high or low pH. In this environment, oil prop- erties differently affected the mobilization of natural radionuclides. The range of 226Ra variation had been compared with available data from other countries. The calculated absorbed dose rate ranged from 22.33 to 32.66 nGy?h-1 in lo- cation (B) and (E) respectively, which was less than the accepted value. 相似文献
19.
In this work,TTHMP was synthesized and labelled with 117m Sn.The preparation conditions,stability and lipophilicity of 117m Sn(IV)-TTHMP were investigated.Biodistribution of the complex in rabbits and mice was studied.It was found that the quantity of TTHMP and pH value of the prepararion solution had vital effects on the labeling yield of 117m Sn(IV)-TTHMP.It was also found that 117m Sn(IV)-TTHMP was hydrophilic and stable at room temperature and 37℃ in open air 117m Sn(IV)-TTHMP showed unexpectedly high bone uptake and bone-to-blood ratio in the animals.This made it potentially useful as an reagent for skeletal scintigraphy and radiotherapy of bone tumors. 相似文献
20.
LI Zhaobin XIONG Fei HUANG Guofeng CAO Zheng JIANG Ruiyao FU Shen 《核技术(英文版)》2007,18(3):145-149
Linear accelerators equipped with multileaf collimators (MLC) are becoming more common and are widely used in the intensity-modulated radiotherapy (IMRT). There is an imperative need to ensure the commissioning specification of the linear accelerators for the sake of quality assurance (QA) and quality control (QC). This paper is aimed to investigate the role of AGFA high-energy CR (Computed Radiography) in calibrating dynamic multileaf collimators and evaluating the accuracy of the leaf position. The result shows that AGFA high-energy CR can easily and conveniently be used to calibrate MLC and verify its position. Hence, the application of AGFA high-energy CR is proved to be an accurate and time-saving method for routine MLC QC, especially when MLC calibration adjustments are required. 相似文献