Ce1−xCuxO2−x/Al2O3/FeCrAl catalysts for catalytic combustion of methane

A series of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts (x = 0–1) were prepared. The structure of the catalysts was characterized using XRD, SEM and H₂-TPR. The catalytic activity of the catalysts for the combustion of methane was evaluated. The results indicated that in the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts the surface phase structure were the Ce_1−xCu_xO_2−x solid solution, -Al₂O₃ and γ-Al₂O₃. The surface particle shape and size were different with the variety of the molar ratio of Ce to Cu in the Ce_1−xCu_xO_2−x solid solution. The Cu component of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts played an important role to the catalytic activity for the methane combustion. There were the stronger interaction among the Ce_1−xCu_xO_2−x solid solution and the Al₂O₃ washcoats and the FeCrAl support.     

富铈Ce1-xLaxO2催化甲烷氧氯化性能

以硝酸铈、硝酸镧为前体,用氨水共沉淀法制备了一系列Ce_1-xLa_xO₂(x≤0.5)催化剂,利用XRD、N₂吸附-脱附、SEM、Raman、H₂-TPR和OSC对催化剂的物理化学性质进行了表征,并考察其在甲烷氧氯化反应中的催化性能。结果表明:Ce_1-xLa_xO₂催化剂的氧化还原性质随着镧含量的变化发生显著改变,并且这一性质的变化与反应的转化率及产物分布具有较强的联系。Ce_1-xLa_xO₂表面氧物种的活泼性对催化剂活性影响显著,而体相氧物种容易将生成的甲烷氯化物深度氧化。在Ce_1-xLa_xO₂(x<0.3)催化剂上表面氧物种起主导作用,氯甲烷为主要反应产物,Ce_0.8La_0.2O₂催化剂上氯甲烷选择性最高为52%。在体相氧物种更活泼的Ce_0.7La_0.3O₂和Ce_0.5La_0.5O₂上产物中CO的选择性显著上升,Ce_0.5La_0.5O₂催化剂上CO选择性高达48%。稳定性测试表明Ce_0.8La_0.2O₂催化剂具有良好的稳定性。     

AFeO3 (A=La, Nd, Sm) and LaFe1−xMgxO3 perovskites as methane combustion and CO oxidation catalysts: structural, redox and catalytic properties

Catalytic methane combustion and CO oxidation were investigated over AFeO₃ (A=La, Nd, Sm) and LaFe_1−xMg_xO₃ (x=0.1, 0.2, 0.3, 0.4, 0.5) perovskites prepared by citrate method and calcined at 1073 K. The catalysts were characterized by X-ray diffraction (XRD). Redox properties and the content of Fe⁴⁺ were derived from temperature programmed reduction (TPR). Specific surface areas (SA) of perovskites were in 2.3–9.7 m² g⁻¹ range. XRD analysis showed that LaFeO₃, NdFeO₃, SmFeO₃ and LaFe_1−xMg_xO₃ (x·0.3) are single phase perovskite-type oxides. Traces of La₂O₃, in addition to the perovskite phase, were detected in the LaFe_1−xMg_xO₃ catalysts with x=0.4 and 0.5. TPR gave evidence of the presence in AFeO₃ of a very small fraction of Fe⁴⁺ which reduces to Fe³⁺. The fraction of Fe⁴⁺ in the LaFe_1−xMg_xO₃ samples increased with increasing magnesium content up to x=0.2, then it remained nearly constant. Catalytic activity tests showed that all samples gave methane and CO complete conversion with 100% selectivity to CO₂ below 973 and 773 K, respectively. For the AFeO₃ materials the order of activity towards methane combustion is La>Nd>Sm, whereas the activity, per unit SA, of the LaFe_1−xMg_xO₃ catalysts decreases with the amount of Mg at least for the catalysts showing a single perovskite phase (x=0.3). Concerning the CO oxidation, the order of activity for the AFeO₃ materials is Nd>La>Sm, while the activity (per unit SA) of the LaFe_1−xMg_xO₃ catalysts decreases at high magnesium content.     

Electronic and chemical properties of mixed-metal oxides: basic principles for the design of DeNOx and DeSOx catalysts

Correlations between the electronic and chemical properties of perovskites, molybdates, and metal-doped MgO or CeO₂ are examined. Simple models based on band-orbital mixing can explain trends found for the interaction of these catalytic materials with adsorbates: the less stable the occupied levels of a mixed-metal oxide, the higher its chemical reactivity. Metal↔oxygen↔metal interactions are common in mixed-metal oxides and can lead to substantial changes in the electronic and chemical properties of the cations. This is particularly true in the case of ABO₃ perovskites (A=Pb, Ca, Sr, Li, K, Na; B=Ti, Zr, Nb), and it is an important phenomenon that has to be considered when mixing AO and BO₂ oxides for catalytic applications. In systems like Ce_1−xZr_xO₂ and Ce_1−xCa_xO₂, the structural stress induced by the dopant (Zr or Ca) leads to perturbations in the electronic properties of the Ce cations. The trends in the behavior of metal-doped MgO illustrate a basic principle in the design of mixed-metal oxide catalysts for DeNO_x and DeSO_x operations. The general idea is to find metal dopants that upon hybridization within an oxide matrix remain in a relatively low oxidation state and at the same time induce occupied electronic states located well above the valence band of the host oxide. Electronic effects should not be neglected a priori when explaining the behavior or dealing with the design of mixed-metal oxide catalysts.     

Preparation of CexZr1−xO2 (x = 0.75, 0.62) solid solution and its application in Pd-only three-way catalysts

Nanoparticles of Ce_xZr_1−xO₂ (x = 0.75, 0.62) were prepared by the oxidation-coprecipitation method using H₂O₂ as an oxidant, and characterized by N₂ adsorption, XRD and H₂-TPR. Ce_xZr_1−xO₂ prepared had single fluorite cubic structure, good thermal stability and reduction property. With the increasing of Ce/Zr ratio, the surface area of Ce_xZr_1−xO₂ increased, but thermal stability of Ce_xZr_1−xO₂ decreased. The surface area of Ce_0.62Zr_0.38O₂ was 41.2 m²/g after calcination in air at 900 °C for 6 h. TPR results showed the formation of solid solution promoted the reduction of CeO₂, and the reduction properties of Ce_xZr_1−xO₂ were enhanced by the cycle of TPR-reoxidation. The Pd-only three-way catalysts (TWC) were prepared by the impregnation method, in which Ce_0.75Zr_0.25O₂ was used as the active washcoat and Pd loading was 0.7 g/L. In the test of Air/Fuel, the conversion of C₃H₈ was close to 100% and NO was completely converted at λ < 1.025. The high conversion of C₃H₈ was induced by the steam reform and dissociation adsorption reaction of C₃H₈. Pd-only catalyst using Ce_0.75Zr_0.25O₂ as active washcoat showed high light off activity, the reaction temperatures (T₅₀) of 50% conversion of CO, C₃H₈ and NO were 180, 200 and 205 °C, respectively. However, the conversions of C₃H₈ and NO showed oscillation with continuously increasing the reaction temperature. The presence of La₂O₃ in washcoat decreased the light off activity and suppressed the oscillation of C₃H₈ and NO conversion. After being aged at 900 °C for 4 h, the operation windows of catalysts shifted slightly to rich burn. The presence of La₂O₃ in active washcoat can enhance the thermal stability of catalyst significantly.     

Electronic and structural properties of SnxTi1−xO2 solid solutions: a periodic DFT study

The structural and electronic properties of selected compositions of Sn_xTi_1−xO₂ solid solutions (x=0, 1/24, 1/16, 1/12, 1/8, 1/6, 1/4, 1/2, 3/4, 5/6, 7/8, 11/12, 15/16, 23/24 and 1) were investigated by means of periodic density functional theory (DFT) calculations at B3LYP level. The calculations show that the corresponding lattice parameters vary non-linearly with composition, supporting positive deviations from Vegard’s law in the Sn_xTi_1−xO₂ system. Our results also account for the fact that chemical decomposition in Sn_xTi_1−xO₂ system is dominated by composition fluctuations along [0 0 1] direction. A nearly continuous evolution of the direct band gap and the Fermi level with the growing value of x is predicted. Ti 3d states dominate the lower portion of the conduction band of Sn_xTi_1−xO₂ solid solutions. Sn substitution for Ti in TiO₂ increases the oxidation–reduction potential of the oxide as well as it renders the lowest energy transition to be indirect. These two effects can be the key factors controlling the rate for the photogenerated electron–hole recombination. These theoretical results are capable to explain the enhancement of photoactivity in Sn_xTi_1−xO₂ solid solutions.     

The homogeneity range and the microwave dielectric properties of the BaZn2Ti4O11 ceramics

Ceramics with a composition close to BaZn₂Ti₄O₁₁ were synthesized according to various substitutional mechanisms in order to verify an existence of a homogeneity range in the vicinity of this composition. Structural and microstructural investigations showed that the crystal structure of BaZn₂Ti₄O₁₁ was formed in the homogeneity range corresponding to the formula BaZn_2 − xTi₄O_11 − x (0 < x < 0.1). Densely sintered BaZn_2 − xTi₄O_11 − x (0 < x < 0.1) ceramics exhibited a dielectric constant around 30, τ_f = −30 ppm/K and high Q × f values, which increased from 68,000 GHz at x = 0 to 83,000 GHz at x = 0.05. Structurally, the deficiency of Zn in BaZn_2 − xTi₄O_11 − x (0 < x < 0.1) resulted in a slight decrease in the unit-cell volume. The influence of secondary phases in the BaZn₂Ti₄O₁₁-based materials on the microwave dielectric properties was also investigated. A presence of small amounts of ZnO, BaTiO₃, hollandite-type solid solutions (Ba_xZn_xTi_8 − xO₁₆) and BaTi₄O₉ caused a decrease in Q × f values.     

Catalytic reduction of sulfur dioxide using hydrogen or carbon monoxide over Ce1−xZrxO2 catalysts for the recovery of elemental sulfur

This study focuses on the direct sulfur recovery process (DSRP), in which SO₂ can be directly converted into elemental sulfur using a variety of reducing agents over Ce_1−xZr_xO₂ catalysts. Ce_1−xZr_xO₂ catalysts (where x = 0.2, 0.5, and 0.8) were prepared by a citric complexation method. The experimental conditions used for SO₂ reduction were as follow: the space velocity (GHSV) was 30,000 ml/g_-cat h and the ratio of [CO (or H₂, H₂ + CO)]/[SO₂] was 2.0. It was found that the catalyst and reducing agent providing the best performance were the Ce_0.5Zr_0.5O₂ catalyst and CO, respectively. In this case, the SO₂ conversion was about 92% and the sulfur yield was about 90% at 550 °C. Also, a higher efficiency of SO₂ removal and elemental sulfur recovery was achieved in the reduction of SO₂ with CO as a reducing agent than that with H₂. In the reduction of SO₂ by H₂ over the Ce_0.5Zr_0.5O₂ catalyst, SO₂ conversion and sulfur yield were about 92.7% and 73%, respectively, at 800 °C. Also, the reduction of SO₂ using synthetic gas with various [CO]/[H₂] molar ratios over the Ce_0.5Zr_0.5O₂ catalyst was performed, in order to investigate the possibility of using coal-derived gas as a reducing agent in the DSRP. It was found that the reactivity of the SO₂ reduction using the synthetic gas with various [CO]/[H₂] molar ratios was increased with increasing CO content of the synthetic gas. Therefore, it was found that the Ce_1−xZr_xO₂ catalysts are applicable to the DSRP using coal-derived gas, which contains a larger percentage of CO than H₂.     

Ceria-based oxides as supports for LaCoO3 perovskite; catalysts for total oxidation of VOC

Supported LaCoO₃ perovskites with 10 and 20 wt.% loading were obtained by wet impregnation of different Ce_1−xZr_xO₂ (x = 0–0.3) supports with a solution prepared from La and Co nitrates, and citric acid. Supports were also prepared using the “citrate method”. All materials were calcined at 700 °C for 6 h and investigated by N₂ adsorption at −196 °C, XRD and XPS. XRD patterns and XPS measurements evidenced the formation of a pure perovskite phase, preferentially accumulated at the outer surface. These materials were comparatively tested in benzene and toluene total oxidation in the temperature range 100–500 °C. All catalysts showed a lower T₅₀ than the corresponding Ce_1−xZr_xO₂ supports. Twenty weight percent LaCoO₃ catalysts presented lower T₅₀ than bulk LaCoO₃. In terms of reaction rates per mass unit of perovskite calculated at 300 °C, two facts should be noted (i) the activity order is more than 10 times higher for toluene and (ii) the reverse variation with the loading as a function of the reactant, a better activity being observed for low loadings in the case of benzene. For the same loading, the support composition influences drastically the oxidative abilities of LaCoO₃ by the surface area and the oxygen mobility.     

Synthesis, characterization and catalytic activity for NO–CO reaction of Pd–(La, Sr)2MnO4 system

La_xSr_2−xMnO₄ (0 ≤ x ≤ 0.8) oxides were synthesized and single-phase K₂NiF₄-type oxides were obtained in the range of 0.1 ≤ x < 0.5. The catalytic activity of La_xSr_2−xMnO₄ for NO–CO reaction increased with increasing x in the range of solubility limit of La. La_0.5Sr_1.5MnO₄ showed the highest activity among La_xSr_2−xMnO₄ prepared in this study, but its activity was inferior to perovskite-type La_0.5Sr_0.5MnO₃. Among the Pd-loaded catalysts, however, Pd/La_0.8Sr_1.2MnO₄ showed the higher activity and the selectivity to N₂ than Pd/La_0.5Sr_0.5MnO₃ and Pd/γ-Al₂O₃. The excellent catalytic performance of Pd/La_0.2Sr_1.2MnO₄ could be ascribable to the formation of SrPd₃O₄ which was detected by XRD in the catalyst but not in the other two catalysts.     

Enhanced dielectric tunability properties of Ba(ZrxTi1−x)O3 thin films using seed layers on Pt/Ti/SiO2/Si substrates

The compositionally graded and homogeneous Ba(Zr_xTi_1−x)O₃ (BZT) thin films were fabricated on LaNiO₃ (LNO) buffered Pt/Ti/SiO₂/Si and Pt/Ti/SiO₂/Si substrates by a sol–gel deposition method, respectively. These films crystallized into a single perovskite phase. The BZT thin films deposited on LaNiO₃/Pt/Ti/SiO₂/Si substrates had a highly (1 0 0) preferred orientation and exhibited a preferred (1 1 0) orientation when the thin films were deposited on Pt/Ti/SiO₂/Si substrates. The LNO and Ba(Zr_0.30Ti_0.70) served as seed layer on Pt/Ti/SiO₂/Si substrates and analyze the relationship of seed layer, microstructure and dielectric behavior of the thin films. The compositionally graded thin films from BaTiO₃ to BaZr_0.35Ti_0.65O₃ were fabricated on LNO/Pt/Ti/SiO₂/Si substrates. The tunability behavior of compositionally graded films was analyzed in order to produce optimum effective dielectric properties. The dielectric constant of BaZr_xTi_1−xO₃ compositionally graded thin films showed weak temperature dependence. This kind of thin films has a potential in a fabrication of a temperature stable tunable device.     

Catalytic combustion of CH4 and CO on La1−xMxMnO3 perovskites

The activities of perovskites depend on compositions and preparation methods. Various perovskites, La_1−xM_xMnO₃ (M=Ag, Sr, Ce, La), have been prepared by two different methods (co-precipitation and spray decomposition). The new preparation method, spray decomposition, produced perovskites of a high surface area of over 10 m²/g. The catalytic activities for CH₄ and CO oxidation have been studied on a series of catalysts, La_1−xM_xMnO₃. The perovskite-type oxide, La_0.7Ag_0.3MnO₃, shows the highest catalytic activity: the complete conversion of CO and CH₄ at 370 and 825 K, respectively.     

Synthesis of CeO2–MnOx mixed oxides and catalytic performance under oxygen-rich condition

Ce_0.5Zr_0.5O₂, Ce_0.5Zr_0.2Mn_0.3O₂ and Ce_0.5Mn_0.5O₂ were prepared by citric acid sol–gel method. The effect of manganese on the structural and redox properties of ceria-based mixed oxides was investigated by means of powder X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller analyses, temperature-programmed reduction and catalytic activity evaluation in the presence of excess O₂. The results showed that some Mn cations could enter into the ceria lattice to form solid solutions. Mn₃O₄ appeared due to the instability of the mixed oxides with increment of the Mn doping ratio while another oxide Mn₂O₃ is detected in the physical mixture of ceria and manganese oxide. These Mn-doped mixed oxides, especially Ce_0.5Mn_0.5O₂, presented better catalytic activities than Ce_0.5Zr_0.5O₂ and even Pt-loaded catalyst for total oxidation of C₃H₈ and oxidative sorption of NO in the presence of excess oxygen. The oxidation ability of Mn and the strong interaction between Mn and Ce were suggested to promote the oxygen storage/transport capacity of the mixed oxides as well as reactive adsorption of nitric oxide and hydrocarbons.     

Development of new catalysts for N2O-decomposition from adipic acid plant

Direct decomposition of N₂O was investigated using simulated and real industrial gas stream coming from an adipic acid plant. Two different kinds of catalysts were studied: (i) LaB_1−xB′_xO₃ and CaB_1−xCu_xO₃ (B = Mn, Fe and B′ = Cu, Ni) perovskites (PVKs) and (ii) supported PVKs (10 or 20 wt.%) on γ-Al₂O₃ and CeO₂–ZrO₂. The structural modifications induced by the composition of PVK samples affect the catalytic performances: mixed oxide formation in CaMn_0.7Cu_0.3O₃ samples allows to reach the highest values of N₂O conversion while the effect of PVK phases is more controversial. The importance of copper on catalytic activities is confirmed by the investigation on CaMn_1−xCu_xO₃ samples. The best results were obtained with a CaMn_0.6Cu_0.4O₃ catalyst calcined at 700 °C for 5 h, in which the presence of copper maximises the Ca₃CuMnO₆ phase formation. The increase in Cu-content produces a large segregation of CuO despite PVK formation. The best catalyst was tested using industrial gas stream, showing good stability also in the presence of H₂O and O₂ (8% v/v ) after 1400 h on-stream. To increase surface area, Cu-containing PVKs were deposed on γ-Al₂O₃ and CeO₂–ZrO₂, and this latter has been recognised as the best support. Indeed, the activity of the PVKs supported on ceria–zirconia is comparable to and even better than that of the bulk catalysts. A possible explanation regards the support contribution in terms of activity and/or promotion of O₂ mobility which enhances the overall activity of the catalyst.     

AMnO3 (A=La, Nd, Sm) and Sm1−xSrxMnO3 perovskites as combustion catalysts: structural, redox and catalytic properties

Catalytic combustion of methane has been investigated over AMnO₃ (A = La, Nd, Sm) and Sm_1−xSr_xMnO₃ (x = 0.1, 0.3, 0.5) perovskites prepared by citrate method. The catalysts were characterized by chemical analysis, XRD and TPR techniques. Catalytic activity measurements were carried out with a fixed bed reactor at T = 623–1023 K, space velocity = 40 000 N cm³ g⁻¹ h⁻¹, CH₄ concentration = 0.4% v/v, O₂ concentration = 10% v/v.

Specific surface areas of perovskites were in the range 13–20 m² g⁻¹. XRD analysis showed that LaMnO₃, NdMnO₃, SmMnO₃ and Sm_1−xSr_xMnO₃ (x = 0.1) are single phase perovskite type oxides. Traces of Sm₂O₃ besides the perovskite phase were detected in the Sm_1−xSr_xMnO₃ catalysts for x = 0.3, 0.5. Chemical analysis gave evidence of the presence of a significant fraction of Mn(IV) in AMnO₃. The fraction of Mn(IV) in the Sm_1−xSr_xMnO₃ samples increased with x. TPR measurements on AMnO₃ showed that the perovskites were reduced in two steps at low and high temperature, related to Mn(IV) → Mn(III) and Mn(III) → Mn(II) reductions, respectively. The onset temperatures were in the order LaMnO₃ > NdMnO₃ > SmMnO₃. In Sm_1−xSr_xMnO₃ the Sr substitution for Sm caused the formation of Mn(IV) easily reducible to Mn(II) even at low temperature. Catalytic activity tests showed that all samples gave methane complete conversion with 100% selectivity to CO₂ below 1023 K. The activation energies of the AMnO₃ perovskites varied in the same order as the onset temperatures in TPR experiments suggesting that the catalytic activity is affected by the reducibility of manganese. Sr substitution for Sm in SmMnO₃ perovskites resulted in a reduction of activity with respect to the unsubstituted perovskite. This behaviour was related to the reduction of Mn(IV) to Mn(II), occurring under reaction conditions, hindering the redox mechanism.     

Methane combustion and CO oxidation on LaAl1−xMnxO3 perovskite-type oxide solid solutions

Structural, redox and catalytic deep oxidation properties of LaAl_1−xMn_xO₃ (x=0.0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8, 1.0) solid solutions prepared by the citrate method and calcined at 1073 K were investigated. XRD analysis showed that all the LaAl_1−xMn_xO₃ samples are single phase perovskite-type solid solutions. Particle sizes and surface areas (SA) are in the 280–1180 Å and 4–33 m² g⁻¹ ranges, respectively. Redox properties and the content of Mn⁴⁺ were derived from temperature programmed reduction (TPR) with H₂. Two reduction steps are observed by TPR for pure LaMnO₃, the first attributed to the reduction of Mn⁴⁺ to Mn³⁺ and the second due to complete reduction of Mn³⁺ to Mn²⁺. The presence of Al in the LaAl_1−xMn_xO₃ solid solutions produces a strong promoting effect on the Mn⁴⁺→Mn³⁺ reducibility and inhibits the further reduction to Mn²⁺. Both for methane combustion and CO oxidation all Mn-containing perovskites are much more active than LaAlO₃, so pointing to the essential role of the transition metal ion in developing highly active catalysts. Partial dilution with Al appears to enhance the specific activity of Mn sites for methane combustion.     

Oxidation of unsymmetrical dimethylhydrazine over heterogeneous catalysts Solution of environmental problems of production, storage and disposal of highly toxic rocket fuels

The catalytic oxidation of unsymmetrical dimethylhydrazine (UDMH) by air has been studied in a vibro-fluidized catalyst bed laboratory kinetic setup over catalysts Cu_xMg_1−xCr₂O₄/γ-Al₂O₃, 32.9%Ir/γ-Al₂O₃ and β-Si₃N₄ in a temperature range 150–400 °C. The catalyst Cu_xMg_1−xCr₂O₄/γ-Al₂O₃ was found to be optimal regarding high yields of CO₂ and low yields of NO_x. A probable mechanism of UDMH heterogeneous catalytic oxidation is proposed. Catalyst Cu_xMg_1−xCr₂O₄/γ-Al₂O₃ has been further used in the pilot plant specially designed for the destruction of UDMH. Results of testing the main fluidized bed catalytic reactor for UDMH oxidation and the reactor for selective catalytic reduction of NO_x with NH₃ are presented. These results prove that the developed UDMH destruction technology is highly efficient and environmentally safe.     

Performance and characterization of supported metal catalysts for complete oxidation of formaldehyde at low temperatures

Activities of a series of metals (Pt, Pd, Rh, Cu, Mn) supported on TiO₂ were investigated for the catalytic oxidation of formaldehyde. Among them, Pt/TiO₂ was found to be the most promising catalyst. Nitrogen adsorption, hydrogen chemisorption, X-ray diffraction (XRD), transmission electron microscopy (TEM) and temperature programmed reduction (TPR) by H₂ were used to characterize the platinum catalysts. Using Ce_0.8Zr_0.2O₂, Ce_0.2Zr_0.8O₂, SiO₂ as supports instead of TiO₂, the activity sequence of 0.6 wt.% platinum with respect to the supports is TiO₂ > SiO₂ > Ce_0.8Zr_0.2O₂ > Ce_0.2Zr_0.8O₂, and this appears to be correlated with the dispersion of platinum on supports rather than the specific surface areas of the catalysts. Platinum loading on TiO₂ has a great effect on the catalytic activity, and 0.6 wt.% Pt/TiO₂ catalyst was observed to be the most active, which could be attributed to the well-dispersed platinum surface phase. The reduction temperature greatly affects the particle size and, consequently, the catalytic activity. The smaller particle size of platinum, due to its high dispersion on support, has a positive effect on catalytic performance. Increasing formaldehyde concentration and space velocity exhibits an inhibiting effect on the catalytic activity.     

Synthesis of cyclic carbonates from epoxides: Use of reticular oxygen of Al2O3 or Al2O3-supported CeOx for the selective epoxidation of propene

Reticular oxygen of Al₂O₃ or CeO_x supported on Al₂O₃ was used for the epoxidation of propene without any double bond cleavage. In batch reaction, Al₂O₃ alone was able to convert propene into propene oxide (PO) with 100% selectivity and 2% conversion of propene with a close to 3:1 ratio with respect to the number of Al(III) reduced to elemental Al. When Ce₂O₃/Al₂O₃ or CeO₂/Al₂O₃ was used, Al remained in its +3 oxidation state, while the Ce oxide was the oxidant as demonstrated by XPS analyses. CeO_x/Al₂O₃ was more active (propene conversion yield of 4–5%) but the selectivity was lower (70%) as PO was isomerized into acetone and propionaldehyde.

Interestingly the use of reticular oxygen very much improves the selectivity with respect to the use of pure O₂. In fact, while propene was more efficiently oxidized (10%) with O₂ in presence of Al₂O₃ or CeO_x/Al₂O₃, the selectivity was as low as 40% because C1 and C2 products were formed. However, the use of reticular oxygen represents a selective two-step technique for the use of molecular oxygen as oxidant of propene. The used oxides can be re-oxidized and the whole process can be further improved towards higher yields.

PO is quantitatively converted into propene carbonate by reaction with CO₂ in presence of Nb₂O₅.     

Characterizations of platinum catalysts supported on Ce, Zr, Pr-oxides and formation of carbonate species in catalytic wet air oxidation of acetic acid

Catalytic wet air oxidation (CWAO) of aqueous solution of acetic acid (78 mmol L⁻¹) was carried out with pure oxygen (2 MPa) at 200 °C in a stirred batch reactor on platinum supported oxide catalysts (Pt/oxide, oxide = CeO₂, Zr_0.1Ce_0.9O₂, Zr_0.1(Ce_0.75Pr_0.25)_0.9O₂ and ZrO₂). Platinum was loaded on oxides by impregnation (5 wt%), and then the catalysts were reduced under H₂. Homogenous dispersions of 2–3 nm metal crystallites were obtained. The catalytic activity depended on the ability of the support to resist to the formation of carbonates. Ce(CO₃)OH species, determined by FT-IR and XRD, were rapidly formed during the CWAO reaction especially on mixed oxides. These carbonates were responsible to a drastic drop in catalytic performances. Amounts of carbonate species increase with the ability of the catalyst to transfer oxygen.