Super austenitic stainless steels — a promising replacement for the currently used type 316L stainless steel as the construction material for flue-gas desulphurization plant

Potentiodynamic anodic cyclic polarization experiments on type 316L stainless steel and 6Mo super austenitic stainless steels were carried out in simulated flue-gas desulphurization (FGD) environment in order to assess the localized corrosion resistance. The pitting corrosion resistance was higher in the case of the super austenitic stainless steel containing 6Mo and a higher amount of nitrogen. The pit-protection potential of these alloys was more noble than the corrosion potential, indicating the higher repassivation tendency of actively growing pits in these alloys. The accelerated leaching study conducted for the above alloys showed that the super austenitic stainless steels have a little tendency for leaching of metal ions such as iron, chromium and nickel at different impressed potentials. This may be due to surface segregation of nitrogen as CrN, which would, in turn, enrich a chromium and molybdenum mixed oxide film and thus impedes the release of metal ions. The present study indicates that the 6Mo super austenitics can be adopted as a promising replacement for the currently used type 316L stainless steel as the construction material for FGD plants.     

Dissolution behaviour of stainless steel weld metals during active potential range: A calculational approach

Uniform or localised corrosion resistance of stainless steels is attributed to the presence of a tenacious passive film formed on the surface, the thickness and chemical composition of which depends on the applied potential. The protective properties of such films depend on the bulk composition of the alloy, presence of secondary phases and elemental segregation. In this paper the role of Cr, Mo and ferrite content on the anodic dissolution behaviour of type 316 austenitic stainless steel weld metals has been investigated. A calculational approach was tried in order to qualitatively understand the behaviour of the stainless steel weld metals with different chemical compositions and heat inputs. Extensive iterative calculations were carried out by using the experimental data on the anodic current values to arrive at the results.     

Electrochemical and analytical investigation of passive films formed on stainless steels in alkaline media

Passive films were grown in potentiodynamic mode, by cyclic voltammetry on AISI 316 and AISI 304 stainless steels. The composition of these films was investigated by X-ray photoelectron spectroscopy (XPS). The electrochemical behaviour and the chemical composition of the passive films formed by cyclic voltammetry were compared to those of films grown under natural conditions (by immersion at open circuit potential, OCP) in alkaline solutions simulating concrete. The study included the effect of pH of the electrolyte and the effect of the presence of chloride ions.The XPS results revealed important changes in the passive film composition, which becomes enriched in chromium and depleted in magnetite as the pH decreases. On the other hand, the presence of chlorides promotes a more oxidised passive layer. The XPS results also showed relevant differences on the composition of the oxide layers for the films formed under cyclic voltammetry and/or under OCP.     

Mechanical and corrosion behaviour of powder metallurgy stainless steel based metal matrix composites

Abstract

Stainless steel matrix composites were manufactured using powder metallurgy techniques. Matrixes of AISI 316L stainless steel were reinforced with yttria or alumina particles. Chromium diboride was added in some cases and boron nitride in others to obtain steels with densities close to theoretical, using reactive (liquid phase) sintering techniques. The composites showed very good densification and better hardness than the 316L stainless steel without additions. The 316L steel reinforced with 4 wt-% yttria chromium diboride showed the highest density and strength, with an acceptable corrosion resistance.     

Synthesis of nanostructured zirconia electrodeposited films on AISI 316L stainless steel and its behaviour in corrosion resistance assessment

This work deals with the study of AISI 316L stainless steel samples coated with nanostructured zirconia thin films, using electrodeposition methods. The chemical composition and compounds formed were determined by X-ray photoelectron spectroscopy (XPS). The morphology of zirconia films was analysed by scanning electron microscopy (SEM) and atomic force microscopy (AFM).Corrosion resistance of the coated steel was tested in a chloride environment. XPS analysis results show zirconium element on the metal surface, bound to oxygen-forming zirconia. The anodic polarization curves obtained in Hank's solution show that zirconia coating can be used as protective coating against pitting corrosion of AISI 316L stainless steels.     

The effect of TiN inclusions and deformation-induced martensite on the corrosion properties of AISI 321 stainless steel

Stainless steel of type 321 is commonly used for the production of exhaust systems because of its temperature resistance and welding properties, which are better than those of AISI 304 or similar steels. AISI 321 is a titanium stabilized austenitic stainless steel, where this element is added to form carbides in order to avoid chromium impoverishment due to chromium carbide formation. Cold shaping can, in the case of austenitic stainless steel, cause the formation of deformation induced martensite, which can improve its mechanical properties, but unfortunately can also spoil its good resistance to corrosion. Titanium nitride inclusions are cathodic with respect to steels, and therefore cause their anodic dissolution. Martensite is, however, more susceptible to the corrosion than austenite in steels. The main aim of this study was to analyze the pitting corrosion and stress corrosion cracking which is initiated on prototype cold-formed outer exhaust sleeves during the testing of different cleaning procedures before chromium plating. Various microscopic methods were used to identify the initiation of corrosion and its propagation.     

The influence of complexing agent and proteins on the corrosion of stainless steels and their metal components

The present work is devoted to the problem of biodegradation of orthopaedic implants manufactured from stainless steel. In vitro simulations of the biocompatibility of two types of stainless steel, AISI 304 and AISI 316L, and their individual metal components, i.e. iron, chromium, nickel and molybdenum, were carried out in simulated physiological solution (Hank's) containing complexing agents. Knowledge of the effects of the chemical and biological complexing agents, EDTA and proteins, respectively, on the corrosion resistance of a metal should provide a better understanding of the processes occurring in vivo on its surface. The behavior of stainless steels and metal components was studied under open circuit and under potentiostatic conditions. The concentration of dissolved corrosion products in the form of released ions was determined by differential pulse polarography (DPP) and atomic emission spectrometry using inductively coupled plasma (ICP-AES). The composition of solid corrosion products formed on the surface was analyzed by energy dispersive X-ray spectroscopy (EDS) and their morphology was viewed by scanning electron microscopy (SEM). The addition of EDTA and proteins to physiological solution increased the dissolution of pure metals and stainless steels. The effect of particular protein differs on different metals and alloys.     

Corrosion susceptibilities of various metals and alloys in synthetic geothermal brines

The corrosion susceptibilities of various pure metals and alloys were investigated in synthetic geothermal fluids. Rates of corrosion of AISI 1010 steel, types 304 and 316 stainless steels, Monel 400 and nickel were determined at three temperatures (296, 333 and 368 K); and those of the molybdenum, niobium and titanium were determined at 368 K only. Type 304 stainless steel appears to undergo an active-passive transition at a temperature range between 333 and 368 K. In the passive state type 304 steel has essentially the same corrosion rate as type 316. At 368 K the corrosion rate of pure nickel was approximately 2.5 times that of Monel, which in turn was twice that of type 316 stainless steel. The corrosion rates of Mo, Nb and Ti were less than one mdd at the highest experimental temperature.     

Degradation of mechanical and corrosion resistance properties of AISI 317L steel exposed at 550 °C

The use of austenitic stainless steel type AISI 317L has increased in the last years, in substitution to AISI 316L and other austenitic grades. The higher Mo content (3.0 wt.%. at least) gives higher corrosion resistance to AISI 317L. However, some concern arises when this material is selected to high temperature process services in refineries. Microstructural changes such as chromium carbide precipitation and sigma phase formation may occur in prolonged exposure above 450 °C. In this work, the microstructure evolution of AISI 317L steel during aging at 550 °C was analyzed. Thermodynamic calculations with Thermocalc® and detailed microstructural analysis were performed in steel plate base metal and in weld metal produced by GTAW process. The aging for 200, 300 and 400 h promoted gradual embrittlement and deterioration of corrosion resistance of both weld and base metal. The results show that the selection of AISI 317L steel to services where temperatures can reach 550 °C is not recommended.     

Surface-protein interactions on different stainless steel grades: effects of protein adsorption, surface changes and metal release

Implantation using stainless steels (SS) is an example where an understanding of protein-induced metal release from SS is important when assessing potential toxicological risks. Here, the protein-induced metal release was investigated for austenitic (AISI 304, 310, and 316L), ferritic (AISI 430), and duplex (AISI 2205) grades in a phosphate buffered saline (PBS, pH 7.4) solution containing either bovine serum albumin (BSA) or lysozyme (LSZ). The results show that both BSA and LSZ induce a significant enrichment of chromium in the surface oxide of all stainless steel grades. Both proteins induced an enhanced extent of released iron, chromium, nickel and manganese, very significant in the case of BSA (up to 40-fold increase), whereas both proteins reduced the corrosion resistance of SS, with the reverse situation for iron metal (reduced corrosion rates and reduced metal release in the presence of proteins). A full monolayer coverage is necessary to induce the effects observed.     

高氮奥氏体不锈钢耐点蚀性能研究

目前产于高氮不锈钢的研究多集中于理论基础、制造工艺和力学性能等方面,有关耐蚀性方面的研究有限。通过循环极化、Mott-Schottky曲线以及电化学阻抗(EIS)等方法,研究了Cr23Mo1N奥氏体不锈钢(高氮钢,HNSS)和316L不锈钢在Cl-溶液中的耐点蚀性能。结果表明:与316L不锈钢相比,高氮钢具有更正的自腐蚀电位,更小的维钝电流密度。阻抗谱表明高氮钢的钝化膜比316L更加稳定,且电荷转移电阻更大。Mott-Schottky曲线表明高氮钢的点缺陷施主浓度比316L不锈钢低一个数量级,钝化膜的绝缘性更好。循环极化曲线表明高氮钢的点蚀敏感性更小,钝化膜的自修复能力更强,耐蚀性能更加优越。     

Resistance spot welding joints of AISI 316L austenitic stainless steel sheets: Phase transformations,mechanical properties and microstructure characterizations

In this paper, we aim to optimize welding parameters namely welding current and time in resistance spot welding (RSW) of the austenitic stainless steel sheets grade AISI 316L. Afterward, effect of optimum welding parameters on the resistance spot welding properties and microstructure of AISI 316L austenitic stainless steel sheets has been investigated. Effect of welding current at constant welding time was considered on the weld properties such as weld nugget size, tensile–shear load bearing capacity of welded materials, failure modes, failure energy, ductility, and microstructure of weld nuggets as well. Phase transformations that took place during weld thermal cycle were analyzed in more details including metallographic studies of welding of the austenitic stainless steels. Metallographic images, mechanical properties, electron microscopy photographs and micro-hardness measurements showed that the region between interfacial to pullout mode transition and expulsion limit is defined as the optimum welding condition. Backscattered electron scanning microscopic images (BE-SEM) showed various types of delta ferrite in weld nuggets. Three delta ferrite morphologies consist of skeletal, acicular and lathy delta ferrite morphologies formed in resistance spot welded regions as a result of non-equilibrium phases which can be attributed to the fast cooling rate in RSW process and consequently, prediction and explanation of the obtained morphologies based on Schaeffler, WRC-1992 and Pseudo-binary phase diagrams would be a difficult task.     

In vitro corrosion resistance of Lotus-type porous Ni-free stainless steels

The corrosion behavior of three kinds of austenitic high nitrogen Lotus-type porous Ni-free stainless steels was examined in acellular simulated body fluid solutions and compared with type AISI 316L stainless steel. The corrosion resistance was evaluated by electrochemical techniques, the analysis of released metal ions was performed by inductively coupled plasma mass spectrometry (ICP-MS) and the cytotoxicity was investigated in a culture of murine osteoblasts cells. Total immunity to localized corrosion in simulated body fluid (SBF) solutions was exhibited by Lotus-type porous Ni-free stainless steels, while Lotus-type porous AISI 316L showed very low pitting corrosion resistance evidenced by pitting corrosion at a very low breakdown potential. Additionally, Lotus-type porous Ni-free stainless steels showed a quite low metal ion release in SBF solutions. Furthermore, cell culture studies showed that the fabricated materials were non-cytotoxic to mouse osteoblasts cell line. On the basis of these results, it can be concluded that the investigated alloys are biocompatible and corrosion resistant and a promising material for biomedical applications.     

Zum Verhalten rost‐ und säurebeständiger Stähle unter Komplexbeanspruchung. Teil 1 Passivität und Lochkorrosionsbeständigkeit

Some Aspects on Corrosion Fatique of Stainless Steels. Part 1 Passivity and Pitting Corrosion Susceptibility Iron‐Chromium‐Nickel alloys are of special interest for many applications because of their excellent resistance to corrosion. The nature and composition of passive films formed on stainless steels depend on the prevailing conditions, viz. steel‐composition, passivation potential, aging, pH, electrolyt composition and temperature. Passive films may be damaged by local breakdown. At least two mechanisms are possible for this localisation: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Because of this, steels suffer a degradation of their fatique properties when exposed to an aqueous environment. Passivation of austenitic, ferritic‐austenitic and martensitic stainless steels has been studied in different solutions using electrochemical techniques. The results clarified that for two of the investigated alloys the prediction of fracture initiation based on pitting corrosion in chlorid containing solutions is possible. (To be continued.)     

Chemical composition and corrosion resistance of passive chromate films formed on stainless steels 316 L and 1.4301

The chemical composition and corrosion behavior of the natural and formed by chemical treatment in chromium-containing solution passive films on 316 L and 1.4301 stainless steel surfaces have been investigated by means of X-ray photoelectron spectroscopy and electrochemical in situ method of anodic polarization curves. It have been established that the oxide films formed by the chemical treatment have different chemical composition (Cr-enriched), color and reduced corrosion resistance compared to the natural passive films on both steels. The results have shown that the lower part of the oxide layer represents a uniform modified passive film and the upper one is a porous Cr³⁺-enriched film with an island-like structure. The latter permits a direct contact of the solution with the modified passive film which controls the corrosion resistance by the dissolution of the Fe³⁺ oxides present in the lower thinner layer.     

Microstructure-mechanical and chemical behavior relationships in passive thin films

The passive films play an important role in corrosion and stress corrosion cracking of austenitic stainless steels. The current research investigates the relationship between alloy chemistry, microstructure, and mechanical behavior of passive films formed on 316, 304, and 904L stainless steels (SS). X-ray photoelectron spectroscopy and transmission electron microscopy were used to investigate the effect of alloy chemistry and microstructure constituents on the thin film fracture properties determined by nanoindentation tests. The analyses showed that fracture loads are directly related to the crystallography of the thin films. It was found that decreasing the ratio of iron to other metallic elements in the film led to an increase in the load required to fracture the film. It was also found that films grown on 304, 316, and 904L stainless steels were the cubic polymorph of Cr₂O₃, rather than the lower energy rhombohedral form. In the case of 904L SS the film formed as an epitaxial layer. In the other two cases it consisted of small crystalline islands in an amorphous matrix. A dichromate treatment of 316 SS decreased the iron content in the oxide film and increased the hardness. It also resulted in an epitaxial film.     

Deep cryogenic treatment of AISI 302 stainless steel: Part II – Fatigue and corrosion

During the last decade, the interest about deep cryogenic treatment (DCT) is grown beyond its successful application on tool steels. The use of such cold treatment has shown positive effects on carburized steel fatigue life and some promising results were also noticed on stainless steels and on other materials. In this article, the DCT effects on fatigue and corrosion resistance of the AISI 302 austenitic stainless steel are analysed starting from the results of an extensive experimental campaign that was performed on both hardened and solubilized material conditions. The analysis includes an evaluation of the influence that the most important treatment parameters have on the final result. Considering their statistical significance at different reliability levels, the results show that the DCT can improve the fatigue behaviour of the solubilized AISI 302, while no important changes are noticed on the hardened material. Moreover, no difference was detected on the corrosion resistance of the cryotreated material, ensuring that such key-property for this class of steel is not compromised by the cryogenic treatment.     

铸造双相不锈钢点腐蚀行为研究

采用化学浸泡腐蚀试验及微观组织和化学成分分析研究了5种铸造双相不锈钢在6%Fe Cl3溶液中的点腐蚀行为,并与316L奥氏体不锈钢进行了对比。结果表明,铸造双相不锈钢的抗点腐蚀性能均优于316L的,腐蚀速率和点腐蚀深度均小于316L奥氏体不锈钢的;双相不锈钢主要耐点蚀能力合金元素在奥氏体和铁素体相内分布不均匀,铬、钼更多地分配于铁素体相内,而镍、氮则更多地分配于奥氏体相内,铁素体相的耐点蚀指数PRE(Cr%+3.3Mo%+16N%)大于奥氏体相;双相不锈钢的耐点腐蚀性能与化学成分有关,随着PRE的增加,双相不锈钢的耐点腐蚀性能提高,铜元素在铁素体内析出的富铜相导致点蚀优先在铁素体内发生和发展。     

Modifying the properties of AISI 316L steel by glow discharge assisted low-temperature nitriding and oxynitriding

Apart from titanium, its alloys and CoCrMo alloys, austenitic steels are widely used in medical applications. In order to improve the frictional wear resistance of these steels, they are subjected to various surface treatments such that the good corrosion resistance of the steels is preserved.The paper analyzes the structure and phase composition of AISI 316L steel after subjecting it to low-temperature nitriding and oxynitriding under glow discharge conditions. The treatments produced diffusion-type surface layers composed of nitrogen-expanded austenite (known as the phase S, i.e. supersaturated solution of nitrogen in austenite) with a thin surface layer of chromium nitride (CrN) zone (after nitriding) or chromium oxide (Cr₂O₃) zone (after oxynitriding). It has been shown that the treatments substantially increase the hardness and frictional wear resistance of the steel without degrading its good corrosion resistance (examined in the Ringer physiological solution at a temperature of 37 °C).     

A review on nickel-free nitrogen containing austenitic stainless steels for biomedical applications

The field of biomaterials has become a vital area, as these materials can enhance the quality and longevity of human life. Metallic materials are often used as biomaterials to replace structural components of the human body. Stainless steels, cobalt–chromium alloys, commercially pure titanium and its alloys are typical metallic biomaterials that are being used for implant devices. Stainless steels have been widely used as biomaterials because of their very low cost as compared to other metallic materials, good mechanical and corrosion resistant properties and adequate biocompatibility. However, the adverse effects of nickel ions being released into the human body have promoted the development of “nickel-free nitrogen containing austenitic stainless steels” for medical applications. Nitrogen not only replaces nickel for austenitic structure stability but also much improves steel properties. Here we review the harmful effects associated with nickel and emphatically the advantages of nitrogen in stainless steel, as well as the development of nickel-free nitrogen containing stainless steels for medical applications. By combining the benefits of stable austenitic structure, high strength, better corrosion and wear resistance and superior biocompatibility in comparison to the currently used austenitic stainless steel (e.g. 316L), the newly developed nickel-free high nitrogen austenitic stainless steel is a reliable substitute for the conventionally used medical stainless steels.