Rational Design of Small Molecular Donor for Solution‐Processed Organic Photovoltaics with 8.1% Efficiency and High Fill Factor via Multiple Fluorine Substituents and Thiophene Bridge

A series of tetrafluorine‐substituted small molecules with a D₁‐A‐D₂‐A‐D₁ linear framework based on indacenodithiophene and difluorobenzothiadiazole is designed and synthesized for application as donor materials in solution‐processed small‐molecule organic solar cells. The impacts of thiophene π‐bridge and multiple fluorinated modules on the photophysical properties, the energy levels of the highest occupied molecular orbitals (HOMO) and lowest unoccupied molecular orbitals (LUMO), charge carrier mobility, the morphologies of blend films, and their photovoltaic properties as electron donor material in the photoactive layer are investigated. By incorporating multiple fluorine substituents of benzothiadiazole and inserting two thiophene spacers, the fill factor (FF), open‐circuit voltage, and short‐circuit current density are dramatically improved in comparison with fluorinated‐free materials. With the solvent vapor annealing treatment, further enhancement in charge carrier mobility and power conversion efficiency (PCE) are achieved. Finally, a high PCE of 8.1% with very‐high FF of 0.76 for BIT‐4F‐ T/PC₇₁BM is achieved without additional additive, which is among one of the highest reported for small‐molecules‐based solar cells with PCE over 8%. The results reported here clearly indicate that high PCE in solar cells based small molecules can be significantly increased through careful engineering of the molecular structure and optimization on the morphology of blend films by solvent vapor annealing.     

A Highly Crystalline Fused‐Ring n‐Type Small Molecule for Non‐Fullerene Acceptor Based Organic Solar Cells and Field‐Effect Transistors

N‐type organic small molecules (SMs) are attracting attention in the organic electronics field, due to their easy purification procedures with high yield. However, only a few reports show SMs that perform well in both organic field‐effect transistors (OFETs) and organic solar cells (OSCs). Here, the synthesis and characterization of an n‐type small molecule with an indacenodithieno[3,2‐b]thiophene (IDTT) core unit and linear alkylated side chain (C₁₆) (IDTTIC) are reported. Compared to the state‐of‐the‐art n‐type molecule IDTIC, IDTTIC exhibits smaller optical bandgap and higher absorption coefficient, which is due to the enhanced intramolecular effect. After mixing with the polymer donor PBDB‐T, IDTIC‐based solar cells deliver a power conversion efficiency of only 5.67%. In stark contrast, the OSC performance of IDTTIC improves significantly to 11.2%. It is found that the superior photovoltaic properties of PBDB‐T:IDTTIC blends are mainly due to reduced trap‐assisted recombination and enhanced molecular packing coherence length and higher domain purity when compared to IDTIC. Moreover, a significantly higher electron mobility of 0.50 cm² V⁻¹ s⁻¹ for IDTTIC in OFET devices than for IDTIC (0.15 cm² V⁻¹ s⁻¹) is obtained. These superior performances in OSCs and OFETs demonstrate that SMs with extended π‐conjugation of the backbone possess a great potential for application in organic electronic devices.     

Self‐Doping Fullerene Electrolyte‐Based Electron Transport Layer for All‐Room‐Temperature‐Processed High‐Performance Flexible Polymer Solar Cells

To achieve high‐performance large‐area flexible polymer solar cells (PSCs), one of the challenges is to develop new interface materials that possess a thermal‐annealing‐free process and thickness‐insensitive photovoltaic properties. Here, an n‐type self‐doping fullerene electrolyte, named PCBB‐3N‐3I, is developed as electron transporting layer (ETL) for the application in PSCs. PCBB‐3N‐3I ETL can be processed at room temperature, and shows excellent orthogonal solvent processability, substantially improved conductivity, and appropriate energy levels. PCBB‐3N‐3I ETL also functions as light‐harvesting acceptor in a bilayer solar cell, contributing to the overall device performance. As a result, the PCBB‐3N‐3I ETL‐based inverted PSCs with a PTB7‐Th:PC₇₁BM photoactive layer demonstrate an enhanced power conversion efficiency (PCE) of 10.62% for rigid and 10.04% for flexible devices. Moreover, the device avoids a thermal annealing process and the photovoltaic properties are insensitive to the thickness of PCBB‐3N‐3I ETL, yielding a PCE of 9.32% for the device with thick PCBB‐3N‐3I ETL (61 nm). To the best of one's knowledge, the above performance yields the highest efficiencies for the flexible PSCs and thick ETL‐based PSCs reported so far. Importantly, the flexible PSCs with PCBB‐3N‐3I ETL also show robust bending durability that could pave the way for the future development of high‐performance flexible solar cells.     

Highly Efficient Inverted Organic Solar Cells Through Material and Interfacial Engineering of Indacenodithieno[3,2‐b]thiophene‐Based Polymers and Devices

A synergistic approach combining new material design and interfacial engineering of devices is adopted to produce high efficiency inverted solar cells. Two new polymers, based on an indacenodithieno[3,2‐b]thiophene‐difluorobenzothiadiazole (PIDTT‐DFBT) donor–acceptor (D–A) polymer, are produced by incorporating either an alkyl thiophene (PIDTT‐DFBT‐T) or alkyl thieno[3,2‐b]thiophene (PIDTT‐DFBT‐TT) π‐bridge as spacer. Although the PIDTT‐DFBT‐TT polymer exhibits decreased absorption at longer wavelengths and increased absorption at higher energy wavelengths, it shows higher power conversion efficiencies in devices. In contrast, the thiophene bridged PIDTT‐DFBT‐T shows a similar change in its absorption spectrum, but its low molecular weight leads to reduced hole mobilities and performance in photovoltaic cells. Inverted solar cells based on PIDTT‐DFBT‐TT are explored by modifying the electron‐transporting ZnO layer with a fullerene self‐assembled monolayer and the MoO₃ hole‐transporting layer with graphene oxide. This leads to power conversion efficiencies as high as 7.3% in inverted cells. PIDTT‐DFBT‐TT's characteristic strong short wavelength absorption and high efficiency suggests it is a good candidate as a wide band gap material for tandem solar cells.     

Synthesis and Characterization of New Thieno[3,4‐c]pyrrole‐4,6‐dione Derivatives for Photovoltaic Applications

A new class of low‐bandgap copolymers based on benzodithiophene (BDT) and thieno[3,4‐c]pyrrole‐4,6‐dione (TPD) units is reported. Chemical modifications of the conjugated backbone promote both high molecular weights and processability while allowing for tuning of the electronic properties. Copolymers with substituted thiophene spacers (alkyl chains facing the BDT unit) or unsubstituted thiophene spacers tend to have low power conversion efficiencies (PCE less than 1%) due to a bad morphology of the active layer, whereas copolymers with substituted thiophene spacers (alkyl chains facing TPD unit) show enhanced morphology and PCEs up to of 3.9%. Finally, BDT‐TPD copolymers without any thiophene spacers still show the best performances with power conversion efficiencies up to 5.2%.     

“Solvent Annealing” Effect in Polymer Solar Cells Based on Poly(3‐hexylthiophene) and Methanofullerenes

The self‐organization of the polymer in solar cells based on regioregular poly(3‐hexylthiophene) (RR‐P3HT):[6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) is studied systematically as a function of the spin‐coating time t_s (varied from 20–80 s), which controls the solvent annealing time t_a, the time taken by the solvent to dry after the spin‐coating process. These blend films are characterized by photoluminescence spectroscopy, UV‐vis absorption spectroscopy, atomic force microscopy, and grazing incidence X‐ray diffraction (GIXRD) measurements. The results indicate that the π‐conjugated structure of RR‐P3HT in the films is optimally developed when t_a is greater than 1 min (t_s ～ 50 s). For t _s < 50 s, both the short‐circuit current (J_SC) and the power conversion efficiency (PCE) of the corresponding polymer solar cells show a plateau region, whereas for 50 < t_s < 55 s, the J_SC and PCE values are significantly decreased, suggesting that there is a major change in the ordering of the polymer in this time window. The PCE decreases from 3.6 % for a film with a highly ordered π‐conjugated structure of RR‐P3HT to 1.2 % for a less‐ordered film. GIXRD results confirm the change in the ordering of the polymer. In particular, the incident photon‐to‐electron conversion efficiency spectrum of the less‐ordered solar cell shows a clear loss in both the overall magnitude and the long‐wavelength response. The solvent annealing effect is also studied for devices with different concentrations of PCBM (PCBM concentrations ranging from 25 to 67 wt %). Under “solvent annealing” conditions, the polymer is seen to be ordered even at 67 wt % PCBM loading. The open‐circuit voltage (V_OC) is also affected by the ordering of the polymer and the PCBM loading in the active layer.     

A Timely Synthetic Tailoring of Biaxially Extended Thienylenevinylene‐Like Polymers for Systematic Investigation on Field‐Effect Transistors

Considering there is growing interest in the superior charge transport in the (E)‐2‐(2‐(thiophen‐2‐yl)‐vinyl)thiophene (TVT)‐based polymer family, an essential step forward is to provide a deep and comprehensive understanding of the structure–property relationships with their polymer analogs. Herein, a carefully chosen set of DPP‐TVT‐n polymers are reported here, involving TVT and diketopyrrolopyrrole (DPP) units that are constructed in combination with varying thiophene content in the repeat units, where n is the number of thiophene spacer units. Their OFET characteristics demonstrate ambipolar behavior; in particular, with DPP‐TVT‐0 a nearly balanced hole and electron transport are observed. Interestingly, the majority of the charge‐transport properties changed from ambipolar to p‐type dominant, together with the enhanced hole mobilities, as the electron‐donating thiophene spacers are introduced. Although both the lamellar d‐spacings and π‐stacking distances of DPP‐TVT‐n decreased with as the number of thiophene spacers increased, DPP‐TVT‐1 clearly shows the highest hole mobility (up to 2.96 cm² V^?1 s^?1) owing to the unique structural conformations derived from its smaller paracrystalline distortion parameter and narrower plane distribution relative to the others. These in‐depth studies should uncover the underlying structure–property relationships in a relevant class of TVT‐like semiconductors, shedding light on the future design of top‐performing semiconducting polymers.     

Conjugated Small Molecule for Efficient Hole Transport in High‐Performance p‐i‐n Type Perovskite Solar Cells

The π‐conjugated organic small molecule 4,4′‐cyclohexylidenebis[N,N‐bis(4‐methylphenyl) benzenamine] (TAPC) has been explored as an efficient hole transport material to replace poly(3,4‐ethylenedio‐xythiophene):poly(styrenesulfonate) (PEDOT:PSS) in the preparation of p‐i‐n type CH₃NH₃PbI₃ perovskite solar cells. Smooth, uniform, and hydrophobic TAPC hole transport layers can be facilely deposited through solution casting without the need for any dopants. The power conversion efficiency of perovskite solar cells shows very weak TAPC layer thickness dependence across the range from 5 to 90 nm. Thermal annealing enables improved hole conductivity and efficient charge transport through an increase in TAPC crystallinity. The perovskite photoactive layer cast onto thermally annealed TAPC displays large grains and low residual PbI₂, leading to a high charge recombination resistance. After optimization, a stabilized power conversion efficiency of 18.80% is achieved with marginal hysteresis, much higher than the value of 12.90% achieved using PEDOT:PSS. The TAPC‐based devices also demonstrate superior stability compared with the PEDOT:PSS‐based devices when stored in ambient circumstances, with a relatively high humidity ranging from 50 to 85%.     

Layer‐by‐Layer Conjugated Extension of a Semiconducting Polymer for High‐Performance Organic Field‐Effect Transistor

A donor–acceptor (D–A) semiconducting copolymer, PDPP‐TVT‐29, comprising a diketopyrrolopyrrole (DPP) derivative with long, linear, space‐separated alkyl side‐chains and thiophene vinylene thiophene (TVT) for organic field‐effect transistors (OFETs) can form highly π‐conjugated structures with an edge‐on molecular orientation in an as‐spun film. In particular, the layer‐like conjugated film morphologies can be developed via short‐term thermal annealing above 150 °C for 10 min. The strong intermolecular interaction, originating from the fused DPP and D–A interaction, leads to the spontaneous self‐assembly of polymer chains within close proximity (with π‐overlap distance of 3.55 Å) and forms unexpectedly long‐range π‐conjugation, which is favorable for both intra‐ and intermolecular charge transport. Unlike intergranular nanorods in the as‐spun film, well‐conjugated layers in the 200 °C‐annealed film can yield more efficient charge‐transport pathways. The granular morphology of the as‐spun PDPP‐TVT‐29 film produces a field‐effect mobility (μ _FET) of 1.39 cm² V^?1 s^?1 in an OFET based on a polymer‐treated SiO₂ dielectric, while the 27‐Å‐step layered morphology in the 200 °C‐annealed films shows high μ _FET values of up to 3.7 cm² V^?1 s^?1.     

Synthesis,Characterization, and Field‐Effect Transistor Performance of Thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene Derivatives

The synthesis, characterization, and field‐effect transistor (FET) properties of a new class of thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene derivatives are described. The optical spectra of their films show the presence of stronger interactions between molecules in the solid state. Thermal analyses reveal that the three materials are thermally stable and have no phase transitions at low temperature. The crystal structures are determined, and show π‐stacked structures and intermolecular S···S contacts. These organic materials exhibit p‐type FET behavior with hole mobilities as high as 0.14 cm² V^?1 s^?1 and an on/off current ratio of 10⁶. These results indicate that thieno[3,2‐b]thieno [2′,3′:4,5]thieno[2,3‐d]thiophene, as a linear π‐conjugated system, is an effective building block for developing high‐performance organic semiconductors.     

Solution‐Processed High‐Performance Tetrathienothiophene‐Based Small Molecular Blends for Ambipolar Charge Transport

Four soluble dialkylated tetrathienoacene ( TTAR) ‐based small molecular semiconductors featuring the combination of a TTAR central core, π‐conjugated spacers comprising bithiophene ( bT ) or thiophene ( T ), and with/without cyanoacrylate ( CA ) end‐capping moieties are synthesized and characterized. The molecule DbT‐TTAR exhibits a promising hole mobility up to 0.36 cm² V^?1 s^?1 due to the enhanced crystallinity of the microribbon‐like films. Binary blends of the p‐type DbT‐TTAR and the n‐type dicyanomethylene substituted dithienothiophene‐quinoid ( DTTQ‐11 ) are investigated in terms of film morphology, microstructure, and organic field‐effect transistor (OFET) performance. The data indicate that as the DbT‐TTAR content in the blend film increases, the charge transport characteristics vary from unipolar (electron‐only) to ambipolar and then back to unipolar (hole‐only). With a 1:1 weight ratio of DbT‐TTAR DTTQ‐11 in the blend, well‐defined pathways for both charge carriers are achieved and resulted in ambipolar transport with high hole and electron mobilities of 0.83 and 0.37 cm² V^?1 s^?1, respectively. This study provides a viable way for tuning microstructure and charge carrier transport in small molecules and their blends to achieve high‐performance solution‐processable OFETs.     

Monitoring the Formation of a CH3NH3PbI3–xClx Perovskite during Thermal Annealing Using X‐Ray Scattering

Grazing incidence wide and small angle X‐ray scattering (GIWAXS and GISAXS) measurements have been used to study the crystallization kinetics of the organolead halide perovskite CH₃NH₃PbI_3–xCl_x during thermal annealing. In situ GIWAXS measurements recorded during annealing are used to characterize and quantify the transition from a crystalline precursor to the perovskite structure. In situ GISAXS measurements indicate an evolution of crystallite sizes during annealing, with the number of crystallites having sizes between 30 and 400 nm increasing through the annealing process. Using ex situ scanning electron microscopy, this evolution in length scales is confirmed and a concurrent increase in film surface coverage is observed, a parameter crucial for efficient solar cell performance. A series of photovoltaic devices are then fabricated in which perovskite films have been annealed for different times, and variations in device performance are explained on the basis of X‐ray scattering measurements.     

Plastic Solar Cells

Recent developments in conjugated‐polymer‐based photovoltaic elements are reviewed. The photophysics of such photoactive devices is based on the photo‐induced charge transfer from donor‐type semiconducting conjugated polymers to acceptor‐type conjugated polymers or acceptor molecules such as Buckminsterfullerene, C₆₀. This photo‐induced charge transfer is reversible, ultrafast (within 100 fs) with a quantum efficiency approaching unity, and the charge‐separated state is metastable (up to milliseconds at 80 K). Being similar to the first steps in natural photosynthesis, this photo‐induced electron transfer leads to a number of potentially interesting applications, which include sensitization of the photoconductivity and photovoltaic phenomena. Examples of photovoltaic architectures are presented and their potential in terrestrial solar energy conversion discussed. Recent progress in the realization of improved photovoltaic elements with 3 % power conversion efficiency is reported.     

Donor and Acceptor Unit Sequences Influence Material Performance in Benzo[1,2‐b:4,5‐b′]dithiophene–6,7‐Difluoroquinoxaline Small Molecule Donors for BHJ Solar Cells

Well‐defined small molecule (SM) donors can be used as alternatives to π‐conjugated polymers in bulk‐heterojunction (BHJ) solar cells with fullerene acceptors (e.g., PC₆₁/₇₁BM). Taking advantage of their synthetic tunability, combinations of various donor and acceptor motifs can lead to a wide range of optical, electronic, and self‐assembling properties that, in turn, may impact material performance in BHJ solar cells. In this report, it is shown that changing the sequence of donor and acceptor units along the π‐extended backbone of benzo[1,2‐b:4,5‐b′]dithiophene–6,7‐difluoroquinoxaline SM donors critically impacts (i) molecular packing, (ii) propensity to order and preferential aggregate orientations in thin‐films, and (iii) charge transport in BHJ solar cells. In these systems ( SM1‐3 ), it is found that 6,7‐difluoroquinoxaline ([2F]Q) motifs directly appended to the central benzo[1,2‐b:4,5‐b′]dithiophene (BDT) unit yield a lower‐bandgap analogue ( SM1 ) with favorable molecular packing and aggregation patterns in thin films, and optimized BHJ solar cell efficiencies of ≈6.6%. ¹H‐¹H DQ‐SQ NMR analyses indicate that SM1 and its counterpart with [2F]Q motifs substituted as end‐group SM3 possess distinct self‐assembly patterns, correlating with the significant charge transport and BHJ device efficiency differences observed for the two analogous SM donors (avg. 6.3% vs 2.0%, respectively).     

Efficient Polymer Solar Cells Based on Poly(3‐hexylthiophene):Indene‐C70 Bisadduct with a MoO3 Buffer Layer

Polymer solar cells (PSCs) with poly(3‐hexylthiophene) (P3HT) as a donor, an indene‐C₇₀ bisadduct (IC₇₀BA) as an acceptor, a layer of indium tin oxide modified by MoO₃ as a positive electrode, and Ca/Al as a negative electrode are presented. The photovoltaic performance of the PSCs was optimized by controlling spin‐coating time (solvent annealing time) and thermal annealing, and the effect of the spin‐coating times on absorption spectra, X‐ray diffraction patterns, and transmission electron microscopy images of P3HT/IC₇₀BA blend films were systematically investigated. Optimized PSCs were obtained from P3HT/IC₇₀BA (1:1, w/w), which exhibited a high power conversion efficiency of 6.68%. The excellent performance of the PSCs is attributed to the higher crystallinity of P3HT and better a donor–acceptor interpenetrating network of the active layer prepared under the optimized conditions. In addition, PSCs with a poly(3,4‐ethylenedioxy‐thiophene):poly(styrenesulfonate) (PEDOT:PSS) buffer layer under the same optimized conditions showed a PCE of 6.20%. The results indicate that the MoO₃ buffer layer in the PSCs based on P3HT/IC₇₀BA is superior to that of the PEDOT:PSS buffer layer, not only showing a higher device stability but also resulting in a better photovoltaic performance of the PSCs.     

Manipulating backbone structure with various conjugated spacers to enhance photovoltaic performance of D–A-type two-dimensional copolymers

A class of low band-gap two-dimensional conjugated polymers of PBDTT-FQ, PBDTT-TQ, PBDTT-BTQ and PBDTT-TTQ was designed and synthesized, which contains the same di(alkylthiophene)-substituted benzo[1,2-b:4,5-b′]dithiophene (BDTT) and 6,7-difluoroquinoxaline (Q) units, as well as various conjugated spacers of furan, thiophene, bithiophene and thieno[3,2-b]thiophene in the main chain. Significant effect of the varied spacers between the BDTT and Q units on the thermal, optical, electrochemical and photovoltaic properties was investigated and observed for these two-dimensional copolymers in the polymer solar cells. The maximum power conversion efficiency of 5.9% with a short circuit current of 13.7 mA/cm² and a fill factor of 0.56 was obtained for the PBDTT-TQ with thiophene spacer in the bulk hetero-junction PSCs using [6,6]-phenyl-C₇₁-butyric acid methyl ester as acceptor.     

Enhancement in Organic Photovoltaic Efficiency through the Synergistic Interplay of Molecular Donor Hydrogen Bonding and π‐Stacking

For organic photovoltaic (OPV) cells based on the bulk heterojunction (BHJ) structure, it remains challenging to rationally control the degree of phase separation and percolation within blends of donors and acceptors to secure optimal charge separation and transport. Reported is a bottom‐up, supramolecular approach to BHJ OPVs wherein tailored hydrogen bonding (H‐bonding) interactions between π‐conjugated electron donor molecules encourage formation of vertically aligned donor π‐stacks while simultaneously suppressing lateral aggregation; the programmed arrangement facilitates fine mixing with fullerene acceptors and efficient charge transport. The approach is illustrated using conventional linear or branched quaterthiophene donor chromophores outfitted with terminal functional groups that are either capable or incapable of self‐complementary H‐bonding. When applied to OPVs, the H‐bond capable donors yield a twofold enhancement in power conversion efficiency relative to the comparator systems, with a maximum external quantum efficiency of 64%. H‐bond promoted assembly results in redshifted absorption (in neat films and donor:C₆₀ blends) and enhanced charge collection efficiency despite disparate donor chromophore structure. Both features positively impact photocurrent and fill factor in OPV devices. Film structural characterization by atomic force microscopy, transmission electron microscopy, and grazing incidence wide angle X‐ray scattering reveals a synergistic interplay of lateral H‐bonding interactions and vertical π‐stacking for directing the favorable morphology of the BHJ.     

Acceptor‐Substituted S,N‐Heteropentacenes of Different Conjugation Length: Structure–Property Relationships and Solar Cell Performance

The synthesis, optoelectronic, and photovoltaic properties of novel acceptor–donor–acceptor (A–D–A) based π‐conjugated functional molecules 1 – 3, comprising a planar S,N‐heteropentacene as central donor substituted with various terminal acceptor units, such as 1,1‐dicyanovinylene (DCV) and 1‐(1,1‐dicyanomethylene)‐cyclohex‐2‐ene (DCC), are reported. The structural variation of the end groups provides molecules 1 – 3 with gradually increased π‐conjugation due to a rising number of double bonds, which comes from the DCC unit(s). From optoelectronic investigation, structure–property relationships are deduced and the novel A–D–A heteropentacenes 1 – 3 are implemented as photoactive donor component in solution‐processed bulk heterojunction solar cells together with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor. The structural variation in the S,N‐heteropentacenes leads to clear trends in the photovoltaic performance and power conversion efficiencies of up to 4.9% are achieved. Furthermore, due to extension of the double bonds a clear trade‐off between the open circuit voltage (V _OC) and the short circuit current density (J _SC) values is observed. The role of additives on the optimization of the nanoscale morphology and device performance is investigated. The findings presented herein demonstrate that depending on the types of materials the additive may have significantly different effects on the active layer morphology and the device performance.     

Significant Improvement of Dye‐Sensitized Solar Cell Performance by Small Structural Modification in π‐Conjugated Donor–Acceptor Dyes

Two donor‐π‐acceptor (D‐π‐A) dyes are synthesized for application in dye‐sensitized solar cells (DSSC). These D‐π‐A sensitizers use triphenylamine as donor, oligothiophene as both donor and π‐bridge, and benzothiadiazole (BTDA)/cyanoacrylic acid as acceptor that can be anchored to the TiO₂ surface. Tuning of the optical and electrochemical properties is observed by the insertion of a phenyl ring between the BTDA and cyanoacrylic acid acceptor units. Density functional theory (DFT) calculations of these sensitizers provide further insight into the molecular geometry and the impact of the additional phenyl group on the photophysical and photovoltaic performance. These dyes are investigated as sensitizers in liquid‐electrolyte‐based dye‐sensitized solar cells. The insertion of an additional phenyl ring shows significant influence on the solar cells' performance leading to an over 6.5 times higher efficiency (η = 8.21%) in DSSCs compared to the sensitizer without phenyl unit (η = 1.24%). Photophysical investigations reveal that the insertion of the phenyl ring blocks the back electron transfer of the charge separated state, thus slowing down recombination processes by over 5 times, while maintaining efficient electron injection from the excited dye into the TiO₂‐photoanode.     

The Relation Between Open‐Circuit Voltage and the Onset of Photocurrent Generation by Charge‐Transfer Absorption in Polymer : Fullerene Bulk Heterojunction Solar Cells

Photocurrent generation by charge‐transfer (CT) absorption is detected in a range of conjugated polymer–[6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) based solar cells. The low intensity CT absorption bands are observed using a highly sensitive measurement of the external quantum efficiency (EQE) spectrum by means of Fourier‐transform photocurrent spectroscopy (FTPS). The presence of these CT bands implies the formation of weak ground‐state charge‐transfer complexes in the studied polymer–fullerene blends. The effective band gap (E_g) of the material blends used in these photovoltaic devices is determined from the energetic onset of the photocurrent generated by CT absorption. It is shown that for all devices, under various preparation conditions, the open‐circuit voltage (V_oc) scales linearly with E_g. The redshift of the CT band upon thermal annealing of regioregular poly(3‐hexylthiophene):PCBM and thermal aging of poly(phenylenevinylene)(PPV):PCBM photovoltaic devices correlates with the observed drop in open‐circuit voltage of high‐temperature treated versus untreated devices. Increasing the weight fraction of PCBM also results in a redshift of E_g, proportional with the observed changes in V_oc for different PPV:PCBM ratios. As E_g corresponds with the effective bandgap of the material blends, a measurement of the EQE spectrum by FTPS allows us to measure this energy directly on photovoltaic devices, and makes it a valuable technique in the study of organic bulk heterojunction solar cells.