首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
《Materials & Design》2005,26(6):508-516
Due to their higher welding speed, automation and weld pool protection against to the atmosphere gases, gas metal arc welding (GMAW) process is widely used in industry. Due to the less stable arc associated with the use of consumable electrodes, GMAW process is not clean as good as gas tungsten arc welding process. Furthermore, the greater arc length in GMAW process also reduces the protective effect of the shielding gas. Due to electrochemical and thermochemical reactions between weld pool and arc atmosphere, it is quite important, especially weld metal toughness and joining of reactive materials to entirely create inert atmosphere for GMAW process. Therefore, a controlled atmosphere cabinet was developed for GMAW process. Low carbon steel combinations were welded with classical GMAW process in argon atmosphere as well as controlled atmosphere cabinet by using similar welding parameters. The mechanical and metallurgical properties of both weldments were evaluated. Result shows that toughness of the weld metal that was obtained in the controlled atmosphere cabinet much higher than that of classical GMAW process. The metallographic examination also clarified that there was not any gas porosity and inclusion in the weld metal compared with classical process.  相似文献   

2.
It is of great significance to determine the critical transition current from globular transfer to spray transfer in gas metal arc welding (GMAW) because metal transfer modes affect the weld quality and welding productivity. In this study, a simple model is developed to calculate the critical transition current based on the analysis of various forces exerted on a pendent droplet at the electrode tip. It is found that the force exerted by the incoming molten metal from the wire on the drop, i.e., the term c v c, plays an important role in determining the critical transition current. For mild steel wires and argon shielding gas, the critical transition current is predicted with different levels of wire diameter and extensions. The calculated results match the experimental ones.  相似文献   

3.
In the gas metal arc welding (GMAW) process, when the welding speed reaches a certain threshold, there will be an onset of weld bead undercut defects which limit the further increase of the welding speed. Establishing a mathematical model for high-speed GMAW to predict the tendency of bead undercuts is of great significance to prevent such defects. Under the action of various forces, the transferred metal from filler wire to the weld pool, and the geometry and dimension of the pool itself decide if the bead undercut occurs or not. The previous model simplified the pool shape too much. In this paper, based on the actual weld pool geometry and dimension calculated from a numerical model, a hydrostatic model for liquid metal surface is used to study the onset of bead undercut defects in the high-speed welding process and the effects of different welding parameters on the bead undercut tendency.  相似文献   

4.
Achieving an effective utilization and exploitation of TIG welding arcs require a thorough understanding of the plasma properties and its physical processes.Through simultaneous solutions of the set of conservation equations for mass,momentum, energy and current, a mathematical model has been developed to predict the velocity,temperature,and current density distributions in argon welding arcs.The predicted temperature fields in arc regions, and the distribution of current density and heat flux at the anode agree well with measurements reported in literatures.This work could lay the foundation for developing a comprehensive model of the TIG welding process where a dynamic, two-way coupling between the welding arc and the weld pool surface is properly represented.  相似文献   

5.
Abstract

Dissimilar metal welds (DMW’s) between ferritic and austenitic materials at elevated temperatures have concerned boiler manufacturers and operators for decades because of the proven potential for premature failure. The industry has desired an improved filler metal that would minimize or eliminate DMW failures and, with the current trend toward higher boiler steam pressures and temperatures, have suitable creep strength for joining higher strength materials such as Grade 91 steels After years of research, the Electric Power Research Institute (EPRI) concluded the development and commercialization of a nickel-based filler metal, EPRI P87, for application in shielded metal arc welding (SMAW). This work describes the subsequent development of an EPRI P87 solid wire welding product for application in gas tungsten arc and gas metal arc welding (GTAW and GMAW) processes, and the initial research into the performance of DMWs produced with the new solid wire P87 product. A 135 kg heat of solid wire was produced and tested using various welding processes and evaluation methods to ensure that the material would meet required weldability and design specifications. Welding methods included GMAW-P, GTAW and hot-wire GTAW in welds up to 50mm in thickness. The weld joint tested was a dissimilar metal weld of grade 91 to 347H, which was assessed using microstructure evaluation, creep testing, hot tensile testing, circular patch, and edge build-up investigations to examine hot-cracking susceptibility. This paper summarizes the research completed to date on the EPRI 87 filler wire which supports the acceptability of this material for its intended use in high-temperature power generation applications.  相似文献   

6.
Mechanism of Metal Transfer in DE-GMAW   总被引:1,自引:0,他引:1  
Modification of conventional gas metal arc welding (GMAW) process is of great potential to achieve high productivity with low cost and strong usability.Double-Electrode GMAW (DE-GMAW) is such a modified arc welding process which is formed by adding a bypass torch (gas tungsten arc welding torch) to a conventional GMAW system.The mechanism of metal transfer in DE-GMAW was proposed and verified in this paper.Experiments show that the critical current is decreased so that spray transfer can be obtained at a lower current level in DE-GMAW.Analysis of this significant change in metal transfer phenomena is conducted, and explanation is given out.It is found that the bypass arc in DE-GMAW lifts the anode point on the droplets such that the electromagnetic force becomes larger and squeezes the droplets so that spray transfer can take place under welding current lower than that in conventional GMAW.  相似文献   

7.
It is of great significance to determine the critical transition current from globular transfer to spray transfer in gas metal arc welding (GMAW) because metal transfer modes affect the weld quality and welding productivity. In this study, a simple model is developed to calculate the critical transition current based on the analysis of various forces exerted on a pendent droplet at the electrode tip. It is found that the force exerted by the incoming molten metal from the wire on the drop, i.e., the term Graphic相似文献   

8.
In the gas metal arc welding (GMAW) process, when the welding speed reaches a certain threshold, there will be an onset of weld bead undercut defects which limit the further increase of the welding speed. Establishing a mathematical model for high-speedGMAWto predict the tendency of bead undercuts is of great significance to prevent such defects. Under the action of various forces, the transferred metal from filler wire to the weld pool, and the geometry and dimension of the pool itself decide if the bead undercut occurs or not. The previous model simplified the pool shape too much. In this paper, based on the actual weld pool geometry and dimension calculated from a numerical model, a hydrostatic model for liquid metal surface is used to study the onset of bead undercut defects in the high-speed welding process and the effects of different welding parameters on the bead undercut tendency.  相似文献   

9.
It is of great significance to obtain a thorough understanding of the physical mechanisms responsible for humping bead phenomenon in high speed gas metal arc welding (GMAW) in order to raise welding efficiency. Experiments were conducted to observe the weld pool behaviors in high speed GMAW, and it was found that both the severely deformed weld pool surface and strong backward flowing play a dominant role in humping bead formation. In this study, a mathematical model is developed to quantitatively analyze the forming mechanism of humping beads for high speed GMAW through considering both the momentum and heat content distribution of the backward flowing molten metal inside the weld pool. The transient development of temperature profiles in the weld pool with severe deformation demonstrates the humping bead forming process under some welding conditions. The predicted and measured humping bead dimensions are in agreement.  相似文献   

10.
Robust sensing of arc length   总被引:4,自引:0,他引:4  
During arc welding, the arc heats and melts the workpiece as heat flux. When the welding current is given, the distribution and the intensity of the heat flux are determined by the length of the are. The measurement and control of the are length are fundamental in robotic and automated welding operations. Length of welding arc determines the distribution of the arc energy and thus the heat input and width of the weld. This work aims at improving the measurement accuracy of arc length using the spectrum of are light at a particular wavelength during gas tungsten arc welding (GTAW) with argon shield. To this end, effects of welding parameters on spectral distributions were studied. To verify the effects of base metal and arc length, the arc column was also sampled horizontally as Layers for spectral analysis. Results show that spectral lines of argon atoms are determined by are length, independent of welding parameters other than the current. Based on these findings, a compact arc light sensor has been designed to measure the arc length with adequate accuracy. A closed-loop arc length control system has been developed with the proposed sensor  相似文献   

11.
Double shielded gas tungsten arc welding (GTAW, also known as tungsten inert gas (TIG) welding) of an SUS304 stainless steel with pure inert argon as the inner layer shielding and the Ar-CO2 or CO2 active gas as the out layer shielding was proposed in this study to investigate its effect on the tungsten electrode protection and the weld shape variation. The experimental results showed that the inner inert argon gas can successfully prevent the outer layer active gas from contacting and oxidizing the tungsten electrode during the welding process. Active gas, carbon dioxide, in the outer layer shielding is decomposed in the arc and dissolves in the liquid pool, which effectively adjusts the active element, oxygen, content in the weld metal. When the weld metal oxygen content is over 70×10-6, the surface-tension induced Marangoni convection changes from outward into inward, and the weld shape varies from a wide shallow one to a narrow deep one. The effect of the inner layer gas flow rate on the weld bead morphology and the weld shape was investigated systematically. The results show that when the flow rate of the inner argon shielding gas is too low, the weld bead is easily oxidized and the weld shape is wide and shallow. A heavy continuous oxide layer on the liquid pool is a barrier to the liquid pool movement.  相似文献   

12.
The present investigation aims to study the effect of welding processes such as shielded metal arc welding (SMAW), gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW) on fatigue crack growth behaviour of the ferritic stainless steel (FSS) conforming to AISI 409M grade. Rolled plates of 4 mm thickness were used as the base material and AISI 2209 grade duplex stainless steel (DSS) was used as filler metal, for preparing single pass butt welded joints. Centre cracked tensile (CCT) specimens were used to evaluate the fatigue crack growth behaviour. From this investigation, it is found that the GTAW joints showed superior fatigue crack growth resistance compared with SMAW and GMAW joints. The reasons for the superior performance were discussed in detail.  相似文献   

13.
Gas metal arc welding (GMAW) develops an arc by controlling the metal from the wire rod and the input process parameters. The deposited metal forms a weld bead and themechanical properties depend upon the quality of the weld bead. Proper control of the process parameters which affect the bead geometry, the microstructures of the weldments and the mechanical properties like hardness, is necessary. This experimental study aims at developing mathematical models for bead height (HB), bead width (WB) and bead penetration (PB) and investigating the effects of four process parameters
viz: welding voltage, welding speed, wire feed rate and gas flow rate on bead geometry, hardness and microstructure of AISI321 steel with 10 mm thickness. The transient thermal analysis shows temperature and residual stress distributions at different conduction and convection conditions.  相似文献   

14.
黄勇  赵文强  张利尧 《材料导报》2017,31(22):70-74
提出了一种新型活性焊接方法——粉末熔池耦合活性TIG焊(Powder pool coupled activating TIG welding,PPCATIG)。该方法采用双层气体进行焊接,内层利用惰性气体保护钨极,外层通过自动送粉装置将活性剂粉末随保护气体送入电弧-熔池区域,增加熔深,提高焊接效率,实现机械化自动化焊接。针对SUS304不锈钢进行了直流正接PPCA-TIG表面熔深,通过与传统TIG焊对比,研究了SiO_2活性剂对电弧形态、焊缝成形、组织和力学性能的影响。结果表明:SiO_2能使电弧等离子体收缩、熔池金属流态改变,并且焊缝熔深能达到传统TIG焊的3倍以上,焊接效率明显提高。焊缝组织主要为奥氏体和铁素体,铁素体形态以骨架状为主。焊缝抗拉强度略低于母材,但相比传统TIG焊,焊缝屈服强度略有提高,其焊缝低温冲击韧性达到了传统TIG焊的96.8%,表现出了良好的力学性能。同时,采用该方法可有效避免活性剂粉末对钨极的污染。  相似文献   

15.
Abstract

The effect of process variables such as current, voltage, electrode extension, electrode diameter, etc., on the electrode melting and plate melting efficiencies of submerged arc welding (SAW) and gas metal arc welding (GMAW) has been studied. It has been shown that there is an increase in the electrode extension or a decrease in the voltage and electrode diameter. For the same welding parameters, the electrode melting efficiency is higher when the electrode is negative. A similar relationship was observed for GMAW. The results also indicated that the shielding gas in GMAW also had an effect on the electrode melting efficiency. The plate melting efficiency of GMAW increases with an increase in the welding current, voltage, and electrode diameter, and decreases with an increase in the electrode extension. For the same welding parameters, the plate melting efficiency is lower when the electrode is negative. For SAW there is an increase in the plate melting efficiency with an increase in the welding current and voltage. It was also observed that the plate melting efficiency was lower for the negative electrode. Although there was an indication of a decrease in the plate melting compared with similar effects in GMAHI: this decrease in plate melting efficiency did not seem significant. An attempt attempt has also been made to develop numerical models to predict the electrode and plate melting efficiencies from the process variables.

MST/1096  相似文献   

16.
The characteristics of a CO2-shielded arc are studied to evaluate its potential as a novel heat source for material processing, with lower costs and higher productivity than that of the tungsten–inert gas (TIG) arc. A double-gas-shielded system, using both CO2 and an inert gas, is employed for the arc torch; this minimizes consumption of the tungsten electrode and gives arc stability equivalent to an argon TIG arc for 1800 s operation. The arc voltage of the CO2-shielded arc is about 19 V for an arc current of 150 A and an arc gap of 3 mm, which is much higher than the 12 V obtained for an argon TIG arc. The CO2 constricts the arc, resulting in an increase in the maximum heat flux density at the anode surface by a factor of about 10 relative to the TIG arc. The penetration depth of stainless steel melted by the CO2-shielded arc is much larger than that for the argon TIG arc. It is concluded that the greater heating power of the CO2-shielded arc, which is due to the greater arc constriction, in turn a consequence of the greater specific heat of CO2, should lead to a large increase in material processing productivity.  相似文献   

17.
The weld pool geometry and its dimension in the globular-transfer mode during gas metal arc welding (GMAW) were numerically analyzed by using the thermal conduction model, which considered the influence of the deformation of weld pool surface on heat flow in the quasi-steady state. According to the features of the globular-transfer mode, the additional heat energy from molten metal droplets was treated as a plane or volumetric heat source term to correspond to different welding conditions. The weld pool surface profile was predicted while considering the effect of droplet impingement on the depression of the weld pool. The bead-on-plate GMAW experiments were performed under different welding conditions to validate the model of numerical analysis. It has been found that the predicted results agree well with the measured ones.  相似文献   

18.
In the present investigation, multi-pass gas metal arc welding (GMAW) of SA516 Gr70 carbon steel was carried out by different filler wires such as solid, metal cored and flux cored, wherein, other process parameters were kept constant. The hybrid approach of multi-pass filler wires was applied to obtain three different welds. The root pass was filled by a solid wire for all three cases while the subsequent filler pass was applied through solid, flux-cored and metal cored filler wires, respectively. Metallographic, mechanical and metallurgical analyses such as macrograph study, optical microscopy, tensile testing and hardness variations were performed to address the quality of weld. The results revealed that defect-free sound welds were produced by the hybrid approach of different filler wires in multi-pass GMAW. Overall cost and time reduction can be achieved through hybrid filler welds, without affecting their mechanical strength. Angular distortion was reported minimum at hybrid weld of solid and metal cored filler wire. Maximum reinforcement with higher penetration was observed at weld of solid and metal cored filler wire. Impact toughness was reported higher in case of hybrid weld of solid and flux cored filler wire. Higher macro hardness was reported at weld of solid and flux cored filler wire.  相似文献   

19.
A new high-efficiency method for welding thick plates of low-alloy high-tensile steel which does not require back chipping – double-sided arc welding (DSAW) – is provided in this paper. Backing run adopts double-sided pulse gas tungsten arc welding, and other passes adopt double-sided gas metal arc welding. Three-dimensional numerical models of DSAW with 50 mm plates are developed to predict the stress distribution by using finite-element analysis, computer parallel processing technology and multiple jobs design, and are compared with single arc welding (SAW). The analysis of the interpass stresses indicates that the stresses of the back and cover pass are to be regarded as the key point in multipass welding. To verify the calculated results, the residual stresses and transient temperature of back run weld measured individually agree approximately with the calculated results, which illustrates that the backing run and residual stresses of DSAW are lower than those of SAW.  相似文献   

20.
Finite element analysis of GTAW arc under different shielding gases   总被引:1,自引:0,他引:1  
The aim of this work is to use COMSOL software as a tool for solving the 2-D Magnetohydrodynamics (MHD) problem in the Gas Tungsten Arc Welding (GTAW) arc under the shielding gases argon, helium, nitrogen and argon + 10% hydrogen. COMSOL 3.5a worked perfectly for solving multiphysics phenomena, including the Navier-Stokes flow equation, the heat transfer equation and the Maxwell Equation. COMSOL software can be utilized to simulate the temperature and velocity profile in the GTAW arc after some validation procedures. Cumbersome experimental work can be avoided by using this numerical instrument.For our study, we compared the numerically calculated temperature profile and maximum plasma velocity under argon shielding gas and maximum temperature of a nitrogen arc with experimental results found in the literature. We also compared the numerically calculated velocity profile with another numerical solution found in the literature. Our comparisons showed good agreement. The highest temperature was in the nitrogen arc, while the highest voltage was in the helium arc. The highest total energy was in the helium arc similar to the voltage value. The highest plasma velocity values were obtained in the nitrogen and helium arcs. The most constricted arc was calculated in the nitrogen arc.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号