连铸坯实测反问题热弹黏塑性建模与分析

为了研究连铸板坯的传热和力学特征,通过建立考虑蠕变的铸坯热弹黏塑性全尺寸有限元数值模型,以实测温度和传热反问题获得的热流为依据,计算和探讨了结晶器内铸坯的传热、应力和应变行为。结果表明,弯月面下100 ~ 200 mm铸坯表面承受拉应力,宽面距角部40 ~ 90 mm的偏角部区域温度较高,坯壳厚度也较薄,距角部约400 mm处温度相对较低,收缩量及应力应变较大。窄面近角部区域的应力和应变总体上低于宽面,距角部越近,窄面铸坯表面的应变越高。偏角部区域坯壳厚度、应力、应变的非均匀性及存在的过大差异,是探讨近角部裂纹成因需要考虑的重要因素。     

提高亚包晶钢板坯拉速对结晶器传热的影响

通过对提高亚包晶钢AQ钢种230 mm×1200 mm板坯拉速试验过程中结晶器冷却水参数、铜板测温等数据进行适时记录,并与数学模型及ANSYS商业软件相结合,研究了提高拉速对结晶器平均热流、局部热流、铜板温度场以及坯壳厚度的影响。结果表明,拉速由1.3m/min提高到1.5m/min时,平均热流增加0.1 MW/m²左右,宽边弯月面区域局部热流增加0.13 MW/m²,但均在合理范围内,这与采用高碱度高结晶温度的试验保护渣有关;结晶器窄/宽面平均热流比超过0.9,应适当减少结晶器锥度;宽面坯壳厚度平均减薄4 mm左右,应严格控制结晶器传热强度,以保证连铸工艺稳定和铸坯质量。     

连铸结晶器内大方坯的热力耦合分析

针对攀钢大方坯连铸机投产初期铸坯表面角部纵裂缺陷,建立了大方坯连铸结晶器内铜板与铸坯问的热力耦合模型,应用模型分析了大方坯连铸结晶器内的传热过程和坯壳的应力分布.在传热模型中,以稳态模型分析结晶器的传热过程,以瞬态模型分析铸坯的传热过程;在力学模型中,考虑铸坯和结晶器的接触边界以处理结晶器角部的气隙,以热弹塑性模型分析铸坯的变形和应力场.2种结构的连铸结晶器中大方坯温度场和应力场计算结果表明,结晶器倒角从25 mm×45°变为12 mm×45°时,可改善铸坯角部的传热条件,降低凝固坯壳角部温度,增加凝固坯壳厚度,有利于减轻和防止铸坯角部裂纹.     

宽厚板坯连铸结晶器流场、温度场及应力场的耦合数值模拟

利用Pro CAST软件对2400 mm×400 mm宽厚板坯结晶器建立三维动态模型,采用移动边界法实现结晶器内流场、温度场及应力场的耦合模拟.结果表明:考虑凝固坯壳的影响,下回流区位置向铸坯中心靠拢,真实反映了钢液在连铸结晶器内的流动情况.自由液面的钢液从窄面流向水口,速度先增大后减小,距水口约0.7 m处,出现最大表面流速,约为0.21 m·s^-1.结晶器出口坯壳窄面中心厚度最小且由中心向两侧逐渐增大,最小厚度约为10.4 mm;受流股冲击影响较弱的宽面坯壳与窄面相比生长更均匀,宽面偏角部和中心的坯壳厚度分别为18.9 mm和27.6 mm.铸坯坯壳应力变化趋势与温度基本保持一致,表明初凝坯壳应力主要是热应力.结晶器内铸坯宽窄面上的等效应力均沿着结晶器高度下降方向呈增大趋势,铸坯角部、宽面中心及窄面中心位置的最大应力各约为200、100和25 MPa.     

方坯结晶器多锥度分析

基于坯壳应力遗传特性建立铸坯热力耦合模型,利用ANSYS对结晶器内铸坯进行铸坯传热及应力分析。依据最小气隙原则对结晶器锥度进行优化,分析了单锥度和多锥度对坯壳凝固行为的影响。结果表明:采用两种锥度形式的结晶器,铸坯角部凝固行为存在明显差异,而表面中心区域基本一致。单锥度结晶器内气隙分布较广,角部热流明显降低,在偏离角部12～22 mm处存在"热点"。多锥度结晶器内气隙宽度和存在范围显著减少,"热点"消失,多锥度结晶器更符合坯壳凝固收缩规律。     

结晶器磨损对铸坯传热的影响

基于坯壳应力遗传特性建立铸坯热力耦合模型,利用ANSYS对结晶器内铸坯传热及应力进行数值模拟,对比分析结晶器磨损前后坯壳厚度、表面温度和气隙分布规律。结果表明:结晶器在磨损之后,偏离角部附近形成"热点"区域。气隙分布范围由距角部10 mm扩展到80 mm,最大厚度由0.1 mm增加到1.2 mm。     

方坯表面纵裂的数值模拟研究

针对ER80-G钢165 mm×165 mm方坯纵裂问题,基于连铸坯壳应力遗传特性,采用有限元软件ANSYS建立二维方坯热力耦合分析模型,对结晶器锥度进行了优化分析。结果表明:原结晶器锥度小,导致"热点"区域坯壳生长减缓;保护渣转折温度高,加剧了气隙影响。原结晶器角部区域最大气隙1.46 mm,坯壳表面温度最高差值130℃,"热点"区域比表面中心坯壳厚度减薄1.5 mm。通过锥度优化消除了热点现象,结晶器出口处距角部15 mm区域坯壳厚度由12.3 mm增加到19 mm;同时将保护渣转折温度由1 200℃调整到了1 050～1 100℃,促进坯壳与结晶器之间的润滑,裂纹发生率由2%下降到0.46%。     

基于MiLE法模拟结晶器中大方坯温度场、应力场及流场

应用混合Langrangian和Eulerian法(MiLE)实现了结晶器中GCr15钢大方坯温度场、应力场及流场的动态模拟,模拟结果与实际生产铸坯吻合.铸坯坯壳角部的温度高于中部,铸坯表面从上到下的温度总体呈下降趋势,且等温区间与流场变化具有一定的相似性.铸坯坯壳中部厚度约为17.5 mm,角部厚度约为13.2 mm.凝固坯壳内的应力主要是热应力.坯壳出结晶器时,坯壳外表面处于压缩状态,凝固前沿为完全拉伸状态.有效应变从铸坯外表面到凝固前沿逐渐增大.钢液在前进过程中不断扩张,流速不断降低,当流股到达一定深度后,形成左右对称向上的两个回流,和一对由凝固面一侧向下而由中心向上流动的回流区.     

301不锈钢板坯结晶器出口热力耦合数学模型

针对某厂301不锈钢连铸坯表面裂纹缺陷发生率高的生产问题,建立了301不锈钢板坯连铸结晶器内凝固坯壳形成及应力和变形的热力耦合模型。该模型考虑了包晶钢高温相变特征及其结晶器内的凝固特点。利用有限元软件ANSYS,采用三维瞬态热传导有限元、生死单元技术及三维热弹塑性接触有限元算法进行求解,对301不锈钢板坯结晶器内凝固过程进行了研究。结果表明,结晶器出口处铸坯宽面中心温度最低,距角部40 mm处温度最高,坯壳最薄,随δ-Fe转变量增加,出口处坯壳温度升高,坯壳厚度变薄。铸坯宽面中心位移变形最小,角部最大,窄面位移量大于宽面。随δ-Fe转变量增加,出口处应力水平下降,热点区附近成裂指数增加,发生纹裂机率增大。     

气隙对连铸坯应力分布影响的有限元数值模拟

建立了结晶器内连铸坯热弹塑性应力有限元数学模型。在热弹塑性本构方程中考虑了材料力学性能、屈服函数随温度和应变速率的变化。着重研究了气隙对坯壳应力分布的影响。研究结果表明：当坯壳角部有明显的气隙形成时,铸坯偏角区成为热节区。在此热节区内,坯壳受到拉应力的作用,连铸坯有产生皮下裂纹的可能     

转炉炉壳热应力分析

根据实际转炉建立实体模型。以有限元为手段,考虑了炉衬和炉壳材料的物性参数随温度变化的特点和炉衬与炉壳之间膨胀间隙,计算了转炉炉壳在温度载荷和炉衬膨胀压力同时作用下的热应力。所得结果可为转炉炉壳设计提供依据。     

焦炭热性能指标意义浅析

通过对焦炭在高炉内的历程及其变化规律的剖析,阐述焦炭热性能指标的意义,形象地把焦炭在高炉内的损耗分为三部分(M1,M2,M3)。指出M2对焦比及焦炭价格有一定的指导作用。     

Results of treatment of cancer of the cardia

Cancer of the cardia is traditionally discussed with cardiac cancer of the lower portion of the esophagus and upper gastric cancer invading the esophagus, and the specific characteristics of cancer of the cardia have never been clearly defined. We reviewed the outcome of 172 patients with adenocarcinoma of the cardia who had undergone radical surgery between 1949 and 1994 in the Division of Gastrointestinal Surgery of the Cancer Institute Hospital. The centers of the tumors were located within 2 cm above and below the boundary between the esophagus and the stomach, and their longitudinal diameter was less than 8 cm. We divided the patients into an early period (1949-1979; n = 79) and a late period (1980-1994; n = 93), and focused on the historical transition. There were no differences in patient gender or histology between the two periods. However, the late period was associated with fewer cases of esophageal invasion and shorter longitudinal diameter, as the age of the population advanced. The number of advanced cancers such as the localized and infiltrative type had decreased, and early cancer and early clinical stage had become more common, but despite the fact that the number of early cancers had increased, extended dissection, such as thoracic and paraaortic lymph node dissection, was performed more frequently. By clinical stage, the long-term outcome markedly improved in Stage I patient in the late period, and tended to improve in Stage II and III patients. This appears to have been attributable to the prevention of micrometastasis by extended dissection, although the number of early cancers is another major potential cause. There were no differences in the outcome of Stage IV patients between the two periods, and further advances in multimodality therapy must be awaited. The range of resection is basically proximal gastrectomy, and if there are adequate indications, the prognosis is favorable. In view of the status of lymphatic flow and lymph node metastasis, and long-term results, lateroaortic lymph node dissection is important. Since the number of early cancer patients has been increasing, if intraabdominal recurrence is prevented, intrathoracic lymph node dissection will contribute greatly to the outcome of such patients.     

The effect of amount of possession of the trait of hostility on accuracy of perception of hostility in others.

Some theories of personality hold that an individual's perception of others is influenced by his own personality characteristics; more specifically, that a trait of low social value will be projected more into others, and that insight into the possession of these characteristics reduces this distortion. These 2 hypotheses were tested by having a group of college students rate each other (including themselves) on degree of friendliness or hostility. Agreement with group rating about self yielded the insight score. In general, the hypotheses were supported; the "friendly" Ss were most accurate in their perception of others, and insight was positively associated with accurate perception. From Psyc Abstracts 36:04:4HL16M. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Effect of antibiotics of chemotaxis of human leukocytes

The effect of 20 different antibiotics on chemotaxis by human neutrophils was studied. Human leukocytes incubated with chloramphenicol, rifampin, sodium fusidate, and tetracyclines in vitro showed markedly depressed migration. The mechanisms by which these antibiotics affect leukotaxis are discussed.     

Quality of life of relatives of mental patients

Usage of quality of life of psychiatric patients' relatives as the parameter of estimation of the quality of psychiatric care is considered. By means of standard questionnaire elaborated by the authors as well as by means of both individual and group conversations the quality of life was analyzed in 40 relatives which lived together with psychiatric patients. Different spheres of their life and difficulties (financial, social-psychologic, production) were examined in families with such patients. The defects of psychiatric care that had direct influence on the quality of life of the psychiatric patients' relatives are outlined.