共查询到18条相似文献,搜索用时 109 毫秒
1.
2.
通过同时采用API620-2002和API650-2007,对设计压力为-2.1~21kPa的自支撑式拱顶储罐的设计计算分析,对该储罐的罐壁、罐顶、抗压圈及锚固的设计进行重点介绍,为低压储罐及类似设计压力的储罐设计计算做一个指引。 相似文献
3.
4.
5.
6.
本文以8000m3储罐设计为例,对大型储罐顶、底、壁的设计及制造方面进行探讨.同时,分别技API650,GB50341和SH3046三种规范进行设计,分析了它们之间的差异. 相似文献
7.
8.
9.
10.
11.
以1.0×10<'3>m<'3>、1.5×10<'5>m<'3>、2.0×10<'5>m<'3>的原油储罐罐壁厚度设计为例,说明GB 50341计算出的厚度过于先进,许用应力的选取值得商榷;SH 3046标准又过于保守;API 650计算结果与实测的应力水平较为接近,因此,在大型油罐设计时建议优先选择API 650作为... 相似文献
12.
13.
In this article, a genetic algorithm is used to optimize the separator pressures in a multistage crude oil and multistage gas condensate production unit with four and three separators respectively. This leads to the generation of more accurate results for the quality and quantity of oil remaining in the stock tank for both crude oil and gas condensate production units. Genetic-based optimized pressures for crude oil separators resulted in 1.8% and 2% enhancement in oil remaining in the stock tank for summer and winter respectively. API gravity of the stock tank oil was improved 2.4% in summer and 2.2% in winter. For the gas condensate production unit, optimized pressures can enhance by 8.6% and 8.1% the oil remaining in the stock tank for summer and winter respectively. The API gravity of stock tank liquid also increased by 2.6% for both summer and winter. 相似文献
14.
简述了防止储罐内部发生超压事故的技术措施;介绍了美国石油化工协会标准——API中关于储罐遭遇火焰时必须紧急泄放相应气量的计算方法;阐述了目前国内外普遍采用的紧急泄放装置的结构形式和选用方法;以实例计算了储罐顶部紧急泄放人孔的规格尺寸和数量。 相似文献
15.
根据API 581基于风险的检验(RBI)原理,进行常压储罐定量RBI研究,建立储罐壁板和底板的失效可能性、失效后果与风险等级的分析方法.通过此方法,可针对储罐不同的失效可能性等级和风险等级制定相应的检验策略,达到降低风险的目的,确保长周期安全运行. 相似文献
16.
针对常压储罐管理中出现的问题,编制基于风险的B/S模式常压储罐管理系统,实现了常压储罐的风险评价,并将风险评价与设备管理无缝对接,计算出储罐的风险等级,对储罐的日常管理工作具有指导意义. 相似文献
17.
以某原油输送中泄压罐泄压设施为例,采用API国际标准,简述原油紧急泄放装置瞬间泄放的计算方法以及设计中原油泄压罐的泄压流量最大面积与储罐顶面积的比值选定。 相似文献