Enhancement of recycled aggregate properties by accelerated CO2 curing coupled with limewater soaking process

Strengthening the attached old cement mortar of recycled concrete aggregate (RCA) is a common approach to enhance the RCA properties. Accelerated CO₂ curing has been regarded as an alternative way to enhance the properties of RA. However, the improvement of the properties of RCA was limited by the shortage of reactive components in the old cement mortar available for the carbonation reactions. In this study, a CO₂ curing process associated with a limewater saturation method was performed cyclically on cement mortar samples, aiming to enhance the properties of cement mortars via artificially introducing additional calcium into the pores of the cement mortars. The results indicated that the adopted treatment method promoted the level of carbonation which was demonstrated by higher CO₂ uptake by the limewater saturated cement mortar when compared to that without limewater treatment. After 3-cycles of limewater-CO₂ treatment, the density of the cement mortar slightly increased by 5.7%, while the water absorption decreased by over a half. For mechanical properties, the compressive and flexural strength were increased by 22.8% and 42.4%, respectively. Compared to the untreated cement mortar samples, the total porosity of cement mortar was reduced by approximately 33% and the densified microstructure therefore resulted in a higher microhardness.     

Performance of Portland limestone cements in mortar prisms immersed in sulfate solutions at 5 °C

The results of a test programme to investigate the sulfate resistance of mortars, immersed up to 12 months at 5 °C in magnesium sulfate and sodium sulfate solutions, is described. The mortars were prepared from four cements; a Portland cement, a sulfate-resisting Portland cement and two Portland limestone cements containing 15% by mass of an oolitic limestone and a carboniferous limestone. The mortar specimens were subject to BS 5328 Class 4A and 4B sulfate exposure conditions. These are the highest classes for concretes prepared using sulfate-resisting Portland cement (SRPC) before surface protection is required and are two and three classes higher than those recommended for concretes prepared using Portland cement (PC) and Portland limestone cement (PLC), respectively. Two free water-cement ratios were used, 0.5 and 0.75. Performance was monitored by visual assessment, expansion and changes in flexural and compressive strengths.At a free water-cement ratio of 0.75, the PC mortars and PLC mortars exhibited visually very severe attack with the former showing expansion and reductions in strength, and the latter mainly reductions in strength. At a free water-cement ratio of 0.50 both the PC mortars and PLC mortars showed slight/moderate to severe visual attack, the degree of deterioration appearing slightly greater in the PLC mortars, more especially those made with oolitic limestone. The PLC mortars also exhibited reductions in compressive failure load. The SRPC mortars exhibited little visual deterioration, no expansion, a small increase in flexural strength and no significant reductions in compressive strength. At a free water-cement ratio of 0.75 substantial amounts of thaumasite, together with ettringite was present in the surface layers of the deteriorated PLC mortars whilst ettringite was present in the surface layers of the deteriorated PC mortars. It is concluded that mortars made with a PC with a C₃A content of about 10% by mass were broadly similar in their vulnerability to sulfate attack at 5 °C as PLC mortars containing 15% limestone by mass, although the mode of attack was different.     

Compressive strength and drying shrinkage of fly ash-bottom ash-silica fume multi-blended cement mortars

This paper studies the physical properties, compressive strength and drying shrinkage of multi-blended cement under different curing methods. Fly ash, ground bottom ash and undensified silica fume were used to replace part of cement up to 50% by weight. Specimens were cured in air at ambient temperature, water at 25, 40 and 60 °C, sealed with plastic sheeting for 28 days. The results show that absorption and volume of permeable pore space (voids) of blended cement mortars at 28 day under all curing methods tend to increase with increasing silica fume replacement. The compressive strength of blended cement with fly ash and bottom ash was lower than that of Portland cement control at all curing condition while blended cement with silica fume shows higher compressive strength. In addition, the compressive strength of specimens cured with water increased with increasing curing temperature. The drying shrinkage of all blended cement mortar cured in air was lower than that of Portland cement control while the drying shrinkage of blended cement mortar containing silica fume, cured with plastic sealed and water at 25 °C was higher than Portland cement control due to pore refinement and high autogenous shrinkage. However, the drying shrinkage of blended cement mortar containing SF cured with water at 60 °C was lower than that of Portland cement control due to lower autogenous shrinkage and the reduced microporosity of C–S–H.     

Reuse of spent catalyst as fine aggregate in cement mortar

This study examined the feasibility of reusing spent zeolite catalyst, after fluidized catalytic cracking, as a substitute for fine aggregate (sand) in cement mortars. The tested result shows that spent catalyst can replace up to 10% of fine aggregate without decreasing the mortar strength. In fact, the substituted mortars show higher compressive strength than the unsubstituted samples. The flowability of the fresh mortars decreases with increasing substitution level and the mortars incorporated with spent catalyst show less bleeding. In the hardened state, the water absorption of the resulting mortar increases with longer curing age, higher substitution level and smaller water-to-cement (W/C) ratio. Toxicity characteristic leaching procedure (TCLP) analysis confirms that the spent catalyst meets the standard, and thus should be classified as general non-hazardous industrial waste.     

Influence of fired clay brick waste additions on the durability of mortars

The use of metakaolin is known to help improve properties of Portland cement-based mortars. The presumed similarities between the characteristics of metakaolin and those of a powdered (<45 μm) fired clay brick clean waste (CBW) led to the investigation of the effect on the durability of mortars of partial replacement (10, 25 and 40 wt.%) of Portland cement by CBW. Properties such as 28 and 90 days-compressive strength, water absorption, apparent porosity, absorption by capillarity, chloride retention, carbonation depth and sulphate resistance were evaluated. The CBW-containing cured mortars showed improved strength and density, as the result of combined physical and pozzolanic pore filling effect of added CBW. However, CBW-free mortar exhibited larger spreading and, being more porous, higher sulphate resistance and ability to absorb chlorides. Optimum performance was found for the 40 wt.% CBW mortar whose compressive strength can be up to 130% higher than that of the CBW-free mortar.     

Effect of nano clay particles on mechanical, thermal and physical behaviours of waste-glass cement mortars

Worldwide, around 2.6 billion tons of cement is produced annually. This huge size of production consumes large amounts of energy and is one of the largest contributors to carbon dioxide (CO₂) release. Accordingly, there is a pressing demand to minimise the quantity of cement used in the concrete industry. The main challenge to this is to get durable concrete with less cement and within reasonable cost. The economic, environmental and engineering benefits of reusing ground waste-glass powder (WGP) as a partial cement replacement has been established, but low glass reactivity and the possible alkali-silica reaction (ASR) are a drawback. Recent advances in nano-technology have revealed that nano-sized particles such as nano clay (NC) have a high surface area to volume ratio that provides the potential for tremendous chemical reactivity, accelerating pozzolanic activity and hindering ASR. This paper presents a laboratory study of the properties of NC/WGP cement composites. The microstructure, ASR, fracture energy, compressive and flexural properties of cement mortars containing WGP as a cement replacement with and without NC are investigated and compared with plain matrix. In addition, the hydration of cement compounds was followed by differential thermal analysis (DTA), thermogravimetric analysis (TGA), and also X-ray diffraction (XRD). The results showed that incorporation of glass powder has a positive effect on the mechanical properties of cement mortars after 28 days of hydration. Also, the results revealed that the mechanical properties of the cement mortars with a hybrid combination of glass powder and NC were all higher than those of plain mortar and with glass powder after 28 days of hydration. In addition, the DTA/TGA results and XRD analysis showed a reduction in the calcium hydroxide (CH) content in mortars with glass powder and with a hybrid combination of glass powder and NC, which confirms the improvements of mechanical properties and occurrence of pozzolanic reaction after 28 days of hydration.     

Rheological and hydration characterization of calcium sulfoaluminate cement pastes

Calcium sulfoaluminate (CSA) cements are currently receiving a lot of attention because their manufacture produces less CO₂ than ordinary Portland cement (OPC). However, it is essential to understand all parameters which may affect the hydration processes. This work deals with the study of the effect of several parameters, such as superplasticizer (SP), gypsum contents (10, 20 and 30 wt.%) and w/c ratio (0.4 and 0.5), on the properties of CSA pastes during early hydration. This characterization has been performed through rheological studies, Rietveld quantitative phase analysis of measured X-ray diffraction patterns, thermal analysis and mercury porosimetry for pastes, and by compressive strength measurements for mortars. The effect of the used SP on the rheological properties has been established. Its addition makes little difference to the amount of ettringite formed but strongly decreases the large pore fraction in the pastes. Furthermore, the SP role on compressive strength is variable, as it increases the values for mortars containing 30 wt.% gypsum but decreases the strengths for mortars containing 10 wt.% gypsum.     

Mussel Inspired Modification of Rubber Crumbs for Improved Interfacial Adhesion in Rubber Cement Mortar

Crumb rubbers exhibit extensive potential applications as infrastructure materials due to the low elastic modulus. Nevertheless, the poor interfacial adhesion between rubber crumb and cement matrix limits the scale applications of crumb rubbers in cement-based composites. In this study, mussel-inspired modification of crumb rubbers is investigated. The hydrophilicity of rubber surface has apparently improved after polydopamine (PDA) modification. Effects of the surface modifications of rubbers on the compressive strength, fluidity, and tribology behaviors of rubberized mortars have been systematically characterized. The superiority of PDA modification for crumb rubbers has been demonstrated by comparing those with the other polyphenol modifications and the routine oxidation modification. The compressive strength of the PDA modified rubber cement mortar increases by 37% comparing with that of the ordinary rubber cement mortar. The mechanical and low-temperature tribology behaviors of PDA-rubberized mortars indicate a promising way to improve the service performance of the rubberized mortars and concretes.

     

Properties of binary and ternary reactive MgO mortar blends subjected to CO2 curing

Research and development of low CO₂ binders for building material applications is warranted in efforts to reduce the negative environmental impacts associated with the cement and concrete industry. The purpose of this study is to investigate the effect of carbonation curing on the mineralogy, morphology, microstructure and evolution of compressive strength of mortars comprised of general use (GU) cement, ground granulated blast furnace slag (GGBFS), and reactive MgO used as cement replacement. This study investigates binary (GU–MgO) and ternary (GU–GGBFS–MgO) blends exposed to atmosphere curing (0.0038%CO₂) and carbonation curing (99.9%CO₂). Carbonation-cured mortars exhibited greater compressive strengths than atmosphere mortars at all ages (7 d, 28 d, and 56 d). Increasing percentages of reactive MgO decreased the compressive strength markedly less for carbonation-cured mortars than atmosphere-cured mortars particularly due to magnesium calcite formations. Magnesium calcite influenced the morphology of carbonates and promoted the carbonate agglomeration resulting in a dense and interconnected microstructure.     

A study on the effect of nano silica on compressive strength of high volume fly ash mortars and concretes

This paper presents the effect of nano silica (NS) on the compressive strength of mortars and concretes containing different high volume fly ash (HVFA) contents ranging from 40% to 70% (by weight) as partial replacement of cement. The compressive strength of mortars is measured at 7 and 28 days and that for concretes is measured at 3, 7, 28, 56 and 90 days. The effects of NS in microstructure development and pozzolanic reaction of pastes containing above HVFA contents are also studied through backscattered electron (BSE) image and X-ray diffraction (XRD) analysis. Results show that among different NS contents ranging from 1% to 6%, cement mortar containing 2% NS exhibited highest 7 and 28 days compressive strength. This NS content (2%) is then added to the HVFA mortars and concretes and the results show that the addition of 2% NS improved the early age (7 days) compressive strength of mortars containing 40% and 50% fly ash by 5% and 7%, respectively. However, this improvement is not observed at high fly ash contents beyond 50%. On the other hand, all HVFA mortars exhibited improvement in 28 days compressive strength due to addition of 2% NS and the most significant improvement is noticed in mortars containing more than 50% fly ash. In HVFA concretes, the improvement of early age (3 days) compressive strength is also noticed due to addition of 2% NS. The BSE and XRD analysis results also support the above findings.     

Sulfate resistance and carbonation of plain and blended cements

Results of an experimental investigation on the sulfate resistance and carbonation of plain and blended cement mortars are reported in this paper. In the sulfate resistance test all the specimens were immersed in a 5% Na₂SO₄ solution for 24 months. Two different types of lignite fly ashes and two natural pozzolans were used for the production of 13 blended cements. An ordinary portland cement and a commercially available blended cement were also used for reference. The effect of mineral admixtures on the carbonation depth of mortars was also investigated. Results show that the addition of pozzolanic admixtures in most cases had a positive effect on the sulfate resistance. The carbonation depth in all blended mortars was greater than that in portland cement mortar. However the rate of carbonation of blended mortars was reduced as hydration progressed.     

A study on the effects of high temperature on mechanical properties of fiber reinforced cementitious composites

The flexural strength and ductility properties of cementitious composites (mortar) under high temperature may be significantly improved by incorporating different types of fibers. In this study, four different types of fibers are added to cement mortars with the aim to investigate their mechanical contributions to mortars under high temperature, comparatively. Polypropylene (PP), carbon (CF), glass (GF) and polyvinyl alcohol (PVA) fibers are chosen for research. These fibers are added into mortars in five different ratios (0.0%, 0.5%, 1.0%, 1.50% and 2.0%) by volume. The mortars are subjected to the following temperatures: 21 °C (normal conditions), 100 °C (oven dry), 450 °C and 650 °C. The mechanical properties investigated are flexural strength, deflection and compressive strength of the cement mortars. In addition, thin sections of mortars are investigated to obtain changes in mortar because of high temperature. It is concluded that all fiber types contribute to the flexural strengths of mortars under high temperature. However, this contribution decreases with an increase in temperature. The samples with PVA show the best flexural performance (75–150%) under high temperature. CF which does not melt under high temperature also gives high flexural strength (11–85%). The compressive strengths of the mortars reduce under high temperature or with fiber addition. The highest increase in flexural strength and the lowest decrease in compressive strength is at 0.5–1.5% for CF if all temperature conditions are taken into consideration. The optimum fiber addition ratios of the samples containing PP and GF are 0.5% by volume. And for PVA, it is between 0.5% and 1.5% by volume.     

Pore size distribution and compressive strength of waste clay brick mortar

This paper reports the results of an investigation of the pore size distribution of mortar that contains varying amounts of ground brick from different European brick types. Clay brick deriving from four European countries was ground to roughly cement fineness and used to partially replace cement in quantities of 0%, 10%, 20% and 30% in standard mortars. The pore volume, pore size distribution, threshold radius and strength of these mortars were tested for curing periods of up to one year. The presence of ground brick (GB) alters significantly the compressive strength of mortar and this is attributed to both the dilution effect and production of additional C–S–H gel from reaction of GB with CH. The additional C–S–H gel refines the pore size distribution of the mortar and this is reflected in compressive strength values obtained for these mixes. A critical relationship between threshold radius and compressive strength is also observed.     

磁场诱导定向碳纤维增强水泥砂浆的力学性能

首次利用磁场诱导定向技术,制备了具有明显择优取向的碳纤维增强水泥砂浆,表征与测试了不同水灰比、龄期和纤维掺量的水泥砂浆的碳纤维取向、抗压和劈裂抗拉强度,研究了碳纤维的取向性对力学性能提升效果的影响。结果表明:水灰比、纤维掺量对碳纤维的取向性有显著影响;相较于无择优取向的普通碳纤维增强水泥砂浆,经磁场诱导定向的碳纤维增强水泥砂浆的劈裂抗拉强度有显著增加,而抗压强度无明显变化;相同水灰比下,纤维取向和纤维掺量是影响定向碳纤维增强水泥砂浆劈裂抗拉强度的主要因素。其中,定向碳纤维增强水泥砂浆劈裂抗拉强度增强效率的最佳碳纤维掺量为水泥的0.50%。      

The use of oil shale ash in Portland cement concrete

An experimental investigation was undertaken to study the potential use of Jordanian oil shale ash (OSA) as a raw material or an additive to Portland cement mortar and concrete. Different series of mortar and concrete mixtures were prepared at different water to binder ratios, and different OSA replacements of cement and/or sand. The compressive strength of mortar and concrete specimens, cured in water at 23 °C, was determined over different curing periods which ranged from 3 to 90 days. The results of these tests were subjected to a statistical analysis. Equations were developed by regression analysis techniques to relate the effect of batch constituents on the strength developments of OSA mortars and concretes. The models were checked for accuracy by comparing their predictions with actual test results.The obtained results indicated that OSA replacement of cement, sand or both by about 10% (by wt) would yield the optimum compressive strength, and that its replacement of cement by up to 30% would not reduce its compressive strength, significantly. It was found that OSA on its own possesses a limited cementitious value and that its contribution to mortar or concrete comes through its involvement in the pozzolanic reactions. The statistical model developed showed an excellent predictability of the compressive strength for mortar and concrete mixes.     

Function of styrene-acrylic ester copolymer latex in cement mortar

This paper focuses on the effect of the styrene-acrylic ester copolymer (SAE) latex on the performance of cement mortar, through studying on the water-reduction and water-retention effects of the SAE latex in the mortar, and the influence of the SAE latex on the air-content and the bulk density of the fresh mortar and the bulk density, compressive and flexural strengths, shrinkage rate, water capillary adsorption and anti-penetration capacity of the hardened mortar. The experimental results show that the SAE latex has good water-reduction and water-retention effects in mortar. The SAE latex has also air entrainment effect, increasing the air content and reducing the bulk density of the fresh mortar. The apparent bulk density and dry bulk density of the hardened mortars decrease with the increase of the SAE latex/cement-ratio (m_p/m_c) and the change is in accordance with that for the bulk density of the fresh mortar. The SAE latex influences the development of the compressive strength but slightly on the flexural strength, and improves the toughness, shrinkage property, waterproofing quality and anti-penetration capacity of the mortar significantly.     

Electrostatic self-assembled carbon nanotube/nano carbon black composite fillers reinforced cement-based materials with multifunctionality

Electrostatic self-assembled carbon nanotube (CNT)/nano carbon black (NCB) composite fillers are added into cement mortar to fabricate smart cement-based materials. The grape bunch structure of CNT/NCB composite fillers is beneficial for dispersing CNT/NCB in cement mortar matrix and achieving cooperative improvement effect. The mechanical, electrically conductive, and piezoresistive behaviors of the cement mortar are investigated. The CNT/NCB composite fillers can effectively enhance the flexural strength and electrical conductivity of cement mortars, and endow stable and sensitive piezoresistivity to cement mortar at a low filler content. However, they weaken the compressive strength of cement mortar to some extent. The percolation threshold zone of cement mortar with CNT/NCB composite fillers ranges in the amount of 0.39–1.52 vol.%. The optimal content of CNT/NCB composite fillers is 2.40 vol.% for piezoresistivity and the stress and strain sensitivities can reach 2.69% MPa⁻¹ and 704, respectively.     

Characteristics of cement-soil mortars

Cement-soil mortars are commonly used for the construction of soil-cement block masonry. The paper focuses on an experimental study in understanding the various characteristics of cement soil mortars in fresh and hardened state. Workability, strength, water retentivity, shrinkage and stress-strain characteristics of cement soil mortars and bond strength of soil-cement block couplets using such mortars are examined. Characteristics of 1:6 cement mortar and 1:1:6 cement lime mortar are also examined for the purposes of comparison. Workability of mortars has been quantified by conducting flow table tests. Results of flow values obtained for mortars from various construction sites are reported. There is a linear relationship between flow and water cement ratio of the mortars. Flow increases with increase in water-cement ratio. Very high flow value of 130% can be achieved for cement soil mortars and cement lime mortars. Reduction in flow value from 100% to 80% leads to increase in strength and modulus of mortars. Clay fraction of the mortar mix controls the flow, strength, density, shrinkage value and modulus of cement soil mortars. Cement-soil mortars lead to better tensile bond strength for soilcement block couplets when compared to the cement mortar and cement lime mortar.     

Compressive strength development of binary and ternary lime–pozzolan mortars

This study considers the compressive strength development of broad range of hydraulic lime mortars prepared with a range of commercially available alumino-silicate by-products and modern pozzolanic additions. Specifically this paper considers the effect of mineral addition selection, binary and ternary combinations, pozzolan content and the effect of curing conditions on the compressive strength development of hydraulic lime based mortars. The study was undertaken as the initial phase of a broader investigation considering the feasibility of producing modern, sustainable hydraulic lime–pozzolan concretes with comparable strengths to Portland cement based concretes. The aim of the initial phase was to identify a small number of additions, and combinations thereof, which would result in a structural strength lime–concrete when scaled up from mortars to concretes.In the absence of a definitive source of information on the mechanical properties of hydraulic-lime mortars prepared with binary and ternary combinations of alumino-silicate by-products, 22 combinations consisting of Natural Hydraulic Lime (NHL5) and a range of possible additions, identified from historical and current practice, were prepared. The results have shown that combining an eminently-hydraulic NHL5 with silica fume and ground granulated blastfurnace slag can produce mortars with a 28-day compressive cube strength of around 28 N/mm², at a water-to-binder (w/b) ratio of 0.5. This is eight times the strength of an equivalent mortar prepared with NHL5 alone and broadly speaking comparable with that of low-heat cementitious mortars. The contribution of the pozzolanic reaction to the strength of hydraulic lime mortars is discussed for a range of alumina-silicious materials and combinations thereof.     

Feasible use of large volumes of GGBS in 100% recycled glass architectural mortar

The use of 100% recycled glass as aggregates in architectural mortar is regarded as an environmentally friendly, cost-effective and attractive feature for construction applications due to the natural characteristics of glass (e.g. aesthetic pleasing, impermeability, chemical resistance properties). However, the need to use large quantities of white cement for architectural products may increase the overall cost of production. Therefore, the possibility of using a near-white coloured ground granulated blast furnace slag (GGBS) to replace white cement for architectural mortar production is an attractive option. This paper reports a study which is an extension of our previous work aiming to investigate the feasibility of using large volumes of GGBS (ranging from 15% to 75% white cement replacements) to produce self-compacting-based architectural mortars. To improve the appearance (whiteness) of the mortar, a small quantity of titanium dioxide (TiO₂) was added to the selected mixes for comparison purposes. Fresh and hardened properties of the mortar including mini-slump flow, density, water absorption, flexural strength, equivalent compressive strength, drying shrinkage, alkali silica reaction (ASR) and acid attack resistance were investigated. The overall performance showed that it is feasible to use GGBS for the production of architectural mortar and 60% replacement of white cement by GGBS was determined to be optimal. The replacement significantly increased the flexural strength, and reduced the drying shrinkage and risk of ASR expansion, as well as improved the ability to resist acid attack of the mortar produced.