Surface Stickiness of Drops of Carbohydrate and Organic Acid Solutions During Convective Drying: Experiments and Modeling

Abstract

Drying kinetics of low molecular weight sugars such as fructose, glucose, sucrose and organic acid such as citric acid and high molecular weight carbohydrate such as maltodextrin (DE 6) were determined experimentally using single drop drying experiments as well as predicted numerically by solving the mass and heat transfer equations. The predicted moisture and temperature histories agreed with the experimental ones within 6% average relative (absolute) error and average difference of ± 1°C, respectively. The stickiness histories of these drops were determined experimentally and predicted numerically based on the glass transition temperature (T _g ) of surface layer. The model predicted the experimental observations with good accuracy. A nonsticky regime for these materials during spray drying is proposed by simulating a drop, initially 120 µm in diameter, in a spray drying environment.     

Thin Layer Drying Models for Osmotically Pre-dried Young Coconut

Thin layer convection drying was performed on osmotically pre-dried young coconut, strips, both thin and thick. A drying air temperature range of 50-70°C and an airflow of 0.25 m s^-1 was used to dry samples soaked in three sugar solution concentrations (40, 50, and 60°B) during the osmotic drying phase, with the convection drying alone serving as control. An analysis of variance (ANOVA) revealed that sugar concentration and thickness significantly affected osmotic drying rates as shown by their final moisture contents. While the drying air temperature and slab thickness significantly affected the average drying rate and the sugar concentration was an insignificant factor during convective drying phase. Effective diffusivity of water during hot air drying varied from 1.71 to 5.51 × 10^-10 m²s^-1 over the temperature range investigated, with energy of activation equal to 1173.0 kJ/kg. Three mathematical models available in the literature were fitted to the experimental data, with the Page model giving better predictions than the single or double term exponential model. The temperature dependence of the diffusivity coefficients was satisfactorily described by a simple Arrhenius type relationship.     

Supercritical CO2 Spray Drying of Ethyl Cellulose (EC) for Preparing Microparticles

Even though common spray drying has been widely used for drying food and related products, the effect of drying conditions of supercritical CO₂ spray drying on the particle sizes of dried products has not been well studied. The objective of this study was to study the effect of drying conditions and design parameters on the particle sizes of biomaterials dried with supercritical CO₂ spray drying. The ethyl cellulose (EC) microparticles were prepared with supercritical CO₂ as the dry medium using an experimental spray-drying apparatus. This research studied the influences of spray nozzle diameter, mass ratio of gas to liquid, solution concentration, temperature, and pressure on the physical characteristics of ethyl cellulose microparticles. The results indicated that the average size of the dried particles ranged from 1.07 to 9.84 µm. The spray nozzle with 8-mm diameter produced smaller microparticles with narrower distribution than the 4-mm spray nozzle. The average particle size increased with the increase of the ratio of gas to liquid. Also, the average size and distribution of the microparticles increased with the rise of temperature and solution concentration but decreased with the increase of pressure.     

Pneumatic Drying of Iron Ore Particles in a Vertical Tube

The drying and hydrodynamic characteristics of iron ore particles in a vertical pneumatic conveying dryer (0.078 m ID × 6.0 m high) have been determined. The pressure drop decreases along the height at the acceleration region, while it remains constant irrespective of the height in the fully developed region. The degree of particle drying in the dilute pneumatic region increases with increasing superficial inlet gas velocity at constant inlet gas temperature and solid injection rate. However, it decreases with increasing solid injection rates at identical superficial inlet gas velocity and inlet gas temperature. The degree of particle drying increases from 48.6 to 82.5% as the inlet gas temperature increases from 100 to 400 °C.     

From Laboratory Experiments to Design of a Conveyor-Belt Dryer via Mathematical Modeling

A conveyor-belt dryer for picrite has been modeled mathematically in this work. The necessary parameters for the system of equations were obtained from regression analysis of thin-layer drying data. The convective drying experiments were carried out at temperatures of 40, 60, 80, and 100°C and air velocities of 0.5 and 1.5 m/sec. To analyze the drying behavior, the drying curves were fitted to different semi-theoretical drying kinetics models such as those of Lewis, Page, Henderson and Pabis, Wang and Singh, and the decay models. The decay function (for second order reactions) gives better results and describes the thin layer drying curves quite well. The effective diffusivity was also determined from the integrated Fick's second law equation and correlated with temperature using an Arrhenius-type model. External heat and mass transfer coefficients were refitted to the empirical correlation using dimensionless numbers (J_h, J_D = m · Reⁿ) and their new coefficients were optimized as a function of temperature. The internal mass transfer coefficient was also correlated as a function of moisture content, air temperature, and velocity.     

Effect of Pulsed Electric Field and Osmotic Dehydration Pretreatment on the Convective Drying of Carrot Tissue

The influence of pulsed electric field (PEF) and subsequent centrifugal osmotic dehydration (OD) on the convective drying behavior of carrot is investigated. The PEF was carried out at an intensity of E = 0.60 kV/cm and a treatment duration of t_PEF = 50 ms. The following centrifugal OD was performed in a sucrose solution of 65% (w/w) at 40°C for 0, 1, 2, or 4 h under 2400 × g. The drying was performed after the centrifugal OD for temperatures 40-60°C and at constant air rate (6 m³/h).

With the increase of OD duration the air drying time is reduced spectacularly. The dimensionless moisture ratio Xr = 0.1 is reached for PEF-untreated carrots after 370 min of air drying at 60°C in absence of centrifugal OD against 90 min of air drying after the 240 min of centrifugal OD. The PEF treatment reduces additionally the air drying time. The total time of dehydration operations can be shortened when OD time is optimized. For instance, the minimal time required to dehydrate untreated carrots until Xr = 0.1 is 260 min (120 min of OD at 40°C and 140 min of drying at 60°C). It is reduced to 230 min with PEF-treated carrots.

The moisture effective diffusivity D_eff is calculated for the convective air drying based on Fick's law. The centrifugal OD pretreatment increases drastically the value of D_eff. For instance, 4 h of centrifugal OD permitted increasing the value of D_eff from 0.93 · 10^-9 to 3.85 · 10^-9 m²/s for untreated carrots and from 1.17 · 10^-9 to 5.10 · 10^-9 m²/s for PEF-treated carrots.     

Drying Characteristics of Purslane (Portulaca oleraceae L.)

Thin layer drying rates of purslane were determined experimentally as a function of temperature with air velocity kept constant at 1.1 m/s and relative humidity below 5%. Thin layer drying data were obtained for purslane at four drying air temperatures (35, 70, 95, and 120°C). Five thin layer-drying models (Henderson and Pabis, exponential, Page, two-term exponential, and Thompson models) were fitted to the drying data. The color of purslane was determined after drying using a spectro-colorimeter (Hunter Lab) in terms of Hunter L, a, and b values. The Page model was found to be most suitable in describing the drying characteristics of purslane. New parameters developed for the model resulted in a good fit at different temperatures. Color measurement indicated that greenness decreased with an increase in drying air temperature. Typical drying times were 88.41, 138.53, 416.38, and 1371.85 min at 120, 95, 70, and 35°C, respectively.     

Accurate Determination of Moisture Content of Organic Soils Using the Oven Drying Method

The accuracy of moisture content values determined for organic soil using the oven drying method is dependent on the oven drying temperature. Some charring of the organic fraction occurs at the standard oven drying temperature of 110 ± 5°C; pore water remains in the soil when temperatures below 100°C are used. A new technique to determine the specific oven drying temperature that yields the correct value of the moisture content for organic soils is presented. Routine moisture content tests should be conducted at the standard oven drying temperature; moisture content values determined on the basis of the recommended oven drying temperature of 60°C include a larger error. A moisture content parameter is introduced to facilitate direct comparison of moisture content values calculated on the basis of different oven drying temperatures.     

Constant and Intermittent Drying Characteristics of Olive Cake

The drying kinetics of olive cake, the solid by-product of the olive oil extraction process, has been experimentally investigated in a small-scale tray dryer using both constant and intermittent (on/off) heating schemes. The parameters investigated include inlet air temperature and intermittency of heat input. The drying kinetics was interpreted through two mathematical models, the Page equation and the Lewis equation. The Page equation was most appropriate in describing the drying behavior of olive cake. A diffusion model was used to describe the moisture transfer and the effective diffusion coefficient at each temperature was determined. The dependence of the effective diffusion coefficient on drying temperature can be adequately explained based on an Arrhenius-type relation. The effective diffusion coefficient varied between 7.6 × 10^-8 and 2.5 × 10^-7 m²/min with an activation energy of 38.55 kJ/mol. Comparison of time evolution of material moisture content due to intermittent and constant drying is also made.     

PERFORMANCE STUDY OF A RE-CIRCULATING CABINET DRYER USING A HOUSEHOLD DEHUMIDIFIER

The performance and operating characteristics of a low temperature re-circulating cabinet dryer using a dehumidifier loop were studied using alfalfa. Chopped alfalfa, initially at 70% moisture content, was dried to 10% moisture content in the dryer. Two dryer setups were used. The dryers in each case had a partitioned cabinet with trays of material on one side and a stack of one or two small household dehumidifiers on the other side. Air was re-circulated through the material from bottom to the top and back through the dehumidifiers. Two drying configurations were tested. In one, the material was left on the trays until drying was complete (batch or fixed tray drying). In the other configuration, the trays were moved from top to bottom, introducing a new tray at the top while removing an old tray from bottom. Drying air temperature ranged from 25 to 45°C. The average air velocity through the material was 0.38 m/s. Alfalfa chops dried in 5 h in the fixed tray drying and in 4 h in the moving tray drying. The specific moisture extraction rate ranged from 0.35 to 1.02 kg/kWh for batch drying and stayed at an average value of 0.50 kg/kWh for continuous/moving tray drying.     

Application of Bi-S Drying Correlation to Microwave Drying Data of Pharmaceutical Powders

The moisture diffusivities and moisture transfer coefficients characterising the drying of pharmaceutical powders were determined using a correlation proposed by Dincer et al. (2002, Development of a new drying correlation for practical applications. International Journal of Energy Research 26, 245-251). Experimental moisture content data for lactose, Aspirin and Paracetamol samples dried under convective, microwave, combined convective-microwave and combined vacuum-microwave conditions were obtained. The drying coefficients and lag factors were determined from the experimental measurements and incorporated into the model. The mass transfer Bi numbers were found to be in the range 0.058 to 0.194, indicating the presence of finite internal and external resistances. Moisture diffusivity and diffusion coefficient values in the range 0.135 × 10^-9 to 102 × 10^-9 m² s^-1 and 0.067 × 10^-7 to 8.21 × 10^-7 ms^-1 respectively, were calculated. The predicted moisture profiles showed adequate agreement with the experimental observations, with the average error between experimental and predicted results being ± 15.9%.     

Drying Kinetics and Sorption Isotherms of the Nejayote

The nixtamalization is an alkaline cooking process in corn tortillas industry that uses large quantities of water (5:1 corn weight) and producing a byproduct called nejayote. In this work, drying kinetic of insoluble fraction from nejayote was obtained using a hot air cabinet dryer at 60, 75, and 90°C. The air rate and water content were 1.5 m/s and 0.028 kg of water/kg of dry air, respectively. Sorption isotherms were measured by the COST method with sulfuric acid solutions at 30, 45 and 60°C. Results showed a difference in drying kinetics/drying time between drying temperatures of 60 and 75°C, and practically no difference between 75 and 90°C. This was probably due to the development of a superficial crust on the product. The shape of sorption curves was as expected; no temperature effect was identified but it is a common behavior for products with high sugar content. Finally the sorption isotherm was predicted based on primary chemical compounds (carbohydrates, proteins, crude fiber, and calcium hydroxide).     

Drying Kinetics and Color Retention of Dehydrated Rosehips

Freshly harvested rosehips (Rosa canina L.) were dehydrated in a parallel flow type air dryer at six air temperatures (30, 40, 50, 60, and 70°C) at air velocities of 0.5, 1.0, and 1.5 m/s. Drying air temperature and velocity significantly influenced drying time and energy requirement. Minimum and maximum energy requirement for drying of rosehips were determined as 6.69 kWh/kg for 70°C at 0.5 m/s, and 42.46 kWh/kg for 50°C, 1.5 m/s. In order to reduce drying energy consumption, it is recommended that the drying air velocity must not be more than 0.5 m/s and drying air temperature should be 70°C. In addition, the influence of drying air temperature and air velocity on the color of dried rosehip has been studied. Hunter L, a, b values were used to evaluate changes in the total color difference (ΔE) on dried rosehips. 70°C drying air temperature and 1 m/s air velocity were found to yield better quality product.     

COMPARISON OF GLASS TRANSITION TEMPERATURE AND STICKY POINT TEMPERATURE FOR SKIM MILK POWDER

Wall deposition of particles in spray dryers is a key processing problem, and information about the glass transition temperature of the amorphous material that arises from spray drying can be used to guide the selection of operating conditions that may minimise wall deposition. The glass transition temperatures for skim milk powder with various moisture contents were determined using Differential Scanning Calorimetry (DSC), and a repeatable glass transition temperature diagram was established from these results. The glass transition temperature decreased as the moisture content increased, as expected (low moisture content 1.65 g/100 g of dry powder, glass transition temperature 87.7°C; high moisture content 4.52 g/100 g of dry powder, glass transition temperature 46.7°C). The glass transition temperature was found to be virtually the same as the sticky-point temperature measured using a thermo-mechanical test. The difference is essentially due to the difference between doing a mechanical test for viscosity (sticky-point) and a phase transition measurement (DSC).     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

Partial Crystallization Behavior during Spray Drying: Simulations and Experiments

Simulations of crystallization behavior in a spray dryer have been performed using modifications to a model developed by previous workers and applied to a Buchi-290 laboratory-scale dryer. The potential crystallization behavior has been modeled using Williams-Landel-Ferry kinetics. Explorations using the model have suggested that the air inlet temperature is an important variable affecting crystallization in the dryer. The explorations suggested drying conditions that permitted reasonable drying while controlling the degree of crystallization. These conditions were examined and tested experimentally, also showing that the apparent degree of crystallinity was affected by the inlet air temperature over the range of inlet temperatures from 134°C (∼55% crystalline) to 210°C (∼76% crystalline). The simulation also predicted the trends in the experimental results from previous workers where their experimental results are considered in terms of the measurement techniques used in each case, suggesting that the simulation is a reasonable tool for developing operating conditions for drying equipment to give low or high degrees of crystallinity in the products.     

EVALUATION AND MODELING OF TWO-STAGE OSMO-CONVECTIVE DRYING OF APPLE SLICES

Two-stage drying kinetics of cylindrical pieces of apples were evaluated by subjecting test samples first to various osmotic treatments and then to convective air drying to complete the drying process. Osmotic drying was carried out with cut apple cylinders of three different sizes (12, 17 and 20 mm diameter), all with a length to diameter ratio of 1 : 1, in a well agitated large tank containing the osmotic solution at the desired temperature. Solution to fruit volume ratio was kept greater than 60. After the osmotic treatment, apple slices were further dried in a cabinet drier at an average temperature 58°C. A central composite rotatable design (CCRD) with five levels of sucrose concentrations (34-63°Brix) and five temperatures (34-66°C) was used for osmotic treatment. Half-drying time and solids gain time were used as measures of rate of drying and associated diffusion coefficients for moisture loss and solids gain were evaluated. Half-drying time decreased with an increase in temperature or concentration, or a decrease in sample size. Diffusion coefficients were lower for smaller samples, and were higher for migration of moisture as compared to solids. For a given level of moisture removal, air drying times were shorter than osmotic drying times. Composite models were developed to describe the effect of process variables and particle size on the drying behavior of apple slices.     

Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and without a Cyclone

The objective of the present work is to find the possibility of reducing the high initial moisture content of wet paddy using a small-scale, low-cost pneumatic conveying dryer that can be provided for each farming household. The dryer without a cyclone equipped at the exit of the dryer is studied and the data obtained from this system is compared with those obtained previously from the dryer with a cyclone. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, and drying air temperature from 35 to 70°C. From the experimental results it is found that the drying process with and without a cyclone are able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. For the same experimental conditions, the cyclone-equipped dryer gives around 1% higher decrease of moisture content, 2°C higher average surface temperature of paddy, 3-4% higher average percentage of head rice yield, and 2 kg/h higher average evaporation rate. However, the energy consumption per evaporated mass of water is 20-30% lower than the non-cyclone-equipped dryer.     

Influence of Temperature and Air Velocity on Drying Time and Quality Parameters of Pistachio (Pistacia vera L.)

Drying is one of the important steps in pistachio processing. In this step kernel moisture content is decreased from 50 to less than 5% (d.b.) which will result in suitable condition for storage. Study of effective parameters in pistachio drying is important since these parameters influence drying time and kernel quality. In this research, a mono layer of pistachios was dried at three different temperatures (60, 75, and 90°C), and three levels of drying air velocity (1.5, 2, and 2.5 m/s). Changes of drying time, protein, fat and peroxide value were investigated for two common Iranian pistachio varieties Kalehghouchi and Fandoghi. Sensory tests were also used to check flavor of pistachios dried at the three temperature levels (60, 75, and 90°C). Statistical analysis of the data indicated that increasing the temperature to 90°C reduced drying time down by about 37% and caused a change in pistachio flavour. Taste tests indicated a consumer preference for pistachios dried at 75°C. If the air velocity is increased from 1.5 to 2.5 m/s, drying time reduces about 10 percent. Changes in temperature and air velocity have no significant effects on protein and fat content of pistachios, but if temperature reaches 90°C, peroxide value will increase to 0.55 meq/kg, which is still within the permissible limit for processed pistachios.     

Experiments on In-Store Paddy Drying Under Tropical Climate: Simulation and Product Quality

The main objective of this work is to study the rice whiteness and paddy qualities of rice in terms of hardness, stickiness, cohesiveness, and germination of rice. The prediction results of moisture content and whiteness are compared with the experimental results using a near-equilibrium drying model, which is modified by including whiteness kinetics of rice kernel. The long grain rice (Suphanburi 1 high amylose indica variety), which consists of 27% amylose was used for all experiments. The experiments were carried out at the average ambient temperature range of 28.6-30.8°C, average relative humidity of 65.2-80.6% with a fixed bed depth of 1.0 m. Specific air flow rates of 0.65 and 0.93 m³/min-m³ of paddy were forced continuously through the paddy bulk at initial moisture contents of 18.5% and 20.1% wet basis, respectively. The desired final moisture content of paddy is about 13.3 ± 0.6% wet basis. The results show that drying rate and the whiteness predictions are in good agreement with those from the experiments. The in-store drying using ambient air condition did not produce notable effect on the rice whiteness, head rice yield, and the percentage of paddy germination. However, the hardness, stickiness, and cohesiveness of rice were changed.