压电厚膜驱动的高刚度微变形镜的制备

研究制备了一种压电厚膜微变形镜,微变形镜的连续薄膜式单晶硅镜面由61单元压电厚膜致动器阵列驱动.以镜面冲程与工作频带宽为目标,对微变形镜的结构参数进行优化设计,根据优化参数采用硅微加工技术试制了61单元致动器的微变形镜.镜面、压电陶瓷与弹性支撑层厚度分别为100μm、60μm与60μm,单元间距为5mm,通光口径为40 mm.对制备的样品性能进行了测试,微变形镜在100 V电压驱动下变形量约为2.84μm,工作带宽大于10 kHz.测试结果还表明压电厚膜驱动的微变形镜拥有较高刚度,有利于提高镜面初始平面度.     

用于心磁传感器测试系统的三轴向亥姆赫兹线圈的设计与仿真

心磁检测对于心脏相关疾病的诊断具有独特优势，在用于测量心脏磁场的传感器(下称心磁传感器）的研制过程中，需要在模拟心磁的磁场环境下进行测试工作。基于此，设计了一个用于心磁传感器测试系统的亥姆赫兹线圈，它可以产生磁感应强度为pT级的动态磁场，模拟心磁环境，以满足心磁传感器测试的需求。根据亥姆赫兹线圈的磁场产生原理，使用磁屏蔽筒对环境磁场进行屏蔽，通过计算确定了线圈尺寸、线圈匝数、导线长度及导线横截面直径等参数。使用COMSOL Multiphysics仿真软件对亥姆赫兹线圈产生的静态磁场的分布均匀性以及通入线圈电流变化时磁场的动态特性进行仿真分析。仿真结果表明，所设计的亥姆赫兹线圈满足设计要求，能够产生磁场强度为100 pT左右、均匀度小于5%、波形实时性好的类心脏磁场波形，为心磁传感器的测试提供了良好的测试环境。所设计的亥姆赫兹线圈能够用于心磁传感器的测试工作，为心磁传感器的实际应用奠定了基础。     

超精密大行程麦克斯韦磁阻驱动器磁场建模与推力分析

为了克服大行程麦克斯韦磁阻驱动器在大气隙下漏磁大幅增加、气隙区磁场分布不均匀且非线性强烈等现象导致的磁场和推力解析模型精度较低等问题,利用考虑综合高斯函数的加权漏磁系数的磁路建模方法,改进了磁阻驱动器的三维漏磁分布计算方式,并得到了可准确描述其推力与输入电流函数关系的解析模型,从而为该类驱动器的设计及控制提供重要依据。首先,建立了大行程麦克斯韦磁阻驱动器考虑漏磁前后的工作磁路,分析了永磁偏置磁路的作用及使用永磁偏置结构后仍具有非线性的原因,并利用安培环路定律和磁路的欧姆定律以及磁场的可叠加性,建立了该磁阻驱动器的推力解析模型。然后,为了优化解析模型,提出了基于高斯曲线的加权漏磁系数计算方法,同时利用有限元仿真软件对大行程麦克斯韦磁阻驱动器的三维磁场分布及漏磁系数进行了分析计算,得到了考虑加权漏磁系数的推力解析模型。最后,搭建了大行程麦克斯韦磁阻驱动器推力测试系统,并通过对比优化前后解析模型计算推力与仿真推力和实测推力,验证了解析模型的准确性。结果表明,优化后解析模型的均方根误差仅为优化前的11.1%,其精度得到有效提升;同时,优化后解析模型计算推力与实测推力之间的均方根误差小于0.6 N,精度较高。研究结果对高端微纳制造装备与测量仪器中新型超精密驱动部件的设计有一定意义和参考价值。     

大行程变形镜有限元分析

针对自适应光学系统对变形镜行程的更高要求,本文对提高变形镜行程技术进行了分析,提出了一种解决变形镜大行程的方法:匹配、优化变形镜的结构参数;利用有限元软件分析了该结构的各参数对变形镜主要性能指标:最大变形量、交连值及最大应力等的影响.根据分析结果,利用有限元分析方法对一自适应光学望远镜所用变形镜的镜面、驱动器结构参数进...     

新型静电驱动双向平动MEMS变形镜(英文)

设计了一种新型静电驱动双向平动的MEMS变形镜,其结构包括3部分:中央下电极,4个静电驱动杠杆结构以及反射镜面(上电极).该变形镜有两种驱动模式:向下驱动模式和向上驱动模式.在向上驱动时,4个杠杆结构实现了位移的放大;向下驱动时,利用了非线性弹性系数法扩展了镜面的平动范围.采用表面硅工艺完成了变形镜的加工.通过白光干涉仪对变形镜的测试表明:在向上驱动模式下,变形镜在驱动电压为31 V时位移达到1.1μm;在向下驱动模式下,变形镜在6 V的驱动电压下位移达到1.1μm.变形镜的总行程为2.2μm,达到了同样工艺下传统变形镜的3倍左右.     

变形镜极间电压保护网络研究

对于连续镜面变形镜,相邻驱动器的相对位移过大会损坏变形镜。保护网络通过控制极间电压,保护变形镜。文章介绍了保护网络的方案,建立数学模型并进行了仿真验证,分析了保护网络对自适应光学系统稳定性的影响。最后应用有限元分析软件,讨论加入保护网络后,61单元变形镜拟合象差的能力变化。     

电磁热水器磁屏蔽有限元分析

为降低电磁热水器工作时产生的磁场干扰,需要进行磁屏蔽的设计。针对某电磁热水器,采用有限元软件仿真对高频和低频屏蔽方式的屏蔽效能及其对系统效率的影响展开研究。研究屏蔽壳厚度、两线圈距离及其电流相位差等因素对热水器产生的磁场强度的影响。结果表明:该电磁热水器更宜采用高频屏蔽方式,两线圈电流反相、缩小两线圈间距等措施可降低热水器周围磁场强度,更有利于磁屏蔽的设计。     

高速旋转平面反射镜镜面变形测量

本文将介绍高速旋转平面反射镜镜面变形测量。平面反射镜在高速旋转时由于镜体倾斜引起的惯性力矩会使镜体产生弯曲变形,影响成像质量。利用应变电测法,通过导电滑环把镜体旋转时镜面应变片电阻变化信号连接到应变仪。从变形与应变之间的关系,用仿真方法估计镜体等效厚度,数值积分重构镜体弯曲变形。并与有限元计算结果进行对比,验证测量的正确性。研究表明:该方法有效可行,为旋转镜面变形测量提供一种新的思路。     

经穴磁刺激线圈优化设计与仿真

经穴磁刺激与传统针灸、电刺激相比具有无创伤、无不适感、易重复和进行深部刺激等独特优点.磁刺激系统中载流线圈设计对磁场强度和磁场分布具有重要作用.在理论分析载流线圈磁场分布基础上,设计了不同8字形和碗状结构磁刺激线圈,并采用Ansys有限元分析软件对线圈沿径向和轴向产生的磁场分布进行仿真,研究8字形和碗状结构线圈的磁场聚焦性和刺激深度.结果表明,碗状线圈具有较好的磁场聚焦性且有一定的刺激深度,在皮层下1.5～2 cm左右仍有3～10 mT的磁场强度.同时获得了适合于经穴磁刺激系统的最佳线圈形状和参数,为穴位磁刺激技术应用于临床治疗奠定了良好基础.     

圆筒状超磁致伸缩致动器磁场研究与仿真

为设计圆筒状超磁致伸缩致动器(GMA),采用基于磁路的方法对圆筒状超磁致伸缩材料(GMM)内的磁场强度进行计算,基于Maxwell软件建立了圆筒状GMA的3D模型并对磁路结构中各部件尺寸及GMA筒内构件的磁导率对磁场的影响进行了仿真研究。结果表明:在闭合的磁路结构中,对于给定的线圈匝数和激励电流,GMM筒中磁场强度大小受GMM筒轴向长度影响较大且为负相关。磁场均匀性方面,影响较大的是穿过圆筒状GMA构件的磁导率和导磁环轴向长度,二者均与磁场不均匀度正相关。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from