Effects of Cooling Rate on Thermoelectric Properties of <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>(Se<Subscript>0.4</Subscript>Te<Subscript>0.6</Subscript>)<Subscript>3</Subscript> Compounds

A series of Bi₂(Se_0.4Te_0.6)₃ compounds were synthesized by a rapid route of melt spinning (MS) combined with a subsequent spark plasma sintering (SPS) process. Measurements of the Seebeck coefficient, electrical conductivity, and thermal conductivity were performed over the temperature range from 300 K to 520 K. The measurement results showed that the cooling rate of melt spinning had a significant impact on the transport properties of electrons and phonons, effectively enhancing the thermoelectric properties of the compounds. The maximum ZT value reached 0.93 at 460 K for the sample prepared with the highest cooling rate, and infrared spectrum measurement results showed that the compound with lower tellurium content, Bi₂(Se_0.4Te_0.6)₃, possesses a larger optical forbidden gap (E _g) compared with the traditional n-type zone-melted material with formula Bi₂(Se_0.07Te_0.93)₃. Our work provides a new approach to develop low-tellurium-bearing Bi₂Te₃-based compounds with good thermoelectric performance.     

Effect of Electric Current on the Performance of Bi<Subscript>1.2</Subscript>Sb<Subscript>4.8</Subscript>Te<Subscript>9</Subscript> Thermoelectric Material Prepared by a Field-Activated Pressure-Assisted Sintering Process

Field-activated pressure-assisted sintering (FAPAS) was applied to sinter Bi_1.2Sb_4.8Te₉ thermoelectric materials under different conditions, including no-current sintering (NCS), low-density current sintering (LCS), and high-density current sintering (HCS). The effect of the current density on the final thermoelectric performance of the products was investigated. Applying a higher-density electric current and shorter dwell time can improve the thermoelectric performance of the sample by increasing its electric conductivity and decreasing its thermal conductivity. The maximum figure of merit ZT values of the NCS, LCS, and HCS samples were 0.46, 0.48, and 0.57, respectively. Therefore, applying a high-density electric current in the sintering process may be an effective way to obtain Bi_1.2Sb_4.8Te₉ thermoelectric material with high ZT value.     

Effects of SiC Nanodispersion on the Thermoelectric Properties of <Emphasis Type="Italic">p</Emphasis>-Type and <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Alloys

Polycrystalline p-type Bi_0.5Sb_1.5Te₃ and n-type Bi₂Te_2.7Se_0.3 thermoelectric (TE) alloys containing a small amount (vol.% ≤5) of SiC nanoparticles were fabricated by mechanical alloying and spark plasma sintering. It was revealed that the effects of SiC addition on TE properties can be different between p-type and n-type Bi₂Te₃-based alloys. SiC addition slightly increased the power factor of the p-type materials by decreasing both the electrical resistivity (ρ) and Seebeck coefficient (α), but decreased the power factor of n-type materials by increasing both ρ and α. Regardless of the conductivity type, the thermal conductivity was reduced by dispersing SiC nanoparticles in the Bi₂Te₃-based alloy matrix. As a result, a small amount (0.1 vol.%) of SiC addition increased the maximum dimensionless figure of merit (ZT _max) of the p-type Bi_0.5Sb_1.5Te₃ alloys from 0.88 for the SiC-free sample to 0.97 at 323 K, though no improvement in TE performance was obtained in the case of n-type Bi₂Te_2.7Se_0.3 alloys. Importantly, the SiC-dispersed alloys showed better mechanical properties, which can improve material machinability and device reliability.     

Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> Superlattices Grown by Nanoalloying

In this work, Bi₂Te₃-Sb₂Te₃ superlattices were prepared by the nanoalloying approach. Very thin layers of Bi, Sb, and Te were deposited on cold substrates, rebuilding the crystal structure of V₂VI₃ compounds. Nanoalloyed super- lattices consisting of alternating Bi₂Te₃ and Sb₂Te₃ layers were grown with a thickness of 9 nm for the individual layers. The as-grown layers were annealed under different conditions to optimize the thermoelectric parameters. The obtained layers were investigated in their as-grown and annealed states using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive x-ray (EDX) spectroscopy, transmission electron microscopy (TEM), and electrical measurements. A lower limit of the elemental layer thickness was found to have c-orientation. Pure nanoalloyed Sb₂Te₃ layers were p-type as expected; however, it was impossible to synthesize p-type Bi₂Te₃ layers. Hence the Bi₂Te₃-Sb₂Te₃ superlattices consisting of alternating n- and p-type layers showed poor thermoelectric properties.     

Low-Temperature Thermoelectric Properties of Co<Subscript>0.9</Subscript>Fe<Subscript>0.1</Subscript>Sb<Subscript>3</Subscript>-Based Skutterudite Nanocomposites with FeSb<Subscript>2</Subscript> Nanoinclusions

Bulk thermoelectric nanocomposite materials have great potential to exhibit higher ZT due to effects arising from their nanostructure. Herein, we report low-temperature thermoelectric properties of Co_0.9Fe_0.1Sb₃-based skutterudite nanocomposites containing FeSb₂ nanoinclusions. These nanocomposites can be easily synthesized by melting and rapid water quenching. The nanoscale FeSb₂ precipitates are well dispersed in the skutterudite matrix and reduce the lattice thermal conductivity due to additional phonon scattering from nanoscopic interfaces. Moreover, the nanocomposite samples also exhibit enhanced Seebeck coefficients relative to regular iron-substituted skutterudite samples. As a result, our best nanocomposite sample boasts a ZT = 0.041 at 300 K, which is nearly three times as large as that for Co_0.9Fe_0.1Sb₃ previously reported.     

Features of the charge-transport mechanism in layered Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> single crystals doped with chlorine and terbium

The temperature dependences (T = 5−300 K) of the resistivity in the plane of layers and in the direction perpendicular to the layers, as well as the Hall effect and the magnetoresistance (H < 80 kOe, T = 0.5−4.2 K) in Bi₂Te₃ single crystals doped with chlorine and terbium, are investigated. It is shown that the doping of Bi₂Te₃ with terbium atoms results in p-type conductivity and in increasing hole concentration. The doping of Bi₂Te₃ with chlorine atoms modifies also the character of its conductivity instead of changing only the type from p to n. In the temperature dependence of the resistivity in the direction perpendicular to layers, a portion arises with the activation conductivity caused by the hopping between localized states. The charge-transport mechanism in Bi₂Te₃ single crystals doped with chlorine is proposed.     

Thermoelectric Properties of Cu-doped Bi<Subscript>0.4</Subscript>Sb<Subscript>1.6</Subscript>Te<Subscript>3</Subscript> Prepared by Hot Extrusion

Cu_0.003Bi_0.4Sb_1.6Te₃ alloys were prepared by using encapsulated melting and hot extrusion (HE). The hot-extruded specimens had the relative average density of 98%. The (00l) planes were preferentially oriented parallel to the extrusion direction, but the specimens showed low crystallographic anisotropy with low orientation factors. The specimens were hot-extruded at 698 K, and they showed excellent mechanical properties with a Vickers hardness of 76 Hv and a bending strength of 59 MPa. However, as the HE temperature increased, the mechanical properties degraded due to grain growth. The hot-extruded specimens showed positive Seebeck coefficients, indicating that the specimens have p-type conduction. These specimens exhibited negative temperature dependences of electrical conductivity, and thus behaved as degenerate semiconductors. The Seebeck coefficient reached the maximum value at 373 K and then decreased with increasing temperature due to intrinsic conduction. Cu-doped specimens exhibited high power factors due to relatively higher electrical conductivities and Seebeck coefficients than those of undoped specimens. A thermal conductivity of 1.00 Wm^?1 K^?1 was obtained at 373 K for Cu_0.003Bi_0.4Sb_1.6Te₃ hot-extruded at 723 K. A maximum dimensionless figure of merit, ZT _max = 1.05, and an average dimensionless figure of merit, ZT _ave = 0.98, were achieved at 373 K.     

Effect of pH on Structural and Electrical Properties of Electrodeposited Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> Thin Films

Bi₂Te₃ thin films were electrodeposited at various pH values of a bismuth nitrate and tellurium oxide plating solution. Enhancement in pH results in a decrease in grain size. Transmission electron microscopy reveals the transformation of the film morphology from dispersed nanoparticles to connected chain-like nanostructures of Bi₂Te₃ as pH is increased. Electrical characterization for samples deposited in the temperature range of 300 K to 425 K shows a fourfold increase in Seebeck coefficient, S, between its maximum and minimum value as the solution pH changes from 1 to 3.5. Such enhancement of S is attributed to the increased connectivity of the nanostructures at higher pH.     

Preparation and Thermoelectric Properties of LaGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> and SmGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript>

Thermoelectric materials are attractive since they can recover waste heat directly in the form of electricity. In this study, the thermoelectric properties of ternary rare-earth sulfides LaGd_1+x S₃ (x = 0.00 to 0.03) and SmGd_1+x S₃ (x = 0.00 to 0.06) were investigated over the temperature range of 300 K to 953 K. These sulfides were prepared by CS₂ sulfurization, and samples were consolidated by pressure-assisted sintering to obtain dense compacts. The sintered compacts of LaGd_1+x S₃ were n-type metal-like conductors with a thermal conductivity of less than 1.7 W K⁻¹ m⁻¹. Their thermoelectric figure of merit ZT was improved by tuning the chemical composition (self-doping). The optimized ZT value of 0.4 was obtained in LaGd_1.02S₃ at 953 K. The sintered compacts of SmGd_1+x S₃ were n-type hopping conductors with a thermal conductivity of less than 0.8 W K⁻¹ m⁻¹. Their ZT value increased significantly with temperature. In SmGd_1+x S₃, the ZT value of 0.3 was attained at 953 K.     

High-Performance (Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>SbTe<Subscript><Emphasis Type="Italic">x</Emphasis>/2+1.5</Subscript>)<Subscript>15</Subscript>(GeTe)<Subscript>85</Subscript> Thermoelectric Materials Prepared by Melt Spinning

A new preparation process combining melt spinning and hot pressing has been developed for the (Ag _x SbTe _x/2+1.5)₁₅(GeTe)₈₅ (TAGS-85) system. Compared with samples prepared by the traditional air-quenching and hot-pressing method, electrical conductivity and thermal conductivity are lowered. The thermoelectric performance of the TAGS-85 samples varied with changing Ag content and reached the highest ZT of 1.48 when x was 0.8 for the melt-spun sample, compared with the maximum ZT of 1.36 for the air-quenched sample. The Seebeck coefficient of the melt-spun TAGS-85 alloys was improved, while both the electrical conductivity and thermal conductivity were decreased. The net result of this process is to effectively enlarge the temperature span of ZT > 1, which will benefit industrial application.     

Features of reflection spectra of single crystals of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> solid solutions in the region of plasma effects

Reflectance spectra of single crystals of Bi₂Te₃-Sb₂Te₃ solid solutions containing 0, 10, 25, 40, 50, 60, 65, 70, 80, 90, 99.5, and 100 mol % of Sb₂Te₃ have been studied in the range of 400–4000 cm⁻¹ at the temperature T = 291 K and with orientation of the vector of the electric-field strength E perpendicular to the trigonal axis of the crystal C ₃ (E ⊥ C ₃). The shape of the spectra is characteristic of plasma reflection; the spectra include the features in the range 1250–3000 cm⁻¹ corresponding to the optical band gap E _{g opt}. The features become more pronounced as the content of Bi₂Te₃ is increased to 80 mol % in the composition of the Bi₂Te₃-Sb₂Te₃ solid solution. A further increase in the content of Sb₂Te₃ is accompanied by discontinuities in the functional dependences of the parameters characterizing the plasma oscillations of free charge carriers on the solid-solution composition and also by a sharp increase in E _{g opt}.     

Influence of Element Substitution on Corrosion Behavior of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Compounds

Atmospheric water may condense on the surface of Bi₂Te₃-based compounds constituting the Peltier module, depending on the operating environment used. In the stage of disposal, Bi₂Te₃-based compounds may come into contact with water in waste disposal sites. There are very few publications about the influence of condensed water on Peltier modules. Bi₂Te₃-Sb₂Te₃ or Bi₂Te₃-Bi₂Se₃ pseudo binary system compounds are used as p-type material or n-type material, respectively. The lattice distortion will be induced in the crystal of Bi₂Te₃-based compounds by element substitution due to the reduction in their thermal conductivity. However, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds remains unclear. In this study, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds with practical compositions has been investigated. Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 was prepared by the vertical Bridgman method. The electrochemical properties at room temperature were evaluated by cyclic voltammetry in a standard three-electrode cell. The working electrolyte was a naturally aerated 0.6 or 3.0 mass% NaCl solution. From the tendency for corrosion potential for all the samples, the corrosion sensitivity of ternary compounds was slightly higher than that of binary compounds. From the trend of current density, it was found that Bi_0.5Sb_1.5Te₃ had a corrosion resistance intermediate between Bi₂Te₃ and Sb₂Te₃. On the other hand, corrosion resistance was affected despite a small amount of Se substitution, and the corrosion resistance of Bi₂Te_2.85Se_0.15 was close to or lower than that of Bi₂Se₃. From the observation results of the corrosion products, the trends of morphology and composition of corrosion products for Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 were consistent with those of Sb₂Te₃ or Bi₂Se₃, respectively. From the results of x-ray photoelectron spectroscopy for the electrolyte after testing, the possibility that a corrosion product diffuses to the environment including the salt was suggested in Bi_0.5Sb_1.5Te₃. However, the amount of dissolved corrosion product was very low, and the chemical stability of the corrosion product was not changed or improved by element substitution.     

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in p-Type BixSb2?xTe3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Bi _x Sb_2−x Te₃ bulk alloys are known as the best p-type thermoelectric materials near room temperature. In this work, single-phase Bi _x Sb_2−x Te₃ (x = 0.2, 0.25, 0.3, 0.34, 0.38, 0.42, 0.46, and 0.5) alloys were prepared by spark plasma sintering (SPS) using mechanical alloying (MA)-derived powders. A small amount (0.1 vol.%) of SiC nanoparticles was added to improve the mechanical properties and to reduce the thermal conductivity of the alloys. The electrical resistivity decreases significantly with increasing ratio of Sb to Bi in spite of the weaker decreasing trend in Seebeck coefficient, whereby the power factor at 323 K reaches 3.14 × 10⁻³ W/mK² for a sample with x = 0.3, obviously higher than that at x = 0.5 (2.27 × 10⁻³ W/mK²), a composition commonly used for ingots. Higher thermal conductivities at low temperatures are obtained at the compositions with lower x values, but they tend to decrease with temperature. As a result, higher ZT values are obtained for Bi_0.3Sb_1.7Te₃, with a maximum ZT value of 1.23 at 423 K, about twice the ZT value (about 0.6) of Bi_0.5Sb_1.5Te₃ at the same temperature.     

Doping of the Bi<Subscript>1.9</Subscript>Sb<Subscript>0.1</Subscript>Te<Subscript>3</Subscript> solid solution with Sn impurity

In (Bi_1.9Sb_0.1)_{1 − x} Sn _x Te₃ solid solution with different contents of Sn, the electrical conductivity (σ₁₁) and the Hall (R ₁₂₃ and R ₃₂₁), Seebeck (S ₁₁ and S ₃₃), and Nernst-Ettingshausen (Q ₁₂₃ and Q ₃₂₁) coefficients have been measured. It is shown that doping with tin strongly modifies temperature dependences of the kinetic coefficients. The effect of tin on electrical homogeneity of the samples has been studied: with increasing number of Sn atoms embedded, crystals become more homogeneous. These features indicate the presence of the quasi-local states of Sn in the valence band of Bi_1.9Sb_0.1Te₃. Within a one-band model, we estimated the effective mass of the density of hole states (m _d ), the energy gap extrapolated to 0 K (E _g0 = 0.20–0.25 eV), the energy of impurity states (E _Sn ≈ 40–45 meV), and the scattering parameter (r ≈ 0.1–0.4). Numerical values of the scattering parameter indicate a mixed mechanism of scattering in the samples under investigation with dominant scattering at acoustic phonons. With increasing content of tin in the samples, the contribution of impurity scattering increases.     

Beneficial Effect of S-Filling on Thermoelectric Properties of S<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Co<Subscript>4</Subscript>Sb<Subscript>11.2</Subscript>Te<Subscript>0.8</Subscript> Skutterudite

In this work, Te-doped and S-filled S _x Co₄Sb_11.2Te_0.8 (x = 0.1, 0.15, 0.2, 0.25, 0.3, 0.4) skutterudite compounds have been prepared using solid state reaction and spark plasma sintering. Thermoelectric measurements of the consolidated samples were examined in a temperature range of 300–850 K, and the influences of S-addition on the thermoelectric properties of S _x Co₄Sb_11.2Te_0.8 skutterudites are systematically investigated. The results indicate that the addition of sulfur and tellurium is effective in reducing lattice thermal conductivity due to the point-defect scattering caused by tellurium substitutions and the cluster vibration brought by S-filling. The solubility of tellurium in skutterudites is enhanced with sulfur addition via charge compensation. The thermal conductivity decreases with increasing sulfur content. The highest figure of merit, ZT = 1.5, was obtained at 850 K for S_0.3Co₄Sb_11.2Te_0.8 sample, because of the low lattice thermal conductivity.     

Preparation and Thermoelectric Properties of Nanoporous Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Alloys

n-Type nanoporous Bi₂Te₃-based thermoelectric materials with different porosity ratios have been prepared by spark plasma sintering (SPS). The microstructure and phase morphology have been analyzed by x-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM), and the thermoelectric properties of the SPS samples have been measured. Experimental results show that the nanoporous structures lying in the sheet layers and among the plate grains of the Bi₂Te₃ bulk material can lead to an increase in the Seebeck coefficient and a decrease in the thermal conductivity, thus leading to an enhanced figure of merit.     

Improvement of Thermoelectric Power Factor of Hydrothermally Prepared Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Compared with its Solvothermally Prepared Counterpart

We report on the successful hydrothermal synthesis of Bi_0.5Sb_1.5Te₃, using water as the solvent. The products of the hydrothermally prepared Bi_0.5 Sb_1.5Te₃ were hexagonal platelets with edges of 200–1500 nm and thicknesses of 30–50 nm. Both the Seebeck coefficient and electrical conductivity of the hydrothermally prepared Bi_0.5Sb_1.5Te₃ were larger than those of the solvothermally prepared counterpart. Hall measurements of Bi_0.5Sb_1.5Te₃ at room temperature indicated that the charge carrier was p-type, with a carrier concentration of 9.47 × 10¹⁸ cm⁻³ and 1.42 × 10¹⁹ cm⁻³ for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively. The thermoelectric power factor at 290 K was 10.4 μW/cm K² and 2.9 μW/cm K² for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively.     

Effect of Chemical Composition on the Thermoelectric Properties of n-Type Bi2Te3 Alloys Fabricated by Gas Atomization and Hot Extrusion

In this research, n-type (Bi₂Te₃)_1?x (Bi₂Se₃) _x -based thermoelectric (TE) materials were produced through a gas atomization process, and subsequently hot extruded with an extrusion ratio of 10:1 at 400 °C. The effect of chemical composition on TE properties was investigated. The microstructure of all extruded bars showed a homogeneous and fine distribution of grains due to the dynamic recrystallization during the hot extrusion process. With increasing Bi₂Te₃ content, from 0.85 to 0.90, both electrical resistivity and Seebeck coefficient values were increased. The maximum figure of merit (ZT) 0.673 was obtained at room temperature for (Bi₂Te₃)₀.₉₀(Bi₂Se₃)_0.10 alloys due to them exhibiting higher seebeck coefficient and lower thermal conductivity than other compositions.     

Enhancement of Thermoelectric Figure of Merit for Bi0.5Sb1.5Te3 by Metal Nanoparticle Decoration

Introducing nanoinclusions in thermoelectric (TE) materials is expected to lower the lattice thermal conductivity by intensifying the phonon scattering effect, thus enhancing their TE figure of merit ZT. We report a novel method of fabricating Bi_0.5Sb_1.5Te₃ nanocomposite with nanoscale metal particles by using metal acetate precursor, which is low cost and facile to scale up for mass production. Ag and Cu particles of ??40?nm were successfully near-monodispersed at grain boundaries of Bi_0.5Sb_1.5Te₃ matrix. The well-dispersed metal nanoparticles reduce the lattice thermal conductivity extensively, while enhancing the power factor. Consequently, ZT was enhanced by more than 25% near room temperature and by more than 300% at 520?K compared with a Bi_0.5Sb_1.5Te₃ reference sample. The peak ZT of 1.35 was achieved at 400?K for 0.1?wt.% Cu-decorated Bi_0.5Sb_1.5Te₃.     

Effect of NiTe Nanoinclusions on Thermoelectric Properties of Bi2Te3

Metal nanoinclusions in bulk thermoelectric matrix create metal?Csemiconductor interfaces, which can result in improvement in the thermoelectric power factor due to low-energy electron filtering and a simultaneous reduction in lattice thermal conductivity due to increased phonon scattering at grain boundaries. The combined effect results in enhancement of the thermoelectric figure of merit. We report the effect of NiTe nanoinclusions in a Bi₂Te₃ matrix. The Bi₂Te₃/NiTe nanocomposite was synthesized by planetary ball milling. Different volume fractions of NiTe nanoinclusions were incorporated into the bulk (Bi₂Te₃) matrix and uniaxially hot pressed at 100?MPa and 500°C. The presence of nanoinclusions was confirmed by x-ray diffraction and transmission electron microscopy. The Seebeck coefficient, electrical conductivity, and thermal diffusivity were measured from room temperature to 150°C. The carrier concentration of the matrix (Bi₂Te₃) and the nanocomposites (NiTe/Bi₂Te₃) at room temperature were deduced from Hall-effect measurements. Addition of NiTe decreased the carrier concentration, and the power factor increased in the 1?vol.% NiTe/Bi₂Te₃ compared with inclusion-free Bi₂Te₃ matrix due to an increase in mobility.