AlGaN/GaN HEMTs器件布局对器件性能影响分析

比较了空气桥跨细栅和空气桥跨栅总线两种源连接结构的1 mm AlGaN/GaN HEMTs器件的特性,对两种结构的管芯进行了等效电路参数提取.测试了两种布局方式下的不同源场板结构器件的射频以及功率性能,比较分析表明,空气桥跨细栅的源连接方式由于有效地降低了栅漏电容以及栅源电容,比空气桥跨栅总线源连接的器件能取得更好的频率特性以及功率特性.     

高性能1mm AlGaN/GaN功率HEMTs研制

报道了基于蓝宝石衬底的高性能1mm AlGaN/GaN HEMTs功率器件.为了提高微波功率器件性能，采用新的欧姆接触和新型空气桥方案．测试表明，器件电流密度为0.784A/mm，跨导197mS/mm，击穿电压大于40V，截止态漏电较小，1mm栅宽器件的单位截止频率达到20GHz，最大振荡频率为28GHz，功率增益为11dB，功率密度为1.2W/mm,PAE为32%,两端口阻抗特性显示了在微波应用中的良好潜力．     

Ka波段AlGaN/GaN HEMT的研制

为了提高AlGaN/GaN HEMT的频率,采用了缩小源漏间距、优化栅结构和外围结构等措施设计了器件结构,并基于国内的GaN外延片和工艺完成了器件制备.测试表明所研制的AlGaN/GaN HEMT可以满足Ka波段应用.其中2×75μm栅宽AlGaN/GaN HEMT在30V漏压下的截止频率为32GHz,最大振荡频率为1...     

UV/Ozone 表面处理对AlGaN/GaN HEMTs 性能的影响

工艺过程中对晶圆表面处理对制作出高性能的AlGaN/GaN HEMT起到至关重要的作用,洁净的表面能够有效提高器件性能以及器件可靠性。本文发现通过UV/Ozone表面处理,AlGaN/GaN HEMT器件的欧姆接触以及肖特基接触的电学特性均发生明显变化,根据实验中现象以及相关实验数据,并且采用X射线光电子能谱对实验样品进行表面分析测试,着重阐述了UV/Ozone处理对晶圆表面的作用,以及其影响AlGaN/GaN HEMT器件欧姆接触特性以及肖特基接触特性的原因。     

AlN阻挡层对AlGaN/GaNHEMT器件的影响

利用低压MOCVD技术在蓝宝石衬底上生长了AlGaN/GaN异质结和AlGaN/AlN/GaN异质结二维电子气材料,采用相同器件工艺制造出了AlGaN/GaN HEMT器件和AlGaN/AlN/GaN HEMT器件.通过对两种不同器件的比较和讨论,研究了AlN阻挡层的增加对AlGaN/GaN HEMT器件性能的影响.     

Effects of the fluorine plasma treatment on low-density drain AlGaN/GaN HEMT

Low-density drain high-electron mobility transistors (LDD-HEMTs) with different F^- plasma treatment were investigated by simulations and experiments. The LDD region was performed by introducing negatively charged fluorine ions, which modified the surface field distribution on the drain side of the HEMT, and the enhancement of breakdown voltage were achieved. With the increased fluorine plasma treatment power and LDD region length, the breakdown voltage can be maximumly improved by 70%, and no severe reductions on output current and transconductance were observed. To confirm the temperature stability of the devices, annealing experiments were carried out at 400℃ for 2 min in ambient N₂. Moreover, the gate leakage current and breakdown voltage before and after annealing were compared and analyzed, respectively.     

Effects of rapid thermal annealing on ohmic contact of AlGaN/GaN HEMTs

工艺制作源漏电极为Ti/Al/Ti/Au,并在氮气气氛中对其进行快速退火,研究不同退火条件对欧姆接触的影响。具体实验过程如下：将溅射好源漏电极的外延片分为5部分,其中3片分别在700℃,750℃和800℃下快速退火30s,并相互对比得出最佳退火温度,实验结果发现750℃条件下欧姆接触最好;其余2片在750℃下分别退火25s和40s,并与前边实验750℃ 30s情况下欧姆接触比较,得出最佳退火时间为30s。我们使用传输线模式计算出电极与外延片的欧姆接触电阻率,在750℃ 30s的快速退火条件下得到最低欧姆接触电阻率为0.54 Ω mm,与其余条件下结果比较具有较好的表面形貌和边缘。从实验中我们也得到随着退火温度和退火时间的提高,欧姆接触电阻率先降低到达最低点然后开始升高的现象,为寻找GaN HEMT欧姆接触最佳条件提供了一定依据。     

F注入AlGaN/GaN增强型HEMT

The fabrication of enhancement-mode AlGaN/GaN HEMTs by fluorine plasma treatment on sapphire substrates is reported. A new method is used to fabricate devices with different fluorine plasma RF power treatments on one wafer to avoid differences between different wafers. The plasma-treated gate regions of devices treated with different fluorine plasma RF powers were separately opened by a step-and-repeat system. The properties of these devices are compared and analyzed. The devices with 150 W fluorine plasma treatment power and with 0.6 μm gate-length exhibited a threshold voltage of 0.57 V, a maximum drain current of 501 mA/mm, a maximum transconductance of 210 mS/mm, a current gain cutoff frequency of 19.4 GHz and a maximum oscillation frequency of 26 GHz. An excessive fluorine plasma treatment power of 250 W results in a small maximum drain current, which can be attributed to the implantation of fluorine plasma in the channel.     

Ka波段AlGaN/GaN HEMT栅结构仿真研究

为了研究适合Ka波段AlGaN/GaN HEMT的栅结构尺寸,借助二维器件仿真软件Silvaco Atlas,在完善仿真模型的基础上研究了Γ型栅各部分对AlGaN/GaN HEMT特性的影响,包括栅长与短沟道效应的关系、栅与沟道距离对短沟道效应和饱和漏电流的影响,以及栅金属厚度对fmax,栅场板对fT、fmax和内部电场的影响。根据典型器件结构和材料参数的仿真表明,为了提高频率并减轻短沟道效应,栅长应取0.15～0.25μm;减小栅与沟道的距离可略微改善短沟道效应,但会明显降低器件的饱和漏电流,综合考虑栅调制能力、饱和漏电流、短沟道效应三个方面,栅与沟道距离应取10～20nm;为了提高fmax,栅金属厚度应大于0.4μm;缩小栅场板长度可有效提高器件的频率,兼顾Ka波段应用和提高击穿电压,栅场板长度应在0.3～0.4μm左右。仿真得出的器件性能随结构参数的变化趋势以及尺寸数据对于Ka波段AlGaN/GaN HEMT的研究具有参考意义。     

Effect of gate length on DC performance of AlGaN/GaN HEMTs grown by MBE

The DC performance of AlGaN/GaN high electron mobility transistors grown by plasma-assisted molecular beam epitaxy was investigated for gate lengths in the range 0.1–1.2 μm. On 0.25 μm gate length devices we obtained 40 V_DS operation with >50 mA peak I_D. The peak drain current density was 0.44 A/mm for 100 μm gate width devices with 1.2 μm gate lengths. The extrinsic transconductance (g_m) decreased with both gate length and gate width and was 75 mS/mm for all gate widths for 0.25 μm devices. E-beam written gates typically produced a slightly lower Schottky barrier height than optically patterned gates.     

Physics-based numerical simulation and device characterizations of AlGaN/GaN HEMTs with temperature effects

The research presents AlGaN/GaN HEMTs device characterizations at different temperatures using physics-based numerical simulation. Industry standard simulation tool Silvaco ATLAS is used to characterize the various electronic properties of the device. An extensive theoretical overview is done to achieve the most comprehensive values for GaN and AlGaN properties, as discussed in the paper. This research is mainly focused on simulation of temperature dependent device performances as well as on some other material properties that are not well defined in ATLAS. Energy bandgap, density of states, saturation velocities, surface traps, polarization effect, carrier lifetime and mobility, permittivity, effective Richardson's constant, and donor and acceptor energy levels are considered as critical parameters for predicting temperature effect in ALGaN/GaN HEMT. Various aspects of device performance are analyzed at high temperature along with the different bias configurations.     

高频功率AlGaN/GaN HEMT 的栅结构优化

本文研究了栅帽、栅源间距对AlGaN/GaN HEMT性能的影响。基于研究结果得出了优化高频功率AlGaN/GaN HEMT栅结构的方法。缩小栅场板可以有效提高器件的增益、截止频率（ft）、最大震荡频率（fmax）。通过减小栅场板长度,栅长0.35 器件的ft达到了30GHz、fmax达到了80GHz。采用tao型栅（栅帽偏向源侧）或者增加栅金属厚度还可以进一步优化 。缩小栅源的距离可以提高饱和漏电流和击穿电压,从而提高器件的输出功率。     

AlGaN/GaN HEMT电流崩塌效应研究进展

简要回顾了 Al Ga N/Ga N HEMT器件电流崩塌效应研究的进展 ,着重阐述了虚栅模型、应力模型等几种解释电流崩塌效应形成机理的模型和器件钝化、生长盖帽层等减小电流崩塌效应的措施。     

AlGaN/GaN HEMT器件的研制

介绍了AlGaN/GaNHEMT器件的研制及室温下器件特性的测试.漏源欧姆接触采用Ti/Al/Pt/Au ,肖特基结金属为Pt/Au .器件栅长为1μm ,获得的最大跨导为12 0mS/mm ,最大的漏源饱和电流密度为0 95A/mm .     

AlGaN/GaN HEMT高场应力退化及紫外光辐照的研究

采用不同的应力偏压发现器件特性的下降程度随应力偏置电压的增大而增大.经过3×104s 40V高场应力后,蓝宝石衬底 AlGaN/GaN HEMT饱和漏电流下降5.2%,跨导下降7.6%.从器件直流参数的下降分析了应力后的特性退化现象并与连续直流扫描电流崩塌现象进行了对比,同时观察了紫外光照对应力后器件特性退化的恢复作用.直流扫描电流崩塌现象在紫外光照下迅速消除,但是紫外光照不能恢复高场应力造成的特性退化.     

基于AlGaN/GaN HEMT的X波段内匹配功率合成放大器的设计

利用内匹配和功率合成技术设计了X波段AlGaN/GaN HEMT功率合成放大器.电路包含有四个AlGaN/GaN HEMT和制作在Al2O3陶瓷基片上的输入输出匹配电路.在偏置条件VDS=30 V,IDS=700 mA时8 GHz测出连续波饱和输出功率达到Pat=40 dBm(10 W),最大PAE=37.44%,线性增益9 dB.     

AlGaN/GaN HEMT高场应力退化及紫外光辐照的研究

采用不同的应力偏压发现器件特性的下降程度随应力偏置电压的增大而增大.经过3×104s 40V高场应力后,蓝宝石衬底 AlGaN/GaN HEMT饱和漏电流下降5.2%,跨导下降7.6%.从器件直流参数的下降分析了应力后的特性退化现象并与连续直流扫描电流崩塌现象进行了对比,同时观察了紫外光照对应力后器件特性退化的恢复作用.直流扫描电流崩塌现象在紫外光照下迅速消除,但是紫外光照不能恢复高场应力造成的特性退化.     

SiN钝化前的NF3等离子体处理对AlGaN/GaN HEMT性能的影响

研究了SiN钝化前利用感应耦合等离子体（ICP）对AlGaN/GaN HEMT表面进行NF3等离子体处理对器件性能的影响. 结果表明,运用低能量的NF3等离子体处理钝化前的AlGaN/GaN HEMT表面能有效抑制器件电流崩塌,而器件直流及微波小信号特性则未受影响. 微波功率测试表明,经过6min NF3等离子体处理的AlGaN/GaN HEMT在2GHz, 30V工作电压下达到6.15W/mm的输出功率密度,而未经过处理的器件只达到1.82W/mm的输出功率密度.     

一个8 GHz基于AlGaN/GaN HEMT的内匹配电路

论述了一个在8 GHz下基于AlGaN/GaN HEMT功率放大器HMIC的设计、制备与测试.该电路包含了1个10×100 μm的AlGaN/GaN HEMT和输入输出匹配电路.在偏置条件为VDS=40 V、IDS=0.16 A时输出连续波饱和功率在8 GHz达到36.5 dBm(4.5 W),PAE为60%,线性增益10 dB;在偏置条件为VDS=30 V、IDS=0.19 A时输出连续波饱和功率在8 GHz达到35.6 dBm(3.6 W),PAE为47%,线性增益9 dB.     

X波段AlGaN/GaN HEMTs Γ栅场板结构研究

基于SiC衬底成功研制X波段0.25 μm栅长带有r栅场板结构的AlGaN/GaN HEMT,设计场板(field plate)长度为0.4 μm,0.6μm,0.7μm,0.9μm.研究了r栅场板长度及不同漏偏压下对器件直流,小信号特性及大信号的影响.器件直流I-V及转移特性并不依赖场板长度变化,增加场板长度器件击穿电压提高可达108 V,器件截止频率及振荡频率下降,输出功率大幅度提高,结合器件小信号提参结果分析.8 GHz下,总栅宽1 mm,场板长度为0.9 μm的器件,连续波输出功率密度7.11 W/mm,功率附加效率(PAE)35.31%,相应线性增益10.25 dB.