Hole tunneling current through oxynitride/oxide stack and the stackoptimization for p-MOSFETs

A systematic study on hole-tunneling current through both oxynitride and oxynitride/oxide (N/O) stack is for the first time presented based on a physical model. The calculations are in good agreement with the available experimental data. With a given equivalent oxide thickness (EOT), and under typical operating gate voltages (|Vg|<2 V), hole-tunneling current (essentially the gate current) is found to be lowest through the oxynitride or N/O stack with ~33% of nitrogen (N). An optimized N/O stack structure with 33% (atomic percentage) nitrogen and with a 3 Å oxide layer for keeping acceptable channel interface quality is proposed to project the N/O gate dielectrics scaling limit using in MOSFETs     

Atomic Layer-deposited Si-nitride/SiO/sub 2/ stack gate dielectrics for future high-speed DRAM with enhanced reliability

Atomic layer-deposited (ALD) Si-nitride/SiO/sub 2/ stack gate dielectrics were applied to high-performance transistors for future scaled DRAMs. The stack gate dielectrics of the peripheral pMOS transistors excellently suppress boron penetration. ALD stack gate dielectrics exhibit only slightly worse negative-bias temperature instability (NBTI) characteristics than pure gate oxide. Enhanced reliability in NBTI was achieved compared with that of plasma-nitrided gate SiO/sub 2/. Memory-cell (MC) nMOS transistors with ALD stack gate dielectrics show slightly smaller junction leakage than those with plasma-nitrided gate SiO/sub 2/ in a high-drain-voltage region, and have identical junction leakage characteristics to transistors with pure gate oxide. MCs having transistors with ALD stack gate dielectrics and those with pure gate oxide have the identical retention-time distribution. Taking the identical hole mobility for the transistors with ALD stack gate dielectrics to that for the transistors with pure gate oxide both before and after hot carrier injection (previously reported) into account, the ALD stack dielectrics are a promising candidate for the gate dielectrics of future high-speed, reliable DRAMs.     

A study of the role of HBr and oxygen on the etch selectivity and the post-etch profile in a polysilicon/oxide etch using HBr/O2 based high density plasma for advanced DRAMs

The role of HBr and oxygen on the etch selectivity and the post-etch profile in a polysilicon/oxide etch using HBr/O₂ based high density plasma was studied. HBr/O₂-based polysilicon etch process used in this study seems to be highly selective to the underlying oxide and produce a dielectric fill-friendly post-etch profile depending on the flow rates of HBr and oxygen. When appropriate amounts of HBr and oxygen (∼30 sccm of HBr and ∼3 sccm of oxygen) are present in the etch plasma, brominated silicon oxide seems to be deposited on the original gate oxide and the gate stack sidewall from the reaction of SiBr_x (reaction product during polysilicon etch step) and oxygen during the HBr/O₂-based oxide etch process. The deposited brominated oxide on the thin gate oxide seems to make the HBr/O₂-based plasma etch process extremely selective to the thin gate oxide by protecting the underlying gate oxide. The deposited brominated oxide on the gate stack sidewall seems to prevent the notching by protecting the sidewall during gate stack etching. The etch rate of the brominated oxide seems to be much faster than that of the thermal oxide during the 200:1 diluted HF cleaning. However, the deposited brominated oxide on the thin gate oxide and the gate stack sidewall during the plasma etching survived the following 1 min 200:1 diluted HF cleaning, as was observed in a TEM micrograph (Fig. 2(a)).     

恒压应力下超薄Si_3N_4/SiO_2叠层栅介质与SiO_2栅介质寿命比较

以等效氧化层厚度(EOT)同为2.1nm的纯SiO2栅介质和Si3N4/SiO2叠层栅介质为例,给出了恒定电压应力下超薄栅介质寿命预测的一般方法,并在此基础上比较了纯SiO2栅介质和Si3N4/SiO2叠层栅介质在恒压应力下的寿命.结果表明,Si3N4/SiO2叠层栅介质比同样EOT的纯SiO2栅介质有更长的寿命,这说明Si3N4/SiO2叠层栅介质有更高的可靠性.     

BE-SONOS flash memory along with metal gate and high-k dielectrics in tunnel barrier and its impact on charge retention dynamics

We investigate the effect of a high-k dielectric in the tunnel layer to improve the erase speed-retention trade-off. Here, the proposed stack in the tunnel layer is AlLaO₃/HfAlO/SiO₂. These proposed materials possess low valence band offset with high permittivity to improve both the erase speed and retention time in barrier engineered silicon-oxide-nitride-oxide-silicon(BE-SONOS). In the proposed structure HfAlO and AlLaO₃ replace Si₃N₄ and the top SiO₂ layer in a conventional oxide/nitride/oxide(ONO) tunnel stack. Due to the lower conduction band offset(CBO) and high permittivity of the proposed material in the tunnel layer, it offers better program/erase(P/E) speed and retention time. In this work the gate length is also scaled down from 220 to 55 nm to observe the effect of high-k materials while scaling, for the same equivalent oxide thickness(EOT). We found that the scaling down of the gate length has a negligible impact on the memory window of the devices. Hence, various investigated tunnel oxide stacks possess a good memory window with a charge retained up to 87.4%(at room temperature) after a period of ten years. We also examine the use of a metal gate instead of a polysilicon gate, which shows improved P/E speed and retention time.     

Plasma-Induced Damage in High-k/Metal Gate Stack Dry Etch

Plasma-based dry etch is used as the industry standard gate etch in conventional CMOS fabrication flow. However, past studies indicate that plasma-induced dry etch may impact device performance. The current research trend toward replacing conventional silicon dioxide and polysilicon gate stacks with high-k/metal gate stacks introduces a new challenge: development of new dry etch processes for critical new metals and their alloys. In this letter, a comparative study in the context of device performance has been conducted to compare dry etch versus wet etch for gate stack etch of hafnium oxide/tantalum silicon nitride gate stack. It has been found that the dry-etched gate stack exhibit significantly more gate leakage current and poorer uniformity in threshold-voltage distribution     

Investigation of hole-tunneling current through ultrathinoxynitride/oxide stack gate dielectrics in p-MOSFETs

The systematic investigation of hole tunneling current through ultrathin oxide, oxynitride, oxynitride/oxide (N/O) and oxide/oxynitride/oxide (ONO) gate dielectrics in p-MOSFETs using a physical model is reported for the first time. The validity of the model is corroborated by the good agreement between the simulated and experimental results. Under typical inversion biases (|VG|<2 V), hole tunneling current is lower through oxynitride and oxynitride/oxide with about 33 at.% N than through pure oxide and nitride gate dielectrics. This is attributed to the competitive effects of the increase in the dielectric constant, and hence dielectric thickness, and decrease in the hole barrier height at the dielectric/Si interface with increasing with N concentration for a given electrical oxide thickness (EOT). For a N/O stack film with the same N concentration in the oxynitride, the hole tunneling current decreases monotonically with oxynitride thickness under the typical inversion biases. For minimum gate leakage current and maintaining an acceptable dielectric/Si interfacial quality, an N/O stack structure consisting of an oxynitride layer with 33 at.% N and a 3 Å oxide layer is proposed. For a p-MOSFET at an operating voltage of -0.9 V, which is applicable to the 0.7 μm technology node, this structure could be scaled to EOT=12 Å if the maximum allowed gate leakage current is 1 A/cm² and EOT=9 Å if the maximum allowed gate leakage current is 100 A/cm²     

Performance and reliability of low-temperature polysilicon TFT with a novel stack gate dielectric and stack optimization using PECVD nitrous oxide plasma

This paper proposes a novel tetraethylorthosilicate (TEOS)/oxynitride stack gate dielectric for low-temperature poly-Si thin-film transistors, composed of a plasma-enhanced chemical vapor deposition (PECVD) thick TEOS oxide/ultrathin oxynitride grown by PECVD N/sub 2/O plasma. The novel stack gate dielectric exhibits a very high electrical breakdown field of 8.5 MV/cm, which is approximately 3 MV/cm higher than traditional PECVD TEOS oxide. The novel stack oxide also has better interface quality, lower bulk-trap density, and higher long-term reliability than PECVD TEOS dielectrics. These improvements are attributed to the formation of strong Si/spl equiv/N bonds of high quality ultra-thin oxynitride grown by PECVD N/sub 2/O plasma, and the reduction in the trap density at the oxynitride/poly-Si interface.     

Electrical characterization and process control of cost-effective high-k aluminum oxide gate dielectrics prepared by anodization followed by furnace annealing

A cost-effective technique was introduced to prepare ultrathin aluminum oxide (Al/sub 2/O/sub 3/) gate dielectrics with equivalent oxide thickness (EOT) down to 14 /spl Aring/. Al/sub 2/O/sub 3/ was fabricated by anodic oxidation (anodization) of ultrathin Al films at room temperature in deionized water and then furnace annealed at 650/spl deg/C in N/sub 2/ ambient. Both dc and dac (dc superimposed with ac) anodization techniques were investigated. Effective dielectric constant of k/spl sim/7.5 and leakage current of 2-3 orders of magnitude lower than SiO/sub 2/ are observed. The conduction mechanism in Al/sub 2/O/sub 3/ gate stack is shown to be Fowler-Nordheim (F-N) tunneling. Saturated current behavior in the inversion region of MOS capacitor is observed. It is found that the saturation current is sensitive to interface state capacitance and can be used as an efficient way to evaluate the Al/sub 2/O/sub 3/ gate stack/Si-substrate interfacial property. An optimal process control for preparing Al/sub 2/O/sub 3/ gate dielectrics with minimized interface state capacitance via monitoring the inversion saturation current is demonstrated.     

TDDB and polarity-dependent reliability of high-quality, ultrathin CVD HfO/sub 2/ gate stack with TaN gate electrode

In this letter, we present a comprehensive study on longterm reliability of ultrathin TaN-gated chemical vapor deposition gate stack with EOT=8.5-10.5. It is found that, due to the asymmetric band structure of HfO/sub 2/ gate stack with an interfacial layer, the HfO/sub 2/ gate stack shows polarity-dependent leakage current, critical defect density, and defect generation rate, under gate and substrate injection. However, no such polarity dependence of time-to-breakdown (T/sub BD/) is observed when T/sub BD/ is plotted as a function of gate voltage. The 10-year lifetime of an HfO/sub 2/ gate stack is projected to be Vg=-1.63 V for the equivalent oxide thickness (EOT) =8.6 and Vg=-1.88 V for EOT=10.6 at 25/spl deg/C. These excellent reliability characteristics are attributed to reduced leakage current of HfO/sub 2/ gate stack with physically thicker films that result in larger critical defect density and Weibull slope to that of SiO/sub 2/ for the same EOT. However, at 150/spl deg/C, and with area scaling to 0.1 cm/sup 2/ and low percentile of 0.01%, the maximum allowed voltages are projected to Vg=-0.6 V and -0.75 V for EOT of 8.6, and 10.6, respectively.     

Atomic-layer-deposited silicon-nitride/SiO2 stack––a highly potential gate dielectrics for advanced CMOS technology

An extremely thin (2 monolayers) silicon nitride layer has been deposited on thermally grown SiO₂ by an atomic-layer-deposition (ALD) technique and used as gate dielectrics in metal–oxide–semiconductor (MOS) devices. The stack dielectrics having equivalent oxide thickness (T_eq=2.2 nm) efficiently reduce the boron diffusion from p⁺ poly-Si gate without the pile up of nitrogen atoms at the SiO₂/Si interface. The ALD silicon nitride is thermally stable and has very flat surface on SiO₂ especially in the thin (<0.5 nm) thickness region.An improvement has been obtained in the reliability of the ALD silicon-nitride/SiO₂ stack gate dielectrics compared with those of conventional SiO₂ dielectrics of identical thickness. An interesting feature of soft breakdown free phenomena has been observed only in the proposed stack gate dielectrics. Possible breakdown mechanisms are discussed and a model has been proposed based on the concept of localized physical damages which induce the formation of conductive filaments near both the poly-Si/SiO₂ and SiO₂/Si-substrate interfaces for the SiO₂ gate dielectrics and only near the SiO₂/Si-substrate interface for the stack gate dielectrics.Employing annealing in NH₃ at a moderate temperature of 550 °C after the ALD of silicon nitride on SiO₂, further reliability improvement has been achieved, which exhibits low bulk trap density and low trap generation rate in comparison with the stack dielectrics without NH₃ annealing.Because of the excellent thickness controllability and good electronic properties, the ALD silicon nitride on a thin gate oxide will fulfill the severe requirements for the ultrathin stack gate dielectrics for sub-0.1 μm complementary MOS (CMOS) transistors.     

Electrical characteristics of low temperature polysilicon TFT with a novel TEOS/oxynitride stack gate dielectric

This investigation is the first to demonstrate a novel tetraethylorthosilicate (TEOS)/oxynitride stack gate dielectric for low-temperature poly-Si (LTPS) thin film transistors (TFTs), composed of a plasma-enhanced chemical vapor deposition (PECVD) thick TEOS oxide/ultrathin oxynitride grown by PECVD N/sub 2/O-plasma. The stack oxide shows a very high electrical breakdown field of 8.4 MV/cm, which is approximately 3 MV/cm larger than traditional PECVD TEOS oxide. The field effective mobility of stack oxide LTPS TFTs is over 4 times than that of traditional TEOS oxide LTPS TFTs. These improvements are attributed to the high quality N/sub 2/O-plasma grown ultrathin oxynitride forming strong Si/spl equiv/N bonds, as well as to reduce the trap density in the oxynitride/poly-Si interface.     

Tunneling leakage current in ultrathin (<4 nm) nitride/oxidestack dielectrics

The leakage current in high-quality ultrathin silicon nitride/oxide (N/O) stack dielectric is calculated based on a model of one-step electron tunneling through both the nitride and the oxide layers. The results show that the tunneling leakage current in the N/O stack is substantially lower than that in the oxide layer of the same equivalent oxide thickness (EOT). The theoretical leakage current in N/O stack has been found to be a strong function of the nitride/oxide EOT ratio: in the direct tunneling regime, the leakage current decreases monotonically as the M/O ratio increases, while in the Fowler-Nordheim regime the lowest leakage current is realized with a N/O EOT ratio of 1:1. Due to the asymmetry of the N/O barrier shape, the leakage current under substrate injection is higher than that under gate injection, although such a difference becomes smaller in the lower voltage regime. Experimental data obtained from high quality ultrathin N/O stack dielectrics agree well with calculated results     

Impact of metal work function on memory properties of charge-trap flash memory devices using fowler-nordheim P/E mode

This letter reports the impact of metal work function (/spl Phi//sub M/) on memory properties of charge-trap-Flash memory devices using Fowler-Nordheim program/erase mode. For eliminating electron back tunneling and hole back tunneling through the blocking oxide during an program/erase operation, a gate with /spl Phi//sub M/ of 5.1-5.7 eV on an Al/sub 2/O/sub 3/-SiN-SiO/sub 2/ (ANO) stack is necessary. Compared to a thickness optimized n/sup +/ poly-Si/ONO stack, a high-work-function gate on an ANO stack shows dramatic improvements in retention versus minimum erase state.     

A high-quality stacked thermal/LPCVD gate oxide technology for ULSI

By stacking thermal and high-quality LPCVD (low-pressure chemical vapor deposition) SiO₂ films, gate oxides with very low defect densities are demonstrated. Whereas previous reports suggested that a thick layer of LPCVD oxide can improve the stacked gate oxide defect density, it is demonstrated that even 25 Å of LPCVD oxide is sufficient to dramatically reduce the defect density compared to thermal oxide films. The projected scaling limit for this technology is estimated to be as low as 70 Å for the total stack thickness. An optimized thermal/LPCVD oxide technology is very promising as the gate dielectric for sub-half-micrometer CMOS technology     

NMOS Compatible Work Function of TaN Metal Gate With Gadolinium Oxide Buffer Layer on Hf-Based Dielectrics

Reduction in effective work function (EWF) of midgap-tantalum nitride (TaN) metal gate with gadolinium-oxide buffer layer on Hafnium-based high-$kappa$gate stack has been demonstrated. EWF of 4.2 eV is achieved for TaN with a bilayer arrangement of$hboxGd_2 O_3/hboxHfSiO_x$dielectric. By using Gd–Si cosputtered layer on$hboxHfO_2$, a reduction in EWF to nMOS compatible value of 4.05 eV is obtained. Electrical and material characterization indicate that the conversion of gadolinium to gadolinium oxide and presence of silicon in the high-$kappa$layer are responsible for the EWF shift. nMOSFETs with improved output current, transconductance, and channel electron mobility highlight the approach of using gadolinium in the gate stack.     

MOSFET characteristics with poly-Si/HfAlON gate stacks using ultra-thin UV-ozone interfacial oxide

This paper conducts a comprehensive evaluation of the electrical characteristics of the poly-silicon gated n-channel metal-oxide-semiconductor field-effect-transistor (nMOSFET) with hafnium-aluminum-oxynitride (HfAlON) gate dielectric with interfacial ultraviolet-ozone (UV-O₃) oxide or chemical oxide. Interfacial UV-O₃ oxide exhibits well-controlled interfacial properties due to self-saturated growth and thick-oxide-comparable density, which is beneficial to suppress interfacial re-oxidation and reduces surface roughness. Compared with interfacial chemical oxide, the interfacial UV-O₃ oxide obviously improves both gate insulating and interface characteristics, including breakdown voltage increments, reduced gate leakage current, and as-deposited traps. In addition, the HfAlON gate stack with UV-O₃ interface oxide also shows encouraging nMOSFET device performances, with a small subthreshold swing, high electron mobility, saturation drain current, and negligible stress-induced trap generation. The results clearly suggest that the high-density interfacial UV-O₃ oxide possess a high potential to be integrated with further high-k dielectric applications.     

Dual-metal gate CMOS technology with ultrathin silicon nitride gatedielectric

We report the first demonstration of a dual-metal gate complementary metal oxide semiconductor (CMOS) technology using titanium (Ti) and molybdenum (Mo) as the gate electrodes for the N-metal oxide semiconductor field effect transistors (N-MOSFETs) and P-metal oxide semiconductor field effect transistors (P-MOSFETs), respectively. The gate dielectric stack consists of a silicon oxy-nitride interfacial layer and a silicon nitride (Si₃N₄) dielectric layer formed by a rapid-thermal chemical vapor deposition (RTCVD) process. C-V characteristics show negligible gate depletion. Carrier mobilities comparable to that predicted by the universal mobility model for silicon dioxide (SiO₂) are observed     

The fabrication and dry etching of poly-Si/TaN/Mo gate stack in the metal inserted poly-Si stack structure

The Mo-based metal inserted poly-Si stack (MIPS) structure is an appropriate choice for metal gate and high-k integration in sub-45 nm gate-first CMOS device. A novel metal nitride layer of TaN or AlN with high thermal stability has been introduced between Mo and poly-Si as a barrier material to avoid any reaction of Mo during poly-Si deposition. After Mo-based MIPS structure is successfully prepared, dry etching of poly-Si/TaN/Mo gate stack is studied in detail. The three-step plasma etching using the Cl₂/HBr chemistry without soft landing step has been developed to attain a vertical poly-Si profile and a reliable etch-stop on the TaN/Mo metal gate. For the etching of TaN/Mo gate stack, two methods using BCl₃/Cl₂/O₂/Ar plasma are presented to get both vertical profile and smooth etched surface, and they are critical to get high selectivity to high-k dielectric and Si substrate. In addition, adding a little SF₆ to the BCl₃/O₂/Ar plasma under the optimized conditions is also found to be effective to smoothly etch the TaN/Mo gate stack with vertical profile.     

Hafnium silicate as control oxide in non-volatile memories

SONOS-type MIS capacitors with hafnium silicate as a control oxide are characterized and compared to devices featuring a conventional SONOS gate stack. Write operation is comparable for both gate stack types. Erase operation for the devices with hafnium silicate is improved since the parasitic injection of electrons from the gate is suppressed due to the low electric field in the high-k material. This reduction in leakage current through the gate enhances oxide stability. However, measurements indicate that charge retention for the gate stack with hafnium silicate is degraded for high charge densities. Band bending of the control oxide under high electric fields increases the tunneling probability for trapped charges. Additionally, initial flatband voltage decay is observed due to charge trapping in the hafnium silicate layer. Reducing the thickness of the hafnium silicate layer is possible, maintaining favorable erase properties while minimizing the charge decay rate during retention.