Effective formation of interface controlled Y2O3 thin film on Si(1 0 0) in a metal-(ferroelectric)-insulator-semiconductor structure

Yttrium was deposited on the chemical oxide of Si and annealed under vacuum to control the interface for the formation of Y₂O₃ as an insulating barrier to construct a metal-ferroelectric-insulator-semiconductor structure. Two different pre-annealing temperatures of 600 and 700 °C were chosen to investigate the effect of the interface state formed after the pre-annealing step on the successive formation of Y₂O₃ insulator and Nd₂Ti₂O₇ (NTO) ferroelectric layer through annealing under an oxygen atmosphere at 800 °C. Pre-anneal treatments of Y-metal/chemical-SiO₂/Si at 600 and 700 °C induced a formation of Y₂O₃ and Y-silicate, respectively. The difference in the pre-anneal temperature induced almost no change in the electrical properties of the Y₂O₃/interface/Si system, but degraded properties were observed in the NTO/Y₂O₃/interface/Si system pre-annealed at 600 °C when compared with the sample pre-annealed at 700 °C. C-V characteristics of the NTO/Y₂O₃/Si structured system showed a clockwise direction of hysteresis, and this gap could be used as a memory window for a ferroelectric-gate. A smaller hysteric gap and electrical breakdown values were observed in the NTO/Y₂O₃/Si system pre-annealed at 600 °C, and this was due to an unintentional distribution of the applied field from the presence of an interfacial layer containing Y-silicate and SiO₂ phases.     

Epitaxial growth of Dy2O3 thin films on epitaxial Dy-germanide films on Ge(0 0 1) substrates

Ultra-thin films of Dy are grown on Ge(0 0 1) substrates by molecular beam deposition near room temperature and immediately annealed for solid phase epitaxy at higher temperatures, leading to the formation of DyGe_x films. Thin films of Dy₂O₃ are grown on the DyGe_x film on Ge(0 0 1) substrates by molecular beam epitaxy. Streaky reflection high energy electron diffraction (RHEED) patterns reveal that epitaxial DyGe_x films grow on Ge(0 0 1) substrates with flat surfaces. X-ray diffraction (XRD) spectrum suggests the growth of an orthorhombic phase of DyGe_x films with (0 0 1) orientations. After the growth of Dy₂O₃ films, there is a change in RHEED patterns to spotty features, revealing the growth of 3D crystalline islands. XRD spectrum shows the presence of a cubic phase with (1 0 0) and (1 1 1) orientations. Atomic force microscopy image shows that the surface morphology of Dy₂O₃ films is smooth with a root mean square roughness of 10 Å.     

Controllable nanostructures on La0.7Sr0.3MnO3 thin film surfaces formed by scanning tunneling microscopy

Nanoscale structuring on La_0.7Sr_0.3MnO₃ (LSMO) thin film surfaces has been performed by scanning tunneling microscopy (STM) under ambient conditions. From line etching experiments we found that the line-depth increases in a stepwise fashion with increasing bias voltage. It also increases with decreasing scan speed and increasing scan repetition. We observed that the line-depth is an integral multiple of the LSMO out-of-plane lattice constant about 0.4 nm. Lateral structure with minimum feature size of 1 nm is possible to obtain. In addition, a four-level inverse-pyramid structure has been created on LSMO thin film surfaces. Our work shows the feasibility of using STM to fabricate controllable and complex nanostructures in LSMO thin film.     

Investigation of high-K gate stacks with epitaxial Gd2O3 and FUSI NiSi metal gates down to CET=0.86 nm

Novel gate stacks with epitaxial gadolinium oxide (Gd₂O₃) high-k dielectrics and fully silicided (FUSI) nickel silicide (NiSi) gate electrodes are investigated. Ultra-low leakage current densities down to 10^–7 A cm^–2 are observed at a capacitance equivalent oxide thickness of CET=1.8 nm. The influence of a titanium nitride (TiN) capping layer during silicidation is studied. Furthermore, films with an ultra-thin CET of 0.86 nm at a Gd₂O₃ thickness of 3.1 nm yield current densities down to 0.5 A cm⁻² at V_g=+1 V. The extracted dielectric constant for these gate stacks ranges from k=13 to 14. These results emphasize the potential of NiSi/Gd₂O₃ gate stacks for future material-based scaling of CMOS technology.     

N2 effect on GaAs etching at 150 mTorr capacitively-coupled Cl2/N2 plasma

The role of N₂ on GaAs etching at 150 mTorr capacitively-coupled Cl₂/N₂ plasma is reported. A catalytic effect of N₂ was found at 20-25% N₂ composition in the Cl₂/N₂ discharges. The peak intensities of the Cl₂/N₂ plasma were monitored with optical emission spectroscopy (OES). Both atomic Cl (725.66 nm) and atomic N (367.05 nm) were detected during the Cl₂/N₂ plasma etching. With the etch rate and OES results, we developed a simple model in order to explain the etch mechanism of GaAs in the high pressure capacitively-coupled Cl₂/N₂ plasma as a function of N₂ ratio. If the plasma chemistry condition became positive ion-deficient at low % N₂ or reactive chlorine-deficient at high % N₂ in the Cl₂/N₂ plasma, the GaAs etch rate is reduced. However, if the plasma had a more balanced ratio of Cl₂/N₂ (i.e. 20-25% N₂) in the plasma, much higher etch rates (up to 150 nm/min) than that in pure Cl₂ (50 nm/min) were produced due to synergetic effect of neutral chlorine adsorption and reaction, and positive ion bombardment. Pure Cl₂ etching produced 14 nm of RMS surface roughness of GaAs. Introduction of ?20% N₂ gas in Cl₂/N₂ discharges significantly reduced the surface roughness to 2-4 nm. SEM photos showed that the morphology of photoresist mask was strongly degraded. Etch rate of GaAs slightly increased from 10 to 40 nm/min when RIE chuck power changed from 10 to 150 W at 12 sccm Cl₂/8 sccm N₂ plasma condition. The surface roughness of GaAs etched at 12 sccm Cl₂/8 sccm N₂ plasma was 2-3 nm.     

Excellent performance of gas sensor based on In2O3-Fe2O3 nanotubes

In₂O₃-Fe₂O₃ nanotubes are synthesized by an electrospinning method. The as-synthesized materials are characterized by scanning electron microscope and X-ray powder diffraction. The gas sensing results show that In₂O₃-Fe₂O₃ nanotubes exhibit excellent sensing properties to acetone and formaldehyde at different operating temperatures. The responses of gas sensors based on In₂O₃-Fe₂O₃ nanotubes to 100 ppm acetone and 100 ppm formaldehyde are 25 (240℃) and 15 (260℃), and the response/recovery times are 3/7 s and 4/7 s, respectively. The responses of In₂O₃-Fe₂O₃ nanotubes to 1 ppm acetone (240℃) and formaldehyde (260℃) are 3.5 and 1.8, respectively. Moreover, the gas sensor based on In₂O₃-Fe₂O₃ nanotubes also possesses an excellent selectivity to acetone and formaldehyde.     

用于GaAs射频集成电路的不同厚度氧化铝MIM 电容的研究

本文研究了不同厚度的氧化铝对MIM电容直流和射频特性的影响。在1MHz下,对于20nm氧化铝MIM电容,其拥有3850 pF/mm₂的高电容密度和可接受的681 ppm/V₂的VCC-α电压系数。1MHz时突出的74 ppm/V₂VCC-α电压系数,8.2GHz谐振频率以及2GHz时41的Q值可以从100nm氧化铝MIM电容获得。采用GaAs工艺以及原子层淀积制造的高性能ALD氧化铝MIM电容很有可能成为GaAs射频集成电路很有前景的候选器件。     

Influence of post deposition annealing on Y2O3-gated GaAs MOS capacitors and their reliability issues

The feasibility of employing yttrium oxide (Y₂O₃) as high-k gate dielectrics for GaAs metal-oxide-semiconductor (MOS) devices has been investigated. MOS capacitors were fabricated using RF-sputtered deposited Y₂O₃ films on NH₄OH treated n-GaAs substrate. Indeed high-k (Y₂O₃)/GaAs MOS capacitors exhibiting fairly good electrical characteristics, for instance, especially low leakage current density, low hysteresis and allowable density of interface states, have been achieved. The effects of several annealing treatments on Y₂O₃-gated GaAs MOS capacitors have been investigated in order to optimize the process conditions. A decrease in accumulation capacitance (C_acc) following PDA effectively increases the equivalent oxide thickness (EOT), which is predicted to be correlated with the growth and continuous increase in the physical thickness of a lower-k inter-layer sandwiched between Y₂O₃ and GaAs. However, leakage currents and interface trap densities are reduced with higher values of annealing temperature. The variation of current density with an equivalent oxide thickness (EOT) has also been investigated.     

Co3O4/Fe2O3异质结复合材料的制备及其紫外光光电探测性能

分别采用旋涂法和水热法在FTO衬底上制备Co₃O₄种子层和Co₃O₄薄膜,再在Co₃O₄薄膜上水热生长Fe₂O₃纳米棒,获得了高质量的Co₃O₄/Fe₂O₃异质结复合材料。通过改变Fe₂O₃前驱体溶液浓度来改变异质结复合材料中Fe₂O₃组分的含量。结果表明,Fe₂O₃纳米棒覆盖在呈网状结构的Co₃O₄薄膜上,随着Fe₂O₃前驱体溶液浓度即Fe₂O₃组分含量的增加,Co₃O₄/Fe₂O₃异质结复合材料对紫外光的响应逐渐增强,当Fe₂O₃前驱体溶液浓度为0.015mol/L时,异质结复合材料有着很好的光电稳定性,并表现出较高的响应率(12.5mA/W)和探测率(4.4×10¹⁰Jones)。     

First investigation of metal–insulator–metal (MIM) capacitor using Pr2O3 dielectrics

Metal–insulator–metal (MIM) capacitors with Pr₂O₃ as high-k material have been investigated for the first time. We varied the thickness of the Pr₂O₃ layers as well as the bottom electrode material. The layers are characterised using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), transmission electron microscopy (TEM) and secondary ion mass spectroscopy (SIMS). Preliminary information on the interaction of water with the films was obtained from XPS and ab initio pseudopotential calculations. The electrical characterisation shows that Pr₂O₃ MIM capacitors can provide higher capacitance densities than Si₃N₄ MIM capacitors while still maintaining comparable voltage coefficients of capacitance. The Pr₂O₃ dielectric material seems to be suitable for use in silicon RF applications.     

Epitaxy of BaTiO3 thin film on Si(0 0 1) using a SrTiO3 buffer layer for non-volatile memory application

In this study we report the epitaxial growth of BaTiO₃ films on Si(0 0 1) substrate buffered by 5 nm-thick SrTiO₃ layer using both MBE and PLD techniques. The BaTiO₃ films demonstrate single crystalline, (0 0 1)-oriented texture and atomically flat surface on SrTiO₃/Si template. The electrical characterizations of the BaTiO₃ films using MFIS structures show that samples grown by MBE with limited oxygen pressure during the growth exhibit typical dielectric behavior despite post deposition annealing process employed. A ferroelectric BaTiO₃ layer is obtained using PLD method, which permits much higher oxygen pressure. The C-V curve shows a memory window of 0.75 V which thus enable BaTiO₃ possibly being applied to the non-volatile memory application.     

具有界面依赖光致发光的双层WS2/Ga2O3异质结的能带工程(英文)

利用垂直WS₂/Ga₂O₃异质结构中异质界面诱导了反常的光致发光(PL)发射。垂直堆栈的WS₂/Ga₂O₃异质界面使其形成了II型能带结构,导致与Ga₂O₃层接触的底层WS₂的PL强度下降。而异质界面的强耦合作用也影响了双层WS₂中的同质层间相互作用,使得上层WS₂出现反常的PL增强。这种堆栈新型二维异质结构为定制目标能带结构并控制其光子和电子行为提供一种新的手段。     

氧化铟纳米管的制备及它的甲苯气敏特性研究

Abstract： The pristine In2O3 nanotubes were synthesized by electrospinning and subsequent calcination. Scanning electron microscope, X-ray powder diffraction and transmission electron micrograph were employed to analyze the morphology and crystal structure of the as-synthesized nanotubes. Gas-sensing properties of the as-synthesized In203 nanotubes were investigated by exposing the corresponding sensors to toluene, acetone, ethanol, formalde- hyde, ammonia and carbon monoxide at 340 ℃. The results show that the gas sensor possesses a good selectivity to toluene at 340 ℃. The response of the In2O3 nanotube gas sensor to 40 ppm is about 5.88. The response and recovery times are about 3 s and 17 s, respectively.     

New dielectric material system of Nd(Mg1/2Ti1/2)O3–CaTiO3 at microwave frequency

The microwave dielectric properties of (1 − x)CaTiO₃–xNd(Mg_1/2Ti_1/2)O₃ (0.1  x  1.0) ceramics prepared by the conventional solid state method have been investigated. The system forms a solid solution throughout the entire compositional range. The dielectric constant decreases from 152 to 27 as x varies from 0.1 to 1.0. In the (1 − x)CaTiO₃–xNd(Mg_1/2Ti_1/2)O₃ system, the microwave dielectric properties can be effectively controlled by varying the x value. At 1400 °C, 0.1CaTiO₃–0.9Nd(Mg_1/2Ti_1/2)O₃ has a dielectric constant (ε_r) of 42, a Q × f value of 35 000 GHz and a temperature coefficient of resonant frequency (τ_f) of −10 ppm/°C. As the content of Nd(Mg_1/2Ti_1/2)O₃ increases, the highest Q × f value of 43 000 GHz for x = 0.9 is achieved at the sintering temperature 1500 °C.     

Comparative study of AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors with Al2O3 and HfO2 gate oxide

AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors (MOSHFETs) with Al₂O₃ gate oxide which was deposited by atomic layer deposition (ALD) were fabricated and their performance was then compared with that of AlGaN/GaN MOSHFETs with HfO₂ gate oxide. The capacitance (C)-voltage (V) curve of the Al₂O₃/GaN MOS diodes showed a lower hysteresis and lower interface state density than the C-V curve of the HfO₂/GaN diodes, indicating better quality of the Al₂O₃/GaN interface. The saturation of drain current in the I_D-V_GS relation of the Al₂O₃ AlGaN/GaN MOSHFETs was not as pronounced as that of the HfO₂ AlGaN/GaN MOSHFETs. The gate leakage current of the Al₂O₃ MOSHFET was five to eight orders of magnitude smaller than that of the HfO₂ MOSHFETs.     

Atomic-layer-deposited Al2O3 and HfO2 on GaN: A comparative study on interfaces and electrical characteristics

Al₂O₃, HfO₂, and composite HfO₂/Al₂O₃ films were deposited on n-type GaN using atomic layer deposition (ALD). The interfacial layer of GaON and HfON was observed between HfO₂ and GaN, whereas the absence of an interfacial layer at Al₂O₃/GaN was confirmed using X-ray photoelectron spectroscopy and transmission electron microscopy. The dielectric constants of Al₂O₃, HfO₂, and composite HfO₂/Al₂O₃ calculated from the C-V measurement are 9, 16.5, and 13.8, respectively. The Al₂O₃ employed as a template in the composite structure has suppressed the interfacial layer formation during the subsequent ALD-HfO₂ and effectively reduced the gate leakage current. While the dielectric constant of the composite HfO₂/Al₂O₃ film is lower than that of HfO₂, the composite structure provides sharp oxide/GaN interface without interfacial layer, leading to better electrical properties.     

Influence of temperature on the etching rate of SiO2 in CF4 + O2 plasma

The plasmochemical etching of SiO₂ in CF₄ + O₂ plasma is considered. During the experiment SiO₂ films are etched in CF₄ + O₂ plasma at temperatures of 300 and 350 K. The dependences of plasmochemical etching rates of SiO₂ on O₂ content in the feed are measured. The experimental measurements are compared with theoretical calculations. The obtained theoretical results are used to predict the real dimensions of etched trenches. It is found that decrease in temperature reduces lateral undercutting due to decreased desorption of formed SiF₄ molecules from the sidewalls.     

插层Al2O3对氧化铪基忆阻器的性能优化及多值特性研究

近年来,氧化铪基忆阻器因其优异的阻变性能及与CMOS工艺兼容等特点而被广泛研究。然而,氧化铪基忆阻器仍存在以下问题:1) 器件良率、可靠性、均一性不足;2) Set和Reset 过程中电流突变,导致多值特性较差。为实现氧化铪基忆阻器的性能优化及多值特性,文章在HfO₂表面生长一层1~5 nm Al₂O₃,构造Al₂O₃/HfO₂双介质层忆阻器,并对HfO₂和Al₂O₃的厚度进行优化,最终得到性能显著提升的Al₂O₃/HfO₂双介质层多值忆阻器。该器件呈现出保持性良好的10个不同电阻态(1×10⁴ s@85℃)。由于氧离子在Al₂O₃层的迁移率更低,限制了氧空位细丝生长速率及宽度,且Al₂O₃具有热增强作用,使氧空位分布更均匀,促使氧空位细丝生成/断裂过程由突变转为渐变。该工作为进一步实现氧化铪基忆阻器的性能优化及多值特性提供了参考。     

电子束辐照下的石墨烯上的原子层沉积Al2O3介质层

为了研究石墨烯与高k介质的结合,使用原子层沉积氧化铝在石墨衬底上。沉积前使用电子束辐照,观测到了氧化铝明显改善的形貌。归因于电子束辐照过程中的石墨层的无定形变化过程。