The electrical characteristics of 4H-SiC schottky diodes after inductively coupled plasma etching

The electrical characteristics of metal contacts fabricated on 4H-SiC have been investigated. Sputtered nickel ohmic contacts have been successfully produced on untreated 4H-SiC substrates and 4H-SiC surfaces cleaned with aggressive chemicals and ion sputtering. The current-voltage (I–V) characteristics of asdeposited contacts are observed to be nonohmic on all surfaces. After annealing at 1,000°C in a N₂ atmosphere, the contacts are seen to become ohmic with considerably less annealing time being required for the samples exposed to aggressive cleaning stages. Schottky diodes were then produced on the silicon carbide (SiC) surface after etching in an SF₆/O₂ inductively coupled plasma (ICP) for 3 min at varying substrate bias voltages and also on an untreated surface used as a control sample. The ideality factors of all diodes formed on the etched surfaces increased in comparison to the control sample. The highest ideality factor was observed for the diodes produced after etching at −0-V and −245-V bias voltage. A two-diode and resistor model was applied to the results that successfully accounted for the excess leakage paths. The defect density of each SiC surface was calculated using both the measured and the simulated ideality factors. An annealing stage was successful at reducing the ideality factors of all the diodes formed. The defect density calculated using the measured ideality factors of the annealed diodes was seen to have been reduced by an order of magnitude.     

Elevated temperature nitrogen implants in 6H-SiC

Elevated temperature (700°C) N ion implantations were performed into 6H-SiC in the energy range of 50 keV-4 MeV. By analyzing the as-implanted depth distributions, the range statistics of the N⁺ in 6H-SiC have been established over this energy range. Annealing at 1500 and 1600°C for 15 min resulted in Rutherford backscattering spectrometry scattering yields at the virgin crystal level, indicating a good recovery of the crystalline quality of the material without any redistribution of the dopant. A maximum electron concentration of 2 × 10¹⁹ cm⁻³, at room temperature, has been measured even for high-dose implants. The p-n junction diodes made by N ion implantation into a p-type substrate have a forward turn-on voltage of 2.2 V, an ideality factor of 1.90, and a reverse breakdown voltage of 125 V with nA range leakage current for -10 V bias at room temperature. By probing many devices on the same substrate we found uniform forward and reverse characteristics across the crystal.     

Microwave Annealing of High Dose Al<Superscript>+</Superscript>-implanted 4H-SiC: Towards Device Fabrication

High-purity semi-insulating 8° off-axis 〈0001〉 4H-SiC was implanted with Al⁺ at different doses and energies to obtain a dopant concentration in the range of 5 × 10¹⁹–5 × 10²⁰ cm^?3. A custom-made microwave heating system was employed for post-implantation annealing at 2,000 °C for 30 s. Sheet resistance and Hall-effect measurements were performed in the temperature range of 150–700 K. At room temperature, for the highest Al concentration, a minimum resistivity of 3 × 10^?2 Ω cm was obtained, whereas for the lowest Al concentration, the measured resistivity value was 4 × 10^?1 Ω cm. The onset of impurity band conduction was observed at around room temperature for the samples implanted with Al concentrations ≥3 × 10²⁰ cm^?3. Vertical p ⁺-i-n diodes whose anodes were made by 1.5 × 10²⁰ cm^?3 Al⁺ implantation and 2,000 °C/30 s microwave annealing showed exponential forward current–voltage characteristics with two different ideality factors under low current injection. A crossover point of the temperature coefficient of the diode resistance, from negative to positive values, was observed when the forward current entered the ohmic regime.     

Effects of annealing treatment on the high temperature performance of 4H-SiC metal-semiconductor-metal ultraviolet photodiodes

The high temperature performance plays a crucial role in the high-temperature harsh environment detection. In this paper, the electrical and optical characteristics of 4H-SiC metal-semiconductor-metal (MSM) ultraviolet photodiodes (PDs) were investigated at high temperatures. The C-V measurement indicates that the 4H-SiC Schottky barrier diode is partially depleted at 40 V bias. Analysis of I-V data based on the thermionic emission theory demonstrates that the annealing treatment at 400 °C can effectively improve the homogeneity of Ni/4H-SiC Schottky barrier height. Experimental results confirm that the annealing treatment is beneficial not only to reduce the dark current and improve the photoresponse, but also to enhance the sensitivity for 4H-SiC MSM PDs. The sensitivity of 400 °C annealed MSM PDs (6.2 × 10³) is five times larger than that of as-deposited MSM PDs (1.3 × 10³) at 200 °C.     

Interface state density in Au-nGaAs Schottky diodes

A method for determining the surface state density in Schottky diodes taking into account both I–V and C–V data while considering the presence of a deep donor level is presented. The model assumes that the barrier height is controlled by the energy distribution of surface states in equilibrium with the metal and the applied potential and does not include, explicitly, an interfacial layer. The model was applied to extract interface state densities of Au-nGaAs guarded Schottky diodes fabricated from bulk and VPE (100) GaAs with carrier conentrations between 3 × 10¹⁵ and 8 × 10¹⁶ cm^?3. These diodes exhibited ideality (n) factors of approximately 1.02 and room temperature saturation current densities ～10^?8 A/cm². This model is in substantial agreement with forward bias measurements over the 77–360°K temperature range investigated, in that a temperature-independent energy distribution of interface states was obtained. In reverse bias the interface state model is most valid with the higher carrier concentration material and at high temperature and low bias voltage. Typical interface state densities from 0.07 eV above the zero bias Fermi level to 0.01 eV below the Fermi level were 2 × 10¹³ cm^?2 eV^?1. The validity of the model under reverse bias is restricted by a non-thermionic reverse current, thought to be enhance field emission from traps.     

Effect of Annealing Ambient on the Electrical and Optical Properties of Aluminum-Doped ZnO Films Produced via a Sol–Gel Process

In this study, aluminum-doped ZnO (AZO) thin films were prepared by a sol–gel with spin coating process. The AZO films were annealed by a two-step process. The films were first annealed in air or nitrogen at 500°C for 3 h, followed by annealing in three types of ambient, i.e., vacuum (10^?3 Torr or 10^?6 Torr) or forming gas (10% H₂/90% N₂), at 500°C for 4 h. The effect of the annealing ambient on the microstructure, electrical and optical properties of the AZO films was explored by x-ray diffraction, field-emission scanning electron microscopy, four-point probe sheet resistivity measurements, Hall voltage measurements, and ultraviolet–visible spectroscopy. The results showed that the size of AZO particulates in the films was determined mainly by the first annealing step. The films annealed in air in the first step were composed of larger AZO particulates than those annealed in nitrogen. The conductivities of the AZO films were significantly increased by the second annealing step. Second annealing in a high-vacuum system (10^?6 Torr) led to the highest AZO film conductivity among the three ambients. Regardless of the various annealing processes, the films remained transparent under visible light and exhibited a sharp absorption edge in the ultraviolet region. The highest conductivity, i.e., 168 S cm^?1, was obtained from films annealed first in air and then in vacuum of 10^?6 Torr.     

Modification of the dark and photoconductivity and the optical transmittance of solution-grown CdS thin films

Very interesting behaviour is shown by chemically deposited CdS thin films for optoelectronic applications after air and vacuum (10^?5 Torr) annealing. Vacuum annealing of samples at about 100°C caused the dark conductivity to improve by five orders of magnitude. The dark and photoconductivity of air-annealed (at around 200°C) samples increased by seven and two orders of magnitude respectively. Air-annealed (at 350°C for about 2 min) samples exhibited a very quick photoresponse (<2 s for two decades of photocurrent decay) with σ_p/σ_d ≈ 10⁵ for a bias of 10 V, which may be exploited for photodetector applications. Air or vacuum annealing of samples for a minimum of 10–15 min caused the optical transmittance above the band edge to increase by 10%–15% and annealing the sample at 200°C caused the absorption edge to shift towards the longer-wavelength region compared with the as-prepared and 100 and 350°C annealed films.     

Ni，Ti/4H-SiC肖特基势垒二极管

采用本实验室生长的4H-SiC外延片,分别用高真空电子束蒸Ni和Ti做肖特基接触金属,Ni合金作欧姆接触,SiO_2绝缘环隔离减小高压电场集边效应等技术,制作出4H-SiC肖特基势垒二极管(SBD)。该器件在室温下反向击穿电压大于600 V,对应的漏电流为2.00×10~(-6)A。对实验结果分析显示,采用Ni和Ti作肖特基势垒的器件的理想因子分别为1.18和1.52,肖特基势垒高度为1.54 eV和1.00 eV。实验表明,该器件具有较好的正向整流特性。     

Effect of the annealing temperature on erbium ion electroluminescence in Si:(Er,O) diodes with (111) substrate orientation

The influence of the temperature of secondary annealing, stimulating the formation of optically and electrically active centers, on the erbium ion electroluminescence (EL) at λ≈1.54 μm in (111) Si:(Er,O) diodes has been studied. The diodes were fabricated by the implantation of 2.0 and 1.6 MeV erbium ions at doses of 3×10¹⁴ cm⁻² and oxygen ions (0.28 and 0.22 MeV, 3×10¹⁵ cm⁻²). At room temperature, the EL intensity in the breakdown mode grows with the annealing temperature increasing from 700 to 950°C. At annealing temperatures of 975–1100°C, no erbium EL is observed in the breakdown mode owing to the formation of microplasmas. The intensity of the injection EL at 80 K decreases with the annealing temperature increasing from 700 to 1100°C. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 35, No. 10, 2001, pp. 1224–1227. Original Russian Text Copyright ? 2001 by Sobolev, Emel’yanov, Nikolaev.     

Al+ and B+ implantations into 6H-SiC epilayers and application to pn junction diodes

Aluminum (Al) and boron (B) ion implantations at room temperature into n-type 6H-SiC epilayers have been investigated. Rutherford backscattering spectroscopy (RBS) channeling measurements revealed larger lattice damage in Al⁺ implantation at a given total implantation dose. A nearly perfect electrical activation ratio (>90%) could be attained by high-temperature annealing at 1600°C for Al⁺ and 1700°C for B⁺ implantations. Mesa pn junction diodes formed by either Al⁺ or B⁺ implantation with a 1×10¹⁴ cm⁻² dose exhibited high blocking voltages of 950∼1070 V, which are 80∼90% of the ideal value predicted for the diode structure. The forward current can clearly be divided into two components of diffusion and recombination currents. B⁺-implanted diodes showed higher breakdown voltage on average but poor forward conduction. Comparison of the performance of Al⁺ and B⁺-implanted diodes is discussed.     

Investigation of structural and optoelectronic properties of annealed nickel phthalocyanine thin films

Thin films of nickel phthalocyanine (NiPc) were prepared by thermal evaporation and the effects of annealing temperature on the structural and optical properties of the samples were studied using different analytical methods. Structural analysis showed that the grain size and crystallinity of NiPc films improved as annealing temperature increased from 25 to 150 °C. Also, maximum grain size (71.3 nm) was obtained at 150 °C annealing temperature. In addition, NiPc films annealed at 150 °C had a very smooth surface with an RMS roughness of 0.41 nm. Optical analysis indicated that band gap energy of films at different annealing temperatures varied in the range of 3.22–3.28 eV. Schottky diode solar cells with a structure of ITO/PEDOT:PSS/NiPc/Al were fabricated. Measurement of the dark current density–voltage (J–V) characteristics of diodes showed that the current density of films annealed at 150 °C for a given bias was greater than that of other films. Furthermore, the films revealed the highest rectification ratio (23.1) and lowest barrier height (0.84 eV) demonstrating, respectively, 23% and 11% increase compared with those of the deposited NiPc films. Meanwhile, photoconversion behavior of films annealed at 150 °C under illumination showed the highest short circuit current density (0.070 mA/cm²) and open circuit voltage of (0.55 V).     

Effect of annealing temperature on the electrical characteristics of Platinum/4H-SiC Schottky barrier diodes

Pt/4H-SiC Schottky barrier diodes have been fabricated to investigate the effect of annealing on the electrical characteristics of the fabricated devices. The parameters such as barrier height, ideality factor and donor concentration were deduced from the current–voltage (I–V) and the capacitance–voltage (C–V) measurements at room temperature. Diodes showed non-ideal behaviour like high value of ideality factor and lower value of barrier height. A barrier height of 1.82?eV was obtained from C–V measurements and it was 1.07?eV when obtained from the I–V measurements with ideality factor 1.71 for as-deposited diodes at room temperature. The diodes, therefore, were annealed in the temperature range from 25°C to 400°C to observe the effect of annealing temperature on these parameters. Schottky barrier height and ideality factors were found to be temperature-dependent. After rapid thermal annealing upto 400°C, a barrier height of 1.59?eV from C–V measurements and the value of 1.40?eV from I–V measurements with ideality factor 1.12 were obtained. Barrier heights deduced from C–V measurements were consistently larger than those obtained from I–V measurements. To come to terms with this discrepancy, we re-examined our results by including the effect of ideality factor in the expression of the barrier height. This inclusion of ideality factor results in reasonably good agreement between the values of barrier height deduced by the above two methods. We believe that these improvements in the electrical parameters result from the improvement in the quality of interfacial layer.     

Fabrication and characterization of 4H-SiC P-N junction diodes by selective-epitaxial growth using TaC as the mask

Selective nitrogen doping of 4H-SiC by epitaxial growth using TaC as the high-temperature mask has been demonstrated. Nomarski optical microscopy and scanning electron microscopy (SEM) were used to characterize selective growth of SiC. In addition, 250-μm, square-shaped, p-n junction diodes by selective n-type epitaxial growth on a p-type epilayer were fabricated. The refilled fingers with different width were designed to vary the periphery/area (P/A) ratio. The effects of P/A ratio on the current-voltage (J-V) characteristics have been investigated. The ideality factor extracted from J-V characteristics is ≈2 at a temperature range of 25–275°C, which indicates that the Shockley-Read-Hall recombination is the dominant mechanism in the conduction region. The reverse leakage current does not show dependence on P/A ratio for trench-refilled diodes. The room-temperature reverse leakage-current density at 100 V is less than 3.5×10⁻⁷ A/cm² for all diodes. Also, the reverse leakage current does not increase significantly with temperature up to 275°C. The breakdown voltages measured at room temperature are about 450 V and 400 V for diodes without and with fingers, respectively.     

Effect of annealing temperature on 1.5 μm photoluminescence from Er-lmplanted 6H-SiC

The effect of post-implantation anneal on erbium-doped 6H-SiC has been investigated. 6H-SiC has been implanted with 330 keV Er⁺ at a dose of 1 × 1013 /cm2. Er depth profiles were obtained by secondary ion mass spectrometry (SIMS). The as-implanted Er-profile had a peak concentration of∼1.3 × 10¹⁸/cm³ at a depth of 770Å. The samples were annealed in Ar at temperatures from 1200 to 1900°C. The photoluminescence intensity integrated over the 1.5 to 1.6 μm region is essentially independent of annealing temperature from 1400 to 1900°C. Reduced, but still significant PL intensity, was measured from the sample annealed at 1200°C. The approximate diffusivity of Er in 6H SiC was calculated from the SIMS profiles, yielding values from 4.5 × 10⁻¹⁶ cm²/s at 1200°C to 5.5 × 10⁻¹⁵ cm²/s at 1900°C.     

Improved Ni Schottky Contacts on <Emphasis Type="Italic">n</Emphasis>-Type 4H-SiC Using Thermal Processing

High-temperature processing was used to improve the barrier properties of three sets of n-type 4H-SiC Schottky diodes fabricated with Ni Schottky contacts. We obtained an optimum average barrier height of 1.78 eV and an ideality factor of 1.09 using current–voltage measurements on diodes annealed in vacuum at 500°C for 24 h. Nonannealed contacts had an average barrier height of 1.48 eV and an ideality factor of 1.85. The Rutherford backscattering spectra of the Ni/SiC contacts revealed the formation of a nickel silicide at the interface, accompanied by a substantial reduction in oxygen following annealing.     

Alloyed tin-gold ohmic contacts to n-type indium phosphide

The formation of alloyd ohmic contacts on n-InP using sequentially deposited Sn plus Au films was investigated. The specific contact resistance for metallizations with a Sn content of 5 at. % was determined for annealing temperatures between 250 and 500°C. The minimum specific contact resistance, r_c = (1.8±0.9) × 10^?6 ohm-cm² occurred for a narrow range of annealing temperatures between 380 and 410°C on substrates with n = 3 × 10¹⁸/cm³. For annealing temperatures 350°C the contacts were non-Ohmic and above 420°C the resistance increased dramatically. Contact morphology and metallurgy were studied by optical and scanning electron microscopy, X-ray diffraction, Auger electron spectroscopy and Rutherford backscattering. Films annealed above 320°C contained several phases, mainly Au₄In, AuSn and polycrystalline InP. The contacts annealed at temperatures above 410°C were composed predominantly of the single phase Au₃In₂.     

Electrical Characteristics of Ti/Al Ohmic Contacts to Molecular Beam Epitaxy-Grown N-polar n-type GaN for Vertical-Structure Light-Emitting Diodes

We investigated the electrical properties of Ti(30?nm)/Al(200?nm) contacts to molecular beam epitaxy-grown N-polar n-GaN with different carrier concentrations. Samples with carrier concentration of 1.2?×?10¹⁸?cm^?3 showed nonohmic behaviors when annealed at 300°C, but ohmic at 500°C and 700°C. All samples with carrier concentration of 2.0?×?10¹⁹?cm^?3 exhibited ohmic behavior. x-Ray photoemission spectroscopy (XPS) results showed that, for samples with carrier concentration of 1.2?×?10¹⁸?cm^?3, the Ga 2p core levels shift to lower or higher binding energy upon annealing at 300°C or above 500°C, respectively. Scanning transmission electron microscopy (STEM) results showed that, for samples with carrier concentration of 1.2?×?10¹⁸?cm^?3, a wurtzite AlN layer (??2?nm thick) formed at the metal/GaN interface when the samples were annealed at 500°C. An interfacial wurtzite AlN layer also formed upon annealing at 700°C, but its thickness was ??4?nm. Based on the XPS and STEM results, the ohmic contact formation and degradation mechanisms are described and discussed.     

Heterojunction diodes in 3C-SiC/Si system grown by reactive magnetron sputtering: Effects of growth temperature on diode rectification and breakdown

3C-SiC/Si heterojunction diodes were prepared by reactive magnetron sputtering of pure Si in CH₄-Ar discharge on Si(111) substrates kept at temperatures (T_s) ranging from 800 to 1000°C. A good diode rectification process started for films grown at T_s≤900°C. Heterojunction diodes grown at T_s = 850°C showed the best performance with a saturation current density of 2.4 × 10⁻⁴ A cm⁻². Diode reverse breakdown was obtained at a voltage of −110 V. The doping concentration (N_d) of the 3C-SiC films was calculated from 1/C² vs V plot to be 3 × 10¹⁵ cm⁻³. Band offset values obtained were −0.27 and 1.35 eV for the conduction and valence band, respectively. X-ray diffraction analysis revealed the film grown at T_s = 850°C to be single-phase 3C-SiC. The full width at half maximum of the 3C-SiC(111) peak was only 0.25 degree. Cross-sectional transmission electron microscopy showed the film to be highly (111)-oriented with an epitaxial columnar structure of double positioning domain boundaries.     

Low-resistance Ti/Al ohmic contact on undoped ZnO

We report a low-resistance ohmic contact on undoped ZnO using a promising contact scheme of Ti/Al. Specific-contact resistivity, as low as 9.0 × 10^?7 ωcm², was obtained from the Ti (300 Å)/Al (3,000 Å) contact annealed at 300°C. It was found that TiO was produced, and the atomic ratio of Zn/O was dramatically increased after annealing at 300°C. This provides the evidence that a number of oxygen vacancies, acting as donors for electrons, were produced below the contact. This leads to the increase of electron concentration via the reduction of contact resistivity.     

Fabrication approaches to ZnO nanowire devices

To date, most of the work on ZnO nanostructures has focused on the synthesis methods and there have been only a few reports of the electrical characteristics. We report on fabrication methods for obtaining device functionality from single ZnO nanorods. A key aspect is the use of sonication to facilitate transfer of the nanorods from the initial substrate on which they are grown to another substrate for device fabrication. Examples of devices fabricated using this method are briefly described, including metal-oxide semiconductor field effect depletion-mode transistors with good saturation behavior, a threshold voltage of ∼−3 V, and a maximum transconductance of order 0.3 mS/mm and Pt Schottky diodes with excellent ideality factors of 1.1 at 25°C and very low (1.5×10⁻¹⁰ A, equivalent to 2.35 Acm⁻², at −10 V) reverse currents. The photoresponse showed only a minor component with long decay times (tens of seconds) thought to originate from surface states. These results show the ability to manipulate the electron transport in nanoscale ZnO devices.