Blends of poly(2,6-dimethyl-1,4-phenylene oxide)/ poly(styrene-co-methacrylic acid)/ poly(ethyl methacrylate-co-4-vinylpyridine)

Summary The miscibility of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) with poly(styrene-co-acrylic acid) (SAA) or poly(styrene-co-methacrylic acid) (SMA) containing respectively up to 22 mol % of acrylic or methacrylic acid was studied by Differential Scanning Calorimetry and viscosimetry. All PPO/SAA or PPO/SMA blends containing 60% or less by weight of PPO were miscible and showed only one glass transition temperature (Tg). Above 60% of PPO, two Tg's were however observed for the blends in which the acid content in the SAA or SMA reaches 20% or 12% by mole respectively; the higher Tg is slightly lower than the one of pure PPO, while the lower one corresponds to a miscible blend of lower content of PPO.A DSC study showed that depending on the blend ratio, two or three glass transition temperatures were observed when a copolymer of ethyl methacrylate containing 8 mol % of 4-vinylpyridine (EM4VP-8) was added to miscible PPO/SMA-12 blends. The PPO dissolution in the SMA-12 copolymer was affected by the specific interactions that occurred between this latter copolymer and the EM4VP-8.     

通过状态方程预测无定形和可结晶共混聚合物的压力-体积-温度和超摩尔体积（英文）

In this work the statistical mechanical equation of state was developed for volumetric properties of crystal ine and amorphous polymer blends. The Ihm–Song–Mason equations of state (ISMEOS) based on temperature and density at melting point (Tm andρm) as scaling constants were developed for crystalline polymers such as poly(propylene glycol)+poly(ethylene glycol)-200 (PPG+PEG-200), poly(ethylene glycol) methyl ether-300 (PEGME-350)+PEG-200 and PEGME-350+PEG-600. Furthermore, for amorphous polymer blends con-taining poly(2,6-dimethyl-1,4-phenylene oxide) (PPO)+polystyrene (PS) and PS+poly(vinylmethylether) (PVME), the density and surface tension at glass transition (ρg andγg) were used for estimation of second Virial coefficient. The calculation of second Virial coefficients (B2), effective van der Waals co-volume (b) and correction factor (α) was required for judgment about applicability of this model. The obtained results by ISMEOS for crys-talline and amorphous polymer blends were in good agreement with the experimental data with absolute aver-age deviations of 0.84%and 1.04%, respectively.     

Glass transitions of poly(bisphenol-A carbonate)/ultraviolet light stabilizer blends by DSC and TOA

Glass transition temperatures are reported for poly(bisphenol-A-carbonate) plasticized by 0–12 wt % of the ultraviolet light stabilizers 2-hydroxy-4-methoxy-benzophenone, 2-hydroxy-4-n-octooxy-benzophenone, and 2-hydroxy-4-dodecyloxy-benzophenone. Differential scanning calorimetry (DSC) and thermooptical analysis (TOA) were employed. The glass transition temperatures increased somewhat with shelf time for the room temperature air-dried 1-mil films drawn from methylene chloride solutions. A Bierbaum scratch hardness of 8.8 kg·mm^?2 was observed for a 10-mil poly(bisphenol-A carbonate) film. The effect of load applied to the diamond point (Bierbaum scratch technique) on the shape of TOA transmitted light intensity vs. temperature curves for the resultant scratches was examined. Although the curve shapes are greatly affected, the characteristic TOA temperatures derived therefrom remain essentially unchanged. The glass transition regions are not quite as broad for these polymer/plasticizer blends as they are for compatible polymer/polymer blends. T_TOA, the temperature at which birefringence disappears in the scratched films, is found identical to T_f (DSC), the temperature at which the specific heat transition is completed.     

Atactic poly(methyl methacrylate) blended with poly(3‐D(−)hydroxybutyrate): Miscibility and mechanical properties

Atactic poly(methylmethacrylate), aPMMA, was blended with poly(3‐D(−)hydroxybutyrate), PHB, up to a maximum composition of 25% of polyester, at 190°C in a Brabender‐like apparatus. The resulting blends quenched from the melt to room temperature were completely amorphous, and exhibited a single glass transition using DSC and DMTA, indicating miscibility of the components for this time–temperature history. Tensile experiments showed that at room temperature the 10/90 and 20/80 PHB/aPMMA blends exhibited higher values of strain at break, and slight decreases of the modulus and stress at break compared to neat aPMMA. The tensile energy at break was almost twice that of neat aPMMA. Tensile tests were also performed at 80°C, at which point the 25/75 and 20/80 PHB/aPMMA blends are above T_g, while the 10/90 and neat aPMMA are below T_g. The stress–strain curves obtained were functions of the physical state of the amorphous phase, and also depended on the difference between the test temperatures and T_g. In particular, comparing the neat aPMMA and the blends, decreases of the modulus and stress at break and a respectable increase in the strain at break were observed in the latter. Finally, the results were commented considering the thermal degradation of PHB in the melt during the blend preparation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 746–753, 2000     

Polymer nanocomposites containing carbon nanotubes and miscible polymer blends based on poly[ethylene‐co‐(acrylic acid)]

Four binary polymer blends containing poly [ethylene‐co‐(acrylic acid)] (PEAA) as one component, and poly(4‐vinyl phenol‐co‐2‐hydroxy ethyl methacrylate) (P4VPh‐co‐2HEMA) or poly(2‐ethyl‐2‐oxazoline) (PEOx) or poly(vinyl acetate‐co‐vinyl alcohol) (PVAc‐co‐VA) or poly (vinylpyrrolidone‐co‐vinyl acetate) (PVP‐co‐VAc) as the other component were prepared and used as a matrix of a series of composite materials. These binary mixtures were either partially or completely miscible within the composition range studied and were characterized by differential scanning calorimetry (DSC) and Fourier transformed infrared spectroscopy (FTIR). Carbon nanotubes (CNTs) were prepared by a thermal treatment of polyester synthesized through the chemical reaction between ethylene glycol and citric acid over an alumina boat. High resolution transmission electron microscopy (HRTEM) was used to characterize the synthesized CNTs. Films of composite materials containing CNTs were obtained after evaporation of the solvent used to prepare solutions of the four types of binary polymer blends. Young's moduli of the composites were obtained by thermomechanical analysis at room temperature. Only one glass transition temperature was detected for several compositions on both binary blends and the composite material matrices. Evidence of hydrogen bond formation was recorded for both miscible blends and composite materials. The degree of crystallinity and Young's moduli of the CNT‐polymer composites increased compared to the single polymer blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Hydrophilicity,crystallinity and electrostatic dissipating properties of poly(oxyethylene)-segmented polyurethanes

Plaques of poly(oxyethylene)-segmented polyurethanes prepared from isophorone diisocyanate (IPDI) and polyethylene glycol (PEG) were used to probe the structure/property relationships with regard to hydrophilicity, crystallinity and electrostatic dissipating (ESD) ability. The prepared urethane polymers or oligomers consistently exhibited lower surface resistivities than their corresponding PEG-1000, 2000 and 8000 starting materials. The magnitude of the decrease in surface resistivity (ohm/sq) was correlated with heat of crystallinity, measured by differential scanning calorimetry. Surface resistivity as low as 10^7.5 ohm/sq for PEG-1000/IPDI polyurethane, a decrease by 2.5 orders of magnitude from pure PEG-1000, was observed and attributed to the differences in crystallinity. Polyurethanes containing PEG, polypropylene glycol (PPG) and mixed PEG/PPG were also prepared for comparison. The mixed PEG/MDEA (N -methyl diethanolamine) polyurethanes further demonstrated the importance of the nature and mobility of the hydrophilic groups for lowering the polymer surface resistivity. To account for these observations, an electron conducting mechanism via association and mobility of the hydrogen-bonded water molecules with hydrophilic poly(oxyethylene) groups is suggested. © 1999 Society of Chemical Industry     

Thermal characteristics of IPNs composed of poly(propylene glycol) and poly(acrylic acid)

Interpenetrating polymer networks (IPNs) based on poly(propylene glycol) (PPG) and poly(acrylic acid) (PAAc) were prepared by UV irradiation and characterized using fourier transform infrared (FTIR), differential scanning calorimetry (DSC), dielectric analysis (DEA), and thermogaravimetry (TGA). The glass transition temperatures (T_gs) of these IPNs exhibited a relatively higher temperature with an increased PAAc content. The decomposition temperature of PAAc is lower than that of PPG. PAAc affects the thermal stability of IPN more than PPG. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2570–2574, 2003     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with high molecular weight poly(lactic acid) blends determined by thermal analysis

An important strategy used in the polymer industry in recent years is blending two bio‐based polymers to attain desirable properties similar to traditional thermoplastics, thus increasing the application potential for bio‐based and bio‐degradable polymers. Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) with poly(L ‐lactic acid) (PLA) were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Three different grades of commercially available PLAs and one type of PHBV were blended in different ratios of 50/50, 60/40, 70/30, and 80/20 (PHBV/PLA) using a micro‐compounder at 175°C. The DSC and TGA analysis showed the blends were immiscible due to different stereo configuration of PLA polymer and two distinct melting temperatures. However, some compatibility between PHBV and PLA polymers was observed due to decreases in PLA's glass transition temperatures. Additionally, the blends do not show clear separation by SEM analysis, as observed in the thermal analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Novel ionomers based on blends of ethylene-acrylic acid copolymers with poly(vinyl amine)

The polymerization of N-vinyl formamide followed by hydrolysis yields a linear, water-soluble poly(vinyl amine). The high concentration of pendant primary amine groups leads to a polymer with an interesting set of properties. Complexation with water-soluble anionic polyelectrolytes in water solutions leads to a highly water-insoluble material. The study described herein investigated the phase behavior/properties of melt blends of poly(vinyl amine) with ethylene-acrylic acid (EAA) copolymers of less than 10 wt % acrylic acid. The calorimetric and dynamic mechanical analyses of the resultant blends show that the vinyl amine groups are accessible to the acrylic acid groups of the copolymers and the major property changes occur up to the stoichiometric addition of vinyl amine/acrylic acid. At higher levels of vinyl amine (vinyl amine/acrylic acid mol ratio > 4), additional poly(vinyl amine) forms a separate phase. The mechanical, dynamic mechanical, and calorimetric properties of these blends below the stoichiometric ratio show analogous trends as with typical alkali/alkaline metal neutralization. These characteristics relative to the base EAA include improved transparency, lower melting and crystallization temperature, lower level of crystallinity, and increased modulus and strength. The emergence of the β transition in dynamic mechanical testing is pronounced with these blends (as with alkali/alkaline metal neutralization), indicative of microphase separation of the amorphous phase into ionic-rich and ionic-depleted regions. A rubbery modulus plateau for the blends exists above the polyethylene melting point, demonstrating ionic crosslinking. Above 150°C exposure, further modulus increases occur presumably due to amide formation. This study demonstrates that the highly polar poly(vinyl amine) can interact with acrylic acid units in an EAA copolymer comprised predominately of polyethylene (>90 wt %). The thermodynamic driving force favoring ionic association overrides the highly unfavorable difference in composition. © 1996 John Wiley & Sons, Inc.     

Compatibilizing effects of poly(styrene-graft-ethylene oxide) in blends of polystyrene and butyl acrylate polymers

The compatibilizing effect of poly(styrene-graft-ethylene oxide) in polystyrene (PS) blends with poly(n-butyl acrylate) (PBA) and poly(n-butyl acrylate-co-acrylic acid) (PBAAA) was investigated. No significant effects of the graft copolymer on the domain size were found in the PBA blends. By functionalizing PBA with acrylic acid, the average size of the polyacrylate domains was reduced considerably by the graft copolymer. Thermal and dynamic mechanical analysis of the PS/PBAAA blends revealed that the PBAAA glass transition temperature (T_g) decreased with increasing graft copolymer content. The effect of the graft copolymer in the PS/PBAAA blends can be explained by interactions across the interface due to the formation of hydrogen bonds between the poly(ethylene oxide) (PEO) side chains in the graft copolymer and the acrylic acid segments in the PBAAA phase. Hydrogen bonding was confirmed by IR analysis of binary blends of PEO and PBAAA. Partial miscibility in the PEO/PBAAA blends was indicated by a PEO melting point depression and by a T_g reduction of the PBAAA phase. The thermal properties of the PEO/PBA blends indicated only very limited miscibility. © 1996 John Wiley & Sons, Inc.     

Calorimetric and dielectric study on poly(trimethylene terephthalate)/polycarbonate blends

Poly(trimethylene terephthalate) (PTT)/polycarbonate (PC) blends with different compositions were prepared by melt blending. The miscibility and phase behavior of melt-quenched and cold-crystallized blends were studied using differential scanning calorimetry (DSC) and dielectric relaxation spectroscopy. The blends of all compositions display only one glass transition (T _g ) in both states. The melting temperature and the crystallinity of PTT in the blend decrease with increasing PC content. The dielectric results for the melt-quenched blends, for PC content up to 60 wt.%, exhibited two merged relaxation peaks during the heating scan; the lower temperature relaxation peak represent the normal glass-transition (α) relaxation of the mixed amorphous phase and the higher temperature relaxation due to the new-constrained mixed amorphous phase after crystallization. Cold-crystallized blends displayed only one glass transition α-relaxation whose temperatures varied with composition in manner similar to that observed by DSC. The dielectric α-relaxation of cold crystallized blends has been analyzed. Parameters relating to relaxation broadening, dielectric relaxation strength, and activation energy were quantified and were found to be composition dependent. The PTT/PC blends could be considered as two-phase system, a crystalline PTT phase and a mixed amorphous phase consisting of a miscible mixture of the two polymers. However, the crystallinity was only detected for blends containing greater than 40 wt.% PTT.     

Miscibility of poly(vinylidene fluoride) and potassium salt of poly(methyl methacrylate-ran-methacrylic acid)

The crystalline–amorphous polymer pair of poly(vinylidene fluoride) and poly(methyl methacrylate) is known to be miscible over a wide composition range. The effects of ionic moieties on the miscibility were studied by replacing the poly(methyl methacrylate) with a series of random copolymers of methyl methacrylate and potassium salt of methacrylic acid. The interaction parameter (χ) for the miscible blends in their molten state was obtained by thermal analysis using a melting-point depression calculation. The parameter decreased to a minimum at c.2% ion content (χ=minus;0.514) and approached a positive value at above 10% ion concentration.     

Study of miscibility of poly(vinyl acetate) and poly(vinyl alcohol) blends by fluorescence spectroscopy

Secondary relaxation of poly(vinyl alcohol) (PVA), poly(vinyl acetate) (PVAc), and their blends in different proportions (9 : 1, 1 : 1, and 1 : 9) were studied by photoluminescence of anthracene, fluorescein, and both probes dissolved in the polymer blends. The temperature of the glass transition in the homopolymers was determined by the radiationless deactivation of anthracene as T_g(PVAc) ? 304 K and the photobleaching of fluorescein as T_g(PVA) ? 350 K. The relaxation processes of the different phases of the polymer blends occur at temperatures close to the homopolymers, which may be explained by the localization of each molecular probe within the matrix. These deactivation curves, however, are not similar to those of the individual homopolymers, suggesting a partial miscibility between these polymers. © 1995 John Wiley & Sons, Inc.     

Effect of drying conditions on the glass transition of poly(acrylic acid)

Systematic changes of drying conditions of poly(acrylic acid) were tested to study their effect on the glass transition of the material. The materials were synthesized in two different mediums of water and benzene, respectively. The glass transition temperatures of the samples were determined by thermal analysis using DSC. The samples were also characterized by IR spectra. The glass transition of poly(acrylic acid) was found to be significantly dependent on the drying conditions and also dependent on the medium in which poly(acrylic acid) was prepared. The anhydride formation in poly(acrylic acid) was increased as the drying temperature was raised, resulting in the increase of the glass transition temperature. The “bound” water involved in the preparation of poly(acrylic acid) in water medium could affect significantly the glass transition of the sample. A significant discrepancy in the previously reported values of the glass transition temperature of poly(acrylic acid) seems to be due to the differences in the drying conditions of the materials.     

Miscibility and melting behavior of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends

The miscibility and melting behavior of binary crystalline blends of poly(ethylene terephthalate) (PET)/poly(trimethylene terephthalate) (PTT) have been investigated with differential scanning calorimetry and scanning electron microscope. The blends exhibit a single composition‐dependent glass transition temperature (T_g) and the measured T_g fit well with the predicted T_g value by the Fox equation and Gordon‐Taylor equation. In addition to that, a single composition‐dependent cold crystallization temperature (T_cc) value can be observed and it decreases nearly linearly with the low T_g component, PTT, which can also be taken as a valid supportive evidence for miscibility. The SEM graphs showed complete homogeneity in the fractured surfaces of the quenched PET/PTT blends, which provided morphology evidence of a total miscibility of PET/PTT blend in amorphous state at all compositions. The polymer–polymer interaction parameter, χ₁₂, calculated from equilibrium melting temperature depression of the PET component was ?0.1634, revealing miscibility of PET/PTT blends in the melting state. The melting crystallization temperature (T_mc) of the blends decreased with an increase of the minor component and the 50/50 sample showed the lowest T_mc value, which is also related to its miscible nature in the melting state. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Compatibility of poly(ϵ-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) blends. I. Blends containing SAN with 24 wt% acrylonitrile

Polymer blends of poly(?-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN), containing 24 wt % acrylonitrile (AN), were prepared, and their transition behavior was examined by thermal analysis and dynamic mechanical testing. The blends were judged to be compatible on the basis of the presence of a single, compositionally dependent glass transition. The results of thermal treatment upon blends glass transition behavior and the dependence of thermal history upon the crystallization of semicrystalline PCL were also studied. The crystallization of PCL from SAN/PCL blends was found to be retarded by the presence of SAN, and crystalline PCL was found to exist only in blends containing a high PCL concentration. Blends which do not contain crystalline PCL were transparent, and their glass transition behavior can be correlated by the Gordon–Taylor equation. Phase separation, which was characterized by lower critical solution temperature (LCST) behavior, was found to occur when blends were heated to elevated temperatures.     

Poly(ethylene oxide)/poly(methyl methacrylate) blends: Influence of tacticity of poly(methyl methacrylate) on blend structure and miscibility

The influence of different configurations of poly(methyl methacrylate) on the miscibility and superstructure of poly(ethylene oxide)/poly(methyl methacrylate) (PEO/PMMA) blends was examined using small-angle X-ray scattering and differential scanning calorimetry. The blends prepared by solution casting were isothermally crystallized at 48°C. The miscibility, the melting behaviour, the glass transition temperature and the structural parameters of the blends were strongly dependent on the tacticity and blend composition. The small-angle X-ray intensity profiles were analysed using a recently developed methodology. For the poly(ethylene oxide)/atactic poly(methyl methacrylate) (PEO/APMMA) and poly(ethylene oxide)/syndiotactic poly(methyl methacrylate) (PEO/SPMMA) blends, the long period and the amorphous and transition region thicknesses increased with increase of PMMA content, whereas for the poly(ethylene oxide)/isotactic poly(methyl methacrylate) (PEO/IPMMA) blends they are independent of composition. The structural properties of the blends were attributed to the presence of non-crystallizable material in the interlamellar or interfibrillar regions, depending on PMMA tacticity. From the glass transition and melting temperatures, it has been supposed that one homogeneous amorphous phase is present in the case of PEO/APMMA and PEO/SPMMA blends and that the PEO/IPMMA amorphous system is phase-separated. The free-volume contribution to the energy of mixing for the various tactic PMMAs is hypothesized to be responsible for the difference in mixing behaviour.     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6‐naphthalate)/poly(pentamethylene terephthalate)/poly(ether imide) (PEN/PPT/PEI) blends were studied by differential scanning calorimetry (DSC), optical microscopy (OM), proton nuclear magnetic resonance imaging (¹H‐NMR), and wide‐angle X‐ray diffraction (WAXD). OM and DSC results from ternary blends revealed the immiscibility of PEN/PPT/PEI blends, but ternary blends of all compositions were phase‐homogeneous following heat treatment at 300°C for over 60 min. Annealing samples at 300°C yielded an amorphous blend with a clear and single T_g at the final state. Experimental data from ¹H‐NMR revealed that PEN/PPT copolymers (ENPT) were formed by the so‐called transesterification. The effect of transesterification on glass transition and crystallization was discussed in detail. The sequence structures of the copolyester were identified by triad analysis, which showed that the mean sequence lengths became shorter and the randomness increased with heating time. The results reveal that a random copolymer improved the miscibility of the ternary blends, in which, the length of the homo segments in the polymer chain decreased and the crystal formation was disturbed because of the irregularity of the structure, as the exchange reaction proceeded. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3840–3849, 2006