Controlled mechanical and swelling properties of poly(vinyl alcohol)/sodium alginate blend hydrogels prepared by freeze–thaw followed by Ca2+ crosslinking

Poly(vinyl alcohol) (PVA)/sodium alginate (SA) blend hydrogels have immense potential for use as functional biomaterials. Understanding of influences of processing parameters and compositions on mechanical and swelling properties of PVA/SA blend hydrogels is very important. In this work, PVA/SA blend hydrogels with different SA contents were prepared by applying freeze–thaw method first to induce physical crosslinking of PVA chains and then followed by Ca²⁺ crosslinking SA chains to form interpenetrating networks of PVA and SA. The effects of number of freeze–thaw cycles, SA content and Ca²⁺ concentration on mechanical properties, swelling kinetics, and pH‐sensitivity of the blend hydrogels were investigated. The results showed that the blend hydrogels have porous sponge structure. Gel fraction, which is related to crosslink density of the blend hydrogels, increased with the increase of freeze–thaw cycles and strongly depended on SA content. The SA content exerts a significant effect on mechanical properties, swelling kinetics, and pH‐sensitivity of the blend hydrogels. The number of freeze–thaw cycles has marked impact on mechanical properties, but no obvious effect on the pH‐sensitivity of the PVA/SA blend hydrogels. Concentration of CaCl₂ aqueous solution also influences mechanical properties and pH‐sensitivity of the blend hydrogel. By altering composition and processing parameters such as freeze–thaw cycles and concentration of CaCl₂ aqueous solution, the mechanical properties and pH‐sensitivity of PVA/SA blend hydrogels can be tightly controlled. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The Effect of glycerol on the crystalline,thermal, and tensile properties of CaCl2‐doped starch/PVA films

Starch/poly(vinyl alcohol) (PVA) films with the addition of 10 wt% CaCl₂ and various content of glycerol were prepared. The effect of glycerol on the crystalline, thermal, and tensile properties of CaCl₂‐doped starch/PVA films was studied by X‐ray diffraction, thermogravimetric analysis (TGA), and tensile testing, respectively. The effect of glycerol on the miscibility of CaCl₂‐doped starch/PVA films was studied by scanning electron microscopy. The CaCl₂‐doped starch/PVA film became more homogeneous after the addition of glycerol. The addition of glycerol would increase the crystallinity of CaCl₂‐doped starch/PVA film. With the addition of 10 wt% glycerol and 10 wt% CaCl₂, the starch/PVA film showed the highest degree of crystallinity. The TGA results show that the thermal stability of CaCl₂‐doped starch/PVA film increased after the addition of glycerol. The toughness of CaCl₂‐doped starch/PVA films was enhanced with the addition of glycerol. The starch/PVA film with the addition of 10 wt% CaCl₂ and 20 wt% glycerol showed the tensile strength of 17 MPa and the elongation at break of 428%. Moreover, the water sorption of CaCl₂‐doped starch/PVA film decreased after the addition of glycerol at the low and intermediate relative humidity of 33 and 54%. POLYM. COMPOS., 37:3191–3199, 2016. © 2015 Society of Plastics Engineers     

Silicon dioxide/poly(vinyl alcohol) composite hydrogels with high mechanical properties and low swellability

Poly(vinyl alcohol) (PVA) hydrogels with tissue-like viscoelasticity, excellent biocompatibility, and hydrophilicity have been considered as promising cartilage replacement materials. However, the low mechanical properties of pure PVA hydrogels limit their applications for bearing complicated loads. Herein, we report silicon dioxide (SiO₂)/PVA composite hydrogels fabricated by fabricated cyclically freezing/thawing the aqueous mixture of PVA and methyltrimethoxysilane (MTMS). MTMS hydrolyzes and forms SiO₂ particles in situ to reinforce PVA hydrogel. Meanwhile, silanol group condenses with hydroxyl groups of PVA and chemically bonds with PVA. The resulting SiO₂/PVA hydrogels exhibit much better mechanical properties than bare PVA hydrogel. In addition, the composite hydrogels keep very low swellable property. This prepared composite hydrogels are promising in a variety of biomedical applications such as artificial articular cartilage, drug delivery, and biosensors. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46895.     

Gelation of a new hydrogel system of atactic‐poly(vinyl alcohol)/NaCl/H2O

a‐PVA/NaCl/H₂O hydrogels have been prepared by gelation of aqueous atactic‐poly(vinyl alcohol) (a‐PVA) solutions in the presence of NaCl. The gelling temperature, melting temperature and the preservation of water of the hydrogels have been measured. The effect of the addition of NaCl to the hydrogels on gelling temperature and melting temperature is marked when the NaCl concentration is over a certain value. High NaCl concentration favours high‐melting‐point hydrogels. When the NaCl concentration is high enough (such as 11%), high‐melting‐point and white turbid opaque a‐PVA/NaCl/H₂O hydrogels can be prepared, regardless of the PVA concentration. Similarly, the low gelling temperature of a‐PVA/NaCl/H₂O solutions comes from low NaCl concentration, while high gelling temperature ranges from 50 to 70 °C when the NaCl concentration is 11%. In appearance, the types of syneresis of a‐PVA/NaCl/H₂O are χ‐type or a mixture of χ‐ and n‐types; water release of the hydrogels is slowed down by the addition of NaCl. © 2002 Society of Chemical Industry     

Swelling behavior of sulfonated polyacrylamide nanocomposite hydrogels in electrolyte solutions: comparison of theoretical and experimental results

Nanocomposite hydrogels were prepared by cross-linking of aqueous solutions of sulfonated polyacrylamide/sodium montmorillonite with chromium triacetate as ionic cross-linker. The effect of montmorillonite content on equilibrium swelling in NaCl and CaCl₂ solutions, ultimate storage modulus and effective cross-link density was evaluated. The limiting storage modulus of the nanocomposite (NC) hydrogels dropped by increasing montmorillonite content up to 1,000?ppm, and then it increased by further montmorillonite loading. A mechanism is proposed for the formation of PAMPS/Na⁺-MMT/Cr³⁺ NC hydrogels. According to this mechanism, the drop in limiting storage modulus of the NC gels at low Na⁺-MMT concentration is due to ionic interactions between the negative layers of sodium montmorillonite and Cr³⁺, leading to decreased cross-link density. However, the increase of the limiting storage modulus of the NC gels at high clay concentration results from the strong interactions between the polyacrylamide chains and clay platelets. The equilibrium swelling ratio of the NC networks decreased with increase of montmorillonite content in both aqueous NaCl and CaCl₂ solutions. In addition, the experimental swelling data of these NC hydrogels were described by a modified Flory?CRehner theory. The modified model was sensitive to montmorillonite concentration and it described adequately the swelling data for NC gels in NaCl solutions. Nevertheless, theoretical predictions showed some deviations from experimental results for swelling of NC hydrogels in CaCl₂ solutions.     

Tailoring Unidirectional Water-Penetration Janus Fabric with Surface Electrospun Deposition

This paper provides a new method to fabricate an integrated Janus fabric that has excellent unidirectional water-penetration property. Based on commercial polyester fabric that is pretreated with CaCl₂ solution, polyvinyl alcohol/sodium alginate (PVA/SA) solution is deposited directly on the fabric via electrospinning and in situ chelated with Ca²⁺ contained in the fabric. The in situ formed PVA/SA gel coating not only transfers the surface of polyester fabric from hydrophobic to hydrophilic but also retains original porous structure of polyester fabric. As the water droplet contacts with unelectrospun side of modified polyester fabric (M-PET) pretreated with 10 wt% CaCl₂, it penetrates through the M-PET within 1 s from unelectrospun side to electrospun side after application, and disappears on unelectrospun side within 2 s, and in turn, droplet spreads out on electrospun side of M-PET within 2 s after application and no penetration occurs. The M-PET pretreated with CaCl₂ solution has outstanding antistatic property, vapor, and air permeability. The impact of ratio (v/v) of the PVA and SA solution and the concentration of CaCl₂ pretreating solution on properties of the M-PET are investigated.     

Thermosensitive and ampholytic hydrogels for salt solution

A series of N‐isopropylacrylamide/[[3‐(methacryloylamino)propyl]dimethy(3‐sulfopropyl)ammonium hydroxide] (NIPAAm/MPSA) copolymer hydrogels were prepared with various compositions. Swelling of the hydrogels in water, aqueous NaCl, KCl, CaCl₂, and MgCl₂ solutions was studied. NIPAAm/MPSA hydrogels have a higher degree of swelling in water and salt solutions than that of poly(N‐isopropylacrylamide) (PNIPAAm). Also, NIPAAm/MPSA hydrogels are more salt resistant when deswelling in salt solutions. For <7 mol % MPSA, the formed hydrogels retain both temperature reversibility and high swelling. A higher content of MPSA (>11 mol %) leads to better salt resistance but a decrease in thermosensitivity. The swelling of NIPAAm/MPSA hydrogel in 0.05M NaCl is non‐Fickian. In NaCl and KCl aqueous solutions, the zwitterionic hydrogels do not show obvious antipolyelectrolyte swelling behavior, whereas in divalent salt CaCl₂ and MgCl₂ solutions, the swelling ability of NIPAAm/MPSA hydrogels is enhanced at low salt concentration, then decreases with further increase in salt concentration. The lower critical solution temperatures of NIPAAm/MPSA hydrogels are also affected by concentrated salt solution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2032–2037, 2003     

Preparation and characterization by radiation of hydrogels of PVA and PVP containing Aloe vera

In these studies, hydrogels for wound dressing were made from a mixture of Aloe vera, poly(vinyl alcohol) (PVA) and poly(N‐vinylpyrrolidone) (PVP) by freeze‐thaw, gamma‐ray irradiation, or a two‐step process of freeze‐thaw and gamma‐ray irradiation. Physical properties, such as gelation, water absorptivity, gel strength and degree of water evaporation were examined to evaluate the applicability of these hydrogels to wound dressing. The PVA:PVP ratio was 6:4, and the dry weight of Aloe vera was in the range of 0.4‐1.2 wt %. The solid concentration of PVA/PVP/Aloe vera solution was 15 wt %. Mixtures of PVA/PVP/Aloe vera were exposed to gamma irradiation doses of 25, 35 and 50 kGy to evaluate the effect of irradiation dose on the physical properties of the hydrogels. Gel content and gel strength increased as the concentration of Aloe vera in PVA/PVP/Aloe vera decreased and as irradiation dose increased and freeze‐thaw was repeated. Swelling degree was inversely proportional to gel content and gel strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1612–1618, 2004     

Pectin-based surperabsorbent hydrogels crosslinked by some chemicals: synthesis and characterization

Summary Synthesis of superabsorbent hydrogels from pectin was investigated using three kinds of crosslinkers, CaCl₂, ethylene glycol diglycidyl ether (EGE), and glutaraldehyde (GA). Among them, GA was the most suitable to attain high absorbency, reaching ca. 500 g/g in pure water. On the contrary, hydrogels crosslinked by CaCl₂ and EGE absorbed much less water, their maximum absorbency was around 200 g/g and 40 g/g, respectively. Absorbency in 0.9% NaCl solution of hydrogel crosslinked by GA was as low as 15 g/g, which indicates absorbency of hydrogels in the present study is sensitive to salt concentration. Biodegradability of pectin-based hydrogels in activated sludge at 25 °C for 18 days was 60–65%.     

Preparation and Characterization of Plasma-Derived Fibrin Hydrogels Modified by Alginate di-Aldehyde

Fibrin hydrogels are one of the most popular scaffolds used in tissue engineering due to their excellent biological properties. Special attention should be paid to the use of human plasma-derived fibrin hydrogels as a 3D scaffold in the production of autologous skin grafts, skeletal muscle regeneration and bone tissue repair. However, mechanical weakness and rapid degradation, which causes plasma-derived fibrin matrices to shrink significantly, prompted us to improve their stability. In our study, plasma-derived fibrin was chemically bonded to oxidized alginate (alginate di-aldehyde, ADA) at 10%, 20%, 50% and 80% oxidation, by Schiff base formation, to produce natural hydrogels for tissue engineering applications. First, gelling time studies showed that the degree of ADA oxidation inhibits fibrin polymerization, which we associate with fiber increment and decreased fiber density; moreover, the storage modulus increased when increasing the final volume of CaCl₂ (1% w/v) from 80 µL to 200 µL per milliliter of hydrogel. The contraction was similar in matrices with and without human primary fibroblasts (hFBs). In addition, proliferation studies with encapsulated hFBs showed an increment in cell viability in hydrogels with ADA at 10% oxidation at days 1 and 3 with 80 µL of CaCl₂; by increasing this compound (CaCl₂), the proliferation does not significantly increase until day 7. In the presence of 10% alginate oxidation, the proliferation results are similar to the control, in contrast to the sample with 20% oxidation whose proliferation decreases. Finally, the viability studies showed that the hFB morphology was maintained regardless of the degree of oxidation used; however, the quantity of CaCl₂ influences the spread of the hFBs.     

Thermally crosslinked anionic hydrogels composed of poly(vinyl alcohol) and poly(γ‐glutamic acid): Preparation,characterization, and drug permeation behavior

pH‐sensitive anionic hydrogels composed of poly(vinyl alcohol) (PVA) and poly(γ‐glutamic acid) (γ‐PGA) were prepared by the freeze drying method and thermally crosslinked to suppress hydrogel deformation in water. The physical properties, swelling, and drug‐diffusion behaviors were characterized for the hydrogels. In the equilibrium swelling study, PVA/γ‐PGA hydrogels shrunk in pH regions below the pK_a (2.27) of γ‐PGA, whereas they swelled above the pK_a. In the drug‐diffusion study, the drug permeation rates of the PVA/γ‐PGA hydrogels were directly proportional to their swelling behaviors. The cytocompatibility test showed no cytotoxicity of the PVA/γ‐PGA hydrogels for the 3T3 fibroblast cell lines. The results of these studies suggest that hydrogels prepared from PVA and γ‐PGA could be used as orally administrable drug‐delivery systems. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of poly(vinyl alcohol)/poly(acrylic acid)/TiO2/carbon nanotube composite nanofibers and their photobleaching properties

The composite nanofibers of poly(vinyl alcohol) (PVA)/poly(acrylic acid) (PAAc)/titanium(IV) oxide (TiO₂) were prepared by electrospinning for a novel photocatalytic treatment of waste water. To improve the photoelectronic properties of PVA/PAAc/TiO₂ composite nanofibers, carbon nanotubes (CNTs) were used as an additive. The TiO₂ and CNTs were immobilized in the PVA/PAAc hydrogels as electrospun nanofibers for an easier recovery after the wastewater treatment. The improved efficiency of pollutant dye removal was observed at pH 10 due to the pH-sensitive swelling behavior of the PVA/PAAc/TiO₂/CNTs composite nanofibers. The photocatalytic activity of TiO₂ was improved noticeably by applying electric field to the CNTs-embedded composite nanofibers.     

3D gel printing of magnetic hydrogel scaffolds assisted by in-situ gelation in a water level-controlled crosslinker bath

Polyvinylalcohol/chitosan (PVA/CS) is an excellent dual-network hydrogel material, but some significant challenges remain in fabricating composites with specific structures. In this study, 3D gel printing (3DGP) combined with a water-level controlled crosslinker bath was proposed for the rapid in-situ prototyping of PVA/CS/Fe₃O₄ magnetic hydrogel scaffolds. Specifically, the PVA/CS/Fe₃O₄ hydrogels were extruded into the crosslinker water to achieve rapid in-situ gelation, improving the printability of hydrogel scaffolds. The effect of the PVA/CS ratio on the rheological and mechanical properties of dual-network magnetic hydrogels was evaluated. The printing parameters were systematically optimized to facilitate the coordination between the crosslinking water bath and printer. The different crosslinking water baths were investigated to improve the printability of PVA/CS/Fe₃O₄ hydrogels. The results showed that the printability of the sodium hydroxide (NaOH) crosslinker was significantly better than that of sodium tripolyphosphate (TPP). The magnetic hydrogels (PVA: CS= 1: 1) crosslinked by NaOH had better compressive strength, swelling rate, and saturation magnetization of 1.17 MPa, 92.43%, and 22.19 emu/g, respectively. The MC3T3-E1 cell culture results showed that the PVA/CS/Fe₃O₄ scaffolds promoted cell adhesion and proliferation, and the scaffolds crosslinked by NaOH had superior cytocompatibility. 3DGP combined with a water-level controlled crosslinker bath offers a promising approach to preparing magnetic hydrogel materials.     

Preparation and characterization by radiation of poly(vinyl alcohol) and poly(N‐vinylpyrrolidone) hydrogels containing aloe vera

In these studies, hydrogels for wound dressings were made from a mixture of aloe vera and poly(vinyl alcohol) (PVA)/poly(N‐vinylpyrrolidone) (PVP) by freezing and thawing, γ‐Ray irradiation, or a two‐step process of freezing and thawing and γ‐ray irradiation. We examined the physical properties, including gelation, water absorptivity, gel strength, and degree of water evaporation, to evaluate the applicability of these hydrogels for wound dressings. The PVA:PVP ratio was 6:4, the dry weight of aloe vera was in the range 0.4–1.2 wt %, and the solid concentration of the PVA/PVP/aloe vera solution was 15 wt %. We used γ radiation doses of 25, 35, and 50 kGy to expose mixtures of PVA/PVP/aloe vera to evaluate the effect of radiation dose on the physical properties of the hydrogels. Gel content and gel strength increased as the concentration of aloe vera in the PVA/PVP/aloe vera gels decreased and as radiation dose increased and the number of freeze–thaw cycles was increased. The swelling degree was inversely proportional to the gel content and gel strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1477–1485, 2003     

Effect of degree of cross-linking on swelling and on drug release of low viscous chitosan/poly(vinyl alcohol) hydrogels

In the present work, a series of cross-linked LVCS/PVA hydrogels with various feed compositions were prepared using glutaraldehyde as cross-linking agent. The prepared hydrogels were used for dynamic and equilibrium swelling studies. The swelling behavior of these hydrogels was investigated as functions of effect of pH, polymeric compositions and degree of cross-linking. Swelling studies were performed in 0.05 M USP phosphate buffer solutions of varying pH 1.2, 5.5, 6.5 and 7.5. Results showed that swelling increased by increasing PVA contents in the structure of hydrogels in solutions of higher pH values. This is due to the presence of more hydroxyl groups (–OH) in the PVA structure. On the other hand, by increasing LVCS contents, swelling increased in a solution of acidic pH and it is due to ionization of amino groups (–NH₂), but this swelling was not significant. Swelling of hydrogels was decreased with increase in cross-linking ratio due to tighter hydrogel structure. Porosity and sol–gel fraction were also investigated. It was found that with increase in LVCS and PVA contents porosity and gel fraction increased, whereas by increasing glutaraldehyde content gel fraction increased and porosity decreased. Diffusion coefficient (D) and network parameters, i.e., the average molecular weight between cross-links (M _C), solvent interaction parameters (χ), polymer volume fraction in swollen state (V _2S) and cross-linked density (q) were calculated using Flory–Rehner theory. Selected samples were loaded with model drug diphenhydramine HCl. The release of diphenhydramine HCl was studied for 12 h period in 0.05 M USP phosphate buffer solutions of varying pH 1.2, 5.5 and 7.5. It was observed that drug release increased with increasing PVA contents in the hydrogels, while release of drug decreased as the ratio of cross-linking agent increased in the hydrogel structure owing to strong physical entanglements between polymers. The release mechanisms were studied by fitting experimental data to model equations like zero order, first order, Higuchi and Peppas. Results showed that the kinetics of drug release from hydrogels in buffer solutions of pH 1.2, 5.5 and 7.5 was mainly non-fickian diffusion. Hydrogels were characterized by Fourier transform infrared and X-ray diffraction to confirm the structure and study the crystallinity of hydrogel, respectively.     

Properties of biodegradable hydrogels prepared by γ irradiation of microbial poly(ϵ-lysine) aqueous solutions

Poly(?-lysine) (PL) hydrogels have been prepared by means of γ irradiation of PL produced by Streptomyces albulus in aqueous solutions. When the dosage of γ irradiation was 70 kGy or more and the concentration of PL in water was 1–7 wt %, transparent hydrogels (opaque hydrogels for 1–3 wt % PL concentration) could be produced. In the case of 70 kGy of γ irradiation and 5 wt % PL concentration, the specific water content (wt of absorbed water/wt of dry hydrogel) of the PL hydrogel was approximately 160. Specific water contents of PL hydrogels decreased markedly with an increase in the dosage of γ irradiation. The specific water contents were increased with an increase in PL concentration in the irradiated solution. This result indicates the presence of a radical scavenger in the PL solution. Swelling equilibria of PL hydrogels were measured in water or in aqueous solutions of various pHs or concentrations of NaCl, Na₂SO₄, and CaCl₂. Under acid conditions, the PL hydrogel swelled due to the ionic repulsion of the protonated amino groups in the PL molecules. The degree of deswelling in electrolyte solution was smaller than that of other ionic hydrogels [poly(γ-glutamic acid), poly(acrylic acid) etc.]. In addition, the enzymatic degradations of PL hydrogel were studied at 40°C and pH 7.0 in an aqueous solution of the neutral protease [Protease A (Amano)] produced from Aspergillus oryzae. The rate of enzymatic degradation of the respective PL hydrogels was much faster than the rate of simple hydrolytic degradation. The rate of enzymatic degradation decreased with the increase in γ-irradiation dose during preparation of the PL hydrogel. © 1995 John Wiley & Sons, Inc.     

A Model of Mechanotransduction in Polyvinyl Alcohol-Based Composite Hydrogels for Regulating Musculoskeletal Differentiation

In regenerative medicine, extracellular matrix (ECM)-inspired materials are currently being explored to imitate mechanotransduction pathways and control cell fate. In musculoskeletal tissue regeneration, enhancing mechano-biological signals require biomaterials that are both biocompatible and viscoelastic and can retain water content. Herein, based on these requirements, various polyvinyl alcohol (PVA)-based composite hydrogels, reinforced by polyhydroxy butyrate (PHB) nanofibers, are proposed to differentiate equine adipose-derived stem cells for musculoskeletal regeneration. To study the role of fiber embedding in improving scaffold properties, different nanofiber assemblies, including chopped short ones with random orientation (PVA_S), single-layer (PVA_L1), and double-layer membranes (PVA_L2) are positioned into the PVA matrix. PHB reinforcements negatively affect swelling and positively enhanced phase transition temperatures and crystallinity of PVA hydrogel. According to mechanical analysis results, compositing with PHB nanofibrous layers strengthen the PVA matrix due to some restrictions on PVA chain mobility. Gene expression investigations also reveal that higher matrix stiffness after layering with two PHB membranes (PVA_L2) promotes osteogenesis, while the random addition of short-chapped fibers (PVA_S) facilitate tenogenic differentiation. As a consequence of the findings, fiber placement is crucial to the mechanical properties of composite hydrogels that ultimately control musculoskeletal differentiation signals through mechanosensing pathways.     

Crosslinked poly(vinyl alcohol)/carboxymethyl chitosan hydrogels for removal of metal ions and dyestuff from aqueous solutions

Hydrogels composed of poly(vinyl alcohol) (PVA) and carboxymethyl chitosan (CMCh) were synthesized via ultraviolet (UV) irradiation that can be used in several industrial fields. Several analysis tools were used to characterize the physical and thermal properties of CMCh/PVA hydrogels namely FT‐IR, scanning electron microscope (SEM), XRD, thermogravimetric analysis (TGA), and differential scanning calorimetery (DSC). TGA results showed that CMCh/PVA hydrogels are thermally more stable than CMCh and their thermal stability increases as PVA content increases in the hydrogel. Also, DSC results showed that CMCh/PVA hydrogels are at least partial miscible blends. Moreover, the swelling behavior of the CMCh/PVA hydrogels was studied in different buffered solutions and in different salt solutions at various concentrations. CMCh/PVA hydrogels swell much more than CMCh especially at alkaline pH. Both metal and dye uptake were studied for CMCh/PVA hydrogels. The hydrogels adsorb much more dyestuff and metal ions like Cu²⁺, Cd²⁺, and Co²⁺ than CMCh itself. Much dyestuff and metal ions are adsorbed by the hydrogels as PVA content increases in the hydrogel. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Comparative study of PEO and PVA hydrogels for removal of methylene blue dye from wastewater

In this study, poly(vinyl alcohol) (PVA) and poly(ethylene oxide) (PEO) hydrogels were synthesized and evaluated as adsorbent for dye removal from wastewater using methylene blue (MB) in aqueous solution as probe. PEO samples were photochemically prepared by varying irradiation time (1–16 h), while PVA samples were synthetized with different concentration of glutaraldehyde (GA) (0.03–0.48%). The obtained hydrogels were obtained through the analysis of a swelling test, scanning electron microscopy, and adsorption studies. PEO hydrogels adsorption capacity was dependent on the irradiation time, while the PVA hydrogel adsorption capacity reduces with GA concentration. Both hydrogels demonstrated a Langmuir isotherm adsorption model at the equilibrium and pseudo‐second order kinetic fits properly. pH studies showed that when pH reaches 12, the adsorbed MB amount is close to 8 and 2 times higher than pH = 2 both hydrogels. Photochemical preparation of hydrogels shows an easier way of tuning their properties in order to maximize dye removal. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45043.     

Preparation and characterization of PVA/PVP/glycerin/antibacterial agent hydrogels using <Emphasis Type="Italic">γ</Emphasis>-irradiation followed by freeze-thawing

Hydrogels for wound dressings from a mixture of poly(vinyl alcohol) (PVA), poly(N-vinylpyrrolidone) (PVP), glycerin and an antibacterial agent were obtained by a γ-irradiation combined with freeze-thawing. The physical properties such as the gelation and swelling degree of the hydrogels were examined. When the PVP/PVA ratio was 6: 4 (wt%) and prepared by combined irradiation and freeze-thawing, it showed an excellent swelling capacity (>1,200%). The antibacterial effect of the hydrogels containing the antibacterial agents was observed to be effective as the concentration of antibacterial agents increased. The results demonstrated that hydrogel in a proper blending ratio could be used as a wound dressing that can accelerate wound healing with an antibacterial effect.