Comparative study of the influence of various melt-treatment methods on hot deformation behavior of 3003 Al alloy

3003 Al alloy samples with various metallurgical qualities were obtained by various melt-treatment methods and were deformed by isothermal compression in the deformation temperature range of 300°C to 500°C at strain rates between 0.0l and 10.0 s⁻¹ with a Gleeble-1500 thermal simulator. The results show that there is a close relationship between melt-treatment and subsequent thermal deformation. The hot deformation activation energy (Q) bears a linear relationship with the inclusion content (H) of 3003 Al alloy prepared by various melt-treatment methods, that is Q = 35.62 H + 171.58. The activation energy of the 3003 Al alloy prepared by the highly efficient melt-treatment is the lowest (174.62 kJ·mol⁻¹), which is beneficial to the material hot plastic deformation. The critical strain of the 3003 Al alloy prepared by various melt-treatment methods is investigated through the work hardening rate. Finally, the critical conditions of the investigated alloy were determined to predict the occurrence of dynamic recrystallization.     

Optimization of thermal processing parameters of Ti555211 alloy using processing maps based on Murty criterion

Isothermal compression testing of Ti555211 titanium alloys was carried out at deformation temperatures from 750 to 950 °C in 50 °C intervals with a strain rate of0.001–1.000 s~(-1). The high-temperature deformation behavior of the Ti555211 alloy was characterized by analysis of stress–strain behavior, kinetics and processing maps. A constitutive equation was formulated to describe the flow stress as a function of deformation temperature and strain rate, and the calculated apparent activation energies are found to be 454.50 and 207.52 k J mol~(-1)in the a b-phase and b-phase regions, respectively. A processing map based on the Murty instability criterion was developed at a strain of 0.7. The maps exhibit two domains of peak efficiency from 750 to 950 °C. A *60 % peak efficiency occurs at 800–850 °C/0.001–0.010 s~(-1). The other peak efficiency of *60 % occurs at C950 °C/0.001–0.010 s~(-1), which can be considered to be the optimum condition for high-temperature working of this alloy.However, at strain rates of higher than 1.000 s~(-1)and deformation temperatures of 750 and 950 °C, clear process flow lines and bands of flow localization occur in the hightemperature deformation process, which should be avoided in Ti555211 alloy hot processing. The mechanism in stability domain and instability domain was also discussed.     

3003铝合金热变形行为

采用不同熔体处理工艺获得3种不同冶金质量的3003铝合金,通过Gleeble-1500热模拟试验机对3003铝合金进行变形温度为300℃~500℃,应变速率为0.01s-1~10s-1高温等温压缩实验。结果表明,3003铝合金具有正的应变速率敏感性,热变形激活能Q与含杂量H呈线性关系,经高效综合处理的3003铝合金热变形激活能最低为174.62kJ.mol-1,有利于材料热塑性变形。采用加工硬化率计算不同熔体处理的3003铝合金的临界应变值,获得了经不同熔体处理的3003铝合金发生动态再结晶的临界条件。     

Hot deformation behavior of Al–9.0Mg–0.5Mn–0.1Ti alloy based on processing maps

Hot deformation behavior of extrusion preform of the spray-formed Al–9.0Mg–0.5Mn–0.1Ti alloy was studied using hot compression tests over deformation temperature range of 300–450 °C and strain rate range of 0.01–10 s^?1. On the basis of experiments and dynamic material model, 2D processing maps and 3D power dissipation maps were developed for identification of exact instability regions and optimization of hot processing parameters. The experimental results indicated that the efficiency factor of energy dissipate (η) lowered to the minimum value when the deformation conditions located at the strain of 0.4, temperature of 300 °C and strain rate of 1 s^?1. The softening mechanism was dynamic recovery, the grain shape was mainly flat, and the portion of high angle grain boundary (>15°) was 34%. While increasing the deformation temperature to 400 °C and decreasing the strain rate to 0.1 s^?1, a maximum value of η was obtained. It can be found that the main softening mechanism was dynamic recrystallization, the structures were completely recrystallized, and the portion of high angle grain boundary accounted for 86.5%. According to 2D processing maps and 3D power dissipation maps, the optimum processing conditions for the extrusion preform of the spray-formed Al–9.0Mg–0.5Mn–0.1Ti alloy were in the deformation temperature range of 340–450 °C and the strain rate range of 0.01–0.1 s^?1 with the power dissipation efficiency range of 38%–43%.     

Effect of initial microstructure on hot workability of 7085 aluminum alloy

The hot workability of 7085 aluminum alloys with different initial microstructures (as-homogenized and as-solution treated) was studied by isothermal compression tests at the deformation temperature ranging from 300 to 450 °C and the strain rate ranging from 0.0001 to 1 s^?1. The strain rate sensitivity of the alloy was evaluated and used for establishing the power dissipation maps and instability maps on the basis of the flow stress data. The results show that the efficiency of power dissipation for the as-homogenized alloy is lower than that of the as-solution treated alloy. The deformation parameters of the dynamic recrystallization for the as-homogenized and as-solution treated alloy occur at 400 °C, 0.01 s^?1 and 450 °C, 0.001 s^?1, respectively. The flow instability region of the as-homogenized alloy is narrower than that of the as-solution treated alloy. These differences of the alloys with two different initial microstructures on the processing maps are mainly related to the dynamic precipitation characteristics.     

Deformation behavior and processing maps of Mg-Zn-Y alloy containing I phase at elevated temperatures

The microstructure and mechanical properties of extruded Mg-Zn alloy containing Y element were investigated in temperature range of 300–450 °C and strain rate range of 0.001–1 s^?1 through hot compression tests. Processing maps were used to indicate optimum conditions and instability zones for hot deformation of alloys. For Mg-Zn and Mg-Zn-Y alloys, peak stress, temperature and strain rate were related by hyperbolic sine function, and activation energies were obtained to be 177 and 236 kJ/mol, respectively. Flow curves showed that the addition of Y element led to increase in peak stress and decrease in peak strain, and indicated that DRX started at lower strains in Mg-Zn-Y alloy than in Mg-Zn alloy. The stability domains of Mg-Zn-Y alloy were indicated in two domains as 1) 300 °C, 0.001 s^?1; 350 °C, 0.01–0.1 s^?1 and 400 °C, 0.01 s^?1 and 2) 450 °C, 0.01–0.1 s^?1. Microstructural observations showed that DRX was the main restoration mechanism for alloys, and fully dynamic recrystallization of Mg-Zn-Y alloy was observed at 450 °C. The instability domain in Mg-Zn-Y alloy was located significantly at high strain rates. In addition, the instability zone width of Mg-Zn and Mg-Zn-Y alloys increased with increasing strain, and cracks, twins and severe deformation were considered in these regions.     

A Study on the Hot Deformation Behavior of Cast Mg-4Sn-2Ca (TX42) Alloy

The hot deformation behavior of as-cast Mg-4Sn-2Ca (TX42) alloy has been studied using compression tests in the temperature range of 300°C to 500°C, and strain rate range of 0.0003 s^?1 to 10 s^?1. Based on the flow stress data, a processing map has been developed, which exhibited two domains of dynamic recrystallization in the temperature and strain rate ranges: (I) 300°C to 380°C and 0.0003 s^?1 to 0.001 s^?1, and (II) 400°C to 500°C and 0.004 s^?1 to 6 s^?1. While hot working may be conducted in either of these domains, the resulting grain sizes are finer in the first domain than in the second. The apparent activation energy values estimated by kinetic analysis of the temperature and strain rate dependence of flow stress in the domains 1 and 2 are 182 kJ/mol and 179 kJ/mol, respectively. Both the values are much higher than that for self-diffusion in pure magnesium, indicating that the thermally stable CaMgSn particles in the matrix cause significant back stress during the hot deformation of this alloy. The alloy exhibits a regime of flow instability at lower temperatures and higher strain rates, which manifested as flow localization.     

60NiTi合金的热压缩变形与显微组织演变（英文）

采用Gleeble-3500热模拟试验机对在变形温度500～650℃和应变速率0.001～1 s^-1条件下的60NiTi合金进行热压缩变形,分析其热变形行为和显微组织,建立变形本构模型,绘制热加工图。结果表明,当压缩温度升高或应变速率降低时,峰值应力减小。合金的热变形激活能为327.89 k J/mol,热加工工艺参数为变形温度600～650℃和应变速率0.005～0.05 s^-1。当变形温度升高时,合金的再结晶程度增大;当应变速率增大时,位错密度和孪晶数量增大,Ni₃Ti相易于聚集;Ni₃Ti析出相有利于诱发合金基体的动态再结晶。动态回复、动态再结晶和孪生是60NiTi合金热变形的主要机制。     

Effect of Initial Grain Size on the Dynamic Recrystallization of Hot Deformation for 3003 Aluminum Alloy

The 3003 aluminum alloys with four different initial grain sizes were deformed by isothermal compression in the range of deformation temperature 300–500 °C at strain rate 0.01–10.0 s^?1 with Gleeble-1500 thermal simulator. The results show that the smaller the initial grain size of the alloy, the greater the required deformation resistance, and the smaller the peak strain, which is conducive to the occurrence of dynamic recrystallization (DRX). The DRX critical strain increases with the decrease of the deformation temperature or the increase of the strain rate, and the DRX volume fraction increases with the decrease of the strain rate and the increase of the deformation temperature. The average grain size of 3003 aluminum alloy after deformation is smaller than that before deformation. The smaller the initial grain size, the lower the critical recrystallization strain. So the DRX is carried out more fully, contributing to the thermoplastic deformation of the alloy.     

Characterization of hot deformation and microstructure evolution of a new metastable β titanium alloy

The hot deformation characteristics of as-forged Ti?3.5Al?5Mo?6V?3Cr?2Sn?0.5Fe?0.1B?0.1C alloy within a temperature range from 750 to 910 °C and a strain rate range from 0.001 to 1 s^?1 were investigated by hot compression tests. The stress?strain curves show that the flow stress decreases with the increase of temperature and the decrease of strain rate. The microstructure is sensitive to deformation parameters. The dynamic recrystallization (DRX) grains appear while the temperature reaches 790 °C at a constant strain rate of 0.001 s^?1 and strain rate is not higher than 0.1 s^?1 at a constant temperature of 910 °C. The work-hardening rate θ is calculated and it is found that DRX prefers to happen at high temperature and low strain rate. The constitutive equation and processing map were obtained. The average activation energy of the alloy is 242.78 kJ/mol and there are few unstable regions on the processing map, which indicates excellent hot workability. At the strain rate of 0.1 s^?1, the stress?strain curves show an abnormal shape where there are two stress peaks simultaneously. This can be attributed to the alternation of hardening effect, which results from the continuous dynamic recrystallization (CDRX) and the rotation of DRX grains, and dynamic softening mechanism.     

Hot deformation and processing maps of as-sintered CNT/Al-Cu composites fabricated by flake powder metallurgy

The deformation behaviors of as-sintered CNT/Al-Cu composites were investigated by isothermal compression tests performed in the temperature range of 300?550 °C and strain rate range of 0.001?10 s^?1 with Gleeble 3500 thermal simulator system. Processing maps based on dynamic material model (DMM) were established at strains of 0.1?0.6, and microstructures before and after hot deformation were characterized by scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and high-resolution transmission electron microscopy (HRTEM). The results show that the strain has a significant influence on the processing maps, and the optimum processing domains are at temperatures of 375?425 °C with strain rates of 0.4?10 s^?1 and at 525?550 °C with 0.02?10 s^?1 when the strain is 0.6. An inhomogeneous distribution of large particles, as well as a high density of tangled dislocations, dislocation walls, and some sub-grains appears at low deformation temperatures and strain rates, which correspond to the instability domain. A homogeneous distribution of fine particles and dynamic recrystallization generates when the composites are deformed at 400 and 550 °C under a strain rate of 10 s^?1, which correspond to the stability domains.     

Cu-Ni-Si-P合金热变形行为及热加工图

采用高温等温压缩试验,对Cu?Ni?Si?P合金在应变速率0.01~5?1、变形温度600~800°C条件下的高温变形行为进行了研究,得出了该合金热压缩变形时的热变形激活能Q和本构方程。根据实验数据与热加工工艺参数构建了该合金的热加工图,利用热加工图对该合金在热变形过程中的热变形工艺参数进行了优化,并利用热加工图分析了该合金的高温组织变化。热变形过程中Cu?Ni?Si?P合金的流变应力随着变形温度的升高而降低,随着应变速率的提高而增大,该合金的动态再结晶温度为700°C。该合金热变形过程中的热变形激活能Q为485.6 kJ/mol。通过分析合金在应变为0.3和0.5时的热加工图得出该合金的安全加工区域的温度为750~800°C,应变速率为0.01~0.1 s?1。通过合金热变形过程中高温显微组织的观察,其组织规律很好地符合热加工图所预测的组织规律。     

Effect of Cr elimination on flow behavior and processing map of newly developed ECO-7175 aluminum alloy during hot compression

ECO-Al alloys are introduced as a game-changer for the aluminum industry and it is of utmost importance to determine the role of alloying elements in their processing characteristics. In this study, the effects of Cr on the hot deformation behavior of newly-developed ECO-7175 alloy were investigated. ECO-7175 samples with and without Cr were hot-compressed using a Gleeble simulator (temperature range of 350?500 °C and strain rates of 0.001?1 s^?1). The results were used to study the constitutive equations, the processing maps, and the microstructural evolution of the alloys. In Cr-containing alloy, the analysis of the deformation activation energy reveals that the rate-controlling mechanisms of the deformation change gradually from self-diffusion of Al (or diffusion of Mg in Al) to diffusion of Cr in Al by decreasing the Zener?Hollomon parameter. The analysis of the processing maps of Cr-containing alloy shows that the dynamic recrystallization (DRX) zone is limited to the deformation at high temperatures and low strain rates and expands with increasing applied strain. On the other hand, it is found that the self-diffusion of Al (or Mg in Al) is the only rate-controlling mechanism during hot deformation of Cr-free alloy in all processing conditions and its DRX zone is independent of the plastic strain.     

Processing map and microstructure evaluation of AA6061/Al2O3 nanocomposite at different temperatures

Hot compression behavior of Al6061/Al₂O₃ nanocomposite was investigated in the temperature range of 350–500 °C and the strain rate range of 0.0005–0.5 s^?1, in order to determine the optimum conditions for the hot workability of nanocomposite. The activation energy of 285 kJ/mol for the hot compression test is obtained by using hyperbolic sine function. By means of dynamic material model (DMM) and the corresponding processing map, safe zone for the hot workability of AA6061/Al₂O₃ is recognized at temperature of 450 °C and strain rate of 0.0005 s^?1 and at temperature of 500 °C and the strain rate range of 0.0005–0.5 s^?1, with the maximum power dissipation efficiency of 38%. Elongated and kinked grains are observed at 400 °C and strain rate of 0.5 s^?1 due to the severe deformation.     

Hot Compression Deformation Behavior and Processing Maps of Mg-Gd-Y-Zr Alloy

Hot compression deformation behavior and processing maps of the Mg-Gd-Y-Zr alloy were investigated in this paper. Compression tests were conducted at the temperature range from 300 to 450 °C and the strain rate range from 0.001 to 1.0 s^?1. It is found that the flow stress behavior is described by the hyperbolic sine constitutive equation in which the average activation energy of 251.96 kJ/mol is calculated. Through the flow stress behavior, the processing maps are calculated and analyzed according to the dynamic materials model. In the processing maps, the variation of the efficiency of the power dissipation is plotted as a function of temperature and strain rate. The instability domains of flow behavior are identified by the maps. The maps exhibit a domain of dynamic recrystallization occurring at the temperature range of 375-450 °C and strain rate range of 0.001-0.03 s^?1 which are the optimum parameters for hot working of the alloy.     

High temperature deformation and processing map of a NiTi intermetallic alloy

The deformation behavior of a 49.8 Ni-50.2 Ti (at pct) alloy was investigated using the hot compression test in the temperature range of 700 °C–1100 °C, and strain rate of 0.001 s^?1 to 1 s^?1. The hot tensile test of the alloy was also considered to assist explaining the related deformation mechanism within the same temperature range and the strain rate of 0.1 s^?1. The processing map of the alloy was developed to evaluate the efficiency of hot deformation and to identify the instability regions of the flow. The peak efficiency of 24–28% was achieved at temperature range of 900 °C–1000 °C, and strain rates higher than 0.01 s^?1 in the processing map. The hot ductility and the deformation efficiency of the alloy exhibit almost similar variation with temperature, showing maximum at temperature range of 900 °C–1000 °C and minimum at 700 °C and 1100 °C. Besides, the minimum hot ductility lies in the instability regions of the processing map. The peak efficiency of 28% and microstructural analysis suggests that dynamic recovery (DRV) can occur during hot working of the alloy. At strain rates higher than 0.1 s^?1, the peak efficiency domain shifts from the temperature range of 850 °C–1000 °C to lower temperature range of 800 °C–950 °C which is desirable for hot working of the NiTi alloy. The regions of flow instability have been observed at high Z values and at low temperature of 700 °C and low strain rate of 0.001 s^?1. Further instability region has been found at temperature of 1000 °C and strain rates higher than 1 s^?1 and at temperature of 1100 °C and all range of strain rates.     

ZL270LF铝合金的热变形行为与组织演变

通过热压缩实验研究了ZL270LF铝合金在变形量为70%,温度为300~550 ℃,应变速率为 0.01~10 s^-1范围的热变形行为,建立了流变应力本构方程模型,绘制出了二维热加工图,确定了最佳热加工区域,采用电子背散射衍射（EBSD）和透射电子显微镜（TEM）技术研究了该合金的组织演变规律。结果表明：ZL270LF铝合金的流变应力随变形温度的升高和应变速率的降低而降低,热变形激活能为309.05 kJ/mol,最优热加工区为温度470~530 ℃、应变速率为0.01~1 s^-1。该合金在热变形过程中存在3种不同的DRX机制,即连续动态再结晶（CDRX）、不连续动态再结晶（DDRX）和几何动态再结晶（GDRX）,其中CDRX是ZL270LF铝合金动态再结晶的主要机制。     

原位TiB2颗粒增强7075铝基复合材料的热压缩变形行为和显微组织演变

采用等温热压缩实验研究不同变形条件下(变形温度300～450℃、应变速率0.001～1 s?1)原位TiB2颗粒增强7075铝基复合材料的热成形行为、损伤机制和显微组织演变.结果表明,复合材料在低温和高应变速率下的主要损伤机制是颗粒断裂和界面脱粘,而在高温和低应变速率下主要是基体的韧窝断裂.此外,复合材料在高温、低应变...     

Hot Deformation Behavior and Processing Maps of 2099 Al-Li Alloy

Hot deformation behavior and processing maps of the 2099 Al-Li alloy are investigated by tensile test at the temperature range from 250 to 450 °C and the strain rate range from 0.001 to 5.0 s^?1. The typical true stress-true strain curves show that the flow stress increases with increasing the strain rate and decreasing the deforming temperature. All curves exhibit rapid work hardening at an initial stage of strain followed by remarkable dynamic softening. Based on the flow stress behavior, the processing maps are calculated and analyzed according to the dynamic materials model (DMM). The processing maps exhibit an instability domain in the temperature and strain rate ranges: T = 250-260 °C and \(\dot{\upvarepsilon }\)  = 0.1-0.5 s^?1. The maps also exhibit an optimum hot working condition in the stability domain that occurs in the temperature of 400 °C for a strain rate of 0.001 s^?1 and having a maximum efficiency of 60%. The microstructural examinations exhibit the occurrence of dynamic recovery (DRV) during hot deformation of the 2099 alloy which is the dominant softening mechanism in the alloy. The fracture behavior changes from a brittle fracture to a ductile fracture as strain rate decreases and temperature increases.     

Constitutive behavior,microstructural evolution and processing map of extruded Al–1.1Mn–0.3Mg–0.25RE alloy during hot compression

Hot compression tests of an extruded Al–1.1Mn–0.3Mg–0.25RE alloy were performed on Gleeble–1500 system in the temperature range of 300–500 °C and strain rate range of 0.01–10 s^?1. The associated microstructural evolutions were studied by observation of optical and transmission electron microscopes. The results show that the peak stress level decreases with increasing deformation temperature and decreasing strain rate, which can be represented by a Zener–Hollomon parameter in the hyperbolic-sine equation with the hot deformation activation energy of 186.48 kJ/mol. The steady flow behavior results from dynamic recovery whereas flow softening is associated with dynamic recrystallization and dynamic transformation of constituent particles. The main constituent particles are enriched rare earth phases. Positive purifying effects on impurity elements of Fe and Si are shown in the Al–1.1Mn–0.3Mg–0.25RE alloy, which increases the workability at high temperature. Processing map was calculated and an optimum processing was determined with deformation temperature of 440–450 °C and strain rate of 0.01 s^?1.