共查询到19条相似文献,搜索用时 156 毫秒
1.
2.
利用自主开发的离线模拟分析软件,结合唐钢超薄带钢生产现场各种工艺条件,对影响板形的因素进行了定量分析.结果表明:F4、F5轧机弯辊力对最终板凸度的影响大于F1~F3轧机;带材厚度对弯辊力作用效果的影响不明显.不同机架的PC角变化对板凸度的影响基本相同,随着PC角的增加,最终板凸度减小,且PC角越大,减小的趋势增强.F1~F5轧机中任一轧机轧制力的增大,最终板凸度近似成线性增加;下游机架轧制力的变化对板凸度的影响大于上游机架;轧制力的变化更容易导致薄规格产品产生板形不良. 相似文献
3.
在分析连轧机板形和板凸度变化后,考虑连板前段机架轧制规格厚者其平直度死区大,而技术进步要求成品凸度小,品种规格轧制分流。从经济技术角度提出对于特宽带钢轧机应该选择较简单的工作辊患装置和技术。 相似文献
4.
利用有限元分析软件ANSYS对轧机承载辊缝变形的仿真,分析轧机轧制力、弯辊力及工作辊窜辊对承载辊缝的凸度影响程度,结合现场机架间带钢的浪形,优化二级板形模型设定参数,实现轧机稳定轧制。实践证明,人工修正轧机负荷分配以及CVC轧辊位置,可更好地控制前机架比例凸度,满足后机架间平直度目标的要求,从而提高板凸度的命中率及轧机轧制的稳定性。 相似文献
5.
针对无取向硅钢热轧采用多种宽度连续混合编排条件进行同宽轧制的板形控制问题,采用ANSYS有限元软件结合1700热连轧机轧制工艺参数和实测的轧辊辊形,建立了辊系弹性有限元模型.仿真分析发现:在其它轧制条件相同情况下,轧制1300mm左右宽度无取向硅钢凸度最易超标和难以控制;弯辊力对1300mm宽度无取向硅钢的凸度和边降调控范围比1100mm硅钢分别增加56.8%和28.1%;1300mm同宽单位仿真发现,轧制单位中后期带钢整体凸度显著增大的主要原因在于采用常规工作辊的局部"猫耳朵"磨损导致边降显著,不仅中后期无取向硅钢边降不断增大,且占带钢整体凸度的比例不断增大,由前期的42.9%增加到中后期的50.9%和54.1%. 相似文献
6.
在带钢热轧机中装备有在线磨辊设备的成对交叉辊(PC)轧机可进行自由轧制,并得到良好的带钢凸度和板形控制。中厚板采用PC轧机轧制改善了产品质量并减少了轧制道次,提高了生产率,并通过降低板坯出炉温度,减少了能耗。在冷轧中采用PC轧机的预期效益是增大压下率和改善带钢板形(减少边部减薄)。 相似文献
7.
为掌握1 800 mm CSP轧机的板形调控特性,以某1 800 mm CSP轧机为研究对象,建立了不同机架的有限元模型。利用有限元模型分析了不同带钢宽度下的弯辊力与窜辊对带钢板廓的影响,计算出上、中、下游机架的板形调控特性,得出当前中游机架板形调控能力最强,上游次之,下游最弱,并且板形控制能力随着带钢宽度的减小而减小。根据弯辊与窜辊在当前板形控制中所占比例,得出CVC窜辊是当前凸度控制的主要手段。对现场实际窜辊数据进行分析,得出上游机架凸度控制能力不足,中游机架凸度控制能力偏大,同时,通过对不同宽度带钢窜辊数据的分析得出轧制窄带钢时更易出现凸度控制能力不足的情况。现场数据与有限元仿真结果相互验证,研究结论可以为现场的辊形改进提供较好的理论分析基础。 相似文献
8.
9.
10.
《冶金设备》2019,(5)
轧辊的热行为,特别是工作辊的热凸度及其变化是带钢轧制过程中的主要干扰因素之一,严重影响到轧制过程中尤其对薄板板形的控制。某厂二次冷轧机组主要生产极薄规格DR材产品,带钢最薄可达0. 1mm,由于该机组非冷连轧机组,轧制过程不连续,每卷带钢轧制间歇期较长,导致轧制区热凸度不稳定,影响生产的产品板形质量,故对该机组轧辊热行为研究是需要解决的重要问题。本文以该机组为研究对象,基于ANSYS有限元仿真软件,建立1#机架大小辊工作模式下工作辊温度场与热凸度有限元仿真模型,计算轧制过程中工作辊温度场和热凸度变化,为辊缝控制精度的补偿控制提供了依据,提高机组产品板形质量。 相似文献
11.
Shape Control Simulation on 4-High CVC Mill 总被引:2,自引:1,他引:1
WANGYing-rui YUANJian-guang LIUHong-min 《钢铁研究学报(英文版)》2005,12(2):25-32
Shapeandprofilearetheimportantqualityin dexesofrolledplateandstrip,andshapecontrolis thekeytechnologyforplateandstripmills.There searchonshapecontrolhasanimportantsignificance forpresettingcontrolofshapeandcrownandthede velopmentofrollingtechnology.The… 相似文献
12.
13.
14.
15.
16.
Three-Dimensional Model for Strip Hot Rolling 总被引:3,自引:0,他引:3
ZHANG Guo-min XIAO Hong WANG Chun-hua 《钢铁研究学报(英文版)》2006,13(1):23-26
Steel stripis widely usedin many fields such asautomobile ,building,transportation and householdappliance ,etc·. Withthei mprovement in productiv-ity and automation of strip processing,the require-ments for crown and flatness of strip have been in-creasingly severe ,and“crown free”steel strips arerequired for some special applications such as for au-tomobile parts andtinplate cans .In order toi mprovethe strip quality , an effective three-di mensionalmodel is needful to further study on the… 相似文献
17.
HU Yu GONG Dian-yao JIANG Zheng-yi XU Jian-zhong ZHANG Dian-hua LIU Xiang-hua 《钢铁研究学报(英文版)》2009,16(5)
Based on the influence coefficient method, the effect of entry strip crown on the shape of hot rolled strip was analyzed using the software of roll elastic deformation simulation. According to the practical condition of a domestic hot roiled strip plant, the unit strip crown change from the first stand to the last stand was calculated when the entry crown of hot strip varies. The calculated result shows that the entry strip crown does not significantly affect the target strip crown at the exit of the last finishing stand in respect to a fixed strip shape control reference (such as bending force). The calculation was analyzed, and the research is helpful in modeling strip shape setup and shape control. 相似文献
18.
HU Yu GONG Dian-yao 《钢铁研究学报(英文版)》2009,16(5):32-34
Based on influence coefficient method, using the software of roll elastic deformation simulation, the effect of entry crown on hot rolled strip shape was researched and analyzed. According to the real condition of certain domestic hot rolled strip factory, the unit crown change from the first stand to the last was calculated when entry crown of hot strip alters. The calculation result shows that the entry crown effect not obviously on the target strip crown at the exit of last stand with the strip shape control reference such as bending force keeping fixed. The reason of calculation was analyzed, the research work refers theory support to strip shape setup modeling and shape control. 相似文献