Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718

This paper presents the results of an experimental investigation on the wear mechanisms of uncoated tungsten carbide (WC) and coated tools (single-layer (TiAlN) PVD, and triple-layer (TiCN/Al₂O₃/TiN) CVD) in oblique finish turning of Inconel 718. Tool wear rate and wear mechanisms were evaluated for cutting speeds, 50<V<100 m/min, and feed rates, 0.075<f<0.125 mm/rev, at a constant depth of cut of 0.25 mm. It was concluded that abrasive and adhesive wear were the most dominant wear mechanisms, controlling the deterioration and final failure of the WC tools. While the triple layer CVD coated tools exhibited the highest wear resistance at high cutting speeds and low feeds, uncoated tools outperformed the single and multi-layer coated tools in the low range of cutting speeds and intermediate feeds. The cutting tool with single-layer PVD coating outperformed the other tools at the medium cutting speed.     

Wear of Ceramic Cutting Tools in Ni-Based Superalloy Machining

The machining performance of monolithic and composite silicon nitride and Al₂O₃-based cutting tools in continuous turning of Inconel 718 was examined. The character of tool wear has been found to vary, depending on the feed rate and cutting speeds. At a lower cutting speed, of 120 m/min, tool life is restricted by depth-of-cut notching, while at high cutting speeds (300 m/min), tools fail due to nose wear and fracture. The sensitivity of monolithic Si₃N₄ and Al₂O₃ to depth-of-cut notching was found to he significantly reduced with the addition of SiC whiskers, and to a lesser extent with TiC particulates. The ceramic composites also exhibited resistance to nose and flank wear that was higher than that of the monoliths. The internal stress distribution for the cutting tool has been calculated using the finite element method and is the basis for explaining fracture beneath the rake face. Cutting tool wear results are discussed in terms of chemical and mechanical properties of the ceramic tool material, abrasive wear, thermal shock resistance, and metal cutting conditions.     

Physical properties and cutting performance of silicon nitride ceramic

Silicon nitride, a nitrogen compound of highly covalent bond character, has low density, high hardness, low thermal expansion and high thermal conductivity and excellent oxidation and corrosion resistance. Therefore it is considered to be a promising material for high temperature engineering components.However, it has very poor sinterability compared with the conventional oxide ceramics owing to its low self-diffusivity. By investigating starting materials, sintering additives and processing, a hot-pressed silicon nitride ceramic having grains enveloped by crystalline boundary phases can be produced.The silicon-nitride-based ceramic has high strength, high Weibull modulus, fracture toughness and thermal conductivity, and low thermal expansion compared with existing cutting tool ceramics such as Al₂O₃ + TiC, and it is expected to have superior thermal shock resistance.This new ceramic cutting tool shows superior performance in cutting cast irons at high speeds (10–16.75 m s^?1 (600–1000 m min^?1)) and rates (about 1.0 mm rev^?1), where conventional tools cannot be used.     

Wear mechanisms of PcBN cutting tools when dry turning ASTM Grade 2 austempered ductile iron under finishing conditions

Experimental studies of dry finish turning of ASTM Grade 2 austempered ductile iron with PcBN cutting tools were carried out at cutting speeds ranging from 50 to 800 m/min, at a feed of 0.05 mm/rev and depth cut of 0.2 mm. The wear mechanisms of PcBN cutting tools were investigated through the examination of the wear surfaces by means of optical, scanning electron and transmission electron microscopes as well as energy dispersive spectroscopy. Flank wear and crater wear were the main wear modes within this range of cutting speeds. Adhesion and adhesion induced abrasion were the main wear mechanisms at cutting speeds less than 150 m/min. Abrasion and wear by thermally activated-diffusion and oxidation-chemical reaction wear were the main wear mechanisms at cutting speeds greater than 150 m/min. A high concentration of Mg, Si, and O on the wear surfaces and a heat-affected zone in the tools suggested that at speeds in excess of 150 m/min, the rate controlling wear mechanism involved chemical reaction between the tools and the operating environment.     

Finish Machining of Nickel-Base Inconel 718 Alloy with Coated Carbide Tool under Conventional and High-Pressure Coolant Supplies

Single-point turning of Inconel 718 alloy with commercially available Physical Vapour Deposition (PVD)-coated carbide tools under conventional and high-pressure coolant supplies up to 20.3 MPa was carried out. Tool life, surface roughness (Ra), tool wear, and component forces were recorded and analyzed. The test results show that acceptable surface finish and improved tool life can be achieved when machining Inconel 718 with high coolant pressures. The highest improvement in tool life (349%) was achieved when machining with 11 MPa coolant supply pressure at higher speed conditions of 60 m · min^?1. Machining with coolant pressures in excess of 11 MPa at cutting speeds up to 40 m · min^?1 lowered tool life more than when machining under conventional coolant flow at a feed rate of 0.1 mm · rev^?1. This suggests that there is a critical coolant pressure under which the cutting tools performed better under high-pressure coolant supplies.

Cutting forces increased with increasing cutting speed due probably to reactive forces introduced by the high-pressure coolant jet. Tool wear/wear rate increased gradually with prolonged machining with high coolant pressures due to improved coolant access to the cutting interface, hence lowering cutting temperature. Nose wear was the dominant tool failure mode when machining with coated carbide tools due probably to a reduction in the chip-tool and tool-workpiece contact length/area.     

A study of the cutting-induced heating effect on the machined surface in ultra-precision raster milling of 6061 Al alloy

Ti-6Al-4V alloy is an attractive material in many industries due to its unique and excellent combination of strength to weight ratio and their resistance to corrosion. However, because of its low thermal conductivity and high chemical reactivity, Ti-6Al-4V alloy is generally classified as a difficult-to-cut material that can be characterized by low productivity and rapid tool wear rate even at conventional cutting speeds. It is well known that tool wear has a strong relationship with the cutting forces and a sound knowledge about correlation between cutting forces variation and tool wear propagation is vital to monitor and optimize the automatic manufacturing process. In the present study, high-speed end-milling of Ti-6Al-4V alloy with uncoated cemented tungsten carbide tools under dry cutting conditions is experimentally investigated. The main objective of this work is to analyze the tool wear and the cutting forces variation during high-speed end-milling Ti-6Al-4V alloy. The experimental results show that the major tool wear mechanisms in high-speed end-milling Ti-6Al-4V alloy with uncoated cemented tungsten carbide tools are adhesion and diffusion at the crater wear along with adhesion and abrasion at the flank wear. The cutting force component in the negative y-direction is more dominant of the three components and displays significantly higher magnitudes than that of the other two components in x- and z-directions. The variation of cutting force component F _y has a positive correlation with the tool wear propagation, which can be used as a tool wear indicator during automatic manufacturing process.     

Wear mechanism of ceramic tools

Cutting tests were performed using ceramic cutting tools under continuous cutting conditions. The tests were carried out on AISI 1040 steel, with cutting speeds ranging from 5 to 11 m s⁻¹. The wear mechanism was investigated for both crater and flank. Alumina-toughened zirconia of submicron grain size showed the best wear resistance. Alumina with TiC, TiN and ZrO₂ inclusions exhibited a wear resistance a little lower than the above-mentioned materials. Low chemical stability seems to be the reason for the poor performances of the silicon carbide whiskers-reinforced alumina, silicon nitride and the tungsten carbide inserts.     

Performance of graded nano-composite ceramic tools in ultra-high-speed milling of Inconel 718

The cutting performance, failure types, and mechanisms of the graded nano-composite ceramic tools were investigated during dry face milling of Inconel 718. In these tests, round ceramic inserts were used at cutting speeds ranging from 500 to 1,100 m/min. The structures of the chips, cutting forces, and surface roughness were also examined. Failure surfaces of the tools were characterized by scanning electron microscopy. The results showed that the graded tool possessed a self-sharpening characteristic and exhibited higher cutting performance compared with the homogeneous ones, as a result of its enhanced mechanical properties, higher abrasive wear, and fracture resistance. The failure mechanisms of the tools involved chipping, flaking, notch wear, abrasive wear, and adhesive wear. The mechanisms responsible for the higher cutting performance of the graded tools were inferred to be the formation of compressive residual stress in the surface layer induced by the graded compositional structure.     

Wear behaviour of alumina based ceramic cutting tools on machining steels

The advanced ceramic cutting tools have very good wear resistance, high refractoriness, good mechanical strength and hot hardness. Alumina based ceramic cutting tools have very high abrasion resistance and hot hardness. Chemically they are more stable than high-speed steels and carbides, thus having less tendency to adhere to metals during machining and less tendency to form built-up edge. This results in good surface finish and dimensional accuracy in machining steels. In this paper wear behaviour of alumina based ceramic cutting tools is investigated. The machining tests were conducted using SiC whisker reinforced alumina ceramic cutting tool and Ti[C,N] mixed alumina ceramic cutting tool on martensitic stainless steel-grade 410 and EN 24 steel work pieces. Flank wear in Ti[C,N] mixed alumina ceramic cutting tool is lower than that of the SiC whisker reinforced alumina cutting tool. SiC whisker reinforced alumina cutting tool exhibits poor crater wear resistance while machining. Notch wear in SiC whisker reinforced alumina cutting tool is lower than that of the Ti[C,N] mixed alumina ceramic cutting tool. The flank wear, crater wear and notch wear are higher on machining martensitic stainless steel than on machining hardened steel. In summary Ti[C,N] mixed alumina cutting tool performs better than SiC whisker reinforced alumina cutting tool on machining martensitic stainless steel.     

Wear and Tribological Performance of Different Ceramic Tools in Dry High Speed Machining of Ni-Co-Cr Precipitation Hardenable Aerospace Superalloy

Tool wear is an important machinability criterion. To reduce total machining costs, this study demonstrates the wear and tribological performance of four ceramic tools in dry high-speed turning of Ni-Co-Cr precipitation hardenable superalloy (Inconel 100). Wear of the tool materials and the structural and phase transformations at the tool–chip interface were investigated. Results obtained reveal that SiAlON ceramic outperformed other ceramic tool materials at different cutting speeds due to the formation of a large amount of mullite tribofilms on the tool face, which serve as a thermal barrier layer. Alumina ceramic with the addition of ZrO₂ can be recommended for machining Inconel 100 at speeds above 150 m/min due to its ability to form thermal barrier ZrO₂ tribofilms, which decrease the coefficient of friction at the tool–chip interface. Mixed alumina and an alumina matrix reinforced with SiC_w were found to be unsuitable for machining age-hardened Inconel 100 superalloy.     

Wear mechanisms and residual stresses in alumina-based laminated cutting tools

The outstanding performances of the Al₂O₃ cutting tools in terms of potential cutting speed can lead to substantial economies in the machining of metallic materials.Nevertheless, their widespread use is limited by some drawbacks such as the tendency to edge chipping and to the propagation of microcracks, which can lead to premature failures.These shortcomings are due to the intrinsic low toughness of the ceramic material, which is in turn related to its characteristics non-metallic bonds.A well-recognised method of increasing the toughness of brittle materials is the introduction of surface compressive stresses, which can be obtained through a suitable lamination geometry of the tools as consequence of the different coefficients of thermal expansion (CTE) of the constituent layers.The performances of an alumina/zirconia laminated cutting tool used for machining steel have been investigated and compared to those of a non-laminated commercial alumina/zirconia cutting tool. The different wear mechanisms are explained on the basis of the different microstructures and chemical compositions. We have shown that residual compressive stresses, measured by Piezo-Spectroscopy, are effective in avoiding the microchipping on the flank zone but cannot avoid larger fractures caused by the residual porosity.     

Cutting performance of Si<Subscript>3</Subscript>N<Subscript>4</Subscript>/TiC micro-nanocomposite ceramic tool in dry machining of hardened steel

A type of Si₃N₄/TiC micro-nanocomposite ceramic cutting tool material was fabricated using Si₃N₄ micro-matrix with Si₃N₄ and TiC nanoparticles. Cutting performance of the Si₃N₄/TiC ceramic cutting tool in dry cutting of hardened steel was investigated in comparison with a commercial Sialon insert. Hard turning experiments were carried out at three different cutting speeds, namely 97, 114, and 156 m/min. Feed rate (f) and depth of cut (a _p) were fixed at 0.1 mm/rev and 0.2 mm, respectively. Results showed that cutting temperature increased rapidly to nearly 1000 °C with increasing cutting speed. The two types of cutting tools featured similar wear behavior. However, the Si₃N₄/TiC micro-nanocomposite ceramic cutting tool exhibited better wear resistance than the Sialon tool. Morphologies of crater and flank wear were observed with a scanning electron microscope. Results indicated that wear variation of the two types of ceramic cutting tools differed in the same conditions. Wear of the Si₃N₄/TiC micro-nanocomposite ceramic cutting tool is mainly dominated by abrasion and adhesion, whereas that of the Sialon ceramic cutting tool is dominated by abrasion, adhesion, thermal shock cracking, and flaking.     

Some observations on two-body abrasive wear

Pin-on-disc-type two-body abrasion tests were carried out on five metals with seven particle sizes over a range of loads, lengths of travel and sliding speeds. The familiar results that two-body abrasive wear is proportional to load and to distance travelled were confirmed. The “size effect”, in which particles below about 100 μm produce progressively less wear, was shown to be independent of load, sliding speed and prior cold working. Increasing the sliding speed from 1 to about 100 mm s^?1 produced an increase in wear resistance of about 50% for AISI 1020 steel. An increase in velocity above 100 mm s^?1 had little effect on the wear resistance. Plots of the wear resistance against the hardness of the annealed metal showed significant deviations from the linear relationship reported in the literature. The result is influenced by both sliding velocity and particle size.     

Comparative study on tool life and wear resistance of titanium nitride (TiN) and aluminium chromium nitride (AlCrN) coated carbide inserts

Abstract

The objective of this study is to investigate the enhancement of tool life and wear resistance with a physical vapour deposition (PVD) process applied using aluminium chromium nitride (AlCrN) and titanium nitride (TiN) coating on carbide inserts. Flank wear experiments are carried out on a computer numerically controlled (CNC) machine under wet conditions with both the coated inserts. Effectiveness of the coating on the tool life and its resistance to flank wear are observed at various cutting parameters such as cutting speed and feed rate by following the principle of design of experiments (DOE). It is inferred that AlCrN coated carbide tools perform nearly 70% better than the TiN coated carbide tools under high cutting speed and feed rate. AlCrN coating also enhances the durability of tool for metal cutting and thereby improves tool life even under harsh cutting conditions. A response surface methodology (RSM) is utilised to arrive at the optimum value for the various parameters which are responsible for improving the wear resistance and tool life.     

An Investigation of the Wear Mechanisms of Polycrystalline Cubic Boron Nitride (PCBN) Tools when End Milling Hardened Steels at Low/Medium Cutting Speeds

The commercial availability of PCBN tools has created the possibility for great improvements in the area of machining hardened steels. Roughing and finishing cuts can be carried out to achieve a surface finish as good as that obtained by grinding. Through this procedure, fabrication time can be greatly reduced and quality increased. This work presents a study of the wear of PCBN and cemented carbide tools when end milling hardened steels at low/medium cutting speeds. The experiments were carried out using a 12.0 mm diameter end milling tool with an indexable insert tipped with PCBN. Removal rate was 384 mm 3 min −1 . Carbide inserts were also tested under the same cutting conditions. The tests were carried out in the dry condition. Three different hardened steels were cut and the wear mechanism was investigated using a scanning electronic microscope (SEM). The minimal wear mechanism found was a combination of adhesion and abrasion. The wear occurred predominantly on the flank face, although some indications of crater wear were also detected. The amount of wear was significantly smaller for PCBN tools than for cemented carbide tools.     

Development and machinability evaluation of MgO doped Y-ZTA ceramic inserts for high-speed machining of steel

ABSTRACT

In current high productivity manufacturing era, it is necessary to develop non-conventional newer tool materials. Here, an attempt has been made for developing MgO doped zirconia-toughened alumina (Mg-ZTA) using powder metallurgy process route. The 3 mol% yttria stabilized zirconia (YSZ) (10 wt%), alumina (Al₂O₃) (90 wt%) with varying percentage of magnesium oxide (MgO) (0–1 wt%) are mixed to study the phase transformation and uniaxially pressed into square inserts with 0.8 mm nose radius and sintered at 1,600ºC for 1 h in pressure less condition. The maximum hardness of 17.04 GPa, fracture toughness of 5.09 MPa m^1/2 and flexural strength of 502 MPa, respectively, has been reached at 0.6 wt% of MgO due to more metastable tetragonal phase. The performance of the insert has been evaluated by machining AISI 4340 steel (radius 75 mm) in lathe. The performance with respect to flank wear, cutting force and surface roughness is quite impressive at different cutting speed even after 20 min of machining. It can be inferred that MgO doped ZTA insert can be used for medium to high-speed machining in current manufacturing scenario and is very promising to replace carbide or coated carbide inserts in coming days.     

Effects of Coating Materials on the Machinability of a Nickel Base,C-263, Alloy

PVD coated (TiN/TiCN/TiN, TiAIN and TiZrN) and uncoated carbide tools were used to machine a nickel base, C-263, alloy at high-speed conditions. The test results show that the multiple TiN/TiCN/TiN coated inserts gave the best overall performance in terms of tool life when machining at cutting speeds up to 68 m min and at depths of cut of 0.635 mm, 1.25 mm and 2.54 mm. All the tool grades tested gave fairly uniform surface roughness (Ra) values, below the rejection criterion, at lower speed conditions. The TiZrN coated inserts gave the lowest component forces when machining at lower cutting speed conditions while the TiA/N coated inserts gave the lowest component forces when machining at a higher speed of 68 m min^?1 and depth of cut of 1.25 mm. This tool performance can generally be attributed to the difference in their ability to provide effective lubrication at the cutting zone, thermal conductivity of the coating materials as well as the cutting conditions employed. The uncoated carbide tools generally encountered more severe crater wear, chipping/fracture of the cutting edges as well as pronounced notching during machining. This is due to their inability to provide effective lubrication at the cutting zone, thus impeding the gliding motion of the chips along the rake and flank faces respectively, thus accelerating flank wear. Analysis of the worn tool edges revealed adhesion of a compact “fin-shaped” structure of hardened burrs with saw-tooth like edges. This generally alters the initial geometry of the cutting edge, consequently resulting to poor surface finish with prolonged machining.     

Machinability issues in turning of Al-SiC (10p) metal matrix composites

The paper presents the results of an experimental investigation on the machinability of fabricated aluminum metal matrix composite (A356/SiC/10p) during continuous turning of composite rods using medium grade polycrystalline diamond (PCD 1500) inserts. MMC’s are very difficult to machine and PCD tools are considered by far, the best choice for the machining of these materials. Experiments were conducted at LMW-CNC-LAL-2 production lathe using PCD 1500 grade insert at various cutting conditions and parameters such as surface roughness, specific power consumed, and tool wear were measured. Machining was continued till the flank wear land on the tool crossed 0.4 mm. The influences of cutting speed on the insert wear and built-up edges (BUEs) formation were studied. The present results reaffirm the suitability of PCD for machining MMCs. Though BUE formation was observed at low cutting speeds, at high cutting speeds very good surface finish and low specific power consumption could be achieved.     

Evaluation on Effectiveness of CVD and PVD Coated Tools during Dry Machining of Incoloy 825

With wide applications of nickel-based superalloys in strategic fields, it has become increasingly necessary to evaluate the performance of different advanced cutting tools for machining such alloys. With a view to recommend a suitable cutting tool, the present work investigated various machinability characteristics of Incoloy 825 using an uncoated tool, chemical vapor deposition (CVD) of a bilayer of TiCN/Al₂O₃, and physical vapor deposition (PVD) of alternate layers of TiAlN/TiN-coated tools under varying machining conditions. The influence of cutting speed (51, 84, and 124 m/min) as well as feed (0.08, 0.14, and 0.2 mm/rev) was comparatively evaluated on surface roughness, cutting temperature, cutting force, coefficient of friction, chip thickness, and tool wear using different cutting tools. Although the CVD-coated tool was not useful in decreasing surface roughness and temperature, a significant reduction in cutting force and tool wear could be achieved with the same coated tool under a high cutting speed of 124 m/min. On the other hand, the PVD-coated tool outperformed the other tools in terms of machinability characteristics. This might be attributed to the excellent antifriction and antisticking property of TiN and good toughness due to the multilayer configuration in combination with a thermally resistant TiAlN phase. Adhesion, abrasion, edge chipping, and nose wear were the prominent wear mechanisms of the uncoated tool, followed by the CVD-coated tool. However, remarkable resistance to such wear was evident with the PVD TiAlN/TiN multilayer-coated tool.     

Evaluation of the Machinability of Nickel-Base,Inconel 718, Alloy with Nano-Ceramic Cutting Tools

The machinability of difficult-to-cut aerospace alloys can be enhanced by the rapid development of cutting tool materials that can withstand machining at high-speed conditions. The performance of nano-grain size ceramic tool materials were evaluated when machining nickel base, Inconel 718, in terms of tool life, tool failure modes and wear mechanisms as well as component forces generated under different roughing conditions. Comparison tests were carried out with commercially available ceramic tool materials of micron-grain composition.

The test results show that the micron grain size commercially available tool materials generally gave the longest tool life. The dominant failure mode is nose wear, while some of the nano-ceramic tools were rejected mainly due to chipping at the cutting edge. This suggests that physical properties and mechanical stability of the cutting edge of the ceramic tools influence their overall performance. It is also evident that chemical compositions of the tool materials played a significant role in their failure. The alumina base ceramics are more susceptible to premature fracture than the silicon nitride base ceramics with higher fracture toughness.