A study of removal of Pb heavy metal ions from aqueous solution using lignite and a new cheap adsorbent (lignite washing plant tailings)

The present study determines the efficiency with which lignite and lignite washing plant tailings can adsorb Pb heavy metal ions. In the first experiment, the effect of size distribution on the absorbance capacity was investigated for the samples. Therefore, lignite sample was ground to five sizes (d₈₀ = 0.600, 0.355, 0.250, 0.106 and 0.063 mm) under nitrogen (N₂), and the tailings sample was classified into seven fractions, along with the original state (original state: d₆₀ = 0.063, −1 + 0.600, −0.600 + 0.355, −0.355 + 0.250, −0.250 + 0.106, −0.106 + 0.063 and −0.063 mm). The test results showed that the optimum size distributions for lignite and tailings were d₈₀ = 0.063 mm and the original state (d₆₀ = 0.063 mm), respectively. Simultaneously, the adsorption capacity results of the two optimum sizes were compared with each other, and the tailings sample (d₆₀ = 0.063 mm) gave the best results, with 9.30 mg/g Pb ions adsorbed value. Therefore, in the second study, a series of laboratory experiments using 2³ full factorial designs was conducted to determine the optimum pH, contact time and initial metal concentration using the original tailings sample. The experimental studies showed that pH 9, a 120 min contact time and 300 ppm initial metal concentration gave the best results, namely an adsorption of 29.92 mg Pb ions/g.     

Cationic conjugated polyelectrolyte-based fluorometric detection of copper(II) ions in aqueous solution

A series of water-soluble cationic polyfluorene copolymer containing 2,2′-bipyridine moieties (PFP-P_1-3) in the backbone were designed and synthesized as the fluorescent probes for Cu²⁺ ions. In the absence of the Cu²⁺ ion, the PFP-P₂ exhibits strong fluorescence emission in aqueous solution. Upon adding the Cu²⁺ ion, the PFP-P₂ coordinates to Cu²⁺ ions through weak N?Cu interactions, and its fluorescence is efficiently quenched by the Cu²⁺ ion with a Stern-Volmer constant (K_sv) of 1.44 × 10⁷ M⁻¹. The new method has high sensitivity with a detection limit of 20 nM. The minor interference from other heavy metal ions clearly shows that the PFP-P₂ can be used as the Cu²⁺ ion probe with good selectivity.     

Microbial desulphurization of coal containing pyritic sulphur in a continuously operated bench scale coal slurry reactor

Pre-combustion microbial desulphurization of coal containing total sulphur (3.90%) and pyritic sulphur (2.80%) has been evaluated in a coal slurry reactor. The coal slurry reactor operated at hydraulic retention time (HRT) of 96 h with a coal pulp density of 15 percent and remove 79 percent of pyritic sulphur and 76 percent of ash with an increase in the calorific value of coal from 4400 to 6800 kcal kg⁻¹ at a pyritic load of 1.9 kg pyritic sulphur kg⁻¹ MLSS d⁻¹. The treated coal yield is 72 percent. The biochemical kinetic coefficients, viz. yield coefficient (Y) and decay coefficient (K_d) in the coal slurry reactor system are 0.178 and 0.007 d⁻¹, respectively, while maximum growth rate (μ_max) and half saturation rate constant (K_s) are 0.025 h⁻¹ and 0.220 g l⁻¹ as pyrite, respectively.     

Rhodamine-based fluorescent sensor for mercury in buffer solution and living cells

A novel fluorescent sensor based on thiooxorhodamine B has been prepared to detect Hg²⁺ in aqueous buffer solution. It demonstrates high selectivity for sensing Hg²⁺ with about 383-fold enhancement in fluorescence emission intensity and micromolar sensitivity (K_d = 7.5 × 10⁻⁶ mol L⁻¹) in comparison with alkali and alkaline earth metal ions (K⁺, Na⁺, Mg²⁺, Ca²⁺) and other transition metal ions (Mn²⁺, Ni²⁺, Co²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Ag⁺, Pb²⁺, Cr³⁺, Fe³⁺). Meanwhile the distinct color changes and rapid switch-on fluorescence also provide ‘naked eyes’ detection for Hg²⁺ over a broad pH range. Moreover, such sensor is cell-permeable and can visualize the changes of intracellular mercury ions in living cells using fluorescence microscopy.     

Electrochemical study on the selective formation of [Pb(cyclodextrin)]surface inclusion complexes at the carbon paste electrode/ClO4 1 M interphase

The formation constants of surface inclusion complexes were determined using a carbon paste electrode, CPE, and cyclic voltammetry for aqueous-based media containing Pb(II) and α, β and γ cyclodextrins. In order to promote the occupation of the molecular cavities in the cyclodextrins, the medium with the support electrolyte contained ClO₄⁻ ions, which have the capacity to modify the hydrophobic properties of such cavities. The results obtained were: Pb(II)-α_CDK = 883.7 ± 13.6 M⁻¹, Pb(II)-β_CDK = 727.5 ± 20.2 M⁻¹, Pb(II)-γ_CDK = 782 ± 10.7 M⁻¹.     

Preparation and characterisation of a poly(acrylamidoglycolic acid-co-acrylamide) hydrogel for selective binding of Cu and application to diffusive gradients in thin films measurements

A poly(acrylamidoglycolic acid-co-acrylamide) [poly(AAGA-co-AAm)] hydrogel was prepared by copolymerising 2-acrylamidoglycolic acid (AAGA) with acrylamide (AAm). The copolymer hydrogel composition and structure was characterised by FTIR spectroscopy and elemental microanalysis and found to contain 3.5 AAGA monomer units for each AAm monomer unit. This was similar to the monomer ratios used in the synthesis. The metal ion binding properties of the hydrogel were characterised for a range of metal ions (Cu²⁺, Cd²⁺, K⁺, Na⁺, Mg²⁺ and Ca²⁺) under varying conditions of pH, ionic strength, metal concentration and time. The hydrogel was shown to bind Cu²⁺ and Cd²⁺ strongly under non-competitive binding conditions, with binding capacities of 5.3 and 5.1 μmol cm⁻², respectively. The binding capacity of each metal decreased, under competitive binding conditions (with a range of metal ions present at 17.8 μN), to 1.3 and 0.17 μmol cm⁻², respectively, indicating stronger selectivity for Cu²⁺. The metal ions were readily recovered (>94%) by eluting with 2 M nitric acid solution for 24 h. The binding capacities for Cu²⁺ and Cd²⁺ were also found to decrease with increasing ionic strength and at pH values <5. The copolymer was found to have an equilibrium swelling ratio (q_w) of over 500 at a maxima of pH 5.4 and at low ionic strengths. Finally, the copolymer hydrogel was tested as a binding phase with the diffusive gradients in thin films technique. A linear mass vs. time relationship was observed for Cu²⁺ in synthetic Windermere water with a recovery of approximately 100%.     

Novel chemosensory materials based on polyfluorenes with 2-(2′-pyridyl)-benzimidazole and 5-methyl-3-(pyridin-2-yl)-1,2,4-triazole groups in the side chain

Polyfluorenes with 2-(2′-pyridyl)-benzimidazole (P1, P2 and P4) and 5-methyl-3-(pyridin-2-yl)-1,2,4-triazole (P3) groups in the side chain were synthesized by Suzuki polycondensation. The responsive properties of polymers on metal ions and H⁺ were investigated by absorption and emission spectra. The fluorescences of polymers (P1-P4) were completely quenched upon the transition metal ions such as Co²⁺, Ni²⁺, Fe³⁺ and Ag⁺ due to the enhanced electronic communication properties of conjugated polymers. The obvious differences to Ni²⁺ ion responsive sensitivity were observed between P1 and P4 polymers. The fluorescences of P1 and P4 were quenched to 50 (I₀/I) and to 22 (I₀/I) upon the addition of a Ni²⁺ solution of 3.2 × 10⁻⁶ M, as well as 5.0 × 10⁻⁶ M, respectively, owing to the different conjugated backbone. The fluorescences of P2 and P3 were completely and hardly quenched upon the addition of a Al³⁺ solution of 1.0 × 10⁻⁴ M, respectively, owing to the different receptors in the side chain. P2 showed good selectivity to Ni²⁺ ion in the range of quencher concentration as low as 5 ppm, owing to the different chelating abilities of receptor with ions. Cu²⁺ and Mn²⁺ ions hardly quenched the fluorescences of polymers (P1-P4), which were different from the oligopyridyl-functionalized conjugated polymers. The results further opened the opportunities to develop the tailored sensory materials through the appropriate alteration of receptors in the side chain and the conjugated backbone.     

A novel graphite-polyurethane composite electrode modified with thiol-organofunctionalized silica for the determination of copper ions in ethanol fuel

A graphite-polyurethane composite modified with 2-benzothiazolethiol organofunctionalized silica was evaluated as an alternative electrode in the determination of Cu²⁺ ions in ethanol fuel samples, on the basis of a differential pulse anodic stripping voltammetry procedure. This metal can be quantified by mixing ethanol fuel with 0.10 mol L⁻¹ KNO₃ aqueous solution and subsequent voltammetric measurement after the accumulation step. A maximum limit of 70% (v/v) ethanol in potassium nitrate aqueous solution was obtained for voltammetric measurements without loss of sensitivity for metal species. Factors affecting the pre-concentration and stripping steps were investigated and optimum conditions were employed to develop the analytical procedure. Using 20 min of accumulation time, the linear range of 0.1-1.2 μmol L⁻¹ was obtained with the limit of detection of 3.9 × 10⁻⁸ mol L⁻¹. The developed electrode was successfully applied to determine Cu²⁺ in commercial ethanol fuel samples. The proposed method was compared with a traditional analytical technique, the flame atomic absorption spectrometry, and no significant differences between the results obtained by both methods were observed according to statistical evaluation.     

Synthesis and characterization of electrically conducting poly-o-methoxyaniline Zr(1V) molybdate Cd(II) selective composite cation-exchanger

In this study a composite cation-exchanger poly-o-methoxyaniline Zr(1V) molybdate was prepared and the ion-exchange properties like ion-exchange capacity for different metal ions, elution behavior, pH titration and a temperature dependent study of ion-exchange capacity were explored. The physical properties of the material were also determined using TGA-DTA, FTIR, X-ray and SEM studies. The results of physical properties were found progressive in terms of their specific properties. Electrical conductivity of this composite determined by four-in-line probe method was found to be in semi-conducting range i.e. 10^− 4-10^− 2 S cm^− 1. The adsorption efficiency towards heavy metal ions was determined by distribution studies and material was found highly selective for cadmium a heavy toxic metal ion indicating the utility for the removal from waste stream.     

Effect of zwitterionic salt on the electrochemical properties of a solid polymer electrolyte with high temperature stability for lithium ion batteries

In this study, we prepare a kind of solid polymer electrolyte (SPE) based on N-ethyl-N′-methyl imidazolium tetrafluoroborate (EMIBF₄), LiBF₄ and poly(vinylidene difluoride-co-hexafluoropropylene) [P(VdF-HFP)] copolymer. The resultant SPE displays high thermal stability above 300 °C and high room temperature ionic conductivity near to 10⁻³ S cm⁻¹. Its electrochemical properties are improved with incorporation of a zwitterionic salt 1-(1-methyl-3-imidazolium)propane-3-sulfonate (MIm3S). When the SPE contains 1.0 wt% of the MIm3S, it has a high ionic conductivity of 1.57 × 10⁻³ S cm⁻¹ at room temperature, the maximum lithium ions transference number of 0.36 and the minimum apparent activation energy for ions transportation of 30.9 kJ mol⁻¹. The charge-discharge performance of a Li₄Ti₅O₁₂/SPE/LiCoO₂ cell indicates the potential application of the as-prepared SPE in lithium ion batteries.     

Aluminium (III)-selective PVC membrane sensor based on a Schiff base complex of N,N′-bis (salicylidene)-1, 2-cyclohexanediamine

A potentiometric aluminium sensor, based on the use N,N′-bis(salicylidene)-1,2-cyclohexanediamine (NBSC) as a neutral carrier, in poly(vinyl chloride) (PVC) matrix, is reported. Effect of various plasticizers; 2-nitrophenyloctylether (o-NPOE), tri-n-butyl phosphates (TBP), dioctylpththalate (DOP) & chloronapthalen (CN), and anion excluder, sodium tetraphenylborate (NaTPB) was studied. The best performance was obtained with a membrane composition of PVC: o-NPOE: NBSC: NaTPB ratio (w/w; mg) of 150:150:5:5. The sensor exhibits significantly enhanced selectivity toward Al³⁺ ions over the concentration range 1.0 × 10⁻⁸-1.0 × 10⁻¹ M with a lower detection limit of 5.0 × 10⁻⁹ M and a Nernstian slope of 20.3 ± 0.1 mV decade⁻¹ of activity. Influence of the membrane composition and possible interfering ions was investigated on the response properties of the electrode. Fast and stable response, good reproducibility and long-term stability are demonstrated. The sensor shows response time of <5 s and can be used for about 3 months without any considerable divergence in their potential response. Selectivity coefficients determined by matched potential method (MPM) indicate high selectivity for aluminium (III) ion. The proposed electrode shows fairly good discrimination of aluminium (III) from many metal ions. It was successfully applied for direct determination of aluminium (III) in biological, industrial and environmental samples. The electrode can be used in the pH range of 2.0-9.0 and mixtures containing up to 20% (v/v) non-aqueous content. It was used as an indicator electrode in potentiometric titration of aluminium ion vs. EDTA.     

Use of novel permeable membrane and air cathodes in acetate microbial fuel cells

In the existing microbial fuel cells (MFCs), the use of platinized electrodes and Nafion^® as proton exchange membrane (PEM) leads to high costs leading to a burden for wastewater treatment. In the present study, two different novel electrode materials are reported which can replace conventional platinized electrodes and can be used as very efficient oxygen reducing cathodes. Further, a novel membrane which can be used as an ion permeable membrane (Zirfon^®) can replace Nafion^® as the membrane of choice in MFCs. The above mentioned gas porous electrodes were first tested in an electrochemical half cell configuration for their ability to reduce oxygen and later in a full MFC set up. It was observed that these non-platinized air electrodes perform very well in the presence of acetate under MFC conditions (pH 7, room temperature) for oxygen reduction. Current densities of −0.43 mA cm⁻² for a non-platinized graphite electrode and −0.6 mA cm⁻² for a non-platinized activated charcoal electrode at −200 mV vs. Ag/AgCl of applied potential were obtained. The proposed ion permeable membrane, Zirfon^® was tested for its oxygen mass transfer coefficient, K₀ which was compared with Nafion^®. The K₀ for Zirfon^® was calculated as 1.9 × 10⁻³ cm s⁻¹.     

LaBaCuFeO5+δ-Ce0.8Sm0.2O1.9 as composite cathode for solid oxide fuel cells

The performance of the LaBaCuFeO_5+δ-Ce_0.8Sm_0.2O_1.9 (LBCF-SDC) composite cathodes was studied in this paper. Electrical conductivity, thermal expansion and electrochemical properties were investigated by four probing DC technique, dilatometry, AC impedance and polarization techniques, respectively. The thermal expansion coefficients of the LBCF-SDC were between (16.3 and 13.4) × 10⁻⁶ K⁻¹ from 30 to 850 °C, which was lower value than LBCF (17.0 × 10⁻⁶ K⁻¹). AC Impedance spectroscopy measurements of LBCF-SDC/SDC/LBCF-SDC test cell were carried out. Polarization resistance values for the LBCF-SDC10 cathode was as low as 0.097 Ω cm² at 750 °C.     

Poly(o-aminophenol) film prepared in the presence of sodium dodecyl sulfate: Application for nickel ion dispersion and the electrocatalytic oxidation of methanol and ethylene glycol

Poly(o-aminophenol) (POAP) was formed by successive cyclic voltammetry in monomer solution in the presence of sodium dodecyl sulfate (SDS) on the surface of a carbon paste electrode. The electrochemical behavior of the SDS-POAP carbon paste electrode has been investigated by cyclic voltammetry in 0.5 M HClO₄ and 5 mM K₄[Fe(CN)₆]/0.1 M KCl solutions as the supporting electrolyte and model system, respectively. Ni(II) ions were incorporated into the electrode by immersion of the polymeric modified electrode having amine groups in 0.1 M Ni(II) ion solution. Cyclic voltammetric and chronoamperometric experiments were used for the electrochemical study of this modified electrode. A good redox behavior of the Ni(III)/Ni(II) couple at the surface of electrode can be observed. The electrocatalytic oxidations of methanol and ethylene glycol (EG) at the surface of the Ni/SDS-POAP electrode were studied in a 0.1 M NaOH solution. Compared to bare carbon paste and POAP-modified carbon paste electrodes, the SDS-POAP electrode significantly enhanced the catalytic efficiency of Ni ions for methanol oxidation. Finally, using a chronoamperometric method, the catalytic rate constants (k) for methanol and ethylene glycol were found to be 2.04 × 10⁵ and 1.05 × 10⁷ cm³ mol⁻¹ s⁻¹, respectively.     

Transport of cobalt(II) through a hollow fiber supported liquid membrane containing di-(2-ethylhexyl) phosphoric acid (D2EHPA) as the carrier

This work presents experimental, modeling and simulation studies for Co²⁺ ion extraction using hollow fiber supported liquid membrane (HFSLM) operated in a recycling mode. Extractant di-(2-ethylhexyl) phosphoric acid (D2EHPA) diluted with kerosene has been used as the membrane phase. The Co²⁺ ion concentration in the aqueous feed phase was varied in the range of 1–3 mM. Also, D2EHPA concentration was varied in the range of 10–30% (v/v). A mass transfer model has been developed considering the complexation and de-complexation reactions to be fast and at equilibrium. Equations for extractant mass balance and counter-ion (H⁺) transport have also been incorporated in the model. Extraction equilibrium constant (K_ex) for cobalt–D2EHPA system has been estimated from equilibration experiments and found to be 3.48 × 10⁻⁶. It was observed that the model results are in good agreement with the experimental data when diffusivity of metal-complex (D_m) through the membrane phase is 1.5 × 10⁻¹⁰ m²/s. Feed phase pH and strip phase acidity had negligible effect on the extraction profiles of Co²⁺ ions. An increase in D2EHPA concentration increased extraction rates of Co²⁺ ions. The membrane phase diffusion step was found to be the controlling resistance to mass transfer.     

Determination of picomolar silver concentrations by differential pulse anodic stripping voltammetry at a carbon paste electrode modified with phenylthiourea-functionalized high ordered nanoporous silica gel

This study introduces the design of an anodic stripping voltammetric (ASV) method for the silver ion determination at a carbon paste electrode (CPE), chemically modified with phenylthiourea-nanoporous silica gel (Tu-SBA-15-CPE). The electroanalytical pro includes two steps: preconcentration of metal ions at an electrode surface, followed by quantification of the accumulated species by differential pulse anodic stripping voltammetric methods. Factors affecting the performance of the anodic stripping were investigated, including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The most sensitive and reliable electrode contained 10% Tu-SBA-15 and 90% carbon paste. The accumulation potential and time were set at, −200 mV and 300 s, respectively, and the scan rate at 50 mV s⁻¹ in the scan range of −200 to 700 mV. The resulting electrode demonstrated a linear response over range of silver ion concentration of 8.0-80 pmol/L with detection limit (S/N = 3) of 5 pmol/L. The prepared electrodes were used for the silver determination in sea and tap water samples and very good recovery results were obtained. The accuracy was assessed through recovery experiments and independent analysis by graphite furnace atomic absorption spectrometry.     

Spectroscopic and structural studies of di-ureasils doped with lithium perchlorate

Di-urea cross-linked POE/siloxane hybrid ormolytes (di-ureasils) doped with a wide concentration range of lithium perchlorate trihydrate (LiClO₄·3H₂O) (200 ≥ n ≥ 0.5, where n expresses the salt content in terms of the number of ether oxygen atoms per Li⁺ ion) have been analysed by Fourier transform infrared and Raman (FT-IR and FT-Raman, respectively) spectroscopies and X-ray diffraction (XRD). The results obtained lead us to conclude that the xerogels with n ≥ 5 are totally amorphous. At n ≤ 1 free salt is observed. “Free” ClO₄⁻ ions appear to be the main charge carriers at the conductivity maximum located within the 25 ≤ n ≤ 8 composition range of this family of ormolytes. At n = 15 ClO₄⁻ ions coordinated in mono/tridentate (C_3v symmetry) and bidentate (C_2v symmetry) configurations were detected. In salt-rich samples with n < 15 there is a marked tendency for ionic association. The resulting decrease that occurs in the concentration of “free” ions is consistent with the observed significant decrease of the ionic conductivity. The analysis of the “amide I” and “amide II” regions provided solid proof that the Li⁺ ions bond to the urea carbonyl oxygen atoms over the entire range of salt concentration studied.     

Direct electrochemistry and electrocatalysis of cytochrome c based on chitosan-room temperature ionic liquid-carbon nanotubes composite

A robust and effective composite film combined the benefits of room temperature ionic liquid (RTIL), chitosan (Chi) and multi-wall carbon nanotubes (MWNTs) was prepared. Cytochrome c (Cyt c) was successfully immobilized on glassy carbon electrode (GCE) surface by entrapping in the composite film. Direct electrochemistry and electrocatalysis of immobilized Cyt c were investigated in detail. A pair of well-defined and quasi-reversible redox peaks of Cyt c was obtained in 0.1 mol L⁻¹ pH 7.0 phosphate buffer solution (PBS), indicating the Chi-RTIL-MWNTs film showed an obvious promotion for the direct electron transfer between Cyt c and the underlying electrode. The immobilized Cyt c exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis current was linear to H₂O₂ concentration in the range of 2.0 × 10⁻⁶ to 2.6 × 10⁻⁴ mol L⁻¹, with a detection limit of 8.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The apparent Michaelis-Menten constant (K_m) was calculated to be 0.45 ± 0.02 mmol L⁻¹. Moreover, the modified electrode displayed a rapid response (5 s) to H₂O₂, and possessed good stability and reproducibility. Based on the composite film, a third-generation reagentless biosensor could be constructed for the determination of H₂O₂.     

Use of a selective extractant-impregnated resin for removal of Pb(II) ion from waters and wastewaters: Kinetics,equilibrium and thermodynamic study

Adsorption of Pb(II) ion by a novel extractant-impregnated resin, EIR, was studied as a function of various experimental parameters using batch adsorption experiments. The new EIR was prepared by impregnating gallocyanine (GCN) onto Amberlite XAD-16 resin beads. The EIR was characterized by nitrogen analysis and SEM micrographs. The new EIR showed excellent selectivity factor values (α) for Pb(II) adsorption respect to other metal ions. The effects of some chemical and physical variables were evaluated and the optimum conditions were found for Pb(II) removal from aqueous solutions. The equilibrium adsorption isotherm was fitted with the Langmuir adsorption model. The maximum adsorption capacity (q_max) of EIR for Pb(II) ions was found to be 367.92 mg g⁻¹. The kinetic studies showed that the intra-particle diffusion is the rate-controlling step. Also, the intra-particle diffusion coefficients, D_ip values, were of the order of 10⁻¹² m² s⁻¹. The values of enthalpy (ΔH°) were positive, which confirms the endothermic nature of adsorption process. Also, the positive entropy changes (ΔS°) were showed that the randomness increased along with the adsorption process. In addition, the obtained negative values of Gibbs free energy (ΔG°) indicated feasible and spontaneous nature of the adsorption process at different temperatures. The new adsorbent was very stable so that it can be successfully used for many consecutive cycles without significant loss in its adsorption capacity.     

Double channel electrode flow cell application to the study of HO2 production on MnxCo3−xO4 (0 ≤ x ≤ 1) spinel films

We conducted a study on the electroreduction of O₂ in alkaline solution at room temperature on pure thin oxide electrodes of composition Mn_xCo_3−xO₄ (0 ≤ x ≤ 1) using the double channel electrode flow cell (DCEFC). The oxides were prepared at 150 °C and deposited by spray pyrolysis onto titanium substrates. The oxygen reduction reaction (orr) occurs through “interactive” and “parallel” pathways, and the ratio of O₂ molecules reduced to OH⁻ ions with respect to those reduced to HO₂⁻ ions depends on the oxide stoichiometry and on the applied overpotential. The formation of HO₂⁻ increases when the manganese concentration increases. The results obtained for the orr show that the number of electrons transferred per O₂ molecule decreases from 3 to 2 and the ratio k₁/k₂ (the rate constants for direct reduction to OH⁻ and indirect reduction to HO₂⁻) increases, respectively, in the overpotential studied range (−0.05 to −0.6 V). The Mn³⁺ ions placed in the B-sites of the spinel structure seem to be the active centres, where hydrogen peroxide is formed.