Controlling micro‐ and nanofibrillar morphology of polymer blends in low‐speed melt spinning process. Part II: Influences of extrusion rate on morphological changes of a PLA/PVA blend through a capillary die

The effects of the extrusion rate on the morphological changes of poly(lactic acid) (PLA)/poly(vinyl alcohol) (PVA) blend through a capillary die were investigated. In this study, the extrusion rate or mass flow rate is altered from 0.5 g min^?1 to 2 g min^?1 with an increment of 0.5 g min^?1. The PLA/PVA blend with a composition of 30/70 (wt %) exhibits a particle matrix morphology with dispersed PLA droplets within the PVA matrix. It is found that, the spherical or ellipsoidal dispersed PLA droplets are elongated and coalesced into rod‐like or longer ellipsoidal droplets when they pass through the capillary die. When the extrusion rate increases, the coalescence between the large PLA droplets occurs more intense. However, the changes of the extrusion rate have no strong effect on the coalescence of small droplets having diameter less than about 150 nm. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44257.     

Design of highly tough poly(l‐lactide)‐based ternary blends for automotive applications

Technical renewable poly(l ‐lactide) (PLA)‐based blends represent an elegant way to achieve attractive properties for engineering applications. Recently, the miscibility between PLA and poly(methyl methacrylate) (PMMA) gave rise to new formulations with enhanced thermo‐mechanical properties but their high brittleness still remains a challenge to be overcome. This work here focuses on rubber‐toughened PLA/PMMA formulations for injection‐molding processes upon the addition of a commercially available ethylene‐acrylate impact modifier (BS). The miscibility between PLA and PMMA is not altered by the presence of BS but the incorporation of BS (17% by weight) into a PLA/PMMA matrix could enhance both ductility and toughness of PLA/PMMA blends for PMMA content up to 50 wt %. An optimum range of particle sizes (d_n ～0.5 µm) of the dispersed domains for high impact toughness is identified. These bio‐based ternary blends appear as promising alternatives to petro‐sourced blends such as ABS‐based blends in engineering injection‐molding parts. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43402.     

Morphology and properties of the biosourced poly(lactic acid)/poly(ethylene oxide‐b‐amide‐12) blends

Biosourced poly(lactic acid) (PLA) blends with different content of poly(ethylene oxide‐b‐amide‐12) (PEBA) were prepared by melt compounding. The miscibility, phase structure, crystallization behavior, mechanical properties, and toughening mechanism were investigated. The blend was an immiscible system with the PEBA domains evenly dispersed in the PLA matrix. The PEBA component suppressed the nonisothermal melt crystallization of PLA. With the addition of PEBA, marked improvement in toughness of PLA was achieved. The maximum for elongation at break and impact strength of the blend reached the level of 346% and 60.5 kJ/m², respectively. The phase morphology evolution in the PLA/PEBA blends after tensile and impact tests was investigated, and the corresponding toughening mechanism was discussed. It was found that the PLA matrix demonstrates obvious shear yielding in the blend during the tensile and impact tests, which induced energy dissipation and therefore lead to improvement in toughness of the PLA/PEBA blends. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

Rubber‐toughened PLA blends with low thermal expansion

In this study, poly (lactic acid) (PLA) blended with various rubber components, i.e., poly (ethylene‐glycidyl methacrylate) (EGMA), maleic anhydride grafted poly(styrene‐ethylene/butylene‐styrene) triblock elastomer (m‐SEBS), and poly(ethylene‐co‐octene) (EOR), was investigated. It was observed that EGMA is highly compatible due to its reaction with PLA. m‐SEBS is less compatible with PLA and EOR is incompatible with PLA. Electron microscopy (SEM and TEM) revealed that a fine co‐continuous microlayer structure is formed in the injection‐molded PLA/EGMA blends. This leads to polymer blends with high toughness and very low linear thermal expansion both in the flow direction and in the transverse direction. The microlayer thickness of rubber in PLA blends was found to play key roles in reducing the linear thermal expansion and achieving high toughness of the blends. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A comparative study of poly(l‐lactide)‐block‐poly(ϵ‐caprolactone) six‐armed star diblock copolymers and polylactide/poly(ϵ‐caprolactone) blends

This paper deals with the synthesis of a series of six‐armed star diblock copolymers based on poly(l ‐lactide) (PLLA) and poly(?‐caprolactone) (PCL) by ring‐opening polymerization using stannous octoate as catalyst and the preparation of polylactide (PLA)/PCL linear blends using a solution blending technique, while keeping the PLA‐to‐PCL ratio comparable in both systems. The thermal, rheological and mechanical properties of the copolymers and the blends were comparatively studied. The melting point and the degree of crystallinity were found to be lower for the copolymers than the blends due to poor folding property of star copolymers. Dynamic rheology revealed that the star polymers have lower elastic modulus, storage modulus and viscosity as compared to the corresponding blends with similar composition. The blends show two‐phase dispersed morphology whereas the copolymers exhibited microphase separated morphology with elongated (worm‐like) microdomains. The crystalline structures of the copolymers were characterized by larger crystallites than their blend counterparts, as estimated using Sherrer's equation based on wide‐angle X‐ray diffraction data. © 2016 Society of Chemical Industry     

Tailoring the morphology and properties of poly(lactic acid)/poly(ethylene)‐co‐(vinyl acetate)/starch blends via reactive compatibilization

Poly(lactic acid)/poly(ethylene‐co‐vinyl acetate)/starch (PLA/EVA/starch) ternary blends were prepared by multi‐step melt processing (reactive extrusion) in the presence of maleic anhydride (MA), benzoyl peroxide and glycerol. The effects of MA and glycerol concentration on the morphology and properties of the PLA/EVA/starch blends were studied using scanning electron microscopy, transmission electron microscopy, atomic force microscopy, the Molau experiment, dynamic mechanical thermal analysis and differential scanning calorimetry etc. The plasticization and compatibilization provided a synergistic effect to these blends accompanied by a significant reduction in starch particle size and an increase in interfacial adhesion. Starch was finely dispersed in the ternary blends with a dimension of 0.5 ? 2 µm. Furthermore, EVA‐coated starch or a starch‐in‐EVA type of morphology was observed for the reactively compatibilized PLA/EVA/starch blends. The EVA with starch gradually changed into a co‐continuous phase with increasing MA concentration. Consequently, the toughness of the blends was improved. Since property stability of starch is an issue, the tensile properties of these blends were measured after different storage times and the blends showed good property stability. Copyright © 2012 Society of Chemical Industry     

Morphology development from rod-like to nanofibrillar structures of dispersed poly (lactic acid) phase in a binary blend with poly (vinyl alcohol) matrix along the spinline

The morphological evolution of thermoplastic poly (vinyl alcohol) (PVA) and poly (lactic acid) (PLA) blend filaments along the spinline is investigated for the first time. Emphasis of the study is given on considering the axial velocity gradient and tensile stress that influence the final state of deformation of the dispersed PLA phase. In this study, pieces of the PVA/PLA blend filaments at different locations along the spinline are collected by using a special self-constructed fiber-capturing device. This fiber-capturing device allows closer off-line study of the morphological properties of PVA/PLA blend filaments. The axial velocity gradient at different zones along the spinline is calculated from velocity data using Laser Doppler Velocimetry (LDV) technique. The tensile stress is determined from the momentum balance equation. It is observed that the fibrillation process takes place up to a certain distance from the die exit, where the polymeric PVA/PLA blend filament reaches its glass transition temperature. In this region, the axial velocity and tensile stress undergoes major changes. A phase inversion of dispersed PLA phase from rod-like structures to continuous long thin fibrils has been found at the point in which the axial velocity gradient reaches a maximum value.     

Compression molding and melt‐spinning of the blends of poly(lactic acid) and poly(butylene succinate‐co‐adipate)

Poly(lactic acid) (PLA) is a biobased polymer made from biomass having high mechanical properties for engineering materials applications. However, PLA has certain limited properties such as its brittleness and low heat distortion temperature. Thus, the aim of this study is to improve toughness of PLA by blending with poly(butylene succinate‐co‐adipate) (PBSA), the biodegradable polymer having high toughness. Polymer blends of PLA and PBSA were prepared using a twin screw extruder. The melt rheology and the thermal property of the blends were examined. Further the blends were fabricated into compression molded parts and melt‐spun fiber and were subjected to tensile and impact tests. When the PBSA content was low, PBSA phase was finely dispersed in the PLA matrix. On the other hand, when the PBSA content was high, this minor phase dispersed as a large droplet. Mechanical properties of the compression molded parts were affected by the dispersion state of PBSA minor component in PLA matrix. Impact strength of the compression molded parts was also improved by the addition of soft PBSA. The improvement was pronounced when the PBSA phase was finely dispersed in PLA matrix. However, the mechanical property of the blend fibers was affected by the postdrawing condition as well as the PBSA content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41856.     

Morphology and properties of biodegradable and biosourced polylactide blends with poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

Biodegradable polymer blends based on biosourced polymers, namely polylactide (PLA) and poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3HB‐co‐4HB)), were prepared by melt compounding. The effects of P(3HB‐co‐4HB) on the miscibility, phase morphology, thermal behavior, mechanical properties, and biodegradability of PLA/P(3HB‐co‐4HB) blends were investigated. The blend was an immiscible system with the P(3HB‐co‐4HB) domains evenly dispersed in the PLA matrix. However, the T_g of P(3HB‐co‐4HB) component in the blends decreased compared with neat P(3HB‐co‐4HB), which might be attributed to that the presence of the phase interface between PLA and P(3HB‐co‐4HB) resulted in enhanced chain mobility near interface. The addition of P(3HB‐co‐4HB) enhanced the cold crystallization of PLA in the blends due to the nucleation enhancement of PLA caused by the enhanced chain mobility near the phase interface between PLA and P(3HB‐co‐4HB) in the immiscible blends. With the increase in P(3HB‐co‐4HB) content, the blends showed decreased tensile strength and modulus; however, the elongation at beak was increased significantly, indicating that the inherent brittlement of PLA was improved by adding P(3HB‐co‐4HB). The interesting aspect was that the biodegradability of PLA is significantly enhanced after blends preparation. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Bio‐plastics and elastomers from polylactic acid/thermoplastic polyurethane blends

Blends of two biocompatible polymers: thermoplastic polyester‐urethane (TPU) and polylactic acid (PLA) were studied. The effect of the blending ratio on blend morphology and properties was examined by running a series of blends from 10 to 80 wt % of PLA. Increasing TPU concentration in the blends lowered the glass transition and melting point of PLA indicating that the components were compatible and partially miscible. The blends with 10–40 wt % PLA are hard, reinforced elastomers, while those with 60–80 wt % PLA are tough plastics. Cocontinuous morphology was suggested in samples with 40 and 50 wt % PLA. Inversion points between 30 and 40 wt % PLA (from globular phase is dispersed in the matrix to a cocontinuous morphology) and between 50 and 60 wt % PLA (a transition from cocontinuous to TPU dispersed in the PLA matrix) were observed. Elastomers with higher PLA content and intermediate morphology displayed a combination of high tensile strength, hardness, relatively high elongation and modulus. New materials have potential applications in the medical field. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41104.     

Mechanisms of plastic deformation in biodegradable polylactide/poly(1,4‐cis‐isoprene) blends

Polylactide (PLA), a main representative of biodegradable and made from renewable resources polymers, is surprisingly brittle at ambient temperature. In this article it is investigated how to increase its toughness by a strategy called “rubber toughening” using poly(1,4‐cis‐isoprene), a major component of natural rubber, which is immiscible with PLA, could be well dispersed in PLA matrix and is biodegradable. Immiscible blends of PLA with poly(1,4‐cis‐isoprene) were prepared by melt blending and their properties were studied and optimized. Incorporation of as low as 5 wt % of rubber increased the strain at break of compression molded film during uniaxial drawing, and also improved its tensile impact strength by 80%. The complex mechanism of plastic deformation in the blends leading to improvement of ductility and toughness was revealed. The rubbery particles initiated crazing at the early stages of deformation, as evidenced by transmission and scanning electron microscopy and also by small angle X‐ray scattering. Crazing was immediately followed by cavitation inside rubber particles, which further promoted shear yielding of PLA. The sequence of those mechanisms was proven by microscopic investigation. All three elementary mechanisms acting in the sequence indicated are responsible for surprisingly efficient toughening of PLA by a major component of natural rubber. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Epoxy‐tert‐butyl poly(cyanoarylene ether) blends: Phase morphology,fracture toughness,and mechanical properties

Tert‐butyl hydroquinone–based poly(cyanoarylene ether) (PENT) was synthesized by the nucleophilic aromatic substitution reaction of 2,6‐dichlorobenzonitrile with tert‐butyl hydroquinone using N‐methyl‐2‐pyrrolidone (NMP) as solvent in the presence of anhydrous potassium carbonate in a nitrogen atmosphere at 200°C. PENT‐toughened diglycidyl ether of bisphenol A epoxy resin (DGEBA) was developed using 4,4′‐diaminodiphenyl sulfone (DDS) as the curing agent. Scanning electron micrographs revealed that all blends had a two‐phase morphology. The morphology changed from dispersed PENT to a cocontinuous structure with an increase in PENT content in the blends from 5 to 15 phr. The viscoelastic properties of the blends were investigated using dynamic mechanical thermal analysis. The storage modulus of the blends was less than that of the unmodified resin, whereas the loss modulus of the blends was higher than that of the neat epoxy. The tensile strength of the blends improved slightly, whereas flexural strength remained the same as that of the unmodified resin. Fracture toughness was found to increase with an increase in PENT content in the blends. Toughening mechanisms like local plastic deformation of the matrix, crack path deflection, crack pinning, ductile tearing of thermoplastic, and particle bridging were evident from the scanning electron micrographs of failed specimens from the fracture toughness measurements. The thermal stability of the blends were comparable to that of the neat resin. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3536–3544, 2006     

Reactive compatibilization of high‐impact poly(lactic acid)/ethylene copolymer blends catalyzed by N,N‐dimethylstearylamine

The inherent brittleness of poly(lactic acid) (PLA) limits its wide application in many fields. Here, high‐impact PLA/ethylene–methyl acrylate–glycidyl methacrylate random terpolymer (EMA–GMA) blends were prepared with the addition of a small amount of N,N‐dimethylstearylamine (DMSA) catalyst. It was found that the notched impact resistance of various PLA/EMA–GMA blends could be considerably improved by adding DMSA. In particular, the notched Izod impact strength of the blend with 20 wt% EMA–GMA increased from 35.6 to 83.5 kJ m^?2 by adding 0.2 wt% DMSA. Reactive compatibilization between PLA and EMA–GMA with DMSA was studied using Fourier transform infrared spectroscopy. The results indicated that DMSA promoted the reaction between the epoxide group of EMA–GMA and end groups (–OH, –COOH) of PLA. This considerably improved the interfacial adhesion, leading to better wetting of the dispersed phase by the PLA matrix and finer dispersed EMA–GMA particles. Therefore, the significant increase in notched impact strength was attributed to the effective reactive compatibilization promoted by DMSA. © 2013 Society of Chemical Industry     

In situ compatibilization of polylactide/thermoplastic polyester elastomer blends using a multifunctional epoxide compound as a processing agent

In situ compatibilized poly(lactic acid)/thermoplastic polyester elastomer (PLA/TPEE) (80/20) blends are prepared by using multifunctional epoxide oligomer (coded as ADR) as a reactive modifier. Experiments such as torque, melt mass flow rate (MFR), SEM, DSC and tensile test were conducted to characterize properties of the PLA/TPEE/ADR blends. In situ reactions between PLA, TPEE and ADR were researched using a lab torque rheometer. It was proposed that ADR may initiate a variety of chain extension/branching reactions between PLA and TPEE under mixing process. In particular, the formed copolymer PLA‐ADR‐TPEE could be viewed as an in situ compatibilizer to improve the compatibility of PLA and TPEE. As expected, the value of MFR decreased greatly with increasing the ADR addition. The morphology reveals that interface adhesion of PLA/TPEE blend was enhanced with the incorporation of ADR, which led to a reduction in TPEE domain size. Moreover, tensile ductility of PLA/TPEE (80/20) blend was improved greatly by addition of the reactive modifier, e.g. the elongation at break was increased from 53% to the maximum value of 213% with addition of 1.2 phr ADR. The toughening effect can be explained by crazing with shear yielding mechanism. Attempts were made to produce ductile films from these PLA/TPEE/ADR blends by using extrusion blowing method. Effect of ADR on blowing stability and tensile property of these blends was investigated. Improvement on blowing stability and tensile ductility of PLA/TPEE/ADR films also shows that ADR is an efficiently reactive compatibilizer, as well as a viscosity enhancer for PLA/TPEE blends. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43424.     

Preparation of high toughness and high transparency polylactide blends resin based on multiarmed polycaprolactone‐block‐poly(l‐lactide)

Modification of poly(l ‐lactide) (PLLA) via blending with two or more polymers is one of the effective approaches used to overcome the brittleness of PLLA, which often requires the addition of a compatibilizer and generate opaque materials. To solve this problem, multiarmed polycaprolactone‐block‐PLLA (PCL‐b‐PLLA) was synthesized by consecutive ring‐opening polymerization of ε‐caprolactone and l ‐lactide using multihydroxyl alcohols as initiator. The structure and composition was confirmed by proton nuclear magnetic resonance and gel permeation chromatography. PLLA/multiarmed PCL‐b‐PLLA blends with various blend ratios were prepared via melt mixing. The presence of multiarmed PCL‐b‐PLLA (30%) in the PLLA matrix exhibited more than 80 times improvement in the elongation at break, as compared to unmodified PLLA. The addition of multiarmed PCL‐b‐PLLA in the PLLA contributed to the enhancement of the storage modulus in the low frequency, which was related to the entanglement of the PLLA and multiarmed PCL‐b‐PLLA. The blend interface had no obvious phase separation, and showed good adhesion between dispersed block copolymer phases within the continuous PLLA phase. The compatibilization mechanism and toughing mechanism were proposed. The resulting PLLA blends also showed good transparency. The current research opened a new route available to prepare transparent PLA‐based resin with enhanced properties. POLYM. ENG. SCI., 56:1125–1137, 2016. © 2016 Society of Plastics Engineers     

Interfacial compatibility of super‐tough poly(lactic acid)/polyurethane blends investigated by positron annihilation lifetime spectroscopy

Supertough polylactide (PLA)/polyurethane (PU) blends were prepared by reactive blending of PLA with polyester polyol and toluene‐2,4‐diisocyanate. The free volume and interfacial compatibility between the two polymers were investigated by positron annihilation lifetime spectroscopy. The PU particles dispersed homogeneously in the PLA matrix and self‐assembled into a subinclusion microstructure, resulting in fibrils and significant plastic deformation occurs during impact process. More phase interface and free volume cavities formed between PLA and PU boundary because of a good interfacial compatibility between the two polymers, leading to smaller sizes of free volume cavities, and the increasing of the number of these cavities. Therefore, the toughness of PLA was greatly improved by blending PU. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46596.     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

Crystallization behavior of fully biodegradable poly(lactic acid)/poly(butylene adipate‐co‐terephthalate) blends

Both poly(lactic acid) (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) are fully biodegradable polyesters. The disadvantages of poor mechanical properties of PLA limit its wide application. Fully biodegradable polymer blends were prepared by blending PLA with PBAT. Crystallization behavior of neat and blended PLA was investigated by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and wide angle X‐ray diffraction (WAXD). Experiment results indicated that in comparison with neat PLA, the degree of crystallinity of PLA in various blends all markedly was increased, and the crystallization mechanism almost did not change. The equilibrium melting point of PLA initially decreased with the increase of PBAT content and then increased when PBAT content in the blends was 60 wt % compared to neat PLA. In the case of the isothermal crystallization of neat PLA and its blends at the temperature range of 123–142°C, neat PLA and its blends exhibited bell shape curves for the growth rates, and the maximum crystallization rate of neat PLA and its blends all depended on crystallization temperature and their component. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on the thermal and mechanical behavior of PLA‐PET blends

The increasing use of bio‐sourced and biodegradable polymers such as poly(lactic acid) (PLA) in bottle packaging presents an increasing challenge to the polyethylene terephthalate (PET) recycling process. Despite advanced separation technologies to remove PLA from PET recyclate, PLA may still be found in rPET process streams. This study explores the effects of PLA on the mechanical properties and crystallization behavior of blends of PET containing 0.5–20% PLA produced by injection molding. SEM indicates an immiscible blend of the two polymers and TGA confirms the independent behavior of the two polymers under thermal degradation conditions. Temperature‐modulated DSC studies indicate that adding PLA to PET increases the rigid amorphous fraction of the PET moiety. Critical amounts of PLA induce stress oscillation behavior during mechanical testing. The mechanical behavior of the samples is explained by antagonistic interaction between increased rigid amorphous fraction and decreased fracture strength arising from an increased population of PLA microparticles. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44147.     

Investigation of structure and mechanical properties of toughened poly(l‐lactide)/thermoplastic poly(ester urethane) blends

In this study, poly(l ‐lactide) (PLA) is melt‐blended with thermoplastic polyurethane (TPU) to modify the brittleness of PLA. An aliphatic ester‐based TPU was selected in order to have an ester sensitivity for degradation and an inherent biocompatibility. Using this compatible TPU, there was no need to apply problematic compatibilizers, so the main positive properties of PLA such as biocompatibility and degradability were not challenged. The detected microstructure of PLA/TPU blends showed that when the TPU content was lower than 25 wt %, the structure appeared as sea‐islands, but when the TPU content was increased, the morphology was converted to a cocontinuous microstructure. A higher interfacial surface area in the blend with 25 wt % TPU (PLA25) resulted in a higher toughness and abrasion resistance. The various analyses confirmed interactions and successful coupling of two phases and confirmed that melt‐blending of PLA with the aliphatic ester‐based TPU is a convenient, cost‐effective, and efficient method to conquer the brittleness of PLA. The prepared blends are general‐purpose plastics, but PLA25 showed an optimum mechanical strength, toughness, and biocompatibility suitable for a wide range of applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43104.