Correlation Between Adsorption/Desorption of Surfactant and Change in Friction of Stainless Steel in Aqueous Solutions Under Different Electrode Potentials

Adsorption of sodium dodecyl sulfate (SDS) surfactant on the surface of gold or graphite in aqueous solutions has received extensive attention in the past. However, few studies have been done on the adsorption/desorption of SDS surfactant at surfaces of engineering materials as well as on their influence on friction behavior. In this article, quartz crystal microbalance (QCM), electrochemical spectroscopy, atomic force microscopy (AFM), lateral force microscopy (LFM), and ball-on-disc friction test have been jointly used to investigate the effects of electrode potential on adsorption and desorption of SDS surfactant, surfactant aggregate morphology on stainless steel surfaces, nanoscale and macroscale tribological behavior in dilute SDS aqueous solutions. Experiment results have shown that DS⁻ anions adsorb on the surface of the stainless steel electrode and form stripe-shaped aggregates at the open circuit potential (+0.03 V vs. SCE), which corresponds to a low friction coefficient. Under the negative potential of −0.4 V versus SCE, the adsorbed aggregates of DS⁻ anions are removed from the stainless steel surface, resulting in a high friction coefficient. By adjusting the electrode potential of stainless steel, both of the surfactant adsorption and tribological property can be controlled in a significant range.     

Compositional dependence of the microscopic frictional properties of single crystal metal carbides

The frictional properties of TiC(100), Ti_0.3V_0.6C(100), and VC(100) surfaces in contact with a silicon nitride probe tip have been investigated by atomic force microscopy (AFM) under ambient pressures of dry nitrogen as well as environments of different relative humidities. Calibration of normal and lateral force has permitted the determination of the quantitative frictional properties of the three carbide samples on a nanometer length scale. In these studies, TiC(100) exhibits the lowest friction coefficient, ranging from ∼0.044 to ∼0.082 under the different environments. VC(100) and Ti_0.3V_0.6C(100) have similar friction coefficients (∼0.07) under dry nitrogen conditions, yet VC exhibits a larger friction coefficient (∼0.158) than Ti_0.3V_0.6C (∼0.129) under conditions of higher relative humidity (∼55%). Condensation of water vapor with increasing relative humidity results in an increase in the frictional response for all the three samples. The experimental results demonstrate that the frictional properties of the three carbide samples are correlated to their surface composition and surface free energy.     

Speed and Atmosphere Influences on Nanotribological Properties of NbSe<Subscript>2</Subscript>

Nanotribological properties of NbSe₂ are studied using an atomic friction force microscope. The friction force is measured as a function of normal load and scan speeds ranging from 10 nm s⁻¹ to 40 μm s⁻¹ under two atmospheres (air and argon). At low speed, no effect of atmosphere is noticed and a linear relationship between the friction and normal forces is observed leading to a friction coefficient close to 0.02 for both atmospheres. At high speed, the tip/surface contact obeys the JKR theory and the tribological properties are atmosphere dependent: the shear stress measured in air environment is three times lower than the one measured under argon atmosphere. A special attention is paid to interpret these results through numerical data obtained from a simple athermal model based on Tomlinson approach.     

Effects of Deposition Conditions and Counter Bodies on the Tribological Properties of Pulsed DC Magnetron Sputtered TiN–MoS<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Composite Coating

In the current study, TiN–MoS _x composite coatings were deposited by co-sputtering of MoS₂ and Ti targets under a mixture of Ar and N₂ gas environment using pulsed DC closed-field unbalanced magnetron sputtering. The tribological response of TiN–MoS _x composite coatings was studied against two different counter bodies: cemented carbide (WC–6% Co) ball and pin made of aluminium alloy (AlSiMg). First, the effect of substrate bias was studied on tribological properties using cemented carbide ball. Lowest coefficient of friction in the range of 0.03–0.04 was obtained for the specimen deposited at a substrate bias of −60 V. Wear coefficient was also found to be minimum for the same specimen. Coatings were further deposited at an optimum bias of −60 V in order to vary MoS _x content of TiN–MoS _x composite coating. Effect of variation of chemical composition of the coating was then studied on tribological performance of the coating against aluminium alloy counterface. Excellent anti-sticking property of MoS _x was found to have enabled the TiN–MoS _x composite coating to achieve considerably low coefficient of friction against aluminium alloy. It was shown that with optimum MoS _x content of TiN–MoS _x composite coating, it was possible to attain as low coefficient of friction as 0.09 against aluminium alloy even under normal atmospheric condition.     

Friction and Wear Properties of Silicon Carbide in Water from Different Sources

Low friction and low wear of SiC sliding against itself in water at room temperature have been well reported in the past 20 years, and some practical applications have been developed. However, the properties of friction and wear in pure, deionized or distilled water have been mainly observed and not in water from sources in nature. In this article, the fundamental properties of friction and wear between SiC ball and disk are observed in water from ground, river, and sea, and the results are compared with those in deionized water in the viewpoints of modes of lubrication and wear and the resultant values of friction coefficient and wear rate. The smallest friction coefficient (μ_ℓ = 0.005) in steady state is observed in deionized water and the largest (μ_ℓ = 0.013) in sea water. The smallest wear rate (w _s = 2.2 × 10⁻⁷ mm³/Nm) is observed in sea water and the largest (w _s = 3.1 × 10⁻⁷ mm³/Nm) in deionized water. The intermediate values of μ_ℓ and w _s between the smallest and the largest ones are observed in ground and river water. The modes of lubrication and wear, which generated observed values of μ_ℓ and w _s, are considered as mixed lubrication and tribochemical wear. The chemical elements of Na, Cl, Mg, and K in sea water observed on wear particles and pits are thought effective to generate the largest value of μ_ℓ and the smallest value of w _s.     

Tribological behaviors and mechanisms of Ti<Subscript>3</Subscript>AlC<Subscript>2</Subscript>

Tribological behaviors and the relevant mechanism of a highly pure polycrystalline bulk Ti₃AlC₂ sliding dryly against a low carbon steel disk were investigated. The tribological tests were carried out using a block-on-disk type high-speed friction tester, at the sliding speeds of 20–60 m/s under a normal pressure of 0.8 MPa. The results showed that the friction coefficient is as low as 0.1∼0.14 and the wear rate of Ti₃AlC₂ is only (2.3–2.5) × 10⁻⁶ mm³/Nm in the sliding speed range of 20–60 m/s. Such unusual friction and wear properties were confirmed to be dependant dominantly upon the presence of a frictional oxide film consisting of amorphous Ti, Al, and Fe oxides on the friction surfaces. The oxide film is in a fused state during the sliding friction at a fused temperature of 238–324 °C, so it takes a significant self-lubricating effect.     

Carbon Nanotube Reinforced Polyimide Thin-film for High Wear Durability

In this paper, the influence of single walled carbon nano tubes (SWCNTs) addition on the tribological properties of the polyimide (PI) films on silicon substrate was studied. PI films, with and without SWCNTs, were spin coated onto the Si surface. Coefficient of friction and wear durability were characterized using a ball-on-disk tribometer by employing a 4 mm diameter Si₃N₄ ball sliding against the film, at a contact pressure of ∼370 MPa, and a sliding velocity of 0.042 ms⁻¹. Water contact angle, AFM topography, and nano-indentation tests were conducted to study the physical and mechanical properties of the films. SWCNTs marginally increased the water contact angle of PI film. The addition of SWCNTs to PI has increased the hardness and elastic modulus of pristine PI films by 60–70%. The coefficient of friction of PI films increased slightly (∼20%) after the addition of SWCNTs, whereas, there was at least two-fold increase in the wear life of the film based on the film failure condition of coefficient of friction higher than 0.3. However, the film did not show any sign of wear even after 100,000 cycles of rotation indicating its robustness. This increase in the wear durability due to the addition of the SWCNTs is believed to be because of the improvement in the load-bearing capacity of the composite film and sliding induced microstructural changes of the composite film.     

Surface Energies of Magnetic Recording Head Components

The rate of material removal during fixed abrasive lapping is a function of friction coefficient, the surface tension of the lubricant and of the substrate, and the contact angles between the interfaces. In this study, the authors measured the surface energies of materials typically found in thin film magnetic recording heads using contact angle measurements and the Lifshitz–van der Waals acid/base approach. The different materials tested were Ni_xFe_y, Al₂O₃, and Al₂O₃-TiC. Sample preparation procedures were also considered. The chemical used to wash the surface was observed to affect the measured substrate surface energies. Surface energy values for samples washed with either acetone or hexane showed comparable results. The Ni_xFe_y gave the highest measured surface energy (46.3–48.8 mJ m⁻²) followed by Al₂O₃ (44.1–45.3 mJ m⁻²) and Al₂O₃-TiC (43.3–45.3 mJ m⁻²). In contrast, the oil-washed samples measured generally lower surface energy values. The study characterized the interaction of two lubricant types against the three materials. The oil-based lubricant spreads completely on oil-washed samples mainly because of the low surface tension of the oil (22.0 mJ m⁻²) and did not show measurable contact angles. In comparison, the water-soluble lubricant ethylene glycol, due to its higher surface tension (48.0 mJ m⁻²), formed higher contact angles ranging from 47.2 to 59.6° on the different substrates.     

Ultralow Friction Behaviors of Hydrogenated Fullerene-Like Carbon Films: Effect of Normal Load and Surface Tribochemistry

Friction and wear behaviors of hydrogenated fullerene-like (H-FLC) carbon films sliding against Si₃N₄ ceramic balls were performed at different contact loads from 1 to 20 N on a reciprocating sliding tribometer in air. It was found that the films exhibited non-Amontonian friction behaviors, the coefficient of friction (COF) decreased with normal contact load increasing: the COF was ~0.112 at 1 N contact load, and deceased to ultralow value (~0.009) at 20 N load. The main mechanism responsible for low friction and wear under varying contact pressure is governed by hydrogenated carbon transfer film that formed and resided at the sliding interfaces. In addition, the unique fullerene-like structures induce well elastic property of the H-FLC films (elastic recovery 78%), which benefits the high load tolerance and induces the low wear rate in air condition. For the film with an ultralow COF of 0.009 tested under 20 N load in air, time of flight secondary ion mass spectrometry (ToF-SIMS) signals collected inside and outside the wear tracks indicated the presence of C₂H₃ ⁻ and C₂H₅ ⁻ fragments after tribological tests on the H-FLC films surface. We think that the tribochemistry and elastic property of the H-FLC films is responsible for the observed friction behaviors, the high load tolerance, and chemical inertness of hydrogenated carbon-containing transfer films instead of the graphitization of transfer films is responsible for the steady-state low coefficients of friction, wear, and interfacial shear stress.     

Adhesive Wear Performance of T-OPRP and UT-OPRP Composites

In the current work, the effects of treating the oil palm fibres on the tribological performance of polyester composite were studied against polished stainless steel counterface using Block-on-Ring (BOR) technique under dry contact condition. Wear and friction characteristics of treated and untreated oil palm fibre reinforced polyester (T-OPRP and UT-OPRP) composites were evaluated at different sliding distances (0.85–5 km), sliding velocities (1.7–3.9 m/s) and applied loads (30–100 N). SEM observations were performed on the worn surfaces of the composites to examine the damage features. Specific wear rate (Ws), friction coefficient and interface temperature results were presented against the operating parameters. The results revealed that test parameters significantly influenced the wear performance of the composites. Both treated and untreated oil palm fibres enhanced the wear and frictional performance of polyester composites. T-OPRP showed less Ws by about 11% compared to UT-OPRP. This was due to the better interfacial adhesion offered by the treated fibres. The SEM observation made on UT-OPRP worn surface showed debonding and bending of fibres, and fragmentation and deformation on the resinous regions. Meanwhile, T-OPRP composite showed less damages compared to UT-OPRP, where no sign of fibres debonding was observed.     

Ni3Al Matrix Composite with Lubricious Tungstate at High Temperatures

Ni₃Al–Ag–BaF₂/CaF₂–W composites were fabricated by the powder metallurgy route, and their tribological properties over a wide temperature range, starting from room temperature up to 800 °C, were investigated. The Ni₃Al matrix composite with 15 wt% BaF₂/CaF₂ exhibited a favorable friction coefficient (range 0.3–0.4) and wear rate (0.2–6.2 × 10⁻⁴mm³ N⁻¹ m⁻¹). The formation of BaWO₄ and CaWO₄ with lubricity on the worn surface due to a tribo-chemical reaction at high temperatures provided excellent lubricating properties. The low friction coefficient over a broad temperature range could be attributed to the synergistic effect of Ag, BaF₂/CaF₂, BaWO₄, and CaWO₄.     

The effect of an alumina counterface on friction reduction of CuO/3Y-TZP composite at room temperature

The friction behavior of CuO/yttria-stabilized tetragonal zirconia (3Y-TZP) composite in dry sliding against alumina at room temperature has been investigated. The results show that an alumina counterface has a crucial role on the frictional behavior when sliding against CuO/3Y-TZP composite in comparison with other counter materials. Pure 3Y-TZP shows high friction and wear under the same conditions. It is found that the friction reduction behavior is dependent on the sliding test conditions such as load and humidity. A thin aluminum-rich layer less than 200 nm thick on the contact surface during the low friction situation has been found by various analyzing techniques including interference microscopy, micro-Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microcopy (SEM) and energy dispersive X-ray spectroscopy (EDX). The induced change of contact conditions and interfacial chemical reaction between CuO and alumina to form the phase CuAlO₂ increase the wear of alumina and accelerates the formation of an aluminum-rich surface layer. The presence of such a layer in the contact is beneficial for reducing friction. After a certain sliding distance, the coefficient of friction shifts from a low value to a high value due to a change in the dominating wear mechanism. This transition is shown to be caused by a different composition and thickness of the interfacial layer.     

Tribological Properties of Arc-Evaporated NbAlN Hard Coatings

Nb_1−x Al _x N hard coatings were synthesised by cathodic arc-evaporation with different Al contents to study its influence on the tribological properties. Ball-on-disc tests at temperatures up to 700 °C were performed and the recorded coefficient of friction was generally in the range from 0.8 to 1.0. Subsequent analysis of the coating wear track and the counterpart wear scar by optical profilometry and Raman spectroscopy revealed details on the wear behaviour of the tested coatings. The best wear performance for the Nb-rich coatings was in the temperature range of 300–500 °C, whereas at the maximum testing temperature the higher oxidation resistance with increasing Al content was beneficial in terms of wear resistance.     

Friction Study of a Ni Nanodot-patterned Surface

Nanoscale frictional behavior of a Ni nanodot-patterned surface (NDPS) was studied using a TriboIndenter by employing a diamond tip with a 1 μm nominal radius of curvature. The Ni NDPS was fabricated by thermal evaporation of Ni through a porous anodized aluminum oxide (AAO) template onto a Si substrate. Surface morphology and the deformation of the NDPS were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM), before and after friction/scratch testing. SEM images after scratching clearly showed that, similar to what was assumed at the macroscale, the frictional force is proportional to the real area of contact at the nanoscale. It was found that adhesion played a major role in the frictional performance, when the normal load was less than 20 μN and plastic deformation was the dominant contributor to the frictional force, when the normal load was between 60 μN and 125 μN. Surprisingly, a continuum contact mechanics model was found to be applicable to the nanoscale contact between the tip and the inhomogeneous Ni NDPS at low loads. The coefficient of friction (COF) was also found to depend on the size of the tip and was four times the COF between a 100 μm tip and the Ni NDPS. Finally, the critical shear strength of the Ni nanodots/Si substrate interface was estimated to be about 1.24 GPa.     

Effect of Tribofilm Formation on the Dry Sliding Friction and Wear Properties of Magnetron Sputtered TiAlCrYN Coatings

Nano-structured TiAlCrYN coatings, grown by unbalanced magnetron sputtering on various steel substrates, exhibited friction coefficients 0.6–0.8 and wear coefficients 10⁻¹⁶–10⁻¹⁵ m³ N⁻¹ m⁻¹ in dry sliding wear tests. This article reports comprehensive worn surface analyses using SEM, TEM, EDX, EELS and Raman spectroscopy. A ~80 nm thick tribofilm formed on the TiAlCrYN worn surface was found to have dense amorphous structure and homogeneous oxide composition of Cr_0.39Al_0.19Ti_0.20Y_0.01O_0.21. Viscous flow of the amorphous tribofilm was dominant in causing the high friction coefficient observed. The coatings showed combined wear mechanisms of tribo-oxidation and nano-scale delamination.     

Environmental effects on the friction of hydrogenated DLC films

We have investigated environmental effects on hydrogenated diamond-like carbon (H-DLC) films under various pressures of H₂O, O₂, and N₂ by ultrahigh vacuum (UHV) tribometry. The H-DLC film exhibits an ultralow coefficient of friction (μ = 0.004 in UHV). The μ value increases with increasing pressure of H₂O and O₂. Specifically, μ increases up to 0.07 under 10 Torr of H₂O, and up to 0.03 under 150 Torr of O₂; these are typical H₂O and O₂ contents respectively in ambient air. Our results are consistent with similar environmental effects previously reported. But, we have also discovered that these friction changes are reversible, returning to the ultralow value when UHV is restored. The reversibility of the friction behavior in both environments, coupled with the lack of evidence of tribochemical changes by Auger electron spectroscopy, suggest that the observed friction changes are due to the weakly adsorbed gas molecules that influence the friction property by physically separating the H-DLC interface. Speed-dependent tribometry also supports this argument. In addition, two DLC films with different hydrogen contents and with widely different friction coefficients in UHV are shown to exhibit identical μ values under humid environments, further demonstrating that the frictional properties of these DLC films are essentially determined by the surface layer of adsorbed gas molecules.     

Sliding friction and wear performance of Ti6Al4V in the presence of surface-capped copper nanoclusters lubricant

The friction and wear properties of Ti₆Al₄V sliding against AISI52100 steel ball under different lubricative media of surface-capped copper nanoclusters lubricant—Cu nanoparticles capped with O,O′-di-n-octyldithiophosphate (Cu-DTP), rapeseed oil and rapeseed oil containing 1 wt% Cu-DTP was evaluated using an Optimol SRV oscillating friction and wear tester. The wear mechanism was examined using scanning electron microscopy (SEM) and X-ray photoelectron spectrosmeter (XPS). Results indicate that Cu-DTP can act as the best lubricant for Ti₆Al₄V as compared with rapeseed oil and rapeseed oil containing 1 wt% Cu-DTP. The applied load and sliding frequency obviously affected the friction and wear behavior of Ti₆Al₄V under Cu-DTP lubricating. The frictional experiment of the Ti₆Al₄V sliding against AISI52100 cannot continue under the lubricating condition of rapeseed oil or rapeseed oil containing 1 wt% Cu-DTP when the applied load are over 100 N. Surprisingly, the frictional experiment of Ti₆Al₄V sliding against AISI52100 steel can continue at the applied load of 450 N under Cu-DTP lubricating. The tribochemical reaction film containing S and P is responsible for the good wear resistance and friction reduction of Ti₆Al₄V under Cu-DTP at the low applied load. However, a conjunct effect of Cu nanoparticle deposited film and tribochemical reaction film containing S and P contributes to the good tribological properties of Ti₆Al₄V under Cu-DTP at the high-applied load.     

Design of Low Wear Polymer Composites

Multifunctional tribological coatings rely on combinations of materials to improve properties, such as lubricity and wear resistance. For example, some polymer composites exhibit favorable tribological performance as solid lubricants. Here, classical molecular dynamics simulations are used to investigate the tribological behaviors of a mixed system of polyethylene (PE) sliding over polytetrafluoroethylene (PTFE) with the results compared with the sliding of the relevant homogeneous systems. In particular, oriented cross-linked PTFE and PE surfaces are slid in several relative sliding directions such that the surface chains are in-registry or out-of-registry and at various applied normal loads. The simulation results quantify the ways in which the mixed PTFE–PE system behaves differently than either of the homogeneous systems due to the lack of interlocking phases at the interface. These findings are compared with experimental production of polyetheretherketone (PEEK)–PTFE composites that have unusually low wear rates of 7.0 × 10⁻⁸ mm³/Nm, coupled with a steady, low friction coefficient of μ = 0.11 for over two million sliding cycles. The simulation results explain the atomic-scale origins of the frictional properties of this composite.     

NiAl Matrix High-Temperature Self-Lubricating Composite

A high-temperature self-lubricating composite NiAl–Cr–Mo–CaF₂ was fabricated using the powder metallurgy technique, and the tribological behavior of the composite at a wide range of temperatures (room temperature to 1000 °C) was investigated. The results showed that the composite had a favorable friction coefficient of about 0.2 and an excellent wear resistance of about 1 × 10⁻⁵ mm³N⁻¹m⁻¹ at the high temperatures tested (800 and 1000 °C). The excellent self-lubricating performance was attributed to the formation of the glaze film on the worn surface consisting mainly of CaCrO₄ and CaMoO₄ as high-temperature solid lubricants.     

Adhesive wear and frictional characteristics of UHMWPE and HDPE sliding against different counterfaces under dry contact condition

Abstract

The current work evaluates the wear and frictional performance of ultrahigh molecular weight polyethylene (UHMWPE) and high density polyethylene (HDPE) sliding against different metal counterfaces, stainless steel(SS), mild steel (MS) and aluminium (Al), under dry contact condition. The experiments were conducted using pin on disc machine at different sliding distances (0–40·32 km), 15 N applied load and 2·8 m s^–1 sliding velocity. Interface temperatures and frictional forces were measured simultaneously during the sliding, while specific wear rates were determined for every 1·68 km sliding distance. Based on the optical microscopy of the worn surface and wear track, frictional and wear results were analysed and discussed. The experimental results showed that the type of counterface material significantly influences both frictional and wear performances of the selected polymers. This was mainly due to the film transfer characteristics. Higher temperature and friction coefficient for UHMWPE and HDPE were evident when sliding took place against Al counterface. Sliding the polymers against stainless steel showed low friction coefficients compared to other counterfaces.