Visible light-induced photocatalytic activity of delafossite AgMO2 (M = Al, Ga, In) prepared via a hydrothermal method

Delafossite-structured oxides AgMO₂ (M = Al, Ga, In) were successfully synthesized using fluoro(ethylene-propylene) (FEP) pouch via a facile hydrothermal method. The obtained samples were characterized by X-ray diffraction (XRD), BET surface area measurement, UV–vis diffuse reflectance spectroscopy (DRS), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity of the as-prepared samples was evaluated by the degradation of rhodamine B (RhB) and methyl orange (MO) under visible light irradiation. All three samples showed photocatalytic activity for RhB and MO degradation under visible light irradiations and their photocatalytic activity followed the order of AgInO₂ > AgGaO₂ > AgAlO₂. The relative high photocatalytic activity of AgInO₂ can be attributed to its high quantity of the surface hydroxyl groups. The photocatalytic mechanism of AgInO₂ was proposed and its stability was also investigated.     

Photocatalytic properties of mesoporous TiO2 nanocomposites modified with carbon nanotubes and copper

The photocatalytic activity of mesoporous TiO₂ modified by the addition of carbon nanotubes (CNTs) and Cu is reported. Nanocomposites of carbon nanotubes (CNTs) containing varying amounts of Cu were formed by treatment with Cu²⁺ then reduced to Cu⁰ using NaBH₄ as the reducing agent. The mesoporous TiO₂, synthesized by a sol-gel method from titanium isopropoxide, was combined with the CNT/Cu nanocomposites to form the photocatalysts which were characterized by XRD, SEM, TEM, FTIR, XPS and BET surface area analysis. The photocatalytic properties of the mesoporous TiO₂ composites were studied by measuring the degradation of methyl orange (MO) which was optimal in the sample containing 20 wt% of the Cu-CNT nanocomposite. The degradation efficiency for MO was a synergistic effect of photo-degradation of TiO₂ and may be due to improvement of the electrical conductivity of the system by the presence of the CNT/Cu networks, since the photodegradation of MO and the photocatalytic activity of the photoactive systems increased with increasing copper content.     

Efficient decomposition of organic compounds with FeTiO3/TiO2 heterojunction under visible light irradiation

FeTiO₃/TiO₂, a new heterojunction-type photocatalyst working at visible light, was prepared by a simple sol–gel method. Not only did FeTiO₃/TiO₂ exhibit greatly enhanced photocatalytic activity in decomposing 2-propanol in gas phase and 4-chlorophenol in aqueous solution, but also it induced efficient mineralization of 2-propanol under visible light irradiation (λ ≥ 420 nm). Furthermore, it showed a good photochemical stability in repeated photocatalytic applications. FeTiO₃ showed a profound absorption over the entire visible range, and its valence band (VB) position is close to that of TiO₂. The unusually high photocatalytic efficiency of the FeTiO₃/TiO₂ composite was therefore deduced to be caused by hole transfer between the VB of FeTiO₃ and TiO₂.     

Capability of coupled CdSe/TiO2 heterogeneous structure for photocatalytic degradation and photoconductivity

Highly ordered TiO₂ nanotube arrays (TiO₂-NTAs), with a uniform tube size on titanium substrate, were obtained by means of reoxidation and annealing. A composite structure, CdSe quantum dots@TiO₂ nanotube arrays (CdSe QDs@TiO₂-NTAs), was fabricated by assembling CdSe quantum dots into TiO₂-NTAs via cyclic voltammetry electrochemical deposition. The X-ray diffractometer (XRD), field-emission scanning electron microscope (SEM), and transmission electron microscope (TEM) were carried out for the determination of the composition and structure of the tubular layers. Optical properties were investigated by ultraviolet-visible spectrophotometer (UV-Vis). Photocurrent response under visible light illumination and photocatalytic activity of samples by degradation of methyl orange were measured. The results demonstrated that the photo absorption of the composite film shifted to the visible region, and the photocurrent intensity was greatly enhanced due to the assembly of CdSe QDs. Especially, photocurrent achieved a maximum of 1.853 μA/cm² after five voltammetry cycles of all samples. After irradiation under ultra violet-visible light for 2 h, the degradation rate of composition to methyl orange (MO) reached 88.20%, demonstrating that the CdSe QDs@TiO₂-NTAs exhibited higher photocatalytic activity.     

Synergistic effects of doped Fe3+ and deposited Au on improving the photocatalytic activity of TiO2

Fe³⁺ doped together with Au deposited TiO₂ (Au/Fe³⁺–TiO₂) was successfully prepared, which shows excellent photocatalytic activity for degradation of methyl orange (MO) under both UV and visible light (λ > 420 nm) illumination. Fe³⁺ has been confirmed by EPR to substitute for Ti⁴⁺ in the TiO₂ lattice, and Au exists as Au⁰ on the surface of the photocatalyst indicated by the results of XRD. Fe³⁺ and Au have synergistic effects on improving the photocatalytic activity of TiO₂. A proposed mechanism concerning the synergistic effects is discussed to explain the improvement of the photocatalytic activities.     

Low Temperature Preparation and Characterization of N-doped and N-S-codoped TiO2 by Sol–gel Route

This paper reports a new method to prepare the N-doped and N-S-codoped anatase TiO₂ photocatalysts at 100 °C. The as-prepared photocatalysts were characterized by means of XRD, Raman spectra, TEM, BET, UV–Vis diffuse reflectance spectra (DRS) and XPS. The results showed that the N-doping and N-S-codoping extended the absorbance spectra of TiO₂ into visible region with different extent. The BET surface area of the N-S-codoped TiO₂ photocatalysts was high up to 245 m²g⁻¹. The results of degradation of methyl orange (MO) solution showed that the N-doped and N-S-codoped TiO₂ photocatalysts exhibited higher photocatalytic activity than that of Degussa P-25 and the as-prepared pure TiO₂ under visible irradiation. This property can be attributed to the results of synergetic effects of absorption in the visible light region, red shift in adsorption edge, good crystallization and large surface area of the as-prepared N-doped or N-S-codoped TiO₂.     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.     

Photocatalytic activity of TiO2 supported on multi-walled carbon nanotubes under simulated solar irradiation

TiO₂ particles supported on multi-walled carbon nanotubes (MWCNTs) were prepared using a sol–gel method to investigate their photocatalytic activity under simulated solar irradiation for the degradation of methyl orange (MO) in aqueous solution. The prepared composites were analyzed using XRD, SEM, EDS and UV–vis absorption spectroscopy. The results of this study indicated that there was little difference in the shape and structure of MWCNTs/TiO₂ composite and pure TiO₂ particles. The composite exhibited enhanced absorption properties in the visible light range compared to pure TiO₂. The degradation of MO by MWCNTs/TiO₂ composite photocatalysts was investigated under irradiation with simulated solar light. The results of this study indicated that MWCNTs played a significant role in improving photocatalytic performance. Different amounts of MWCNTs had different effects on photodegradation efficiency, and the most efficient MO photodegradation was observed for a 2% MWCNT/TiO₂ mass ratio. Photocatalytic reaction kinetics were described using the Langmuir–Hinshelwood (L–H) model. The photocatalyst was reused for eight cycles, and it retained over 95.2% photocatalytic degradation efficiency. Possible decomposition mechanisms were also discussed. The results of this study indicated that photocatalytic reactions with TiO₂ particles supported on MWCNTs under simulated solar light irradiation are feasible and effective for degrading organic dye pollutants.     

Preparation of transparent PVA/TiO2 nanocomposite films with enhanced visible-light photocatalytic activity

Polymer/semiconductor oxide nanocomposite films have been intensively investigated for various applications. In this work, we reported a simple hydrothermal method to fabricate highly transparent poly(vinyl alcohol)/titanium dioxide (PVA/TiO₂) nanocomposite films with enhanced visible-light photocatalytic activity. The as-prepared PVA/TiO₂ nanocomposite films showed high optical transparency in the visible region even at a high TiO₂ content (up to 40 wt.%). The determination of photocatalytic activity by photodegradation of methyl orange (MO) and colorless phenol showed that PVA/TiO₂ nanocomposite films exhibited enhanced visible-light photocatalytic activity and excellent recycle stability. This work provided new insights into fabrication of polymer/TiO₂ nanocomposites as high performance photocatalysts in waste water treatment.     

TiO2/Na-HZSM-5 nano-composite photocatalyst: Reversible adsorption by acid sites promotes photocatalytic decomposition of methyl orange

TiO₂/Na-HZSM-5 nano-composite photocatalysts were prepared by dispersing TiO₂ onto the external surface of Na⁺-modified nano-ZSM-5 zeolite using a sol–gel process. Samples were characterized by XRF, XPS, HRTEM, XRD, DRUV–vis, NH₃-TPD, FT-IR, and the adsorption and photodegradation of methyl orange (MO) in aqueous solution. Results show the modification of support by Na⁺ does not affect the loading, dispersion and structure of loaded TiO₂, but reduces the acidity of the nano-zeolitic support by preferentially eliminating stronger acid sites. The MO adsorption mainly takes place on the external surface of the supports. The strong and medium strong acid sites of the supports are the adsorption sites. MO molecules adsorbed by strong acid sites are difficult to desorb, whereas the adsorption of MO by medium strong acid sites is reversible. Generally, the MO photodegradation activity of TiO₂/Na-HZSM-5 nano-composites is better than that of bare TiO₂. However, it changes remarkably with the Na⁺ content of the supports, giving the maximum value at 1.1 wt.% Na⁺ when the MO adsorption by the support is almost completely reversible. The enhancement of the photodegradation activity of TiO₂/Na-HZSM-5 nano-composites is attributed to the reversible adsorption of MO by the medium strong acid sites on the nano-zeolitic supports.     

Facile synthesis and enhanced visible light photocatalytic activity of N and Zr co-doped TiO2 nanostructures from nanotubular titanic acid precursors

Zr/N co-doped TiO₂ nanostructures were successfully synthesized using nanotubular titanic acid (NTA) as precursors by a facile wet chemical route and subsequent calcination. These Zr/N-doped TiO₂ nanostructures made by NTA precursors show significantly enhanced visible light absorption and much higher photocatalytic performance than the Zr/N-doped P25 TiO₂ nanoparticles. Impacts of Zr/N co-doping on the morphologies, optical properties, and photocatalytic activities of the NTA precursor-based TiO₂ were thoroughly investigated. The origin of the enhanced visible light photocatalytic activity is discussed in detail.     

Preparation and Characterization of Multi-functional Titanium Dioxide Photocatalysts

Recent research trends of the preparation and characterization of highly efficient titanium oxide-based photocatalysts modified by different methods are reviewed on the basis of studies done in our laboratory. Special attention is focused on the preparation and characterization of TiO₂ photocatalysts prepared by the transitional metal doping and noble metal deposition method, especially combining above two methods. Fe³⁺ doped together with Au deposited TiO₂ (Au/Fe³⁺–TiO₂) was successfully prepared, which shows excellent photocatalytic activity for degradation of methyl orange (MO) under both UV and visible light (λ > 420 nm) illumination. Fe³⁺ has been confirmed by EPR to substitute for Ti⁴⁺ in the TiO₂ lattice, and Au exists as Au⁰ on the surface of the photocatalyst indicated by the results of XRD. Fe³⁺ and Au have synergistic effects on improving the photocatalytic activity of TiO₂. A proposed mechanism concerning the synergistic effects is discussed to explain the improvement of the photocatalytic activities.     

Photocatalytic degradation of azo dye using TiO2 supported on spherical activated carbon

TiO₂ supported on spherical activated carbon (TiO₂/SAC) was prepared through an ion-exchange method followed by a heat-treatment process. The adsorption characteristic of TiO₂/SAC was evaluated using azo dye methyl orange (MO) as a target substance, and the photocatalytic degradation of MO under UV irradiation was also discussed. A synergistic effect of both the adsorption capacity of activated carbon and the photoactivity of TiO₂ on the removal of MO from aqueous solution was observed. Experimental results revealed that the photocatalytic degradation of MO improved with increasing photocatalyst dosage and followed a pseudo-first order kinetic. After five-cycle runs, TiO₂/SAC still exhibited relatively high photocatalytic characteristic for the degradation of MO. Besides, the prepared TiO₂/SAC can be helpful in the easy separation of photocatalyst from solution after photocatalysis of MO. Furthermore, the use of liquid chromatography/mass spectrometry (LC/MS) technique, identified three intermediates as degradation products during the photocatalytic reaction of MO with TiO₂/SAC.     

The construction of TiO2 NTs/Ag3PO4–AgBr by SILAR deposition as promising photocatalysts for hydrogen production and pollutant treatment

The construction of ternary TiO₂ NTs/Ag₃PO₄–AgBr photocatalysts was carried out by the SILAR deposition of Ag₃PO₄ and AgBr on TiO₂ nanotube arrays (TiO₂ NTs) for enhancing the photocatalytic application in H₂ evolution and dyeing wastewater remediation. The adjustment of Ag₃PO₄/AgBr deposition cycles was used to optimize the optical absorption and photocatalytic property. The TiO₂ NTs/Ag₃PO₄–AgBr (5) prepared with 5 cycle deposition of Ag₃PO₄ and AgBr exhibited the optimal photoelectric activity and photocatalytic performances. The photocatalytic rate constants for the degradation of MO, RhB and MB dyes achieved 1.35 × 10⁻², 3.30 × 10⁻² and 4.47 × 10⁻² min⁻¹, respectively, and the visible light-driven photocatalytic H₂ evolution rate achieves 46.87 μmol cm⁻² h⁻¹. •O₂⁻ radicals exhibited the key influence on the organic dye degradation, and the as-prepared photocatalysts showed exceedingly high photocatalytic activity and stability. Furthermore, the photocatalytic mechanism was proposed based on the ESR result.     

Visible photocatalytic activity and photoelectrochemical behavior of TiO2 nanoparticles modified with metal porphyrins containing hydroxyl group

TiO₂ nanoparticles modified with 5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin (HTPP), 5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin zinc (ZnHTPP) and trans-dichloro-5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin tin (SnHTPP) were prepared in order to improve the visible photocatalytic activity of TiO₂ nanoparticles. The photocatalytic activity of the modified TiO₂ nanoparticles was investigated by carrying out the photodegradation of methyl orange in aqueous solution under visible light irradiation. The TiO₂ nanoparticles modified with SnHTPP show the highest visible photocatalytic activity with a degradation ratio of 86% of methyl orange after 180 min irradiation among three catalysts. This result indicates that the central metal ions in porphyrins can significantly influence the sensitization efficiency of porphyrins. In addition, the photoelectrochemical behavior of the modified TiO₂ nanoparticles was examined and related to their photocatalytic activity. Finally, the photocatalytic mechanism was discussed preliminarily.     

Enhanced visible light-induced photoelectrocatalytic degradation of phenol by carbon nanotube-doped TiO2 electrodes

We used a modified sol-gel method to prepare titanium dioxide and multi-walled carbon nanotube (CNT) composites that we subsequently deposited onto indium tin oxide (ITO) conductive glass plates. We characterized these CNT-doped TiO₂ (CNT-TiO₂) films using X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and diffuse reflectance UV-vis spectroscopy. The photoelectrocatalytic (PEC) activity of the composites was evaluated through their ability to mediate the degradation of phenol. XRD measurements indicated that the TiO₂ component existed solely in the anatase phase and that the crystallinity of the CNTs was low. XPS indicated that carbon atoms could substitute for both oxygen and titanium atoms in the TiO₂ lattice to form Ti-C and Ti-O-C structures, which were responsible for the extra photoabsorption and PEC activity under illumination with visible light, in addition to those provided by the CNTs and carbonaceous and Ti³⁺ species. An interphase interaction between TiO₂ and the CNTs elevated the photoabsorbance of the composites in the visible light region. A sample of TiO₂ doped with 10% CNTs and calcined at 400 °C exhibited the highest photocurrent and PEC efficiency. We systematically investigated the effects of several parameters of the PEC process, including the applied potential and pH, on the phenol conversion.     

Hydrothermal growth of TiO2 nanowire membranes sensitized with CdS quantum dots for the enhancement of photocatalytic performance

In this paper, TiO₂ nanowires (NWs) on Ti foils were prepared using a simple hydrothermal approach and annealing treatment. CdS quantum dots (QDs) were assembled onto the crystallized TiO₂ NWs by sequential chemical bath deposition. Ultraviolet-visible absorption spectra showed that CdS adds bands in the visible to the TiO₂ absorption and exhibited a broad absorption band in the visible region, which extended the scope of absorption spectrum and helped improve the photocatalytic degradation efficiency. The results of photocatalytic experiment revealed that CdS-TiO₂ NWs possessed higher photocatalytic activities toward methyl orange than pure TiO₂ nanowires. The degradation efficiency of 96.32% after ten cycles indicated that the as-prepared CdS-TiO₂ composite exhibited excellent long-time recyclable ability and can be reused for the degradation of contaminants.     

Synthesis and characterization of polythiophene/titanium dioxide composites

Polythiophene/titanium dioxide (PT/TiO₂) composites were prepared by the in situ chemical oxidative polymerization method. The resulting PT/TiO₂ composites were characterized by Fourier transform infrared (FT-IR) spectroscopy, ultraviolet–visible (UV–Vis) diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and field emission scanning electron microscopy (SEM). UV–Vis diffuse reflectance spectra measurements show that the PT/TiO₂ composites can adsorb light of wavelengths ranging from 200 nm to 800 nm. The PT/TiO₂ composites showed good adsorption properties and were more efficient in removing dye from solution than pure PT and pure TiO₂. The PT/TiO₂ composites exhibited photocatalytic activities to some extent under UV light illumination.     

Photocatalytic Properties of Silica-supported TiO2

TiO₂ supported on SiO₂ surface is effective on the recovery of photocatalyst, morphological control, and coating on the substrate. Furthermore, it shows much higher photocatalytic activity than pure TiO₂. The silica support is quite influential on the surface properties of TiO₂ supported on SiO₂. The enhanced photocatalytic activity of TiO₂–SiO₂ could be explained by the effects of surface area, adsorption, band-gap energy and local structure. However, it is difficult to say which one is the most important factor responsible for the photocatalytic property of TiO₂–SiO₂. For example, the reduction of particle size could effect on both of the surface area and band-gap energy. And, Ti–O–Si bonds could modify the band-gap energy and local structure. Therefore, the photocatalytic properties of TiO₂–SiO₂ should be expressed by sum of many factors such as surface area, adsorption, band-gap energy and local structure.     

Template-assisted hydrothermal synthesis and photocatalytic activity of novel TiO2 hollow nanostructures

TiO₂ hollow nanostructures were successfully synthesized by a controlled hydrothermal precipitation reaction using Resorcinol–Formaldehyde resin spheres as templates in aqueous solution, and then removal of the RF resins spheres by calcination in air at 450 °C for 4 h. The obtained TiO₂ hollow spheres were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, N₂ adsorption–desorption analysis, and UV–visible diffuse reflectance spectroscopy. The photocatalytic activity of the as-prepared samples was evaluated by photocatalytic decolorization of rhodamine B aqueous solution at ambient temperature under UV illumination. The results indicated TiO₂ hollow nanostructures exhibit the excellent photocatalytic activity probably due to the unique hollow micro-architectures.