Conversion of green emission into white light in Gd2O3 nanophosphors

Gd₂O₃ nanophosphors were prepared by combustion synthesis with and without doping of Dy³⁺ ions. The X-ray powder diffraction patterns indicate that as-prepared Gd₂O₃ and 0.1 mol% Dy₂O₃ doped Gd₂O₃ nanophosphors have monoclinic structures. The transmission electron microscope (TEM) studies revealed that the as-prepared phosphors had an average crystallite sizes around 37 nm. The excitation and emission properties have been investigated for Dy³⁺ doped and undoped Gd₂O₃ nanophosphors. New emission bands were observed in the visible region for Gd₂O₃ nanophosphors without any rare earth ion doping under different excitations. A tentative mechanism for the origin of luminescence from Gd₂O₃ host was discussed. Emission properties also measured for 0.1 mol% Dy³⁺ doped Gd₂O₃ nanophosphors and found the characteristic Dy³⁺ visible emissions at 489 and 580 nm due to ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions, respectively. The chromaticity coordinates were calculated based on the emission spectra of Dy³⁺ doped and undoped Gd₂O₃ nanophosphors and analyzed with Commission Internationale de l'Eclairage (CIE) chromaticity diagram. These nanophosphors exhibit green color in undoped Gd₂O₃ and white color after adding 0.1 mol% Dy₂O₃ to Gd₂O₃ nanophosphors under UV excitation. These phosphors could be a promising phosphor for applications in flat panel displays.     

Research status of novel La2Mo2O9-based oxide-ion conductors

La2Mo2O9-based oxide-ion conductors have attracted more and more attention since the high ionic con-ductivity was reported in 2000 by Lacorre et al.in this kind of material.In this paper the recent inv...     

The study on electrical behavior of Gd2O3-WO3 complex ceramics at high temperature

Gd₂O₃-WO₃ complex ceramics are fabricated by the conventional solid-state reaction process. The electrical characteristics and dielectric properties of the samples were measured at various ambient temperatures in a low electric field (E < 150 V/mm). As the temperature increases, the dielectric constant and the loss tangent show an obvious change at about 50 °C and 330 °C. When the temperature is above 200 °C, the samples display stable nonlinear electrical properties characterized by semiconductivity, and the nonlinearity increases along with increasing temperature. XRD analysis reveals that Gd₂W₂O₉ is the main phase and Gd₂O₃ is the secondary phase. Based on the phase transition of tungsten trioxide, these electrical properties of Gd₂O₃-WO₃ complex ceramics can be simply explained.     

Design and achieving mechanism of upconversion white emission based on Yb/Tm/Er tri-doped KY3F10 nanocrystals

KY₃F₁₀:Yb³⁺/Tm³⁺/Er³⁺ upconversion nanocrystals are synthesized via a simple hydrothermal procedure. The nanocrystals emit the near equal energy white light with high brightness and favorable color balance when excited using a 980 nm continuous wave diode laser. The research of upconversion mechanism indicates that in addition to the energy transfer processes from Yb³⁺ to Tm³⁺ and Er³⁺, respectively, there exists a new process ¹G₄ (Tm³⁺) + ⁴I_11/2 (Er³⁺) → ³H₄ (Tm³⁺) + ⁴S_3/2 (Er³⁺).     

Observation of broadband infrared luminescence in a novel Bi-doped P2O5-B2O3-Al2O3 glass

A novel Bi-doped P₂O₅-B₂O₃-Al₂O₃ glass was investigated, and strong broadband NIR (near infrared) luminescence was observed when the sample was excited by 445 nm, 532 nm, 808 nm and 980 nm lasers, respectively. The max FWHM with 312 nm, the lifetime with 580 μs and the σ_emτ product with 5.3 × 10^− 24 cm² s were obtained which indicates that this glass is a promising material for broadband optical amplifier and tunable laser. The effect of the introduction of B₂O₃ on the glass structure and Bi-ions illuminant mechanism were discussed and analyzed. It is suggested that the introduction of B₂O₃ makes the glass structure closer, and the broadband NIR emission derives from Bi⁰:²D_3/2 → ⁴S_3/2 and Bi⁺:³P₁ → ³P₀ transitions.     

La2O3、Nd2O3、Y2O3对高岭石高温相变动力学的影响

利用综合热分析技术、X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)和扫描电镜(SEM)研究了La_2O_3、Nd_2O_3、Y_2O_3对高岭石高温条件下转变成莫来石过程的作用,并采用Kissinger方程、Ozawa方程以及JMA修正方程(Ⅰ)和(Ⅱ)分析了La_2O_3、Nd_2O_3、Y_2O_3对高岭石高温相变动力学的影响。结果表明:3种稀土氧化物的掺入对高岭石的相变动力学参数产生了影响,相变活化能和频率因子与未掺入稀土氧化物的高岭石相比有所降低,析晶方式则未发生变化,均属于体积晶化。对比掺入3种稀土氧化物的高岭石相变活化能和频率因子可以看出,Y_2O_3对于高岭石高温条件下相变的促进作用最为明显,相变活化能最低。稀土氧化物对于高岭石高温相变产物影响不大,主晶相为莫来石相,次晶相为方石英相,但稀土氧化物的掺入使得方石英相的结晶度明显提高。     

Synthesis and photoluminescent properties of Gd3O4Br:Er phosphors prepared by solid-state reaction method

Pure orthorhombic Gd₃O₄Br:Er³⁺ upconversion phosphors were synthesized by a solid-state reaction method and the structural properties of Gd₃O₄Br:Er³⁺ were investigated by X-ray diffraction; field emission scanning electron microscopy, Raman spectroscopy and Fourier transform infrared spectroscopy. The results show that Gd₃O₄Br has low phonon cutoff energy, indicating that Gd₃O₄Br:Er³⁺may have high luminescent efficiency. Intense green (514–582 nm) and strong red (645–692 nm) upconverted luminescence of Gd₃O₄Br:Er³⁺ were observed under 980 nm laser excitation. The bright green emission is visible to the naked eyes even for 1 mW of the pump power (980 nm) for Gd₃O₄Br:Er³⁺ (0.1%) samples, indicating that Gd₃O₄Br:Er³⁺ may be used as upconversion phosphors.     

Hydrothermal synthesis, structure and scintillation characterization of nanocrystalline Eu-doped Gd2O3 materials and its X-ray imaging applications

Nanocrystalline Gd₂O₃:Eu scintillators were successfully synthesized using a hydrothermal method and subsequent calcination treatment in the electrical furnace as an X-ray to visible light conversion material for an indirect X-ray image sensor. In this work, various Gd₂O₃:Eu scintillators were prepared in accordance with different synthesis conditions such as doped-Eu concentration, different calcination temperatures of 600-1400 °C and calcination time of 1-10 h. The transition of morphology from nanorods to particles was observed as the calcination temperature of Gd₂O₃:Eu scintillator increased. And the phase transformation of the sample from cubic to monoclinic structure was discovered at 1300 °C calcination temperature. In addition, scintillation properties such as luminescent spectra and light intensity under 266 nm UV illumination were measured as a function of calcination condition of as-synthesized Gd₂O₃:Eu powder. The nanocrystalline Gd₂O₃:Eu scintillator with a strong red light emission at near 611 nm wavelength under photo- and X-ray excitation will be employed for its potential X-ray image sensor applications in the future.     

Structural and spectroscopic characterization of Yb doped Lu2O3 transparent ceramics

Yb³⁺ doped Lu₂O₃ transparent ceramics were fabricated by the solid-state reaction method and sintered in H₂ atmosphere. Structural and spectroscopic properties of Yb:Lu₂O₃ ceramics were studied. The Yb:Lu₂O₃ ceramic structure, and the lattice parameter are refined with the Rietveld method. Yb:Lu₂O₃ has broad absorption and emission bands with a long fluorescence lifetime (1.31 ms). The energy level diagram is calculated based on the absorption and emission spectra, Yb³⁺ in Lu₂O₃ ceramics exhibits a big splitting energy of the ²F_7/2 ground state (1023 cm⁻¹). Furthermore, the gain cross-section (σ_g) is estimated with different β values.     

Structural transition induced by the release of residual stress in the complex of cubic and monoclinic Gd2O3:Eu nanoparticles

The Photoluminescence (PL) spectra of Gd₂O₃:Eu composed of cubic and monoclinic structure were collected on November 2003 and June 2006, respectively. The results show that a portion of cubic Gd₂O₃ transforms into monoclinic after the sample was left as it is for two years; and the ⁵D₁-⁷F_J emission of Eu³⁺ in cubic host was enhanced in this released complex. Considering the high pressure behavior of Gd₂O₃, we think this structural transition is due to the sample that endures a process of press and release while the residual stress is released slowly.     

Growth and Characterization of YbBCO Films on Textured Gd2O3 Buffer-Layered Ni Tapes: All Sol–Gel Process

YbBa₂Cu₃O_7–x (YbBCO) thick films were grown on buffered, cube-textured Nickel tapes by sol–gel dip-coating method. Yb-123 films were prepared using solutions of Yb, Ba, and Cu organometallic compounds. A solution-based Gd₂O₃ buffer layer was deposited by dip-coating process with excellent texture and uniformity. The texture development and surface morphology of the buffer-layer films were examined by X-ray diffraction, pole figures, and ESEM analysis. Microstructure and characterization of Yb-123 films were done by ESEM, EDS, and XRD analysis. T _c and J _c were conducted by four-wire measurement method     

Y2O3添加量对Al2O3/ZrO2共晶陶瓷显微组织及力学性能的影响

为探索第三组元Y₂O₃添加对Al₂O₃/ZrO₂共晶陶瓷显微组织与机械性能的影响,本文利用低温度梯度的高温熔凝法制备了直径为20 mm的Al₂O₃/ZrO₂(Y₂O₃)共晶陶瓷块体,采用SEM、EDS及XRD技术对共晶陶瓷进行微结构分析,并利用维氏压痕法对其硬度和断裂韧性进行测试。SEM结果表明,凝固组织由群集的共晶团结构组成,随着Y₂O₃添加量的增加,共晶团形态由胞状转变为枝晶状,内部相间距在1~2 μm范围内变化。力学测试表明,Y₂O₃摩尔分数小于1.1%时,由于组织内部存在低硬度m-ZrO₂及微裂纹缺陷,故陶瓷硬度较低,约为(9.53±0.22 )GPa;当Y₂O₃摩尔分数为1.1%时,陶瓷硬度最大,约为(18.05±0.27)GPa;当Y₂O₃的摩尔分数大于1.1%时,由于共晶团边界区内气孔缺陷及粗大组织增多,引起陶瓷硬度值略有下降。低Y₂O₃摩尔分数添加时,陶瓷断裂韧性相对较高,约为(6.30±0.16)MPa·m^1/2,这与其内部存在大量微裂纹缺陷有关;随着Y₂O₃添加量的增加,陶瓷的微裂纹数量减少、边界区内缺陷增多,断裂韧性降低。     

Efficient Bi → Nd energy transfer in Gd2O3:Bi,Nd

Bi³⁺,Nd³⁺ co-doped Gd₂O₃ were prepared by solid state reaction and the optical properties were investigated. The results show that the near-infrared emission of Nd³⁺ ions is significantly enhanced by the introducing of Bi³⁺ in co-doped samples. An efficient energy transfer from Bi³⁺ to Nd³⁺ corresponds to the near-infrared emission enhancement. The energy transfer efficiency reaches 64.1% for the sample with the strongest near-infrared emission, which has the optimized doping concentrations of 0.5% for Bi³⁺ and 2% for Nd³⁺. The interesting optical properties make Bi³⁺,Nd³⁺ co-doped Gd₂O₃ promising as the luminescent down-conversion layers in front of c-Si solar cells to enhance the performance of the solar cells.     

Electrical conductivity of 5 mol.% Yb2O3 and 5 mol.% Gd2O3 co-doped Sm2Zr2O7

Sm₂Zr₂O₇ co-doped with and without 5 mol.% Yb₂O₃ and 5 mol.% Gd₂O₃ were prepared by a pressureless-sintering method at 1973 K for 10 h in air. The relative density, structure and electrical conductivity were investigated by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance spectra measurements. Both Sm₂Zr₂O₇ and (Sm_0.9Gd_0.05Yb_0.05)₂Zr₂O₇ ceramics exhibit a single phase of pyrochlore-type structure. The grain conductivity, grain-boundary conductivity and total conductivity obey the Arrhenius relation, respectively, and gradually increase with increasing temperature from 723 to 1173 K. (Sm_0.9Gd_0.05Yb_0.05)₂Zr₂O₇ ceramic is the oxide-ion conductor in an oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The grain conductivity, grain-boundary conductivity and total conductivity of (Sm_0.9Gd_0.05Yb_0.05)₂Zr₂O₇ with dual Yb³⁺ + Gd³⁺ doping are higher than those of undoped Sm₂Zr₂O₇ at identical temperature levels.     

Fabrication of nanostructure Al2O3/ZrO2 (Y2O3) eutectic by combustion synthesis melt-casting under ultra-high gravity

A novel method for preparing Al₂O₃/ZrO₂ (Y₂O₃) eutectic was developed by combining combustion synthesis with melt-casting under ultra-high gravity (CSMC-UHG). The application of UHG = 800 g resulted in a high relative density of 99.8%, and an orientation-growth along the UHG direction. The microstructure was composed of aligned growth regimes containing a triangular dispersion of orderly ZrO₂ rods in Al₂O₃ matrix with a spacing of 300 nm. The eutectic had a high fracture toughness up to 17.9 MPa·m^1/2, which was mainly attributed to the nanostructure and the elastic bridge effects of the aligned ZrO₂ rods.     

Preparation and luminescence properties of nanocrystalline La2O3:Eu phosphor

Powders La₂O₃ doped with 1 mol% Eu were prepared via a combustion route using different reducers (urea, glycine and citric acid). The structure and morphology were determined with XRD and HRTEM measurement. The main emission positions centered at 626 nm for ⁵D₀ → ⁷F₂ transition are observed. The variation of CT band with different reducers is observed. The intensity of ⁵D₀ → ⁷F₂ transition centered at 626 nm with respect to that of ⁵D₀ → ⁷F₁ transition is a function of the energy difference ΔE between the two CT band positions.     

Local thermal effect at luminescent spot on upconversion luminescence in Y2O3:Er,Yb nanoparticles

Y₂O₃:Er³⁺,Yb³⁺ nanoparticles were synthesized using Pechini type sol-gel method and then characterized by XRD, TEM, SEM, Raman spectroscopy, and fluorescence spectrophotometer. Local temperature effect on upconversion luminescence intensities was theoretically analyzed and experimentally tested. These results indicate that a competition process between local temperature at luminescent spot and laser pump power density decides the development trend of upconversion luminescence intensity. Therefore, it can be concluded that the most intensive upconversion luminescence in Y₂O₃:Er³⁺,Yb³⁺ nanoparticles can be achieved at a certain pump power density, which should be slightly below a given constant value (the corresponding threshold of temperature).     

纳米-Al2O3/SiO2加入量对MgO-Al2O3-SiO2复相陶瓷烧结机理的影响

为了探究纳米-Al₂O₃/SiO₂加入量对MgO-Al₂O₃-SiO₂复相陶瓷烧结行为的作用机理。以微米级MgO、纳米级Al₂O₃和SiO₂为主要原料制备陶瓷基复合材料。通过XRD和 SEM等检测手段对烧后试样的物相组成和微观结构进行测试与表征,重点研究Al₂O₃/SiO₂的加入对复相陶瓷物相组成、微观结构及烧结性能的影响。结果表明:随着Al₂O₃/SiO₂加入量的增大,试样烧后相对密度和烧后线变化率呈先增大后减小再增大的趋势,加入15%Al₂O₃/SiO₂(质量分数)的试样经1 500 ℃烧结后,其相对密度可以达到94%。引入的Al₂O₃/SiO₂与基体中的MgO生成镁铝尖晶石与镁橄榄石相,原位反应伴随的体积膨胀,抵消部分烧结过程中的体积收缩。Al₂O₃/SiO₂加入量为75%(质量分数)的试样经1 400 ℃烧结后,基体中有大量堇青石相生成,随着煅烧温度提高到1 500 ℃,堇青石分解所产生的高温液相促进了试样的烧结收缩。     

Varistor properties of ZnO-Pr6O11-CoO-Cr2O3-Y2O3-In2O3 ceramics

The varistor properties of the ZnO-Pr₆O₁₁-CoO-Cr₂O₃-Y₂O₃-In₂O₃ ceramics were investigated for different concentrations of In₂O₃. The increase of In₂O₃ concentration slightly increased the sintered density (5.60-5.63 g/cm³) and slightly decreased the average grain size (3.4-2.9 μm). The breakdown field increased from 6023 to 14822 V/cm with increasing concentration of In₂O₃. The nonlinear coefficient increased from 17.6 to 44.6 for up to 0.005 mol%, whereas the further doping caused it to decrease to 36.8. In₂O₃ acted as an acceptor due to the donor concentration, which decreases in the range of 1.02 × 10¹⁷ to 0.24 × 10¹⁷/cm³ with increasing concentration of In₂O₃.     

Up-conversion emission in KGd(WO4)2 single crystals triply-doped with Er/Yb/Tm, Tb/Yb/Tm and Pr/Yb/Tm ions

Triply-doped single crystals KGd(WO₄)₂:Er³⁺/Yb³⁺/Tm³⁺, KGd(WO₄)₂:Tb³⁺/Yb³⁺/Tm³⁺ and KGd(WO₄)₂:Pr³⁺/Yb³⁺/Tm³⁺ were grown by the Top Seeded Solution Growth (TSSG) method, with an aim of getting efficient up-converted multicolored luminescence, which subsequently can be used for generation of white light. Such an aim determined the choice of the triply doped compounds: excitation of the Yb³⁺ ions in the infrared spectral region is followed by red, green and blue emission from other dopants. It was shown that all these systems exhibit multicolor up-conversion fluorescence under 980 nm laser irradiation. Detailed spectroscopic studies of their absorption and luminescence spectra were performed. From the analysis of the dependence of the intensity of fluorescence on the excitation power the conclusion was made about significant role played by the host’s conduction band and other possible defects of the KGd(WO₄)₂ crystal lattice in the up-conversion processes.