BaTiO3-SrTiO3 layered dielectrics for energy storage

BaTiO₃-SrTiO₃ (BST) thick films (~ 250-390 μm) with layered structures were fabricated by tape-casting and lamination process. Layered composites with various Ba/Sr ratios were obtained by lamination of BaTiO₃ (BT) and SrTiO₃ (ST) tapes in different spatial configurations (2-2). As-prepared BST ceramics showed much improved sinterability over the laminates of pure BT or pure ST tapes. Dielectric properties of materials were measured in the temperature range of 25 °C to 200 °C. The method of utilizing of layered structures offered flexibility to maximize the energy storage capability at specific operating conditions: (temperature and electric field) by tailoring the dielectric properties through varying the spatial configurations of BT and ST films.     

Effects of Ho2O3 addition on defects of BaTiO3

Effects of Ho₂O₃ addition on defects of BaTiO₃ ceramic have been studied in terms of electrical conductivity at 1200 °C as a function of oxygen partial pressure (P_O2°) and oxygen vacancy concentration. The substitution of Ho³⁺ for the Ti site in Ba(Ti_1−xHo_x)O_3−0.5x resulted in a significant shift of conductivity minimum toward lower oxygen pressures and showed an acceptor-doped behavior. The solubility limit of Ho on Ti sites was confirmed less than 3.0 mol% by measuring the electrical conductivity and the lattice constant. Oxygen vacancy concentrations were calculated from the positions of P_O2° in the conductivity minima and were in good agreement with theoretically estimated values within the solubility limit. The Curie point moved to lower temperatures with increasing the oxygen vacancy concentration and Ho contents.     

Effects of Bi2O3 and Cr2Ti3O9 Co-doping on dielectric properties in BaTiO3-based ceramics

A microwave ceramic with general composition (1-x-y) BaTiO₃ + x Cr₂Ti₃O₉ + y Bi₂O₃ has been prepared by solid state synthesis at 1300-1400 °C. The phase composition, perovskite structural parameters and dielectric properties have been obtained by X-ray diffraction and dielectric measurements as a function of chemical composition and temperature. At low doping levels the formation of BaTiO₃-based solid solution has been found. The precipitation of BaCrO₃ has been detected at x = y = 2.0 mol%. A model of the incorporation of Cr³⁺ and Bi³⁺ ions into BaTiO₃-based crystal lattice has been proposed. Diffused phase transition in the temperature range 100-140 °C have been revealed by dielectric measurements for different ceramic composition. As high dielectric constant as 7311 and as low dielectric loss as 0.02 have been found for the composition of 0.98BaTiO₃-0.01Cr₂Ti₃O₉-0.01Bi₂O₃.     

Study and fabrication of ZnNb2O6 thin films by sol-gel method

Zinc niobium oxide (ZnNb₂O₆) thin films were grown on ITO/glass substrate by sol-gel process. Microstructure and surface morphology of the ZnNb₂O₆ thin films have been studied by X-ray diffraction and scanning electron microscopy. Optical properties of the ZnNb₂O₆ thin films were obtained by UV-visible recording spectrophotometer. The dependence of the microstructure, optical transmittance spectra, optical band gap on annealing temperature was also investigated.     

Varistor properties of ZnO-Pr6O11-CoO-Cr2O3-Y2O3-In2O3 ceramics

The varistor properties of the ZnO-Pr₆O₁₁-CoO-Cr₂O₃-Y₂O₃-In₂O₃ ceramics were investigated for different concentrations of In₂O₃. The increase of In₂O₃ concentration slightly increased the sintered density (5.60-5.63 g/cm³) and slightly decreased the average grain size (3.4-2.9 μm). The breakdown field increased from 6023 to 14822 V/cm with increasing concentration of In₂O₃. The nonlinear coefficient increased from 17.6 to 44.6 for up to 0.005 mol%, whereas the further doping caused it to decrease to 36.8. In₂O₃ acted as an acceptor due to the donor concentration, which decreases in the range of 1.02 × 10¹⁷ to 0.24 × 10¹⁷/cm³ with increasing concentration of In₂O₃.     

Piezoelectric, ferroelectric and dielectric properties of La2O3-doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

La₂O₃ (0–0.8 wt.%)-doped (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ (abbreviated as BNBT6) lead-free piezoelectric ceramics were synthesized by conventional solid-state reaction. The influences of La₂O₃ on the microstructure, the dielectric, ferroelectric and piezoelectric properties of the composites were investigated. X-ray diffraction (XRD) patterns indicate that 0.2-0.8 wt.% of La₂O₃ has diffused into the lattice of BNBT6 ceramics. Consequently, a pure perovskite phase is formed. SEM images show that the microstructure of the ceramics is changed with the addition of a small amount of La₂O₃. The temperature dependence of the relative dielectric constant shows that Curie point decreases with the increase of La₂O₃. At room temperature, the ceramics doped with 0.6 wt.% La₂O₃ show superior performance with high piezoelectric constant (d₃₃ = 167 pC/N), high planar electromechanical coupling factor (k_p = 0.30), high mechanical quality factor (Q_m = 118), high relative dielectric constant (ε_r = 1470) and lower dissipation factor (tanδ = 0.056) at a frequency of 10 kHz.     

Effect of working pressure on the properties of BaTiO3-CoFe2O4 composite films deposited on STO (100) by PLD

The BaTiO₃-CoFe₂O₄ (BTO-CFO) composite films were grown on SrTiO₃ (STO) (100) substrates at 750 °C under various working pressures by pulsed laser deposition. The composite film grew into a supersaturated single phase at the working pressure of 10 mTorr, BTO and CFO (00 l) oriented hetero-epitaxial films on STO (100) at 100 mTorr, and a polycrystalline composite film at 500 mTorr. The slow growth rate at high working pressure led to the phase separation in the composite film. The CFO was compressively strained along out-of-plane due to the lattice mismatch with the BTO matrix phase. The BTO-CFO composite film grown at 100 mTorr showed reversible switching of ferroelectric polarization and magnetic hysteresis with strong magnetic anisotropy.     

Y2O3添加量对Al2O3/ZrO2共晶陶瓷显微组织及力学性能的影响

为探索第三组元Y₂O₃添加对Al₂O₃/ZrO₂共晶陶瓷显微组织与机械性能的影响,本文利用低温度梯度的高温熔凝法制备了直径为20 mm的Al₂O₃/ZrO₂(Y₂O₃)共晶陶瓷块体,采用SEM、EDS及XRD技术对共晶陶瓷进行微结构分析,并利用维氏压痕法对其硬度和断裂韧性进行测试。SEM结果表明,凝固组织由群集的共晶团结构组成,随着Y₂O₃添加量的增加,共晶团形态由胞状转变为枝晶状,内部相间距在1~2 μm范围内变化。力学测试表明,Y₂O₃摩尔分数小于1.1%时,由于组织内部存在低硬度m-ZrO₂及微裂纹缺陷,故陶瓷硬度较低,约为(9.53±0.22 )GPa;当Y₂O₃摩尔分数为1.1%时,陶瓷硬度最大,约为(18.05±0.27)GPa;当Y₂O₃的摩尔分数大于1.1%时,由于共晶团边界区内气孔缺陷及粗大组织增多,引起陶瓷硬度值略有下降。低Y₂O₃摩尔分数添加时,陶瓷断裂韧性相对较高,约为(6.30±0.16)MPa·m^1/2,这与其内部存在大量微裂纹缺陷有关;随着Y₂O₃添加量的增加,陶瓷的微裂纹数量减少、边界区内缺陷增多,断裂韧性降低。     

The effect of Sb2O5 additions on the dielectric properties of Ag(Nb0.8Ta0.2)O3 ceramics

The sintering behavior and dielectric properties for perovskite Ag(Nb_0.8Ta_0.2)O₃ ceramic with Sb₂O₅ doping was explored. A small amount of Sb₂O₅ (2.5 wt.%) led to high densification at temperatures < 1060 °C. The dielectric constant increased and the temperature coefficient decreased with increasing concentration of Sb₂O₅, and the dielectric constant reached 673, combined with a low temperature coefficient of 147 ppm/°C, and dielectric loss of 0.0044 (at 1 MHz) for the sample with 3.5 wt.% Sb₂O₅ sintered at 1080 °C.     

Influence of Ga2O3 addition on transparent conductive oxide films of In2O3-ZnO

Influence of incorporation of Ga in amorphous In-Zn-O transparent conductive oxide films was investigated as a function of Zn/(Zn + In). For In-Zn-O films with no Ga₂O₃, the range of Zn/(Zn + In) ratio where the amorphous phase appears became narrow at a substrate temperature of 250 °C. With increasing Ga₂O₃ quantity, amorphous films were obtained even at a high substrate temperature of 250 °C in a wider range of Zn/(Zn + In) than that of In-Zn-O films with no Ga₂O₃. This means that the trend of crystallization at higher substrate temperature was disturbed with additional Ga incorporation. For the film deposited from ZnO:Ga (Ga₂O₃: 4.5-7.5 wt%) and In₂O₃ targets, we obtained a resistivity of 2.8 × 10⁻⁴ Ω cm, nearly the same value as that for an In-Zn-O film with no Ga₂O₃. The addition of more than 7.5 wt% Ga₂O₃ induced a widening of the optical band gap.     

La2O3、Nd2O3、Y2O3对高岭石高温相变动力学的影响

利用综合热分析技术、X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)和扫描电镜(SEM)研究了La_2O_3、Nd_2O_3、Y_2O_3对高岭石高温条件下转变成莫来石过程的作用,并采用Kissinger方程、Ozawa方程以及JMA修正方程(Ⅰ)和(Ⅱ)分析了La_2O_3、Nd_2O_3、Y_2O_3对高岭石高温相变动力学的影响。结果表明:3种稀土氧化物的掺入对高岭石的相变动力学参数产生了影响,相变活化能和频率因子与未掺入稀土氧化物的高岭石相比有所降低,析晶方式则未发生变化,均属于体积晶化。对比掺入3种稀土氧化物的高岭石相变活化能和频率因子可以看出,Y_2O_3对于高岭石高温条件下相变的促进作用最为明显,相变活化能最低。稀土氧化物对于高岭石高温相变产物影响不大,主晶相为莫来石相,次晶相为方石英相,但稀土氧化物的掺入使得方石英相的结晶度明显提高。     

Semiconducting BaTiO3-CuO mixed oxide thin films for CO2 detection

A full study of the BaTiO₃-CuO thin-film technology properties as carbon dioxide sensing material is presented. The coatings are deposited by RF-Sputtering and the CO₂ concentration is monitored by impedance measurements. Theoretical foundations are correlated to the experimental results and the principal fabrication and operation parameters are clarified: working temperature and frequency, thickness influence and the introduction of silver as an additive. The BaTiO₃-CuO layer shows higher sensitivity than the actual low-cost commercial CO₂ sensors in the range of the principal applications.     

Study on the microstructure and dielectric properties of X9R ceramics based on BaTiO3

This paper investigated the microstructure and dielectric properties of BaTiO₃-Pb(Sn, Ti)O₃ system ceramics. The Curie point of BaTiO₃ is 130 °C. When the temperature is higher than 130 °C, the dielectric constant of BaTiO₃ drops severely according to Curie-Weiss law. Pb(Ti, Sn)O₃(PTS) was selected to compensate the dielectric constant doping of BaTiO₃ since it has high Curie temperature (Tc) point that is about 296 °C. The Curie temperature (Tc) point of BaTiO₃ was broadened and shifted to higher temperature because of the doping of PTS, so the temperature coefficient of capacitance (TCC) curves of the ceramics based on BaTiO₃ was flattened. When 2 wt% Pb(Ti_0.55Sn_0.45)O₃ was added, the sample showed super dielectric properties that the dielectric constant was >1750 at 25 °C, dielectric loss was lower than 2.0% and TCC was <±10% from −55 °C to 200 °C. Therefore the materials satisfied EIA X9R specifications.     

Thermo-optic properties of TiO2, Ta2O5 and Al2O3 thin films for integrated optics on silicon

The direct measurement of the thermo-optic coefficients of aluminium oxide, tantalum pentoxide and titanium dioxide thin films is presented. Using ellipsometry on monolithically integrated permutations of the layers of silicon, silicon dioxide and the material under test, allows the direct measurement of the overall thermo-optic coefficient accounting for thermally induced changes in the dielectric permittivity and density of the materials as well as the elasto-optic effect due to the non-matching thermal expansion coefficients of the different materials.     

Microstructure and magnetic properties of BaTiO3-(Ni,Zn)Fe2O4 multiferroics

The microstructures of composite xBaTiO₃-(1−x)(Ni_0.5Zn_0.5)Fe₂O₄ (BT-NZF) multiferroics with various mixing ratios (x = 0.50, 0.60 and 0.70) are investigated by means of electron backscatter diffraction (EBSD) and magnetic force microscopy (MFM). The EBSD measurements reveal a change in the texture of the ferrite and the BaTiO₃ grains upon increasing the ferrite content in the sample. The sample with x = 0.70 exhibits the best ferrite texture, where only some directions are present. Furthermore, the resulting grain sizes vary from several µm (x = 0.50) to about 100 nm in the sample with x = 0.70. The MFM images reveal the presence of magnetic domains being extended over several adjacent grains, which according to the EBSD data may comprise different crystallographic orientations. In this way, we can explain the differences in the magnetic contrast obtained.     

The study on electrical behavior of Gd2O3-WO3 complex ceramics at high temperature

Gd₂O₃-WO₃ complex ceramics are fabricated by the conventional solid-state reaction process. The electrical characteristics and dielectric properties of the samples were measured at various ambient temperatures in a low electric field (E < 150 V/mm). As the temperature increases, the dielectric constant and the loss tangent show an obvious change at about 50 °C and 330 °C. When the temperature is above 200 °C, the samples display stable nonlinear electrical properties characterized by semiconductivity, and the nonlinearity increases along with increasing temperature. XRD analysis reveals that Gd₂W₂O₉ is the main phase and Gd₂O₃ is the secondary phase. Based on the phase transition of tungsten trioxide, these electrical properties of Gd₂O₃-WO₃ complex ceramics can be simply explained.     

Preparation and dielectric properties of BaCu(B2O5)-doped SrTiO3-based ceramics for energy storage

BaCu(B₂O₅) (BCB) was used as sintering aids to lower the sintering temperature of multi-ions doped SrTiO₃ ceramics effectively from 1300 °C to 1075 °C by conventional solid state method. The effect of BCB content on crystalline structures, microstructures and properties of the ceramics was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and dielectric measurements, respectively. The addition of BCB enhanced the breakdown strength (BDS) while did not sacrifice the dielectric constant. The enhancement of BDS should be due to the modification of microstructures, i.e., smaller and more homogeneous grain sizes after BCB addition. The dielectric constant of BCB-doped ceramics maintained a stable value with 1.0 mol% BCB, which was dominated by the combination of two opposite effects caused by the presence of second phases and the incorporation of Cu²⁺ and Ba²⁺, while further increase was owing to the increase of dissolved Ba²⁺ ions when the content of BCB is more than 2.0 mol%. The multi-ions doped SrTiO₃ ceramics with 1.0 mol% BCB addition showed optimal dielectric properties as follows: dielectric constant of 311.37, average breakdown strength of 28.78 kV/mm, discharged energy density of 1.05 J/cm³ and energy efficiency of 98.83%.     

Synthesis, structure and exchange bias in Cr2O3/CrO2/Cr2O5 particles

We report on the synthesis, structure and magnetic properties of a novel exchange bias system with Cr₂O₃/CrO₂/Cr₂O₅ interfaces. Chromium oxide particles with mixed chromium valences were prepared by sintering CrO₃ in air. X-ray diffraction patterns show that CrO₃ lost its oxygen gradually with increasing temperature and time through Cr₃O₈, Cr₂O₅, CrO₂, and finally Cr₂O₃ at temperatures above 760 K. X-ray photoelectron spectra indicate a low CrO₂ content and a binding energy of 579.3 eV for Cr 2p_3/2 photoelectrons in Cr₂O₅. Chromium dioxide was found to stably coexist with Cr₂O₃ and Cr₂O₅ in the particles. Magnetic measurements show hysteresis loop shifts in the sample, indicating an exchange bias induced by antiferromagnetic Cr₂O₃/Cr₂O₅ in ferromagnetic CrO₂. An exchange bias of 9 mT at 5 K and a coercivity of 26.3 mT were observed in the chromium oxide particles containing CrO₂.     

Low temperature solid-phase synthesis of tetragonal BaTiO3 powders and its characterization

We report an alternative synthesis route for tetragonal and submicron barium titanate particles through a low temperature isothermal heat treatment of a precursor powder obtained from the BaO₂-TiO₂-C mixture utilizing combustion synthesis technique. Effort has been concentrated on the investigation and optimization of the synthesis process including combustion temperature and velocity, heat treatment procedure, and the characteristics of the powder obtained. It was shown that precursor powder prepared by the combustion method easily transformed to the tetragonal BaTiO₃ starting from 700 °C. Characterization of the products was performed by powder X-ray diffraction, scanning electron microscopy (SEM) and BET. From the results, it has been found that the formation of tetragonal BaTiO₃ powder at low temperature is conditioned by high chemical activity and specific characteristics of combustion products. The BaTiO₃ specimens were found to possess high dielectric constant and low dissipation factor at room temperature.