Synthetic spinels of the system MgO-Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Synthetic spinels of the system MgO-Cr₂O₃-Al₂O₃-Fe₂O₃ are considered and the desirability of organizing their production for the refractory industry is demonstrated. Translated from Novye Ogneupory, No. 6, pp. 32–35, June 2008.     

A semiempirical study of CO<Subscript>2</Subscript> elimination in cationic polymerization of cyclic carbonates

The reaction paths of 1,3-dioxan-2-one during cationic ring-opening polymerization have been explored by AM1 semiempirical calculations. A species evolution diagram has been established, and the propagation chain ends on the ether-oxygen of carbonyl functional groups have been identified as the species that ultimately lead to decarboxylation. Three measures were proposed to reduce the degree of decarboxylation based on theoretical calculations: increasing the monomer concentration; decreasing the solvent polarity; and altering the ring substituents so as to bypass the decarboxylation route. Experimental investigations on a number of substituted DOO (including 4-vinyl-1,3-dioxan-2-one and its derivatives) support this conclusion.     

Phase cooperation of V<Subscript>2</Subscript>O<Subscript>5</Subscript> and Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> in the selective oxidation of H<Subscript>2</Subscript>S containing ammonia and water

The selective oxidation of hydrogen sulfide containing excess water and ammonia was studied over vanadium oxide-based catalysts. The investigation was focused on the role of V₂O₅, and phase cooperation between V₂O₅ and Bi₂O₃ in this reaction. The conversion of H₂S continued to decrease since V₂O₅ was gradually reduced by treatment with H₂S. The activity of V₂O₅ was recovered by contact with oxygen. A strong synergistic phenomenon in catalytic activity was observed for the mechanically mixed catalysts of V₂O₅ and Bi₂O₃. Temperature-programmed reduction (TPR) and oxidation (TPO) and two bed reaction tests were performed to explain this synergistic effect by the reoxidation ability of Bi₂O₃. This paper is dedicated to Professor Wha Young Lee on the occasion of his retirement from Seoul National University.     

Influence of composition and temperature on the band gap of glassy melts As<Subscript>2</Subscript>S<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>S<Subscript>3</Subscript>

The edge absorption of glassy melts of the As-Sb-S system are investigated in the temperature interval 77–300 K. It is shown that the temperature dependence of the fundamental absorption edge is described by an exponential function of the photon energy. The temperature and concentration dependences of the optical band gap of glasses of the (As₂S₃)_{100 − x} · (Sb₂S₃) _x section are found. The known Varshni relation is used to describe the temperature dependence.     

Europium(II) in glasses of the Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript>-MnO-Eu<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Triply and doubly charged states of europium are revealed by ¹⁵¹Eu Mössbauer spectroscopy in the structure of glasses of the composition (mol %) 19.5Al₂O₃, 31.5SiO₂, 26.5MnO, and 22.5Eu₂O₃. The isomer shifts in the Mössbauer spectra of Eu³⁺ and Eu²⁺ ions in the structure of glasses differ from the isomer shifts in the spectra of the Eu₂O₃ and EuO compounds. This difference is explained by the fact that the electron density at ¹⁵¹Eu nuclei is affected by the manganese and aluminum atoms, which are not bound directly to the europium atoms. The broadening of the spectra of the Eu²⁺ ions in glasses is caused by the nonuniform isomer shift.     

Low-temperature anti-icing reagents in the Ca(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-Mg(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-CO(NH<Subscript>2</Subscript>)<Subscript>2</Subscript>-H<Subscript>2</Subscript>O system and their properties

The polytherms of ice melting in sections of the Ca(NO₃)₂-Mg(NO₃)₂-CO(NH₂)₂-H₂O system with different component ratios were studied in the temperature interval from 0 to −40°C. A series of nitrate and nitrate-carbonate reagents that are promising for the creation of anti-acing reagents were found, which form eutectics with ice at temperatures from −25 to −39°C. Their properties, viz., melting properties with respect to ice and corrosiveness on metals and alloys, were determined. An effective corrosion inhibitor was selected.     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and CeO<Subscript>2</Subscript>-promoted MgO sorbents for CO<Subscript>2</Subscript> capture at moderate temperatures

A series of Al₂O₃ and CeO₂ modified MgO sorbents was prepared and studied for CO₂ sorption at moderate temperatures. The CO₂ sorption capacity of MgO was enhanced with the addition of either Al₂O₃ or CeO₂. Over Al₂O₃-MgO sorbents, the best capacity of 24.6 mg- CO₂/g-sorbent was attained at 100 °C, which was 61% higher than that of MgO (15.3 mg-CO₂/g-sorbent). The highest capacity of 35.3 mg-CO₂/g-sorbent was obtained over the CeO₂-MgO sorbents at the optimal temperature of 200 °C. Combining with the characterization results, we conclude that the promotion effect on CO₂ sorption with the addition of Al₂O₃ and CeO₂ can be attributed to the increased surface area with reduced MgO crystallite size. Moreover, the addition of CeO₂ increased the basicity of MgO phase, resulting in more increase in the CO₂ capacity than Al₂O₃ promoter. Both the Al₂O₃-MgO and CeO₂-MgO sorbents exhibited better cyclic stability than MgO over the course of fifteen CO₂ sorption-desorption cycles. Compared to Al₂O₃, CeO₂ is more effective for promoting the CO₂ capacity of MgO. To enhance the CO₂ capacity of MgO sorbent, increasing the basicity is more effective than the increase in the surface area.

Open image in new window

     

Phase equilibria in the Ho<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> system

The phase formation is investigated and the phase diagram of the Ho₂O₃-SrAl₂O₄ system is constructed. A ternary compound, namely, Ho₂SrAl₂O₇, is revealed. It is established that this compound undergoes incongruent melting.     

Local crystallization of glasses in the La<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript> system under laser irradiation

A method is proposed for local crystallization of glasses under laser irradiation. This method makes it possible to nucleate and grow microcrystals with a size distribution similar to a monodisperse distribution for several fractions of a second in any glass region chosen in advance. It is demonstrated using glasses in the La₂O₃-B₂O₃-GeO₂ system as an example that the crystallization of the stillwellite-like phase LaBGeO₅ with the composition close to the composition of the initial glass is observed in the glass under irradiation with the copper vapor laser operating in the high-speed pulse modulation mode. Strips (up to ～300 μm) produced at a specified depth from the glass surface contain extended regions consisting of uniformly distributed crystals, which have almost identical sizes, exhibit a pronounced faceting, and are identified using X-ray diffraction. The size and the number of crystals can be changed over a wide range by varying laser treatment conditions. This opens up the way to the design of new glass-ceramic materials in which the location of the crystalline phase in the glass bulk is controlled by a developer.     

Synthesis and properties of flux-cast refractories in the Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-MgO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Details are given of the synthesis and testing of flux-cast refractory materials in the alumina-rich region of the Al₂O₃-MgO-B₂O₃ system; XRD and petrography indicate that the main structure-forming phases are corundum and magnesian spinel. In subordinate amounts there are the boroaluminate 9Al₂O₃·2B₂O₃ and the previously unknown compound 4Al₂O₃·MgO·2B₂O₃, whose composition has been established by microprobe analysis. Corrosion tests showed that three-component systems containing magnesium and boron oxides at levels of 5–10% do not increase the corrosion resistance of refractories in molten sodium-calcium-silicate glass and electrovacuum borosilicate glass. __________ Translated from Novye Ogneupory, No. 3, pp. 161–163, March, 2008.     

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

Phase Equilibria in the Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> System

The phase equilibria are investigated and the phase diagram is constructed for the Gd₂O₃-SrAl₂O₄ pseudobinary join of the Gd₂O₃-SrO-Al₂O₃ ternary oxide system. One ternary compound, namely, Gd₂SrAl₂O₇, is revealed in the Gd₂O₃-SrAl₂O₄ join. It is found that this compound undergoes congruent melting.     

Preparation of CuO-CeO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst with mesopore structure for water gas shift reaction

The water gas shift (WGS) reaction has been investigated widely in fuel cell technologies due to the potential for high fuel efficiency and lower emissions during the production of pure hydrogen. Industrially, the WGS reaction occurs in one of the following two ways: (a) high-temperature in the range of 310–450°C with Fe-Cr catalyst, (b) low-temperature in the range of 210–250°C with Cu-ZnO-Al₂O₃. In this study, a mesoporous catalyst was prepared, with a large surface area and uniformity in both pore size and distribution, by using a one-pot synthesis method. The prepared CuO-CeO₂-Al₂O₃ brought high CO conversion (82%), and was suitable for WGS reaction at low temperature (250 °C). This article is dedicated to Professor Chang Kyun Choi for celebrating his retirement from the School of Chemical and Biological Engineering, Seoul National University.     

Electrical conductivity of CuI-AsI<Subscript>3</Subscript>-As<Subscript>2</Subscript>Se<Subscript>3</Subscript> and CuI-SbI<Subscript>3</Subscript>-As<Subscript>2</Subscript>Se<Subscript>3</Subscript> chalcogenide films prepared by chemical deposition

The electrical conductivity of chalcogenide semiconductor films in the CuI-AsI₃-As₂Se₃ and CuI-SbI₃-As₂Se₃ systems, which have been prepared by chemical deposition from mono-n-butylamine, has been studied as a function of the temperature and film composition. It has been established that the electrical conductivity of the CuI-AsI₃-As₂Se₃ and CuI-SbI₃-As₂Se₃ films is predominantly determined by the copper iodide content. It has been demonstrated that the electrical properties of the chalcogenide glasses and the related films are characterized by the same values to within the experimental error, which is explained by the same model of dissolution of vitreous semiconductors in amines with the retention of the electrical properties of chalcogenide glasses after the deposition of films from their solutions.     

Study on the properties of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-BaO lead-free glass using in the electronic pastes

The Sb₂O₃ doping lead-free glass in Bi₂O₃-B₂O₃-BaO ternary system were prepared in the composition of several different subsystem, and the glass powder was produced through the process of water quenching. Glass transition temperatures (T _g ), glass soften temperatures(T _s ), the volume resistivity (ρ) in the temperature range of 80–200°C, and linear thermal coefficients of expansion in the temperatures range of 25–300°C (α_25–300) were measured for subsystems along with the different ratio of Bi₂O₃, B₂O₃ and BaO. For these subsystems, T _g ranged from 458 to 481°C, and T _s ranged from 490 to 512°C, both decreasing with the increasing of Bi₂O₃/B₂O₃ ratio, and increasing with the increasing of BaO/B₂O₃ ratio. The measured α_25–300 ranged from 65.3 to 76.3 × 10⁻⁷ K⁻¹, with values increasing with increasing Bi₂O₃/B₂O₃ and BaO/B₂O₃ ratio. The volume resistivity remains at a high standards, which may caused by it’s non-alkali composition, and it fluctuated from 10¹³ to 10¹¹ Ω cm with the temperature varied from 80–200°C. The structure of Bi₂O₃-B₂O₃-BaO ternary leadfree glass system was mearsured by FT-IR. The IR studies indicate that these glasses are made up of [BiO₆], [BO₃], and [BO₄] basic structural units, and it appears that Ba²⁺ acts as a glass-modifier in this ternary system, but the Bi³⁺ has entered the glass network when it is in relative high content so as to change the α_25–300, T _s and T _g .     

Mechanism of formation of the complex oxide Na<Subscript>2</Subscript>Nd<Subscript>2</Subscript>Ti<Subscript>3</Subscript>O<Subscript>10</Subscript>

The processes of phase formation in the Nd₂O₃-TiO₂-Na₂CO₃ system have been investigated in the temperature range 500–1100°C. The mechanism of the high-temperature solid-phase reaction of formation of the complex oxide Na₂Nd₂Ti₃O₁₀ has been studied. It has been established that the Na₂Nd₂Ti₃O₁₀ compound is formed from the intermediate product Na_0.5Nd_0.5TiO₃ with a perovskite structure in the temperature range 830–890°C and from the NaNdTiO₄ oxide with a perovskite-like layered structure in the temperature range 960–1100°C.     

Influence of operating temperature on CO<Subscript>2</Subscript>-NH<Subscript>3</Subscript> reaction in an aqueous solution

Although aqueous ammonia solution has been focused on the removal of CO₂ from flue gas, there have been very few reports regarding the underlying analysis of the reaction between CO₂ and NH₃. In this work, we explored the reaction of CO₂-NH₃-H₂O system at various operating temperatures: 40 °C, 20 °C, and 5 °C. The CO₂ removal efficiency and the loss of ammonia were influenced by the operating temperatures. Also, infrared spectroscopy measurement was used in order to understand the formation mechanism of ion species in absorbent, such as NH₂COO⁻, HCO₃⁻, CO₃²⁻, and NH₄⁺, during CO₂, NH₃, and H₂O reaction. The reactions of CO₂-NH₃-H₂O system at 20 °C and 40 °C have similar reaction routes. However, a different reaction route was observed at 5 °C compared to the other operating temperatures, showing the solid products of ammonium bicarbonates, relatively. The CO₂ removal efficiency and the formation of carbamate and bicarbonate were strongly influenced by the operating temperatures. In particular, the analysis of the formation carbamate and bicarbonate by infrared spectroscopy measurement provides useful information on the reaction mechanism of CO₂ in an aqueous ammonia solution.