Depth profiling of Al2O3 + TiO2 nanolaminates by means of a time-of-flight energy spectrometer

Atomic layer deposition (ALD) is currently a widespread method to grow conformal thin films with a sub-nm thickness control. By using ALD for nanolaminate oxides, it is possible to fine tune the electrical, optical and mechanical properties of thin films. In this study the elemental depth profiles and surface roughnesses were determined for Al₂O₃ + TiO₂ nanolaminates with nominal single-layer thicknesses of 1, 2, 5, 10 and 20 nm and total thickness between 40 nm and 60 nm. The depth profiles were measured by means of a time-of-flight elastic recoil detection analysis (ToF-ERDA) spectrometer recently installed at the University of Jyväskylä. In TOF-E measurements ⁶³Cu, ³⁵Cl, ¹²C and ⁴He ions with energies ranging from 0.5 to 10 MeV, were used and depth profiles of the whole nanolaminate film could be analyzed down to 5 nm individual layer thickness.     

Application of combined neutron diffraction and impedance spectroscopy for in-situ structure and conductivity studies of La2Mo2O9

In-situ neutron diffraction combined with AC impedance spectroscopy was applied successfully to investigate the correlation between crystal structure and electrical properties of the La₂Mo₂O₉ oxide ion conducting electrolyte material. Neutron diffraction patterns were collected as a function of temperature while the AC impedance spectra were recorded simultaneously using a modified sample environment to monitor the conductivity change of the sample. A close relationship between unit cell parameters and the bulk conductivity was observed, confirming that the oxygen transport is dependent on the lattice structure. With the transition from the low temperature alpha to the high temperature beta phase, expansion of the crystal structure makes more space available for oxygen transport, leading to a dramatic increase of the ionic conductivity. The successful application of this technique provides a new method to simultaneously investigate crystal structure and electrical properties in electro-ceramics in the future.     

烧绿石(La1-yNdy)2Zr2O7模拟固化241Am的晶体结构稳定性研究

为研究²⁴¹Am在La₂Zr₂O₇烧绿石中的固化行为及其对烧绿石晶体结构稳定性的影响,实验选用Nd作为²⁴¹Am的模拟物,采用Sol-喷雾热解法合成了(La_1-yNd_y)₂Zr₂O₇（0.0≤y≤1.0）系列样品,并借助X射线衍射和振动光谱手段对样品的晶体结构稳定性进行了研究。实验结果表明：随着Nd掺杂量的增加,O48f位置参数x_48f和I₍₁₁₁₎ /I₍₂₂₂₎均呈规律性增大,Raman谱逐渐展宽,IR谱发生蓝移,所有结果均证实用Nd不断替换La将导致烧绿石晶体结构有序化程度逐渐降低。另外,实验发现掺杂量y≈0.8是烧绿石晶体结构发生几何相变的逾渗阈值,超过该阈值有序的烧绿石结构将发生突变进而加速向无序萤石结构转变,该实验结果可为(La_1-yAm_y)2Zr2O7固溶体的结构稳定性研究提供参考。     

Study of the magnetic modifications of Fe3O4 ferrite thin films induced by 2.03 GeV Kr ions irradiation

The effect of 2.03 GeV Kr²⁶⁺ ions irradiation on antiphase boundaries (APBs) of polycrystalline Fe₃O₄ ferrite thin films has been investigated. The structure, magnetic and electrical transport properties of samples were characterized. The initial crystallographic structure of the Fe₃O₄ remains unaffected after Kr-ion irradiation, but the magnetic and electrical transports properties are sensitive to swift heavy ions (SHI) irradiation and exhibit different behaviors depending on the Kr-ion fluence range. The energy deposition is mainly due to the electronic energy loss (S_e) and the large value of energy transferred induces an unusual density of defects, stress and heat annealing effect in the samples, which can affect on the arrangement of magnetic moments and APBs density strongly. On the basis of our observations we conclude that the production, accumulation and free of the defects and stress induced by SHI irradiation is more dominant in the case of the magnetic and electrical transport properties modifications of the Fe₃O₄ thin films.     

Ion guiding through capillaries in uncoated Al2O3 membranes

We made an experimental study on ion guiding through capillaries in uncoated Al₂O₃ membranes using a variety of ions such as O¹⁺, O³⁺, and O⁶⁺. The incident energy was varied within the range of 30-150 keV. The results were compared with others using coated PET and Al₂O₃ capillary membranes as well as with the so-called scaling law discovered by Stolterfoht and his co-workers. Good agreement of our results with the scaling law was found. However, our membranes showed extraordinarily strong guiding ability. The reason lies in that our membranes were uncoated. A slower charge drift speed along the insulating capillary wall and a much larger equilibrium charge Q_∞ seems to exist in our experiment.     

Study on effects of swift heavy ion irradiation on the crystal structure in CeO2 doped with Gd2O3

To simulate the effects of Gd₂O₃-doping and high-energy fission products in UO₂, Gd₂O₃-doped CeO₂ pellets were irradiated with 200-MeV Xe¹⁴⁺ ions. Doping and irradiation effects were analyzed using X-ray diffraction (XRD) and extended X-ray absorption fine structure (EXAFS). The lattice constant of CeO₂ decreases and the local structure is disordered with increased doping levels. However, the irradiation induces an expansion of the lattice and a disordering of atomic arrangement near the Gd atoms. The effects of the irradiation become more pronounced with increasing Gd₂O₃-dopant levels. Our results are compared with those of a study involving Er₂O₃-doped CeO₂.     

Nanostructuring of BaF2 (1 1 1) surfaces by single slow highly charged ions

The creation of surface nanostructures in BaF₂ (1 1 1) surfaces was studied after irradiation with slow highly charged Xe ions from the Dresden-EBIT (electron beam ion trap). After irradiation, the crystals were investigated by scanning force microscopy (SFM). Using specific ion parameters, the topographic images show nanohillocks emerging from the surface. Additionally, we used the technique of selective chemical etching to reveal the lattice damage created by ion energy deposition below and above threshold needed for surface hillocks formation. The role of both potential and kinetic energy as well as a comparison with results for swift heavy ion irradiations of BaF₂ single crystals are presented.     

Effects of swift heavy ion irradiation on the structure of Er2O3-doped CeO2

In order to simulate the effects of burnable poison doping on the fission fragment damage of UO₂ nuclear fuels, Er₂O₃-doped CeO₂ pellets were irradiated with 200 MeV Xe¹⁴⁺ ions. The irradiation effect was measured by means of X-ray diffraction (XRD). The expansion of lattice and the disordering of atomic arrangement due to the irradiation become more remarkable with increasing the concentration of the Er₂O₃ dopant.     

Electronic sputtering of Gd3Ga5O12 and Y3Fe5O12 garnets: Yield, stoichiometry and comparison to track formation

The results of present paper have shown that sputtering of yttrium iron garnet (Y₃Fe₅O₁₂) under swift heavy ions in the electronic energy loss regime is non-stoichiometric. Here we are presenting additional experimental results for gadolinium gallium garnet (Gd₃Ga₅O₁₂) as target. The irradiations were performed with different ions (⁵⁰Cr (589 MeV), ⁸⁶Kr (195 MeV) and ¹⁸¹Ta (400 MeV)) impinging perpendicularly to the surface. As earlier, the sputtering yield was determined by collecting the emitted gadolinium and gallium atoms on a thin aluminium foil, placed upstream above the target and analyzing the Al catcher by Rutherford backscattering. Also for Gd₃Ga₅O_12, the emission of Gd and Ga is non-stoichiometric. Sputtering appears above a critical electronic stopping power of S_th = 11.6 ± 1.5 keV/nm, which is larger than the threshold for track formation, in agreement with other amorphisable materials. In addition, the angular distribution of the sputtered species was measured for Y₃Fe₅O₁₂ and Gd₃Ga₅O₁₂ using 200 MeV Au ions impinging the surface at 20° relatively to the surface. For the two garnets the ratio of Y/Fe (and Gd/Ga) varies with the angle of emitted species and the stoichiometry seems to be preserved only for an emission perpendicular to the surface.     

γ辐照联合H_2O_2处理污泥滤液的研究

采用60 Coγ射线辐照处理污泥滤液,通过对比处理前后化学需氧量(COD)、紫外可见吸光度和浑浊度的变化,研究了辐照处理中初始pH、初始H2O2浓度和吸收剂量对污泥滤液处理效果的影响。结果表明:在相同吸收剂量和初始H2O2浓度条件下,酸性条件更利于CODCr的降低;γ辐照联合H2O2处理存在显著协同效应,吸收剂量为18.75kGy、初始H2O2浓度为2mmol/L时,污泥滤液CODcr去除率达70.4%,浑浊度下降94.9%。     

Nanoparticles of Al2O3:Cr as a sensitive thermoluminescent material for high exposures of gamma rays irradiations

Aluminum Oxide (Al₂O₃) doped with proper activators is a highly sensitive phosphor commonly used for radiation dosimetry using thermoluminescence (TL) technique. Nanoparticles of this material activated with Chromium (Cr) have been synthesized using the propellant chemical combustion technique and studied for their TL response. They were characterized by X-ray diffraction and scanning electron microscope. The synthesized material has spherical nanoparticles with grain size around 25 nm. These nanoparticles were exposed to heavy doses from γ-rays of ¹³⁷Cs. The TL glow curves show a prominent peak at around 474 K. This peak is found to be sensitive for high exposures of γ-rays and has linear response in the range of 100 Gy-20 kGy without showing saturation. This remarkable result suggests that Al₂O₃:Cr nanoparticles might be used for the dosimetry of food and seed irradiations.     

6 MeV electron irradiation effects on electrical properties of Al/TiO2/n-Si MOS capacitors

The irradiation effects of 6 MeV electrons on the electrical properties of Al/TiO₂/n-Si metal-oxide-semiconductor capacitors have been investigated. Nine Al/TiO₂/n-Si capacitors were fabricated using radio frequency magnetron sputtering and divided into three groups. Groups were irradiated with 6 MeV electrons at 10, 20, and 30 kGy doses, respectively, keeping the dose rate ∼1 kGy/min. The variations in the capacitance-voltage and leakage current-voltage characteristics, in addition to the electrical parameters, such as conductance (G/ω), flat-band voltage, interface trap density and the surface charge density with electron dose were studied. The Poole-Frenkel coefficient of the MOS capacitors was determined from current-voltage characteristics. Possible mechanisms for the enhanced leakage current in the electron irradiated MOS capacitors are discussed.     

Growth of TiO2 surfaces following low energy (<40 eV) atom and small cluster bombardment

Low energy (10-40 eV) interaction of small Ti_xO_y clusters with a rutile (1 1 0) substrate was investigated using molecular dynamics with the aim of determining the influence of various parameters on surface growth and defect formation. Rutile growth was simulated through depositing randomly selected clusters with energies in the tens of eV range. Long time scale evolution was approximated through heating the substrate. A modified second-moment-Buckingham-QEq (SMB-Q) empirical potential was developed for the purpose. Crystal growth on amorphous and anatase TiO₂ substrates was also considered. Grown lattice layers were compared by visual inspection along with radial distribution function (RDF) plots. Bombardment at an energy of around 20 eV in an oxygen rich atmosphere with a high proportion of bombarding clusters, TiO, TiO₂, as opposed to single atoms, was found to produce rutile growth with the best crystallinity.     

Ion beam analysis of partial lithium extraction of LiMn2O4 by chemical delithiation

Lithium manganese oxide, LiMn₂O₄, has been studied by many research groups. This material is a great candidate to be used as positive electrode in rechargeable lithium-ion batteries because of its low cost, abundant precursors and non-toxicity. LiMn₂O₄ has a spinel Fd-3m structure and shows a reversible extraction and insertion of lithium ions that is one of the most important characteristic of positive electrodes in rechargeable batteries.In this work, LiMn₂O₄ samples were synthesized by solid state reaction. A partial lithium removal was performed on this system by chemical delithiation using HCl aqueous solutions at different concentrations. Six partial-extracted compounds were obtained and characterized by Ion beam analysis (IBA) in order to obtain the Li concentrations. X-ray diffraction (XRD) and Rietveld analyses were also performed. A rigorous study of lithium contents is critical to analyze the structure properties of these compounds and samples production parameters. The IBA method used in this work was the analysis of energy spectra of elastic backscattered (EBS) proton from Mn, O and Li nuclei and the α-particles energy from the ⁷Li(p,α)⁴He nuclear reaction (NR).     

Frequency dependence studies on the interface trap density and series resistance of HfO2 gate dielectric deposited on Si substrate: Before and after 50 MeV Li ions irradiation

We report the first investigation of the frequency dependent effect of 50 MeV Li³⁺ ion irradiation on the series resistance and interface state density determined from capacitance-voltage (C-V) and conductance-voltage (G-V) characteristics in HfO₂ based MOS capacitors prepared by rf-sputtering. The samples were irradiated by 50 MeV Li³⁺ ions at room temperature. The measured capacitance and conductance were corrected for series resistance. The series resistance was estimated at various frequencies from 1 KHz to 1 MHz before and after irradiation. It was observed that the series resistance decreases from 6344.5 to 322 Ω as a function of frequency before irradiation and 8954-134 Ω after irradiation. The interface state density D_it decreases from 1.12 × 10¹² eV⁻¹ cm⁻² before irradiation to 3.67 × 10¹¹ eV⁻¹ cm⁻² after ion irradiation and further decreases with increasing frequency.     

Treatment of UO2 pellets used for preparing fuel elements of HTR-10 followed by supercritical fluid extraction

International interest in high temperature gas-cooled reactor (HTGR) has been increasing in recent years. It is important to study on reprocessing of spent nuclear fuel from HTGR for recovery of nuclear resource and reduction of nuclear waste. Treatment of UO₂ pellets used for preparing fuel elements of the 10 MW high temperature gas-cooled reactor (HTR-10) followed by supercritical fluid extraction was investigated. When UO₂ pellets were dissolved and extracted with tri-n-butyl phosphate (TBP)–HNO₃ complex in supercritical CO₂ (SC-CO₂), the extraction efficiency was less than 7% under experimental conditions. After UO₂ pellets were ground into UO₂ fine powders, the extraction efficiency of the UO₂ fine powders with TBP–HNO₃ complex in SC-CO₂ could reach 92%. After UO₂ pellets broke spontaneously into U₃O₈ powders under O₂ flow and 600 °C, the extraction efficiency of the U₃O₈ powder with TBP–HNO₃ complex in SC-CO₂ could reach more than 98%.     

α/γ相比率调控对超音速等离子喷涂Al2O3阻氚涂层微结构及性能的影响

采用超音速等离子喷涂技术在中国低活化马氏体钢表面制备不同α/γ相比率的Al₂O₃阻氚涂层,研究了α/γ相比率调控对Al₂O₃涂层微观结构、力学性能和耐电化学腐蚀性能的影响。利用掠入射X射线衍射（GIXRD）和扫描电子显微镜（SEM）表征Al₂O₃涂层的微观结构、粘结拉伸试验法和纳米压痕仪表征涂层的力学性能、动电位极化曲线法测试涂层的耐电化学腐蚀性能。研究结果显示：通过调控特征喷涂参数（CPSP）,Al₂O₃涂层中α相含量从78.6%至24.4%可控调节,且孔隙率从2.8%降低至1.5%;α相含量为78.6%的Al₂O₃涂层硬度为(11.500±0.575) GPa,约为高γ相含量(75.6%)涂层的2倍;且高α相含量(78.6%)涂层的腐蚀电流密度较高γ相含量(75.6%)涂层的腐蚀电流密度低1个数量级。以上结果表明,高α相含量(78.6%)的Al₂O₃涂层具有更优异的力学性能、耐电化学腐蚀性能以及耐Cl^-扩散穿透能力,具有应用于聚变堆结构材料表面阻氚涂层的潜能。