CASS工艺生物脱氮除磷效果分析

对CASS工艺脱氮除磷效果进行了试验研究,重点研究了温度和回流比对脱氮效果的影响,曝气量对除磷效果的影响。研究结果表明,水温在30℃时系统脱氮效果最好,此时NH3-N去除率在80%左右,TN去除率在70%左右;污泥回流比为25%、50%、100%和200%时,TN去除率分别为50%、58%、62%和70%,增加回流比可以提高脱氮效率;好氧区DO维持在2mg/L和4 mg/L时,TP去除率分别为82%和37%。     

采用UCT工艺的复合式MBR脱氮除磷影响研究

采用UCT工艺的复合式MBR(HMBR)系统进行污水脱氮除磷试验研究,探讨进水C/N比、系统内回流比r、硝化液回流比R和污泥停留时间对系统脱氮除磷效果的影响。试验结果表明,上述4个因素对采用UCT工艺的HMBR系统的脱氮除磷效果均有影响,在C/N=5～8、r=200%、R=300%、SRT=28 d的条件下,系统脱氮除磷效果最佳,TN平均去除率79.17%,膜出水平均浓度11.78 mg/L;TP平均去除率86.68%,膜出水平均浓度0.71 mg/L。     

生物流化床法处理城市污水处理厂污泥回流液的可行性研究

以城市污水处理厂污泥回流液为研究对象,研究生物流化床法降低污泥回流液中氮磷浓度的效果,并分析了COD/TN与COD/TP值对生物流化床脱氮除磷的影响.结果表明,COD_(Cr)浓度对脱氮影响不大,而对除磷有较大影响.在COD_(Cr)为500 mg/L,进水TN为115 mg/L时,TN的去除率最大为72.05%,此时,COD/TN值为4.35.在COD_(Cr)为480 mg/L,进水TP为11.25 mg/L时,TP的去除率最高为36.98%,此时COD/TP为42.67.生物流化床法对降低高浓度氮磷污泥回流液具有一定的去除效果,TN去除率可达56.35%,TP去除率为28.96%.     

双污泥回流A~2/O工艺在低温下的脱氮除磷效果

在温度为9~16℃的低温条件下,考察了双污泥回流A2/O工艺系统处理低C/N城市污水的脱氮除磷特性。试验结果表明:在低温处理低C/N城市污水时,将A2/O工艺改良为双污泥回流系统,通过富集反硝化除磷菌(DPB)和强化缺氧吸磷等方法,取得了良好的同步脱氮除磷效果。当水温为12~16℃,缺氧池DO为0.2~0.4mg/L时,进水TN、NH3—N和TP平均分别为47.44mg/L、37.50mg/L和6.01mg/L时,系统出水TN、NH3—N和TP平均分别为12.81mg/L、2.75mg/L和0.37mg/L,去除率分别为72.99%、92.66%和93.90%,当水温为9~12℃时,系统对TN、NH3—N和TP去除效果下降,不能达到预定的去除目标。系统对COD去除效果良好,进水COD平均为253.59mg/L,出水为26.85mg/L,平均去除率为89.41%。     

抚顺污水处理厂活性污泥培养驯化与启动调试

抚顺污水处理厂是目前国内外已经投产、规模最大的采用DAT -IAT工艺的城市污水处理厂。在活性污泥培养驯化和启动调试过程中 ,有效地解决了低气温、低水温、进水营养源不足、污泥上浮和设备故障等问题。采用流态连续形方法 ,在平均气温为 6 5℃ ,反应器中水温 11～ 13℃的低温不利条件下 ,成功地进行了DAT -IAT工艺污水处理厂的活性污泥培养驯化和启动调试。培养驯化周期 30d左右 ,活性污泥絮体基本形成。出水BOD为 5 4～ 12 8mg/L ,去除率为 77 6 %～95 2 % ;COD为 39～ 94 5mg/L ,去除率为 2 9 5 %～ 86 3% ;SS为 9～ 19mg/L ,去除率为 6 4 7%～91 5 % ;NH3-N为 2 5～ 3 3mg/L ,去除率为 90 % ;TP为 1 1～ 1 2mg/L ,去除率为 6 4 7%～6 7 6 %。各项出水水质和能耗等指标达到了或优于设计目标。     

内循环生物流化床处理N、P废水的试验研究

采用内循环生物流化床系统,进行N、P废水的试验研究,通过控制曝气时间和溶解氧浓度,能同时达到脱氮除磷的效果.对于N、P废水,COD在352～1048 mg/L,TN在46.9～76.4 mg/L,TP在5.8～14.4 mg/L时,COD、TN、TP去除率分别为92%、80%、93%,处理后的水可达到国家二级排放标准.     

铁阳极电凝聚法除磷条件初探

采用铁板作阳极,白钛网板作阴极的电凝聚方法处理含磷废水。结果表明,极板间距为3cm时,电流效率为88.1%;当原水磷浓度为5mg/L时,最优电流密度为2mA/cm~2;连续通电比只通电45min和25min对磷的去除率分别高10%和40%左右;将电凝聚用于活性污泥混合液中磷的去除,污泥絮体和有机物对电凝聚除磷效果无明显影响,去除率仍达95%以上。电解后污泥沉降性有所改善,SV值从83%降至40%,污泥浓度仅由2.41g/L增至2.47g/L,增幅2.4%。     

溶解氧对低碳源污水一体化处理工艺脱氮除磷的影响

通过试验对比,研究了溶解氧对低碳源污水一体化工艺脱氮除磷效果的影响。结果表明,平均溶解氧为0.18mg/L时,系统出水可以稳定达到GB 18918—2002一级A标准,溶解氧过高或过低都会降低系统脱氮除磷效果。在平均溶解氧为0.18mg/L的工况下,系统存在反硝化吸磷、同时硝化反硝化及全程反硝化3种脱氮方式,且反硝化吸磷和同时硝化反硝化脱氮量占氮总去除量的66.7%,可以较大程度降低脱氮除磷过程所需碳源量并节省耗氧量,提高低碳源污水脱氮除磷效果。     

不同电子受体的反硝化除磷效果对比研究

反硝化除磷作用可以明显节省脱氮除磷过程的碳源需求和能耗。为研究不同电子受体下的反硝化除磷效果,利用一体化活性污泥工艺中污泥经过厌氧释磷后在不同电子受体下进行反硝化除磷试验,结果表明NO3-—N和NO2-—N均能参与反硝化除磷过程,在NO2-—N初始浓度高达30mg/L的条件下,除磷率仍在93%以上,未对反硝化除磷过程产生毒害作用。在工程应用中应加强短程硝化反硝化与反硝化除磷作用的耦合,在提高脱氮除磷效率的同时,取得明显的节能效果。     

传统活性污泥法的脱氮除磷改造实践

在仍使用旧设备和构筑物的基础上 ,对传统活性污泥生物处理工艺进行了改良 ,解决了污泥膨胀问题 ,工艺运行更加稳定 ,而且使氮磷的去除率提高。在脱氮模式中氨氮的去除率达到了73 3% ;除磷模式中 ,总磷的去除率达到了 82 0 % ,大大优化了出水水质     

Denitrification of nitrate-contaminated groundwater using a simple immobilized activated sludge bioreactor

A simple anaerobic-activated sludge system, in which microorganisms are immobilized by a novel functional carrier, was used for removing nitrate in groundwater. The operating conditions, including hydraulic retention time (HRT), C/N ratio, temperature and NO(3)(-)-N loading concentration were investigated. The NO(3)(-)-N concentration, residual chemical oxygen demand (COD) and nitrite accumulation were used as indicators to assess the water quality of the effluent. The anaerobic biomass loading capacity in the carrier was 12.8 g/L and the denitrifying Pseudomonas sp. and Rhodocyclaceae bacterium were dominant among the immobilized microorganisms in the anaerobic-activated sludge. Under operating conditions of HRT= 1.5 h, C/N= 2-3 and T= 16.8-20 °C, the removal efficiency of NO(3)(-)-N exceeded 93%, corresponding to a relatively high denitrification rate of 0.73 kg NO(3)(-)-N m(-3) d(-1), when the NO(3)(-)-N loading concentration was 50 mg/L. The NO(3)(-)-N concentration of the effluent always met regulatory criteria for drinking water (<10 mg/L) in the main developed and developing countries. The effluent COD was also below 10 mg/L. Although some nitrite accumulated (0-1.77 mg/L) during the operating period, it can be decreased through adjusting the operating pH and HRT. The immobilized activated sludge system may be useful for the removal of nitrate from groundwater.     

好氧颗粒污泥脱氮除磷效率研究

以实验室模拟废水为进水,在SBR反应器中利用好氧颗粒污泥进行N、P的去除效率研究.研究表明:在运行周期约为4h,进水COD控制在500～1200 mg/L之间,室温条件下,好氧颗粒污泥对COD、氨氮、硝氮、TP的去除率稳定维持在97％、95％、92％、86％,说明好氧颗粒污泥特有的结构特性和生物特性有利于脱氮除磷.     

Fe3+对活性污泥系统的影响

通过小试研究了微量Fe3+对活性污泥系统的影响.将浓度为3 mg/L,5 mg/L,10 mg/L,20 mg/L,30 mg/L,50 mg/L和80 mg/L的Fe3+分别投加到活性污泥系统中,反应4 h后测定系统出水COD、活性污泥的SVI、脱氢酶活性及其EPS组分.结果表明,Fe3+浓度小于50 mg/L时对活性污泥的脱氢酶活性具有促进作用,浓度为10 mg/L时促进作用最强;Fe3+浓度在80 mg/L以下均具有良好的絮凝作用,浓度在30 mg/L以下时絮凝作用最强.两种作用的共同结果影响系统对COD的去除效果.对活性污泥EPS组分的测定表明,Fe3+的絮凝作用对SVI的影响是主要的.     

沉淀池生物污泥回流工艺生物强化作用的研究

利用生物预处理出水中携带的硝化细菌和异养细菌等微生物,在后续沉淀单元产生生物延伸效应,并通过采取沉淀池生物污泥回流强化措施,使沉淀池在去除浊度的同时,产生类似活性污泥法的作用,强化生物净化作用.在增加生物污泥回流前、后,沉淀池出水CODMn平均分别为4.16mg/L、2.72 mg/L,沉淀池出水相对生物预处理出水CODMn的平均去除率由4.65%提高至31.4%,去除效果显著提高.同时,增加生物污泥回流后,对浊度和氨氮的去除也得到进一步的改善.     

Full scale implementation of the nutrient limited BAS process at S?dra Cell V?r?.

A combination of the suspended carrier biofilm process and the activated sludge process (biofilm-activated sludge--BAS) has been shown to be very successful for the treatment of different types of pulp and paper mill effluents. The robust biofilm pre-treatment in combination with activated sludge results in a stable, compact and highly efficient process. Recent findings have shown that nutrient limited operation of the biofilm process greatly improves the sludge characteristics in the following activated sludge stage, while minimising sludge production and effluent discharge of nutrients. The nutrient limited BAS process was implemented at full scale at the S?dra Cell V?r? kraft mill and taken into operation in July 2002. After start-up and optimisation over about 5 months, the process meets all effluent discharge limits. The removal of COD is close to 70% and the removal of EDTA greater than 90%. Typical effluent concentrations of suspended solids and nutrients during stable operations have been 20-30 mg/L TSS, 0.3-0.5 mg/L phosphorus and 3-5 mg/L nitrogen. The sludge production was 0.09 kgSS/kg COD removed and the sludge volume index was 50-100 mL/g.     

林可霉素高浓度有机废水处理技术

采用厌氧颗粒和好氧活性污泥分别对内循环厌氧反应器(IC)和间歇式活性污泥法(SBR)进行污泥接种培养,研究水解酸化-IC-SBR工艺在林可霉素生产废水处理方面的运行效果。结果表明:在进水COD的质量浓度为6 000~9 000 mg/L,IC和SBR反应器中有机负荷分别为0.82 kg/(kg.d)和0.26 kg/(kg.d)左右的情况下,IC和SBR反应器分别运行60 d和7 d,COD平均去除率分别达到91%和61%,出水COD的质量浓度在300 mg/L以下,达到GB 8978—1996《污水综合排放标准》二级标准。     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Aerobic granulation in a mechanical stirred SBR: treatment of low organic loads

Aerobic granular sludge was produced in a sequencing batch reactor (SBR) characterized by a height to diameter ratio of 2.5 and the use of mechanical stirring. Compact and regular aerobic granules of up to 1.75 mm of average diameter were formed in the reactor with an organic loading rate of 1.75 kg COD/(m3 d). Settling properties of the obtained aggregates were: sludge volumetric index of 30-40 mL/g VSS and settling velocity higher than 8 m/h. The effects of different carbon to nitrogen ratios (TOC/N) in the feeding on the organic matter oxidation and nitrification process were studied. The concentration of organic matter in the feeding was stepwise reduced (from 190.0 to 37.5 mg TOC/L) and ammonium increased (from 25 to 50 mg NH4+ -N/L). TOC/N ratios of 7.50, 3.00, 1.50 and 0.75 g/g in the feeding were tested. The TOC removal percentage was around 80-95% during the whole operational period and the N removal percentages obtained in the reactor were up to 40%, however, physical properties of the granules were not maintained.     

Nitrogen removal from the saline sludge liquor by electrochemical denitrification.

Sludge liquor from the sludge dewatering process has a high ammonia content. In the present study, a lab-scale electrochemical (EC) system with a pair of Ti electrode plates was used for treating the sludge centrate liquor of digested wastewater sludge with a NH4(+) - N content of around 500 mg/L. The sludge liquor had a high salinity due to seawater being used for toilet flushing in Hong Kong. The results show that the EC process is highly effective for denitrification of the saline sludge liquor. Complete nitrogen removal could be achieved within 1 hr or so. The rate of EC denitrification increased with the current intensity applied. The best current efficiency for nitrogen removal was obtained for a gap distance between the electrodes at 8 mm. Electro-chlorination was considered to be the major mechanism of EC denitrification. The formation of chlorination by-products (CBPs) appeared to be minimal with the total trihalomethanes (THM) detected at a level of 300 microg/L or lower. The power consumption for EC denitrification was around 23 kWh/kg N. Additional electro-flocculation with a pair of iron needle electrodes could enhance the flocculation and subsequent sedimentation of colloidal organics in the sludge liquor, increasing the organic removal from less than 30% to more than 70%. Therefore, the EC process including both electro-denitrification and electro-flocculation can be developed as the most cost-effective method for treatment of the saline sludge liquor.     

Phosphorus removal from synthetic and municipal wastewater using spent alum sludge.

In the present study, phosphorus removal was studied using as coagulant spent alum sludge from a water treatment plant of EYDAP (Athens Water Supply and Sewerage Company) and compared to alum (Al2(SO4)3.18H2O), iron chloride (FeCl3.7H2O), iron sulfate (Fe2(S04).10H2O) and calcium hydroxide (Ca(OH)2) at a constant pH (equal to 6).The comparison was based on their efficiency to remove phosphorus in synthetic wastewater consisting of 10 mg/L P as potassium dihydrogen phosphate and 50 mg/L N as ammonium chloride, The experiments were carried out using a jar-test apparatus and the measurements were performed according to the Standard Methods for the Examination of Water and Wastewater. Pure alum, iron chloride and iron sulfate were much more efficient in phosphorus removal than the spent alum sludge but in the case of calcium hydroxide, phosphorus removal was very low in pH = 6. Specifically, orthophosphate were totally removed by alum using 15 mg/L as Al, by alum sludge using 75 mg/L as Al and by FeCl3.7H2O or Fe2(SO4).10H2O using 30 mg/L of Fe while in the case of calcium hydroxide P removal was actually zero. pH measurements showed that the uptake of phosphates is associated to the release of OH ions in the solution and that the end of P uptake is accompanied by the stabilization of pH. Finally this spent alum sludge was tested on municipal wastewater and proved to be effective as apart from phosphorus it was shown to remove turbidity and COD.