Silane coatings with different thicknesses were synthesized on CNFs for reinforcement of polyethylene composites. The thickness of the silane coating was adjusted by using a basic catalyst to increase the overall reactivity of the silane groups, resulting in a thick coating of ≈46 nm (ca. 90% increase in fiber diameter). DMA performed on the polyethylene composites showed a substantial increase in storage modulus from 1.68 to 2.34 GPa (40%) at low temperatures in the composite with the thick silane coating (≈46 nm) at a low loading of 0.4 wt.‐%. We believe that the silane‐treated nanofillers with thick coatings are very promising for high‐performance nanocomposites with non‐polar polymer matrices.
Electrically conductive, cationically UV‐cured composites were prepared using exfoliated graphite plates (EGP) with cycloaliphatic epoxy resin and polyalcohol binder system. Exfoliated graphite (EG) was obtained from natural flake graphite through chemical and thermal treatment. Sonication of EG in solvent produced EGP. Characterization of graphite samples by XRD showed structural similarity between original graphite and EGP. UV curing behavior was characterized using photoDSC. Electrical resistivity measurements of the composites as a function of EGP concentration showed that at low filler concentration the binder system can influence the electrical percolation behavior. Some formulations showed electrical percolation at less than 1 vol.‐% of EGP filler.
EVA copolymer/organoclay nanocomposites were prepared using melt‐compounding. Organoclays were obtained using wet and semi‐wet modification methods. These methods enable us to obtain organoclays with adequate modifier incorporation, but organoclays with a homogeneous and narrow agglomeration size distribution were obtained only with the wet method. TS and EB were higher for nanocomposites obtained with organoclays prepared using the wet method. Analysis of Limiting Oxygen Index, UL94 test and Cone Calorimeter test showed that the retardant properties of nanocomposites were also influenced by the kind of modifiers and the modification method.
The preparation of functional nanocomposites by dispersion of a synthetic lamellar α‐ZrP within a styrene/butadiene random copolymer during melt compounding is described. It is shown how the physical and chemical incompatibility of filler and polymer can be overcome, and problems arising from the low viscosity ratio between slurry and polymer matrix are discussed. The aqueous phase can easily be eliminated at the end of the process. The dispersion of the ZrP requires the use of intercalants, and alkylamines were used for this purpose. XRD and TEM are used to characterize the degree of organization of ZrP in the slurries and in the matrix. DMA helps to understand the origin of the limited reinforcing effect.
Conducting polymer blends based on styrene–butadiene–styrene (SBS) triblock copolymer and polyaniline doped with dodecylbenzene sulfonic acid (Pani.DBSA) were prepared by different procedures: mechanical mixing (MM) and ‘in situ’ polymerization (ISP) methods. The ISP blends exhibited higher levels of electrical conductivity, as compared to MM blends. The scanning electron micrographs of the ISP blend were characterized by the presence of microtubules, which favored the formation of the conducting pathways inside the SBS matrix. From dynamic mechanical and dielectric analysis, it was possible to suggest a higher interaction degree of the polyaniline with the polystyrene phase of the block copolymer. Blends prepared by ISP method displayed also higher dielectric constant and higher dielectric loss factor than blends prepared by MM method.
NR/GE composites were prepared by an ultrasonically‐assisted latex mixing and in situ reduction process. Graphene oxide was dispersed in NRL using an ultrasonic field and was then reduced in situ, followed by latex coagulation to obtain the NR/GE masterbatch. The results show that the process produces a much better dispersion and exfoliation of GE in the matrix and contributes to an increase in the tensile strength compared to conventional direct mixing. Compared to pure rubber, the tensile strength and tear strength for NR/(2 wt.‐%)GE composites were increased by ≈47 and 50%, respectively. With increasing GE content, the maximum torque, crosslink density, elastic modulus, and thermal conductivity of NR/GE composites were found to increase.
DSC indicated that the nucleation of PLLA is enhanced in the presence of PGA even at a PGA content as low as 0.1 wt.‐%. However, the enhancing behavior of PGA was different to that of other nucleating agents for PLLA. Polarized optical microscopy revealed that the presence of PGA increased the number of PLLA spherulites per unit area. WAXD showed that in the PLLA/PGA films, PLLA and PGA crystallize separately to form their respective crystallites and PGA crystallites were formed at a PGA content at above 3 wt.‐% (at least). FTIR spectroscopy indicated that that there are significant interactions between PLLA and PGA chains in amorphous regions. Such interactions should have enhanced the growth of PLLA crystallites from the surface of PGA crystallites.
An aqueous dispersion of gold nanoparticles was added to an acrylic resin and UV‐cured. The photopolymerization process was followed by means of real‐time FT‐IR spectroscopy. Nanostructured coatings containing a homogeneous dispersion of gold nanoparticles with an average size range of 20–25 nm were achieved. Macroscopic aggregation during polymerization was avoided due to the rapid initiation and kinetic associated with the photopolymerization technique, which allowed the medium to quickly solidify around the dispersion particles.
The most widespread application of polymers in structural applications is their use as pipe material for e.g., gas distribution systems. Pipes have a design lifetime of typically 50 years, which rules out real‐time lifetime assessment methods. Here, an engineering approach is presented, which makes it possible to predict long‐term ductile failure of loaded glassy polymers based on short‐term tests. The approach is based upon the hypothesis that failure is governed by accumulation of plastic deformation up to a critical strain. A pressure‐modified Eyring relation is employed to calculate the accumulation of plastic strain for any simple loading geometry. It is demonstrated that the approach can produce accurate quantitative time‐to‐failure predictions for loaded PC specimens and uPVC pipe segments.
Novel fluoroalkyl end‐capped oligomer/hydroxyapatite nanocomposites have been easily prepared by the reaction of disodium hydrogenphosphate and calcium chloride in the presence of self‐assembled molecular aggregates formed by fluoroalkyl end‐capped oligomers in aqueous media. The fluorinated hydroxyapatite nanocomposites thus obtained were found to exhibit a good dispersibility in a variety of media, and were applied to the surface modification of glass.
The inherent properties of poly(lactide), a biocompatible and biodegradable polymer, are concurrently improved by the incorporation of a small amount of surface functionalized carbon nanotubes. A new method has been used to functionalize the CNTs' outer surface with hexadecylamine. A composite of PLA with functionalized CNTs has been prepared by melt‐extrusion. FT‐IR spectroscopy, Raman spectroscopy, DSC, and optical microscopy are used to investigate the thermal and mechanical property improvement mechanism in f‐CNTs containing PLA composite.
The influence of the flow history experienced during injection molding on the mechanical properties of amorphous polymers is investigated. It is demonstrated that flow‐induced molecular orientation only causes a small anisotropic effect on the yield stress, which can be regarded as insignificant with respect to its absolute value. Its influence on the post‐yield strain‐hardening response is also shown to be imperceptible, in contrast to a orientation which is applied during deformation below the glas transition.
Continuous and uniform yarns of thermoplastic nanofibers were prepared via direct melt extrusion of immiscible blends of thermoplastic polymers with CAB and subsequent extraction removal of CAB. Ratios of thermoplastic/sacrificial polymers, melt viscosity, and interfacial tensions affect the formation of nanofibers. Dominating sacrificing polymer content in the blends and low interfacial tensions between thermoplastic polymer and CAB are two key factors. This fabrication process possesses features of high productivity, versatility of thermoplastics, controllability, and environment friendliness in manufacturing thermoplastic nanofibers.
Glass fiber biobased composites have been prepared by ROMP of a commercially available vegetable oil derivative possessing an unsaturated bicyclic moiety, and DCPD. The resins and the corresponding composites have been characterized thermophysically and mechanically. Higher DCPD content yields materials with higher glass transition temperatures. Glass fibers significantly improve the tensile modulus of the resin from 28.7 to 168 MPa. These biobased composites utilize only a limited amount of a petroleum‐based monomer, while employing substantial amounts of a renewable resource.
A new completely biodegradable shape‐memory elastomer consisting of PLLCA reinforced by in situ PGA fibrillation is described. The manufacturing processes and shape‐memory effects of the composites are discussed. DMA results reveal a strong interface interaction between in situ PGA fibrillation and PLLCA. Compared with the SMP‐based composites that are commonly used, the shape‐memory test shows that in situ PGA fibrillation can improve the recovery properties of PLLCA; in fact, the shape‐recovery rate increases from 80.5 to 93.2%.
The aims of the current study were to synthesize new responsive polymeric microgels with embedded silver nanoparticles and then to employ these particles as catalyst for reduction reactions. To these ends, stimuli‐responsive microgels from PNIPAAm and the chitosan derivative were firstly synthesized by free radical precipitation polymerization. Then, silver nanoparticles were synthesized inside these microgel networks by in situ reduction of AgNO3. These microgels were temperature/pH sensitive with a phase transition temperature of 32–35 °C in water at pH = 3 and 8, respectively. The catalytic activity of the Ag nanoparticles for the reduction of 4‐nitrophenol can be tuned through the swelling or collapse of the responsive microgel network hosting the active nanoparticles.
A new, nickel‐coated graphite resistance‐change‐based method for gel‐point determination for epoxy‐based thermoset resins is presented and compared with DSC and rheological methods. Gelation times determined by this new method are in very good agreement with conventional techniques; this new method is potentially simpler and less time consuming than existing ones.
Newly developed shape memory (SM) epoxies are unveiled with an improved deformability range, high strength with intrinsically good thermal and chemical stability, high thermal transition (i.e., SM transformation temperature), and qualitatively excellent SM characteristics, thereby providing a synthetic route for adding attractive properties to commonly used industrial and commodity resins. The impact of chemical composition on the failure strains of these SM epoxies is shown and the resulting SM behavior is discussed.
UV‐cured polysiloxane epoxy coatings containing titanium dioxide were prepared by means of a cationic photopolymerization process. A good distribution of the inorganic filler was achieved within the polymeric network with an average size dimension of around 500 nm. UV‐vis analysis performed on organic dye (methylene blue) stained coatings showed a high efficiency of the titania photocatalytic activity: a complete degradation of the dye on the coating surface is reached after 60 min of UV irradiation without affecting the matrix photo‐degradation.
The solid and thermally instable azoinitiators V‐65 and VR‐110 were embedded within a polymer particle by using the miniemulsion process and afterwards quickly decomposed by thermal treatment below the glass temperature of the polymer. The resulting nitrogen gas overpressure inside the particles leads to a disruption of the polymer particle and a possible sudden release of encapsulated substances. It is shown, by electron microscopic measurements, that the number of burst particles correlates with the applied temperatures as well as the heating time. The surface deformation could be verified by scanning electron microscope analyses.
