Circuit techniques for 1.5-3.6-V battery-operated 64-Mb DRAM

Circuit techniques for battery-operated DRAMs which cover supply voltages from 1.5 to 3.6 V (universal V_cc), as well as their applications to an experimental 64-Mb DRAM, are presented. The universal-V_cc DRAM concept features a low-voltage (1.5 V) DRAM core and an on-chip power supply unit optimized for the operation of the DRAM. A circuit technique for oxide-stress relaxation is proposed to improve high-voltage sustaining characteristics while only scaled MOSFETs are used in the entire chip. This technique increases sustaining voltage by about 1.5 V compared with conventional circuits and allows scaled MOSFETs to be used for the circuits, which can be operated from an external V_cc of up to 4 V. A two-way power supply scheme is proposed to suppress the internal voltage fluctuation within 10% when the DRAM is operated from external power supply voltages ranging from 1.5 to 3.6 V. An experimental 1.5-3.6-V 64-Mb DRAM is designed based on these techniques and fabricated by using 0.3-μm electron-beam lithography. An almost constant access time of 70 ns is obtained. This indicates that battery operation is a promising target for future DRAMs     

Dual-regulator dual-decoding-trimmer DRAM voltage limiter forburn-in test

The authors present a dynamic RAM (DRAM) voltage limiter with a burn-in test mode. It features a dual-regulator dual-trimmer scheme that provides a precise stress voltage in a burn-in test while maintaining a constant limited voltage under normal operation. A regulator is used to preserve a constant difference between the internal burn-in voltage and the supply voltage. Two sets of trimmers reduce the voltage deviations of both the burn-in and normal-operation voltages within ±0.13 V. The circuits are implemented in a 16-Mb CMOS DRAM. A burn-in voltage regulated to ±50 mV at an ambient temperature up to 120°C is obtained simply by elevating the supply voltage to 8 V as in conventional burn-in procedures     

A 60-ns 16-Mbit CMOS DRAM with a transposed data-line structure

Low-noise, high-speed circuit techniques for high-density DRAMs (dynamic random-access memories), as well as their application to a single 5-V 16-Mb CMOS DRAM with a 3.3-V internal operating voltage for a memory array, are described. It was found that data-line interference noise becomes unacceptably high (more than 25% of the signal) and causes a serious problem in 16-Mb DRAM memory arrays. A transposed data-line structure is proposed to eliminate the noise. Noise suppression below 5% is confirmed using this transposed data-line structure. A current sense amplifier is also proposed to maintain the data-transmission speed in common I/O lines, in spite of a reduced operating voltage and increased parasitic capacitance loading in the memory array. A speed improvement of 10 ns is achieved. Using these circuit techniques, a 16-Mb CMOS DRAM with a typical RAS access time of 60 ns was realized     

A 1-Mbit BiCMOS DRAM using temperature-compensation circuittechniques

A temperature-compensation circuit technique for a dynamic random-access memory (DRAM) with an on-chip voltage limiter is evaluated using a 1-Mb BiCMOS DRAM. It was found that a BiCMOS bandgap reference generator scheme yields an internal voltage immune from temperature and V_cc variation. Also, bipolar-transistor-oriented memory circuits, such as a static BiCMOS word driver, improve delay time at high temperatures. Furthermore, the BiCMOS driver proves to have better temperature characteristics than the CMOS driver. Finally, a 1-Mb BiCMOS DRAM using the proposed technique was found to have better temperature characteristics than the 1-Mb CMOS DRAM which uses similar techniques, as was expected. Thus, BiCMOS DRAMs have improved access time at high temperatures compared with CMOS DRAMs     

A 100-MHz 4-Mb cache DRAM with fast copy-back scheme

A 4-Mb cache dynamic random access memory (CDRAM), which integrates 16-kb SRAM as a cache memory and 4-Mb DRAM into a monolithic circuit, is described. This CDRAM has a 100-MHz operating cache, newly proposed fast copy-back (FCB) scheme that realizes a three times faster miss access time over with the conventional copy-back method, and maximized mapping flexibility. The process technology is a quad-polysilicon double-metal 0.7-μm CMOS process, which is the same as used in a conventional 4-Mb DRAM. The chip size of 82.9 mm² is only a 7% increase over the conventional 4-Mb DRAM. The simulated system performance indicated better performance than a conventional cache system with eight times the cache capacity     

Block-decoded sense-amplifier driver for high-speed sensing inDRAM's

Safe sensing of the weak cell signal in DRAMs with low sense signals and fast sensing with low peak currents, both important design demands in 64- and 256-Mb DRAM development, are addressed. A block-decoded sense-amplifier driver concept is proposed. Optimized trigger pulse shapes are formed with local driver circuits to achieve high sensing safety at the beginning of the sensing period as well as fast amplification in the cell block containing the addressed memory cell. The nonaddressed blocks are triggered more slowly to reduce the peak current. Thus, reliable sensing of small initial sense signals is obtained in the shortest possible time, while the total current is kept small. As an example, for a 16-Mb DRAM, the sensing time-and hence the access time-can be reduced by at least 5 ns and is about 50% of the conventional sensing time     

256-Mb DRAM circuit technologies for file applications

256-Mb DRAM circuit technologies characterized by low power and high fabrication yield for file applications are described. The newly proposed and developed circuits are a self-reverse-biasing circuit for word drivers and decoders to suppress the subthreshold current to 3% of the conventional scheme, and a subarray-replacement redundancy technique that doubles chip yield and consequently reduces manufacturing costs. An experimental 256-Mb DRAM has been designed and fabricated by combining the proposed circuit techniques and a 0.25-μm phase-shift optical lithography, and its basic operations are verified. A 0.72-μm² double-cylindrical recessed stacked-capacitor (RSTC) cell is used to ensure a storage capacitance of 25 fF/cell. A typical access time under a 2-V power supply voltage was 70 ns. With the proper device characteristics, the simulated performances of the 256-Mb DRAM operating with a 1.5-V power supply voltage are a data-retention current of 53 μA and an access time of 48 ns     

Temperature-compensation circuit techniques for high-density CMOSDRAMs

Temperature-compensation circuit techniques are presented for the CMOS DRAM internal voltage converter, the RC-delay circuit, and the back-bias generator, which do not need any additional process steps. The above-mentioned circuits have been designed and evaluated through a 16-Mb CMOS DRAM process. These circuits have shown an internal voltage converter (IVC) with an internal voltage temperature coefficient of 185 ppm/°C, and an RC-delay circuit with a delay time temperature coefficient of 0.03%/°C. As a result, a 6.5-ns faster RAS access time and improved latchup immunity have been achieved, compared with conventional circuit techniques     

A 90-MHz 16-Mb system integrated memory with direct interface toCPU

This paper describes a system integrated memory with direct interface to CPU which integrates an SRAM, a DRAM, and control circuitry, including a tag memory (TAG). This memory realizes a computer system without glue chips, and thus enables a computer system which is low cost, low power, and compact size, but still with sufficient performance. Also fast clock cycle time and access time is realized using a newly proposed clock driver and internal signal generator. This memory is fabricated with a quad-polysilicon double-metal 0.55-μm CMOS process which is the same as used in a conventional 16-Mb DRAM. The chip size of 145.3 mm² is only a 12% increase over the conventional 16-Mb DRAM. The maximum operating frequency is 90-MHz and the operating current at cache-bit is 156-mA. This memory is suitable for various types of computer systems such as personal digital assistants (PDA's), personal computer systems, and embedded controller applications     

A 1.6-GByte/s DRAM with flexible mapping redundancy technique andadditional refresh scheme

We implemented 72-Mb direct Rambus DRAM with new memory architecture suitable for multibank. There are two novel schemes: flexible mapping redundancy (FMR) technique and additional refresh scheme. This paper shows that multibank reduces redundancy area efficiency. But with the FMR technique, this 16-bank DRAM realizes the same area efficiency as a single-bank DRAM. In other words, FMR reduces chip area by 13%. This paper also describes that additional refresh scheme reduces data retention power to 1/4. Its area efficiency is about four times better than that of the conventional redundancy approach     

A tunable CMOS-DRAM voltage limiter with stabilized feedbackamplifier

The authors present two developments for a CMOS-DRAM voltage limiter: a precise internal-voltage generator, and a stabilized driver composed of a feedback amplifier with compensation. The voltage limiter's features include generating a PMOS-V_T difference, being capable of voltage tuning with fuse trimming, and compensation in the driver circuit through zero insertion. It provides a voltage impervious to supply-voltage and substrate-voltage boundings, temperature variation, and process fluctuation, while ensuring the feedback-loop stability with a phase margin of 55° for a time-dependent load of DRAM circuit. The proposed circuits are experimentally evaluated through their implementation in a 16-Mb CMOS DRAM. A temperature dependency of 1.4 mV/°C and a voltage deviation within ±10% for process fluctuation are achieved. The voltage is stabilized within ±3% for V_CC bounce and ±10% for memory operation     

A 2.5-V 2.0-Gbyte/s 288-Mb packet-based DRAM with enhanced cellefficiency and noise immunity

A 2.5-V 288-Mb packet-based DRAM with 32 banks and 18-DQ organization architecture achieving a peak bandwidth of 2.0-GB/s at V _DD=2.25 V and T=100°C has been developed using (1) an area- and performance-efficient chip architecture with a mixture of high-speed interface circuits with DRAM peripheral circuits to increase cell efficiency; (2) a multilevel controlled bitline equalizing scheme and a distributed sense amplifier driving scheme to enhance DRAM core timing margin while increasing the number of cells per wordline for cell efficiency over the previous subwordline driving scheme; (3) a flexible column redundancy scheme with multiple fuse boxes instead of excessive spare memory cell arrays for 143 internal I/O architecture; and (4) optimized I/O circuits and pin parasitic design including pad and package to maximize the operating frequency     

Approaches to extra low voltage DRAM operation by SOI-DRAM

The newly designed scheme for a low-voltage 16 MDRAM/SOI has been successfully realized and the functional DRAM operation has been obtained at very low supply voltage below 1 V. The key process and circuit technologies for low-voltage/high-speed SOI-DRAM will be described here. The extra low voltage DRAM technologies are composed of the modified MESA isolation without parasitic MOS operation, the dual gate SOI-MOSFETs with tied or floating bodies optimized for DRAM specific circuits, the conventional stacked capacitor with increased capacitance by thinner dielectric film, and the other bulk-Si compatible DRAM structure. Moreover, a body bias control technique was applied for body-tied MOSFETs to realize high performance even at low voltage. Integrating the above technologies in the newly designed 0.5-μm 16 MDRAM, high-speed DRAM operation of less than 50 ns has been obtained at low supply voltage of 1 V     

An experimental 1.5-V 64-Mb DRAM

Low-voltage circuit technologies for higher-density dynamic RAMs (DRAMs) and their application to an experimental 64-Mb DRAM with a 1.5-V internal operating voltage are presented. A complementary current sensing scheme is proposed to reduce data transmission delay. A speed improvement of 20 ns was achieved when utilizing a 1.5-V power supply. An accurate and speed-enhanced half-V_CC voltage generator with a current-mirror amplifier and tri-state buffer is proposed. With it, a response time reduction of about 1.5 decades was realized. A word-line driver with a charge-pump circuit was developed to achieve a high boost ratio. A ratio of about 1.8 was obtained from a power supply voltage as low as 1.0 V. A 1.28 μm² crown-shaped stacked-capacitor (CROWN) cell was also made to ensure a sufficient storage charge and to minimize data-line interference noise. An experimental 1.5 V 64 Mb DRAM was designed and fabricated with these technologies and 0.3 μm electron-beam lithography. A typical access time of 70 ns was obtained, and a further reduction of 50 ns is expected based on simulation results. Thus, a high-speed performance, comparable to that of 16-Mb DRAMs, can be achieved with a typical power dissipation of 44 mW, one tenth that of 16-Mb DRAMs. This indicates that a low-voltage battery operation is a promising target for future DRAMs     

A 64-Mb DRAM with meshed power line

A 64-Mb dynamic RAM (DRAM) has been developed with a meshed power line (MPL) and a quasi-distributed sense-amplifier driver (qDSAD) scheme. It realizes high speed, t_RAS=50 ns (typical) at V_cc=3.3 V, and 16-b input/output (I/O). This MPL+qDSAD scheme can reduce sensing delay caused by the metal layer resistance. Furthermore, to suppress crosstalk noise, a V_SS shield peripheral layout scheme has been introduced, which also widens power line widths. This 64-Mb DRAM was fabricated with 0.4-μm CMOS technology using KrF excimer laser lithography. A newly developed memory cell structure, the tunnel-shaped stacked-capacitor cell (TSSC), was adapted to this 64-Mb DRAM     

A 60-MHz 240-mW MPEG-4 videophone LSI with 16-Mb embedded DRAM

A 240-mW single-chip MPEG-4 videophone LSI with a 16-Mb embedded DRAM is fabricated utilizing a 0.25-μm CMOS triple-well quad-metal technology. The videophone LSI is applied to the 3GPP 3G-324M video-telephony standard for IMT-2000, and implements the MPEG-4 video SPL1 codec, the AMR speech codec, and the ITU-T H.223 Annex B multiplexing/demultiplexing at the same time. Three 16-bit multimedia-extended RISC processors, dedicated hardware accelerators, and a 16-Mb embedded DRAM are integrated on a 10.84 mm×10.84 mm die. It also integrates camera, display, audio, and network interfaces required for a mobile video-phone terminal. In addition to conventional low-power techniques, such as clock gating and parallel operation, some new low-power techniques are also employed. These include an embedded DRAM with optimized configuration, a low-power motion estimator, and the adoption of the variable-threshold voltage CMOS (VT-CMOS). The MPEG-4 videophone LSI consumes 240 mW at 60 MHz, which is only 22% of that for a conventional multichip design. Variable threshold voltage CMOS reduces standby leakage current to 26 μA, which is only 17% of that for the conventional CMOS design     

A configurable DRAM macro design for 2112 derivative organizationsto be synthesized using a memory generator

This paper describes a DRAM macro design from which 2112 configurations up to 32 Mb can be synthesized using a memory generator. The memory generator automatically creates the layout of a DRAM macro in accordance with specification inputs such as memory capacity, address count, bank count, and I/O bits count. An expandable floor layout scheme achieves the macro size comparable to that of handicraft-designed DRAM. The memory generator can customize a configurable redundancy scheme for various macro configurations. Unified testing circuits make it possible to test DRAM macros with more than 500 interface pins in a direct-memory-access mode with 33 test pads. Up to four macros on the same chip can be tested with them. Test chips with 4-Mb DRAM and with 20-Mb DRAM fabricated with 0.35-μm technology showed 150-MHz operation     

The charge-share modified (CSM) precharge-level architecture forhigh-speed and low-power ferroelectric memory

A charge-share modified (CSM) precharge-level architecture for selective subdataline activation designed to simultaneously achieve high-speed and low-power ferroelectric nonvolatile memories is described. In this architecture, to read the data of only one memory cell destructively, the precharge level of the selected subdataline is modified by charge-sharing between the subdataline and main dataline. This architecture enables high-speed read operations, because the operations of modifying the precharge level and reading the data of memory cells are achieved simultaneously. Three circuit technologies are used in the CSM architecture to increase the operating margin: self-timing precharge circuits which solve the polarization disturbance problem without adding extra signal lines or timing margins, a boosted precharge level technique which increases the signal voltage of the nonvolatile data, and shared dummy cell circuits which improve the precision of the reference voltage over that of a conventional voltage generator. These techniques and circuits are evaluated for a simulated 16-Mb ferroelectric memory. They reduce the access time by 20 ns to 51 ns compared with the conventional architecture, while reducing the memory array current to less than 1% that of the all-subdataline activation technology     

Low-power on-chip supply voltage conversion scheme forultrahigh-density DRAMs

In order to achieve 3.3-V 1-Gb DRAM and beyond, a new on-chip supply voltage conversion scheme that converts 3.3-V external supply voltage, V_ext, to lowered 1.5-V internal supply voltage, V_ent, without any power loss within the voltage converter is proposed. This scheme connects two identical DRAM circuits in series between V_ixt and V_ss. By operation of two DRAM circuits with the same clock timing, the voltage between two DRAMs, V_int, is automatically fixed to 1/2V_ext. Therefore, each upper and lower DRAM circuit can operate at lowered 1/2V_ext without use of the conventional voltage converter. This scheme was successfully verified by an experimental system using 4-Mb DRAMs. Utilizing the proposed scheme, power dissipation was reduced by as much as 50% and stable operation was achieved without access speed penalty     

Concordant memory design: an integrated statistical design approach for multi-gigabit DRAM

Concordant memory design incorporates fluctuation in device parameters statistically into signal-to-noise ratio analysis in DRAM. In this design, the effective signal voltage of all cells in a chip is calculated, and the failed bit count of the chip is estimated. The proposed design approach gives us a quantitative evaluation of the memory array and assures 1.4-V array operation of 100-nm-1-Gb DRAM. Calculated dependence of the failed bit count on the array voltage is in close agreement with measured data for the 512-Mb DRAM chip.