共查询到19条相似文献,搜索用时 171 毫秒
1.
改进型孔板波纹填料的性能研究 总被引:1,自引:0,他引:1
介绍了北京化工大学传质分离研究室开发的新型规整填料──金属(碳钢)桥孔板波纹填料。并对其流体力学性能和传质性能进行了冷模实验研究,提出了相应的关联式和图表。与孔板波纹填料相比,它是一种适应更广泛、性能优越的高效填料。 相似文献
2.
国产BG-10型压延孔板波纹填料性能研究 总被引:2,自引:1,他引:2
用冷、热模实验研究了BG-10型压延孔板波纹填料的流体力学和传质性能.得出 了计算其压降和泛点的关联式。并与孔板波纹填料(250y)进行了对比,发现该填料 的性能优于250Y孔板波纹填料。 相似文献
3.
国产BG—10型压延孔板波纹填料性能的研究 总被引:2,自引:1,他引:2
用冷,热模实验研究了BG-10型压延孔板波纹填料的流体力学的传质性能,得出了计算其压降和泛点的关联式。并与孔板波纹填料(250y)进行了对比,发现该填料的性能优于250Y孔板波纹填料。 相似文献
4.
填料塔作为一种主要的传质与分离设备,应用已有近百年的历史了,伴随着石油化工的飞速发展,许多高效新型填料也随之迅速发展起来。目前国内开发和应用的新型填料主要有金属丝网波纹填料、金属孔板波纹填料、金属压延孔板波纹填料、塑料孔板波纹填料、陶瓷板波纹填料等。金属压延孔板波纹填料是上海医药工业研究所、北京钢铁研究总院金属填料厂和浙江工学院共同 相似文献
5.
在内径Φ30 0mm的填料塔中研究了孔板波纹填料的结构参数对液相轴向混合特性、流体力学和传质性能的影响 .研究结果表明 ,轴向返混参数随开孔率、倾角的增加及盘高的减小而增加 ,填料层压降随开孔率、盘高的增加及倾角的减小而降低 ,传质单元高度随倾角的增加、盘高的减小而降低 ,开孔率对传质单元高度的影响有一个适宜值 .通过对实验数据的回归分析得出了轴向返混参数、填料层压降及传质单元高度的关联式 .该研究结果对孔板波纹填料的开发与设计具有参考价值 相似文献
6.
7.
8.
9.
10.
四种不同比表面积双曲型高效填料的流体力学与传质性能 总被引:1,自引:1,他引:0
用4种不同比表面积双曲(SQ)型金属波纹填料进行冷模实验。通过研究SQ型填料的流体力学和传质性能可知,双曲填料特殊的弧形波纹结构降低了塔压降,改善了气液分布。研究表明,SQ填料的塔压降要明显的低于BHS型填料,当L=20.38m3/(m2·h)时,SQ800压降比BHS800降低81.5%。SQ1500在常压操作下每米理论级数最高可达到30,比SQ800的传质效率高,能耗高,但是操作范围小;板波纹SQ125填料操作范围最大但是分离效率低,适合原料粗分离;板波纹SQ250填料有较好的分离效率和较宽的操作范围,适合旧塔改造等。 相似文献
11.
12.
The effects of gas‐agitation and packing on hydrodynamics and mass transfer were investigated through experiments with air‐kerosene (benzoic acid)‐water system and corrugated‐packing of calendering plate with hole. The holdup of gas, holdup of dispersed liquid phase and mass transfer coefficient increase and the flooding velocity decrease with the increase in superficial gas velocity. Over‐agitation of gas causes over‐dispersion and emulsification of dispersed liquid phase, reduction of mass transfer performance and even flooding. The mass transfer performance of a packed column is far better than that of an unpacked column. 相似文献
13.
本文概述了SW型网孔波纹填料特点,进行了流体力学与传质性能试验,得出了传质准数关联式。与其它波纹填料的对比表明,SW型网孔波纹填料的技术和经济综合性能优良,具有广泛应用的前景。 相似文献
14.
孔结构被广泛应用于传质塔填料中,对填料上的液膜流动和传质行为影响较大。对竖直光板和多孔板上的液膜流动进行了三维模拟,并通过实验验证了模拟的准确性。通过模拟研究了孔结构对液膜流动特性的影响。结果表明,干燥孔会阻碍液膜的铺展,而润湿孔促进液膜的铺展。与光板相比,多孔板上的液膜具有起伏波,这将影响液膜的厚度分布和速度分布。液膜厚度波动和水平方向的速度波动随着孔径的增加而增加,而竖直流动方向的速度随着孔径的增加而降低。当孔径增加到一定值时,毛细波将出现在孔中的液膜中,这大大增加液膜水平方向上的波动速度,而降低流动方向上的速度。当孔径继续增加到临界值时,液膜将破裂。多孔板上孔内和气侧区域存在涡旋,能够促进内部液体交换和增大气侧扰动,从而增强传质能力。 相似文献
15.
堆叠筛板填料已在核电站放射性气体除气塔中得到成功应用。针对这一新型填料的应用设计,在较广泛的气液流量下,对气液并流下行通过不同规格堆叠筛板填料的阻力特性进行了系统的实验。实验填料共6种规格,孔径参数包括6、10和14 mm,不同孔径填料对应不同的孔间距、板间距,每种孔径填料具有正方形和正三角形两种筛孔分布方式。通过压降数据分析,研究了流动参数和几何参数(孔径、开孔率、布孔方式、板间距)对气液两相并流通过填料的流动行为及压降特性的影响;结合多孔板阻力系数经验公式提出了堆叠筛板填料干板阻力系数的计算模型,模型很好地反映了不同几何参数对干板阻力系数的影响,预测偏差在5%范围以内;基于均相流模型提出了堆叠筛板填料气液两相压降的预测模型,模型预测偏差在10%范围以内。研究工作对堆叠筛板填料塔的应用设计及进一步的传质动力学研究有一定参考价值。 相似文献
16.
17.
18.
Various tests and analysis on hydrodynamics and mass transfer properties show that, the newly invented spherical metal mesh packing (SMMP) has excellent properties from three aspects: (i) high void space (∼99%) and lower material cost; (ii) high mass transfer efficiency; (iii) easy installation, good liquid distribution, and prevention of wall flow. Moreover, SMMP is a type of isotropic spherical unit with numerous hollow holes, which realizes the regularization of random packing. The results indicate the potential of developing high-efficiency and energy-saving SMMP-based equipment. 相似文献
19.
Pascal AlixLudovic Raynal François AbbeMichel Meyer Michel PrevostDavid Rouzineau 《Chemical Engineering Research and Design》2011,89(9):1658-1668
A novel structured packing, the 4D packing, has been characterized in terms of hydrodynamics, effective area and gas side mass transfer coefficient. The increase of the 4D opening fraction allows to reduce pressure drop and to get a better capacity than Mellapak 500Y and 750Y, for which the geometric areas are similar. The 50% open 4D packing, 4D-50%, leads to effective areas which are higher than Mellapak 500Y ones, and doubled compared with MellapakPlus 252Y ones. Effective areas for the 4D do not decrease when the opening fraction increases from 30 to 50%, this indicates that a non-negligible amount of droplets is generated at 50%. Gas side mass transfer coefficient had been measured with an original experimental method: water evaporation. Corresponding results seem to be in agreement with the literature, and with the fact that a large amount of droplets is generated. Correlations are proposed for both effective area and gas side mass transfer coefficient for the 4D-50%.The 4D-50% packing could be very interesting for post-combustion CO2 capture since it generates low pressure drop and a very high interfacial area. This will be further confirmed by an economic study for which the absorber plant will be designed with a rate based model. 相似文献