Piezoelectric properties of Pb(Mn1/3Nb2/3)O3–PbZrO3–PbTiO3 ceramics with sintering aid of 2CaO–Fe2O3 compound

Since the electromechanical devices move towards enhanced power density, high mechanical quality factor (Q_m) and electromechanical coupling factor (k_p) are commonly needed for the high powered piezoelectric transformer with Q_m≥2000 and k_p=0.60. Although Pb(Mn_1/3Nb_2/3)O₃–PbZrO₃–PbTiO₃ (PMnN–PZ–PT) ceramic system has potential for piezoelectric transformer application, further improvements of Q_m and k_p are needed. Addition of 2CaO–Fe₂O₃ has been proved to have many beneficial effects on Pb(Zr,Ti)O₃ ceramics. Therefore, 2CaO–Fe₂O₃ is used as additive in order to improve the piezoelectric properties in this study. The piezoelectric properties, density and microstructures of 0.07Pb(Mn_1/3Nb_2/3)O₃–0.468PbZrO₃–0.462PbTiO₃ (PMnN–PZ–PT) piezoelectric ceramics with 2CaO–Fe₂O₃ additive sintered at 1100 and 1250 °C have been studied. When sintering temperature is 1250 °C, Q_m has the maximum 2150 with 0.3 wt.% 2CaO–Fe₂O₃ addition. The k_p more than 0.6 is observed for samples sintered at 1100 °C. The addition of 2CaO–Fe₂O₃ can significantly enhance the densification of PMnN–PZ–PT ceramics when the sintering temperature is 1250 °C. The grain growth occurred with the amount of 2CaO–Fe₂O₃ at both sintering temperatures.     

Temperature dependence of electrical and electromechanical properties of Pb(Mg1/3Nb2/3)O3–Pb(Ni1/3Nb2/3)O3–Pb(Zr,Ti)O3 thin films

The electrical and electromechanical properties of Pb(Mg_1/3Nb_2/3)O₃–Pb(Ni_1/3Nb_2/3)O₃–Pb(Zr,Ti)O₃ (PMN–PNN–PZT, PMN/PNN/PZT = 20/10/70) on Pt/Ti/SiO₂/Si substrates by chemical solution deposition was investigated. The PMN–PNN–PZT films annealed at 650 °C exhibited slim polarization hysteresis curves and a high dielectric constant of 2100 at room temperature. A broad dielectric maximum at approximately 140–170 °C was observed. The field-induced displacement was measured by scanning probe microscopy, the bipolar displacement was not hysteretic, and the effective piezoelectric coefficient (d₃₃) was 66 × 10⁻¹² m/V. The effective d₃₃ decreased with temperature, but the value at 100 °C remained 45 × 10⁻¹² m/V.     

Dielectric and ferroelectric properties of lead indium niobate ceramic prepared by wolframite method

The dielectric and ferroelectric properties of lead indium niobate (Pb(In_1/2Nb_1/2)O₃, PIN) ceramic prepared by an oxide-mixing method via wolframite route were investigated. The 98.5% perovskite fine-grained PIN ceramics with average grain sizes of 1–2 μm were obtained by sintering at 1050 °C for 2 h. The dielectric properties of the PIN were of relaxor ferroelectric behavior with temperature of dielectric maximum (T_m) 53 °C and dielectric constant (_r) 4300 (at 1 kHz). The P–E hysteresis loop measurements at various temperatures showed that the ferroelectric properties of the PIN ceramic changed gradually from the paraelectric behavior at temperature above T_m to slim-loop type relaxor behavior at temperature below T_m. Moreover, the P–E loop became more open at temperatures much lower than T_m. At −25 °C, the maximum polarization is found to be 8 μm/cm² at a field of 30 kV/cm, with P_r value of 2.5 μm/cm² and E_c of +7.5 kV/cm.     

Luminescent properties of Pr doped ZrSiO4 phosphors

Mixtures of ZrO₂, SiO₂, Pr₂O₃, and H₃BO₃ were fired at the temperature of 1150–1350 °C under H₂ atmosphere. A single phase ZrSiO₄:Pr phosphors could be achieved at the firing temperature above 1150 °C. Crystallinity and PL properties strongly depended on the flux amounts, firing temperature, and dopant concentrations. ZrSiO₄:Pr phosphors showed a strong red emission at 615 nm and a weak red emission at 622 nm with an excitation wavelength of 295 and 450 nm, respectively. Two sets of the emission bands and excitation spectra originated from Pr³⁺ ions at Zr and Si sites, respectively.     

Luminescent properties of Eu-doped YTaO4 powders

YTaO₄:Eu³⁺ powders were synthesized by a flux method with LiCl. The use of a flux in the synthesis of M′–YTaO₄ facilitated the reaction of raw materials, leading to lowering the heating temperature, but not effective at the high firing temperature. The red emission peaks were observed around 613 nm with an excitation wavelength of 254 nm. Emission peaks were composed of two sets around 613 nm and 590 nm, which originated from ⁵D₀–⁷F₂ and ⁵D₀–⁷F₁, respectively. PL intensity of YTaO₄:Eu³⁺ prepared with a small amount of LiCl (10 wt%) significantly depended on the firing temperatures, while that with a larger amount of LiCl (40 wt%) slightly relied on firing temperatures. The highest PL intensity could be obtained at the firing conditions of 1300 °C and 10 wt% LiCl.     

Absence of E. coli regrowth after Fe and TiO2 solar photoassisted disinfection of water in CPC solar photoreactor

Field disinfection of water in a large solar compound parabolic collector (CPC) photoreactor (35–70 l) was conducted at 35 °C by different photocatalytic processes: sunlight/TiO₂, sunlight/TiO₂/Fe³⁺, sunlight/Fe³⁺/H₂O₂ and compared to the control experiment of direct sunlight alone. Experiments were carried out using a CPC and natural water spiked with E. coli K 12. Under these conditions, total disinfection by bare sunlight irradiation was not reached after 5 h of treatment; and bacterial recovery was observed during the subsequent 24 h in the dark.

The addition of TiO₂, TiO₂/Fe³⁺ or Fe³⁺/H₂O₂ to the water accelerates the bactericidal action of sunlight, leading to total disinfection by solar-photocatalysis. No bacterial regrowth was observed during 24 h after stopping sunlight exposure. For some samples, the decrease of bacteria continues in the dark. A “residual disinfection effect” was observed for these samples before reaching the total inactivation. The effective disinfection time (EDT₂₄), defined as the treatment time required to prevent any bacterial regrowth during the subsequent 24 h in the dark, after stopping the phototreatment, was reached in the presence but not in the absence of different photocatalytic systems. EDT₂₄ was 2 h 30 min, 2 h and 1 h 30 min for sunlight/TiO₂, sunlight/TiO₂/Fe³⁺ and sunlight/Fe³⁺/H₂O₂ systems, respectively. The post irradiation events observed when the phototreated water is poured into an optimal growth medium are also discussed.     

Electrical properties of (Bi2O3)0.75(RE2O3)0.25 ceramics (RE=Dy, Y, Ho, Er and Yb)

Five kinds of rare earth stabilized bismuth oxide ceramics, (Bi₂O₃)_0.75(RE₂O₃)_0.25 (RE=Dy, Y, Ho, Er and Yb), were synthesized by sintering a mixture of Bi₂O₃ and RE₂O₃ at 900–1100 °C and their electrical properties were investigated. The bulk density and the lattice constant linearly increased with an increase in the atomic weight of RE and the ionic radius of RE³⁺, respectively. The electrical conductivity at 300 °C slightly increased with the increasing ionic radius of RE³⁺, while at 500 and 700 °C, it was constant regardless of the ionic radius of RE³⁺. The migration activation energy and the association activation energy showed a maximum value and a minimum value at RE=Er, respectively.     

Effects of the sintering atmosphere on Nb-based dielectrics

The effects of a forming atmosphere on the stability, the sintering and the dielectric properties of Ba₅Nb₄O₁₅, BaNb₂O₆, ZnNb₂O₆ and Zn₃Nb₂O₈ ceramics were investigated, because of the primary importance of the sintering atmosphere in relation to copper sintering. These Nb-based materials were sintered in air and in Ar/H₂10%. Zn-containing samples are very sensitive to the reductive atmosphere. ZnO volatilises at 800–850 °C and the resulting compound does not exhibit the expected properties. BaNb₂O₆ and Ba₅Nb₄O₁₅ are more stable in term of relative weight loss. Nevertheless, the phase analysis reveals a modification of the BaNb₂O₆ phase, what induces the degradation of the dielectric property stability versus temperature. The properties of Ba₅Nb₄O₁₅ are not modified by a sintering in reductive atmosphere. A relative permittivity of 38.8, a permittivity temperature coefficient of −150 ppm °C⁻¹ and an insulating resistivity of 10^10.9 Ω cm were obtained for this latter.     

Partial oxidation of light paraffins on supported superacid catalytic membranes

Superacid-supported catalytic membranes were found to be active and very selective in the partial oxidation of light paraffins (C₁–C₂) with H₂O₂ under mild conditions (T_R: 80–110°C; P_R: 1.4 bar) in a three-phase catalytic membrane reactor (3PCMR). Among different catalytic membranes investigated, Nafion-based ones showed the best performance in terms of both activity and selectivity. Addition of Fe²⁺ ions in the liquid phase enhances the reaction rate, however, a volcano-shaped trend between reaction rate and concentration of Fe²⁺ was observed. Reaction temperature drastically affects both reaction rate and product distribution. A reaction pathway based on the electrophilic hydroxylation of the C–H bond on superacid sites and subsequent reaction of the activated paraffin with OH radicals has been proposed.     

Partial oxidation of propane on Nafion supported catalytic membranes

Nafion supported catalytic membranes were found to be effective in the partial oxidation of propane to oxygenates with H₂O₂ in the presence of Fe²⁺ under mild conditions. The influence of [Fe²⁺] and [H₂O₂] on the reaction rate and product distribution in the temperature range 80–110°C has been ascertained. A reaction pathway involving the electrophilic activation of propane on superacid sites and subsequent reaction of the activated propane molecules with OH radicals generated by Fe²⁺/H₂O₂ Fenton system is discussed.     

Synthesis, sintering and characterization of PNZST ceramics from high-energy ball milling process

Pb_0.99Nb_0.02[(Zr_0.60Sn_0.40)_0.94Ti_0.06]_0.98O₃ powders were synthesized from oxide mixtures of Pb₃O₄, Nb₂O_5, ZrO₂, SnO_2, and TiO₂ using a Fritsch P4™ vario-planetary ball milling system. The perovskite structure of PNZST powder can be obtained well after 14 h milling and crystallite size of the powders greatly reduced to 20–30 nm. The resultant powders have better sinterability characteristics to obtain dense ceramic bodies at low temperature. The dielectric constant of samples shows a maximum at 1150 °C and the PE_MC to PE_SC transformation temperature shifts to higher temperature with an increase in grain size. The field-induced strain reaches maximum longitudinal strain of 0.32% and the P–E hysteresis loop shows much higher squareness at 1150 and 1200 °C. The measured dielectric and antiferroelectric properties of the PNZST ceramics were found to be comparable to those from other processing techniques.     

Dielectric and ferroelectric properties of Ba(ZrxTi1−x)O3 ceramics

It is known that Curie temperature of barium titanate system can be altered by the substitution of dopants into either A- or B-site. Dopants could pinch transition temperature, lower Curie temperature, and raise the rhombohedral–orthorhombic and orthorhombic–tetragonal phase transition close to room temperature. This isovalent substitution could improve the ferroelectric properties of the BaTiO₃-based system. In this study, barium zirconate titanate Ba(Zr_xTi_1−x)O₃ (BZT; x = 0, 0.02, 0.05 and 0.08) ceramics were prepared by conventionally mixed-oxide method. The ferroelectric properties of BZT ceramics were investigated. Increasing Zr content in the BaTiO₃-based compositions caused a decrease in Curie temperature (T_c). At T_c, the highest relative permittivity of BZT with an addition of 0.08 mol% of Zr was 12,780. The BZT specimens with the additions of 0.05 mol% and 0.08 mol% of Zr presented the remanent polarization at 25 μC/cm² and 30 μC/cm², respectively.     

Removal of Fe(III) ion from aqueous solution by adsorption on raw and treated clinoptilolite samples

Iron (III) adsorption from aqueous solutions onto raw and pretreated clinoptilolite was investigated here. Various parameters for iron removal; initial solution pH, contact time and metal ion concentration were optimized. The equilibrium data were modeled by both the Langmuir and Freundlich adsorption isotherms at optimal conditions. Adsorption capacities of raw samples and those pretreated with Na₂S₂O₈ at 20 °C , 70 °C and with HNO₃ at 20 °C were all similar but samples pretreated with HNO₃ at 70 °C were significantly different; iron (III) removal from samples pretreated with HNO₃ decreased with increasing pretreatment temperature. Tests with Fe⁺³ solutions containing phenol, CsCl or KCl, indicated the continued presence of these ions in zeolite which either promoted or retarded the adsorption of iron. The Fe⁺³ adsorption capacity of clinoptilolite pretreated with HNO₃ at 70 °C was about two times greater with, than without, CsCl and KCl. The kinetics of iron adsorption from aqueous solution were also investigated using the first-order Lagergren equation and a pseudo-second-order model.     

Electrical and mechanical properties of ferroelectric lead zirconate titanate/tungsten oxide ceramics

Ferroelectric PZT/xWO₃ ceramics (when x = 0, 0.5, 1, 3 and 5 vol%) were fabricated from PZT and nano-sized WO₃ powders by a solid-state mixed-oxide method. Phase characterization suggested that the reaction between PZT and WO₃ occurred during the sintering. This reaction seemed more pronounced with increasing the content of WO₃. The maximum density at approximately 97% of the theoretical value was achieved at 1 vol% of WO₃ addition. The grain size was reduced with an addition of WO₃ particles from 7.8 μm for PZT to 1.8 μm for 0.5 vol% WO₃ and 0.8 μm for 1–5 vol% WO₃. Mechanical properties of PZT could be improved with an addition of WO₃ nano-particulates. The addition of 0.5 vol% WO₃ could maintain good electrical properties while increasing WO₃ significantly reduced dielectric and piezoelectric constants of the PZT.     

Characterization and catalytic investigation of Fe-ZSM5 for urea-SCR

Fe-ZSM5 was prepared with high iron content by solid-state ion exchange and characterized by ICP-AES, BET surface measurements, TEM, UV–vis, EPR and DRIFT spectroscopy as well as supplementing catalytic tests in order to clear up its functionality in urea-SCR. Due to the over-exchange with iron small Fe₂O₃ particles were formed, identified by UV–vis, EPR and TEM measurements, which were proved to be not active for the SCR reaction. However, the oxidation of NO to NO₂ over Fe³⁺ ions in the catalyst was realized to be a pre-requisite for the SCR reaction and the rate-determining step. DRIFT investigations under SCR conditions showed adsorbates on Fe²⁺ up to 300 °C. The high SCR activity above 300 °C can be explained by the faster reoxidation of Fe²⁺ to Fe³⁺ sites at high temperatures. The observed inhibition of the SCR reaction by excess ammonia at low and intermediate temperatures can be explained in this context by the reducing properties of ammonia converting Fe³⁺ to Fe²⁺ or by preventing the reoxidation of Fe²⁺.     

Effective Au-Au-Clx/Fe(OH)y catalysts containing Cl for selective CO oxidations at lower temperatures

Supported Au catalysts Au-Au⁺-Cl_x/Fe(OH)_y (x < 4, y ≤ 3) and Au-Cl_x/Fe₂O₃ prepared with co-precipitation without any washing to remove Cl⁻ and without calcining or calcined at 400 °C were studied. It was found that the presence of Cl⁻ had little impact on the activity over the unwashed and uncalcined catalysts; however, the activity for CO oxidation would be greatly reduced only after Au-Au⁺-Cl_x/Fe(OH)_y was further calcined at elevated temperatures, such as 400 °C. XPS investigation showed that Au in catalyst without calcining was composed of Au and Au⁺, while after calcined at 400 °C it reduced to Au⁰ completely. It also showed that catalysts precipitated at 70 °C could form more Au⁺ species than that precipitated at room temperatures. Results of XRD and TEM characterizations indicated that without calcining not only the Au nano-particles but also the supports were highly dispersed, while calcined at 400 °C, the Au nano-particles aggregated and the supports changed to lump sinter. Results of UV–vis observation showed that the Fe(NO₃)₃ and HAuCl₄ hydrolyzed partially to form Fe(OH)₃ and [AuCl_x(OH)_4−x]⁻ (x = 1–3), respectively, at 70 °C, and such pre-partially hydrolyzed iron and gold species and the possible interaction between them during the hydrolysis may be favorable for the formation of more active precursor and to avoid the formation of Au–Cl bonds. Results of computer simulation showed that the reaction molecular of CO or O₂ were more easily adsorbed on Au⁺ and Au⁰, but was very difficultly absorbed on Au⁻. It also indicated that when Cl⁻ was adsorbed on Au⁰, the Au atom would mostly take a negative electric charge, which would restrain the adsorption of the reaction molecular severely and restrain the subsequent reactions while when Cl⁻ was adsorbed on Au⁺ there only a little of the Au atom take negative electric charge, which resulting a little impact on the activity.     

Kinetics and mass transfer effects in the oxidation of ferrous sulfate over doped active carbon catalysts

Ferric sulfate is used in water purification. The oxidation of ferrous sulfate, FeSO₄, to ferric sulfate in acidic aqueous solutions of H₂SO₄ over finely dispersed active carbon particles was studied in a vigorously stirred batch reactor. Molecular oxygen was used as the oxidation agent and two kinds of catalysts were utilized: active carbon, doped active carbon. Both active carbon and doped active carbon catalysts enhanced the oxidation rate considerably.

Systematic kinetic experiments were carried out at the temperature and pressure ranges of 60–100°C and 4–10 bar, respectively. The results revealed that both non-catalytic and catalytic oxidation of Fe²⁺ take place simultaneously. The experimental data were fitted to rate equations, which were based on a plausible reaction mechanism: adsorption of dissolved oxygen on active carbon, electron transfer from Fe²⁺ ions to adsorbed oxygen and formation of surface hydroxyls. A comparison of the Fe²⁺ concentrations predicted by the kinetic model with the experimentally observed concentrations indicated that the mechanistic rate equations were able to describe the intrinsic oxidation kinetics of Fe²⁺ over pure active carbon and doped active carbon catalysts.     

Effect of glass additions on the sintering and microwave properties of composite dielectric ceramics based on BaO–Ln2O3–TiO2 (Ln = Nd, La)

Ten weight percent BBZS (Bi₂O₃, B₂O₃, ZnO and SiO₂) glass was added to x(Ba₄Nd_9.333Ti₁₈O₅₄) − (1 − x)(BaLa₄Ti₄O₁₅) (BNLT, 0 ≤ x ≤ 1) composite dielectric ceramics to lower their sintering temperature whilst retaining microwave properties useful for low temperature co-fired ceramic and antenna core technology. With the addition of 10 wt% BBZS glass, dense BNLT composite ceramics were produced at temperatures between 950 and 1140 °C, depending on composition (x), an average reduction of sintering temperature by 350 °C. X-ray diffraction, scanning and transmission electron microscopy and Raman spectroscopy studies revealed that there was limited inter-reaction between BLT/BNT and the BBZS glass. Microwave property measurement showed that the addition of BBZS glass to BNLT ceramics had a negligible effect on _r and τ_f, although deterioration in the measured quality factor (Qf) was observed. The optimised composition (xBNT − (1 − x)BLT)/0.1BBZS (x = 0.75) had _r  61, τ_f  38 ppm/°C and Qf  2305 GHz.     

Synthesis and properties of Bi0.5(Na1−x−yKxAgy)0.5TiO3 lead-free piezoelectric ceramics

Bi_0.5(Na_1−x−yK_xAg_y)_0.5TiO₃ piezoelectric ceramics were prepared by conventional ceramic processes. X-ray diffraction patterns show a pure perovskite structure, indicating that the K⁺ and Ag⁺ ions substitute for the Na⁺ ions in Bi_0.5Na_0.5TiO₃. The temperature dependence of the dielectric constant and dissipation factor shows all ceramics to experience two phase transitions: from ferroelectric to anti-ferroelectric and from anti-ferroelectric to paraelectric. The transition temperature from ferroelectric to anti-ferroelectric and the temperature at which the dielectric constant reaches its maximum value decrease with the increase of K⁺ amount. At room temperature, the ceramics containing 17.5–20 mol% K⁺ and 2 mol% Ag⁺ exhibit high piezoelectric constant (d₃₃ = 180 pC/N) and high electromechanical coupling factor (k_p = 35%).     

Micromechanics of domain switching in rhombohedral PZT ceramics

The lattice strain {2 0 0} and diffraction peak intensity ratio R{1 1 1} have been determined in soft rhombohedral PZT ceramics during the application of an electric field up to 2.5 MV m⁻¹ and as a function of the grain orientation ψ, using high energy synchtron X-ray diffraction. The magnitude of both {2 0 0} and R{1 1 1} increased sharply beyond a field level of 1 MV m⁻¹ due to the onset of ferroelectric domain switching. {2 0 0} exhibited a near linear dependence on cos² ψ, in agreement with previous studies of the remanent-poled state. In contrast, the R{1 1 1}–cos² ψ plot showed evidence of saturation in ferroelectric domain switching, particularly for ψ > 60°. The development of lattice strain during poling is discussed in terms of contributions from the intrinsic piezoelectric effect and from residual stress caused by differences in the poling strain of a grain, and the piezoelectric strain of a grain relative to its surroundings.