基于细观有限元方法的复合材料横向力学性能分析

横向断裂是制约复合材料结构设计的关键点,传统细观模型因为不能充分考虑组分性能、体积分数和纤维形状及分布情况而不能有效预测材料横向力学性能。采用改进的随机序列吸收算法建立具有随机纤维分布的复合材料代表性体积单胞模型,考虑基体破坏和界面脱粘两种失效模式和固化过程中产生的残余应力,对模型在横向拉、压、剪3种载荷下的力学行为进行仿真计算。分析了不同界面强度对复合材料力学性能的影响规律。仿真结果与实验数据对比表明:横向模量预测误差在7%以内,压缩和剪切的强度误差在8%以内,结果一致性较好,表明该模型能够有效预测复合材料横向力学性能。     

正交铺设陶瓷基复合材料单轴拉伸行为

采用细观力学方法对正交铺设陶瓷基复合材料单轴拉伸应力-应变行为进行了研究。采用剪滞模型分析了复合材料出现损伤时的细观应力场。采用断裂力学方法、 临界基体应变能准则、 应变能释放率准则及Curtin统计模型4种单一失效模型确定了90°铺层横向裂纹间距、 0°铺层基体裂纹间距、 纤维/基体界面脱粘长度和纤维失效体积分数。将剪滞模型与4种单一损伤模型结合, 对各损伤阶段应力-应变曲线进行了模拟, 建立了复合材料强韧性预测模型。与室温下正交铺设陶瓷基复合材料单轴拉伸应力-应变曲线进行了对比, 各个损伤阶段的应力-应变、 失效强度及应变与试验数据吻合较好。分析了90°铺层横向断裂能、 0°铺层纤维/基体界面剪应力、 界面脱粘能、 纤维Weibull模量对复合材料损伤及拉伸应力-应变曲线的影响。      

SiC/Ti-6Al-4V复合材料在横向拉伸载荷下界面失效行为的数值模拟

采用有限元模拟了SiC/Ti-6Al-4V复合材料冷却过程和横向拉伸试验过程, 横向拉伸试样采用十字形试样。分别建立了平面应力和轴对称有限元模型, 采用平面应力有限元模型计算环绕纤维圆周的界面微区应力分布, 预测界面失效机制。采用轴对称有限元模型分析复合材料界面脱粘过程以及残余应力对界面径向应力分布的影响。结果表明: 对于SiC/Ti-6Al-4V复合材料十字形试样,在横向拉伸载荷下的界面失效由径向应力导致,界面失效模式为法向失效, 剪切失效模式未发生; 十字形试样在横向拉伸载荷下界面初始脱粘位置处于界面中间; 随横向拉伸应力增加, 十字形试样的界面脱粘对称向两边扩展; 界面径向应力随残余应力降低而升高。     

热残余应力对考虑微观孔隙碳纤维增强环氧树脂复合材料横向拉伸性能的影响

为研究由于材料固化产生的热残余应力对碳纤维增强环氧树脂复合材料横向拉伸性能预测结果的影响,发展了一种基于摄动算法的纤维和孔洞随机分布代表性体积单元（RVE）生成方法,建立更加接近真实材料微观结构的RVE模型。通过施加周期性边界条件,并赋予组分（纤维、基体和界面）材料本构关系,进而实现温度和机械荷载下模型的热残余应力和损伤失效分析。从结果中发现,材料固化过程会在纤维之间产生残余压应力,在模型孔隙周围产生沿加载方向的残余拉应力。所建立不含孔隙RVE模型的失效均是由于界面脱黏引起,材料固化在纤维之间产生的残余压应力会增加模型的预测强度。含有孔隙的RVE模型失效起始于孔隙周围的基体中,而材料固化在模型孔隙周围产生的热残余拉应力对含孔隙RVE模型预测的失效强度有降低作用。对于具有不同孔隙尺寸的RVE模型,模型的失效强度随着孔隙尺寸的增加而不断降低,但是热残余应力减弱了孔隙尺寸对模型预测结果的降低作用。对于具有不同长宽比椭圆形孔隙的RVE模型,热残余应力增加了孔隙长宽比对模型强度的降低作用。      

2D-C/ SiC 复合材料的宏观拉压特性和失效模式

通过拉伸、压缩实验, 从宏观上研究了平纹编织C/ SiC 复合材料在简单载荷作用下模量、残余应变及泊松比的变化。通过断口观察, 分析了材料在面内拉、压载荷作用下的损伤与失效模式。实验结果表明, 拉伸载荷作用下, 材料在低应力就开始损伤。0°纤维束表面基体开裂和层间裂纹是主要损伤形式。损伤后, 随着应力增加, 拉伸卸载模量、泊松比线性减小, 残余应变增加; 压缩应力-应变基本呈直线关系, 模量、泊松比基本不变。拉伸破坏表现为韧性断裂, 断裂机理为分层后0°纤维束的断裂、携带90°纤维束拔出; 压缩破坏形成一个与加载方向成13°的断裂平面, 破坏机理为层间裂纹、0°/ 90°纤维束之间裂纹和90°纤维束内裂纹的产生和迅速扩展、最后0°纤维束剪切断裂。      

双向等轴拉伸载荷下二维编织陶瓷基复合材料的应力-应变行为预测

将二维编织结构简化为(0°/90°)s正交铺层结构。采用含损伤变量的剪滞分析理论,解得双向等轴拉伸载荷下,0°层和90°层开裂后各层的应力分布;基于随机基体裂纹演化理论,随机纤维损伤和最终失效理论,确定了0°层和90°层沿纤维方向的应力-应变关系,以及切线拉伸模量与施加载荷之间的关系;然后,将切线拉伸模量代入正交铺层结构的剪滞分析中,进而预测出二维编织陶瓷基复合材料在双向等轴拉伸载荷下的应力-应变关系。预测结果表明:在双向等轴拉伸载荷下,二维编织陶瓷基复合材料的横向和纵向应力-应变曲线基本相同,与单向加载时的应力-应变曲线相近。     

短纤维增强金属基复合材料的热残留应力及在拉伸和压缩载荷作用下的应力分布

发展了文献[1]中提出的变形模型, 研究了短纤维增强金属基复合材料热残留应力的分布及其对拉伸和压缩载荷下应力分布的影响。研究表明, 在拉伸和压缩载荷下, 热残留应力可导致不对称的应力分布和基体塑性, 热残留应力降低拉伸时的应力传递, 加强压缩时的应力传递。      

残余应力对复合材料横向拉伸和压缩性能的影响EI

采用显微激光分析仪对由力学性能不同的两种基体所制备的玻璃纤维复合材料进行了残余应力测定,并考察了残余应力对复合材料横向拉伸和压缩强度的影响。结果表明:1.用显微激光分析仪可方便地测定玻璃纤维复合材料的相对残余应力;2.基体韧性增加可部分松弛复合材料的残余应力;3.残余应力的存在使复合材料的横向拉伸强度降低,但对提高横向压缩强度有利。     

单向纤维增强陶瓷基复合材料单轴拉伸行为

采用细观力学方法对单向纤维增强陶瓷基复合材料的单轴拉伸应力-应变行为进行了研究。采用Budiansky-Hutchinson-Evans（BHE）剪滞模型分析了复合材料出现损伤时的细观应力场,结合临界基体应变能准则、应变能释放率准则以及Curtin统计模型三种单一失效模型分别描述陶瓷基复合材料基体开裂、界面脱粘以及纤维失效三种损伤机制,确定了基体裂纹间隔、界面脱粘长度和纤维失效体积分数。将剪滞模型与3种单一失效模型相结合,对各个损伤阶段的应力-应变曲线进行模拟,建立了准确的复合材料强韧性预测模型,并讨论了界面参数和纤维韦布尔模量对复合材料损伤以及应力-应变曲线的影响。与室温下陶瓷基复合材料单轴拉伸试验数据进行了对比,各个损伤阶段的应力-应变、失效强度及应变与试验数据吻合较好。     

树脂基纤维复合材料的热残余应力数值分析

以环氧树脂R368-1/硼纤维复合材料为研究对象,采用柱体单胞结构,建立了三维有限元分析模型。考虑试样加工制备过程和常温使用时的温度差,对残余应力分布特点和应力水平进行了讨论,给出了应力分布云图和应力沿径向的分布规律。进一步考察了纤维体积分数、温度差和附加界面层对残余应力分布的影响,结果表明,基体主要受拉伸应力作用,纤维主要受压缩应力作用,纤维体积分数增加和附加界面层有助于改善复合材料中残余应力的分布,试样制备温度的升高对纤维中应力的增加具有较大影响。     

Development of damage in a 2D woven C/SiC composite under mechanical loading: I. Mechanical characterization

An investigation has been undertaken to determine the damage mechanisms and the associated mechanical response of a 2D reinforced composite of carbon fibers in an SiC CVI-processed matrix subjected to uniaxial tensile and compressive loadings at room temperature. Under tension loading, an extended non-linear stress/strain response was evidenced and related to a multi-stage development of damage involving transverse matrix microcracking, bundle/matrix and inter-bundle debonding as well as thermal residual stress release. This tensile behavior proved to be damageable-elastic with respect to a fictitious thermalstress-free origin of the stress/strain axis lying in the compression domain. In compression, after an initial stage involving closure of the thermal microcracks present from processing, the composite displayed a linear-elastic behavior until failure. The extent of damage over the material was characterized quantitatively at the microscale by the decrease of the average transverse microcrack spacing and at the macroscale by the decrease of both the longitudinal Young's modulus and the in-plane Poisson's ratio.     

Investigating the transverse behavior of Glass–Epoxy composites under intermediate strain rates

In this study, the strain rate effects on transverse tensile and compressive properties of unidirectional Glass fiber reinforced polymeric composites are investigated. To demonstrate strain rate effects, the tensile and compressive composite specimens with identical configuration are fabricated and tested to failure in the transverse direction at quasi-static strain rate of approximately 0.001 s⁻¹ and intermediate strain rates of 1–100 s⁻¹. The tensile and compressive tests are performed using a servo-hydraulic testing apparatus equipped with strain rate increasing mechanisms. For performing the practical tests, a jig and a fixture and other test supplies are designed and manufactured. The performance of the test jig is evaluated and showed that it is adequate for composites testing under tension and compression loads. The effects of strain rate on mechanical properties (maximum strength, modulus, and strain to failure) are considered. The characteristic results for the transverse properties indicate that damage evolution is strain-rate-dependent for the examined material. Also, a strain-rate-dependent empirical material model associated with different regression constants is proposed based on the experimental results obtained to characterize the rate dependent behavior of Glass/Epoxy composite material.     

陶瓷纤维增强氧化硅气凝胶复合材料力学性能试验

氧化硅气凝胶具有极低的热导率和密度,可作为很好的隔热材料,而脆弱的力学性能限制了其在隔热领域的应用。在不影响隔热效果的前提下,通过复合陶瓷纤维可增加氧化硅气凝胶的强度及韧性。试验探索了陶瓷纤维增强氧化硅气凝胶在室温下的拉伸、压缩和剪切等基本力学性能,分别研究了300℃、600℃和900℃下复合材料纤维铺层面方向的压缩性能,并采用扫描电子显微镜对高温试样微观结构进行了观察分析。结果表明：陶瓷纤维增强氧化硅气凝胶的性能表现出方向性,弹性模量在铺层面内方向与厚度方向的数值最大相差约28倍,强度极限亦然;在室温条件下,复合材料的拉伸和压缩弹性模量不同,X 、Y 和 Z 方向拉伸模量与对应的压缩模量之比分别为1.60、1.83和0.56;高温下复合材料沿厚度方向收缩,收缩量随温度升高而增大,900℃下的最大收缩量可达10.8%;高温下复合材料铺层面内方向压缩性能随温度升高而增强。     

Tensile and Compressive Properties of FRP Composites with Localised Fire Damage

The effect of localised fire damage on the tensile and compressive properties of fibre-reinforced polymer (FRP) composites is investigated. A simple model based on rule-of-mixtures is presented for determining reductions to the tensile stiffness, tensile strength, compressive stiffness and compressive strength of composite panels with localised fire damage of any shape and size. The validity of the model is rigorously tested against experimental tension and compression property data for a glass/polyester composite with localised fire damage in the shape of a circle, oval, square, diamond or in a irregular shape. The model is found to accurately predict the tension and compression properties of composites with localised fire damage of any shape, and is expected to be a useful model for estimating the residual structural integrity of fire-damaged composite panels.     

Thermal cycling response behavior of ceramic matrix composites under load and displacement constraints

Thermal cycling response of a two-dimensional carbon fiber reinforced SiC matrix composite (2D C/SiC) to load constraint (LC) and to displacement constraint (DC) in an oxidizing environment was investigated. During thermal cycling between 700 and 1200 °C, a constraint strain with a 0.208% range and a constraint stress with a 180 MPa range were, respectively, generated on the composites in LC and DC. It was found that with increasing cycles, the constraint strain increased in LC and the constraint stress decreased in DC. After 50 cycles, in contrast to the as-received composite materials, the as-cycled composites suffered greater loss in mechanical properties: the residual strength and failure strain are 204 MPa and 0.49% for the LC tested samples, and 223 MPa and 0.64% for the DC tested samples, respectively. Microstructural observations indicated that the LC could develop thermal microcracks and assist in oxidizing the internal fibers, whereas the DC reduced crack propagations and fiber oxidation because of decreasing tensile and increasing compressive stresses.     

Ultra-high-ductile behavior of a polyethylene fiber-reinforced alkali-activated slag-based composite

This paper presents an experimental study of the meso-level composite properties of an ultra-high-ductile polyethylene-fiber-reinforced alkali-activated slag-based composite. Four mixtures with 1.75 vol% of polyethylene fibers were prepared with varying water-to-binder ratio. The viscosity of the matrix was controlled to ensure a uniform fiber dispersion. A series of experiments, including density, compression, and uniaxial tension tests, was performed to characterize the mechanical properties of the composite. The test results showed that the average tensile strength to compressive strength ratio of the composites was 19.8%, nearly double that of normal concrete, and the average crack width was 101 μm. It was also demonstrated that tensile strain capacity and tensile strength of up to 7.50% and 13.06 MPa, respectively, can be attained when using the proposed polyethylene-fiber-reinforced alkali-activated slag-based composites.     

碳纤维复合材料假脚工艺参数对其冲击后疲劳性能的影响

基于三维逐渐损伤理论和有限元法,对碳纤维复合材料假脚的冲击及冲击后疲劳破坏过程进行分析,研究了不同的复合材料体系、几何尺寸、纤维铺设方式等工艺参数对碳纤维假脚的冲击损伤及疲劳性能的影响规律。结果表明,在冲击载荷作用下,碳纤维复合材料假脚的损伤模式主要为基体开裂、纤维压缩和分层;复合材料体系的横向和法向拉伸强度以及剪切强度等参数越小,假脚的冲击损伤面积越大,所能承受的疲劳循环次数越低;随着后龙骨厚度的增加,基体开裂损伤面积越来越大,分层损伤面积略有减小,而纤维压缩损伤几乎没有变化。尽管随着后龙骨厚度的增加,假脚的疲劳循环次数逐渐增大,但是相对于厚度的增加量,疲劳循环次数的增加量相对较小;不同铺层参数对碳纤维复合材料假脚的冲击损伤模式几乎没有影响。适度增加0°铺层的含量,可有效提高碳纤维复合材料假脚的疲劳性能。     

Meso-Scale Progressive Damage Behavior Characterization of Triaxial Braided Composites under Quasi-Static Tensile Load

Based on continuum damage mechanics (CDM), a sophisticated 3D meso-scale finite element (FE) model is proposed to characterize the progressive damage behavior of 2D Triaxial Braided Composites (2DTBC) with 60° braiding angle under quasi-static tensile load. The modified Von Mises strength criterion and 3D Hashin failure criterion are used to predict the damage initiation of the pure matrix and fiber tows. A combining interface damage and friction constitutive model is applied to predict the interface damage behavior. Murakami-Ohno stiffness degradation scheme is employed to predict the damage evolution process of each constituent. Coupling with the ordinary and translational symmetry boundary conditions, the tensile elastic response including tensile strength and failure strain of 2DTBC are in good agreement with the available experiment data. The numerical results show that the main failure modes of the composites under axial tensile load are pure matrix cracking, fiber and matrix tension failure in bias fiber tows, matrix tension failure in axial fiber tows and interface debonding; the main failure modes of the composites subjected to transverse tensile load are free-edge effect, matrix tension failure in bias fiber tows and interface debonding.     

Compressive properties of single-filament carbon fibres

Compressive properties of mesophase pitch-based carbon fibres (NT-20, NT-40 and NT-60) were measured using the tensile recoil test and the elastica loop test. The NT-40 fibre with a 400 GPa tensile modulus showed a smaller loop compressive yield strain and a larger recoil compressive strength compared to these values obtained from the longitudinal compression test on its unidirectional composites. Further, the recoil compressive strength of this fibre was higher than that of PAN-based carbon fibre with a corresponding modulus. Under the ideal conditions in the tensile recoil test, the strain energy was conserved before and after recoil, and the initial tensile stress and the recoil compressive stress do not coincide when fibre stress-strain behaviour is non-linear, and the non-linearity in compression and in tension is different. The difference between the composite compressive strength and the recoil compressive strength of NT-40 was quantitatively explained by taking account of the fibre compressive stress-strain non-linear relation. The difference between the loop compressive yield strain and the composite compressive strain to failure was also explained by this non-linearity.