Corrosion protection of AISI 316 stainless steel by ALD alumina/titania nanometric coatings

Stainless steels are used today in a wide range of applications as a result of their combination of high corrosion resistance and good mechanical properties. In some applications, for example, temporary contact biomedical devices or solar water heaters, corrosion resistance may need further improvement, and surface coatings may be applied for enhanced protection. In this study, AISI 316 stainless steel samples with two different standard industrial finishes were coated using atomic layer deposition (ALD) of Al₂O₃/TiO₂ layers. The morphology, composition and corrosion protection was then investigated using different techniques. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were used to obtain a morphological characterization of coatings and substrates. Glow discharge optical emission spectrometry (GDOES) was used to obtain an in-depth profile of composition. Polarization curves in a 0.2 M NaCl solution were used to evaluate the corrosion protection given by the coatings. The deposited ALD layers were found to be almost flawless. The measured RMS roughness values were compared before and after the ALD, and were around 50 and 370 nm for the two samples. GDOES profiles were strongly influenced by the roughness of the substrate. The corrosion protection obtained on AISI 316 stainless steel by the application of nanometric coatings proved to be very effective in reducing the passive region current density from 10^?7 to less than 10^?9 A/cm² and increasing the passive region potential interval from 0.8 to 1.3 V before breakdown.     

Corrosion protection coating containing polyaniline glass flake composite for steel

Corrosion protection of steel by glass flake (GF) containing coatings is widely used in marine atmosphere. Even though, the coatings containing glass flake are highly corrosion resistant, their performance is decreased due to the presence of pinholes and coating defects. It is well established that polyaniline containing coating is able to protect the pinhole defects in the coatings due to passivating ability of polyaniline. Hence a study has been made on the corrosion protection ability of steel using polyaniline-glass flake composite containing coating with 10% loading of glass flake in epoxy binder. The polyaniline glass flake composite (PGFC) was synthesized by chemical oxidation of aniline by ammonium persulphate in presence of glass flake. The corrosion protection ability of GF and PGFC containing coating on steel was found out by salt spray test and EIS test in 3% NaCl. In both the tests, the resistance value of the PGFC containing coating has remained at 10⁸-10⁹ Ω cm² where as for the GF containing coating, the resistance values decreased to 10⁵ Ω cm². The enhanced corrosion protection ability of the PGFC containing coating is due to the passivation ability of the polyaniline present in the coating.     

Effect of pore content and pH on the corrosion behavior of hydrophobic ceramic coatings

In this paper, superhydrophobic ceramic coatings were successfully prepared on stainless steel substrates (S304) by sol–gel method, and the effects of pore content and pH conditions on the corrosion resistance of hydrophobic ceramic coatings were studied. As the porosity increases, the contact angle of the coating increases. Among them, the contact angles of the coatings with 15% and 20% porosity in different pH solutions are all greater than 150°, achieving superhydrophobic surfaces. The contact angle results before and after corrosion show that the solution with a higher pH has a greater damage to the hydrophobicity of the coating. The corrosion resistance of the coatings was evaluated comparatively from polarization curves and electrochemical impedance spectroscopy. As the hydrophobicity improves, the corrosion resistance of the hydrophobic ceramic coating is enhanced. The impedance moduli at .01 Hz of the coating are 1.04 × 10³ times (pH 4), .13 × 10³ times (pH 7), and .74 × 10³ times (pH 10) of the bare steel, respectively. With the increase of pH, the corrosion resistance of hydrophobic ceramic coatings decreases, because OH⁻ in the corrosion solution is more easily adsorbed on the surface of the coating, thereby destroying the long hydrophobic chains.     

Molybdate‐doped copolymer coatings for corrosion prevention of stainless steel

The polypyrrole and polyaniline copolymer coating (PPy‐PAni) and PPy‐PAni doped with sodium molybdate copolymer coating ( ) were synthesized on stainless steel by cyclic voltammetry. The effect of molybdate on the passivation of stainless steel was investigated by linear sweep voltammetry in 0.2 mol L^?1 of oxalic acid. The corrosion prevention performances of these copolymer coatings for stainless steel were investigated by linear sweep voltammetry, electrochemical impedance spectroscopy in 1 mol L^?1 of sulfuric acid, and potentiodynamic polarization in 0.1 mol L^?1 of hydrochloric acid. Copolymer coating doped with molybdate could accelerate the formation of the passive oxide film and have better corrosion prevention efficiencies than PPy‐PAni coating on stainless steel. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40602.     

A comparative study to evaluate the corrosion performance of Zr incorporated Cr3C2-(NiCr) coating at 900 °C

In this study zirconium incorporated Cr₃C₂-(NiCr) coating has been sprayed on three superalloys viz. Superni 718, Superni 600 and Superco 605 using D-gun technique. A comparative study has been carried out to check the cyclic oxidation in air and hot corrosion in simulated incinerator environment (40%Na₂SO₄-40%K₂SO₄-10%NaCl-10%KCl) for the coated specimens at 900 °C for 100 cycles. Oxidation kinetics has been established for all the specimens using weight change measurements. Corrosion products have been characterized using X-ray diffractometer (XRD) and scanning electron microscopy/energy-dispersive analysis (SEM/EDAX). Cr₃C₂-(NiCr) + 0.2%wtZr coating provides very good corrosion resistance in air oxidation for all the three coated superalloys. As all the three coated superalloys shows parabolic behaviour with parabolic rate constant as 0.07 × 10^?10 (g² cm^?4 s^?1) for Superni 718, 0.43 × 10^?10 (g² cm^?4 s^?1) for Superni 600 and 0.3 × 10^?10 (g² cm^?4 s^?1) for Superco 605 This coating is also effective in the molten salt environment but coating on Co-based superalloy Superco 605 did not perform satisfactorily. The parabolic rate constants for coated Superni 718 is 0.61 × 10^?10 (g² cm^?4 s^?1), for coated Superni 600 is 6.72 × 10^?10 (g² cm^?4 s^?1) and for coated Superco 605 is 17.5 × 10^?10 (g² cm^?4 s^?1).     

Atomic force microscopy analysis of cathodic arc ion-plated CrN and CrC coatings

Coatings of CrN and CrC were deposited on a YT14 cemented carbide cutting tool using cathodic arc ion plating (CAIP). The surface and interface morphologies of the as-obtained CrN and CrC coatings were analyzed using a field emission scanning electron microscope. The heights, particle diameters and power spectral densities of CrN and CrC coatings were analyzed using atomic force microscopy and the correlated parameters of roughness were obtained. The results show that the roughness of the CrN and CrC coatings is 81.7 × 10^?3 and 70.2 × 10^?3 nm, respectively, and CAIP has little effect on the CrN and CrC coating roughness. The height of the peak values of CrN and CrC coatings is 0.498 and 0.502 nm, respectively, and the reduction friction of the CrN coating was slightly better than that of the CrC coating. The average particle diameter of the CrN and CrC coatings is 6.575 × 10² and 7.678 × 10² nm, respectively, and the particles are uniformly distributed with no large-scale fluctuations. The power between the cursors of the CrN and CrC coatings is 1.44 × 10^?2 and 9 × 10^?3 nm², respectively, with the power spectral density of the CrN coating being the dominant frequency.     

Corrosion protection of new composite polymer coating for carbon steel in sulfuric acid medium by electrochemical methods

In this paper, electropolymerization technique has been used for the obtained of new composite: polypyrrole – dioctyl sulfosuccinate sodium/poly N-ethylaniline (PPY-AOT/PNEA) coatings over carbon steel of type OLC 45 electrode for anticorrosion protection. The PPY-AOT/PNEA coatings were successfully synthesized onto OLC 45 electrode by galvanostatic deposition from aqueous solutions 0.1 M NEA, 0.1 M PY, 0.01 M AOT and 0.3 M H₂C₂O₄ solution at different current densities (5, 3 and 1 mA/cm²) in different molar ratio. The anionic surfactant (AOT) as a dopant ion used during electropolymerization can have a significant result on the anticorrosion protection of the composite film by hindering the penetration of aggressive ions. The polymeric composite coatings have been analyzed by cyclic voltammetry (CV), Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion resistance of PPY-AOT/PNEA coated carbon steel has been examined by potentiodynamic polarization techniques and electrochemical impedance spectroscopy (EIS) methods in 0.5 M H₂SO₄ solutions. The data of the corrosion samples demonstrated that PPY-AOT/PNEA coatings assure a great anticorrosion protection of OLC 45 electrode in corrosive media. The corrosion rate of PPY-AOT/PNEA coated OLC 45 has been indicated to be ~9 times lower than of uncoated electrode. The corrosion protection effectiveness of the composite coating is more than 89%. The best efficiency is accomplished of PPY-AOT/PNEA obtained by electrodeposition at 5 mA/cm² current densities applied in molar ratio 5:1.     

High temperature anti‐oxidation behavior of in situ and ex situ nanostructured C/SiC/ZrB2‐SiC gradient coatings: Thermodynamical evolution,microstructural characterization,and residual stress analysis

Nanostructured C/SiC/ZrB₂–SiC oxidation protective gradient coating was prepared by a two‐step reactive melt infiltration method. In order to reduce production cost, ZrB₂ phase was synthesized by the in situ reactive that included low‐cost ZrO₂ and B₂O₃ powders as raw materials. High‐temperature oxidation behavior of coatings was evaluated by isothermal oxidation test at 1773 K in air for 10 hours. Thermodynamical behavior of the coatings at various temperatures during oxidation test and coating process was predicted by HSC Chemistry 6.0 software. Compressive residual stresses of 36.9 MPa and 41 MPa were calculated for in situ and ex situ coatings by Williamson‐Hall method. After 10 hours of isothermal oxidation at 1773K, in situ and ex situ coatings showed 12.84% and 15.69% of weight losses with oxidation rates of 1.87 × 10^?2 g cm^?3 h^?1 and 0.91 × 10^?2 g cm^?3 h^?1, respectively. These results indicated that the oxidation protection ability of the coating produced by the in situ method was very close to ex situ coating.     

Corrosion protection by epoxy/poly(aniline-co-pyrrole)/ZnO nanocomposite coating

Anticorrosion behavior of epoxy/poly(aniline-co-pyrrole)/ZnO (EPAPZ) coating on stainless steel 304 alloys is investigated using the electrochemical impedance spectroscopy (EIS) method, and the coating is compared with epoxy/polyaniline/ZnO (EPAZ) and pure epoxy (EP) coatings. Scanning electron microscopy images are used for structural characterization and to compare the particle size of nanoparticles. EIS result showed that coating resistance for EPAPZ, EPAZ, and EP coatings after 90 days of immersion in 3.5% NaCl was 1.18 × 10⁷, 1.08 × 10⁶, and 4.28 × 10⁴ Ω cm⁻², respectively. In addition, the volume percentage of water absorbed by the coating, which could be obtained by coating capacitance, is 2.81, 4.21, and 9.11, respectively. Immersion tests showed 0.063, 0.194, and 0.752% of weight loss in the metals under EPAPZ, EPAZ, and EP coatings, respectively. These results show that the EPAPZ coating has superior anticorrosive performance compared with EPAZ and EP coatings. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48265.     

Polyaniline for corrosion prevention of mild steel coupled with copper

Polyaniline emeraldine base/epoxy resin (EB/ER) coating was investigated for corrosion protection of mild steel coupled with copper in 3.5% NaCl solution. EB/ER coating with 5-10 wt% EB had long-term corrosion resistance on both uncoupled steel and copper due to the passivation effect of EB on the metal surfaces. During the 150 immersion days, the impedance at 0.1 Hz for the coating increased in the first 1-40 days and subsequently remained constant above 10⁹ Ω cm², whereas that for pure ER coating fell below 10⁶ Ω cm² after only 30 or 40 days. Immersion tests on coated steel-copper galvanic couple showed that EB/ER coating offered 100 times more protection than ER coating against steel dissolution and coating delamination on copper, which was mainly attributed to the passive metal oxide films formed by EB blocking both the anodic and cathodic reactions. Salt spray tests showed that 100 μm EB/ER coating protected steel-copper couple for at least 2000 h.     

Tribological and corrosion behaviors of fluorocarbon coating reinforced with sodium iron titanate platelets and whiskers

A series of sodium iron titanate (NFTO)–fluorocarbon composite coatings have been prepared with the liquid-phase blending method. The effects of two types of NFTO, NFTO platelets, and NFTO whiskers, on the tribological and corrosion behaviors of the composite coatings, are systematically studied. The results show that the addition of NFTO can significantly enhance the friction-reducing and wear resistance performances of the fluorocarbon coating. Under dry sliding, the minimum specific wear rate is 1.67 × 10⁻⁴ mm³/Nm for the platelet-filled composite coatings and 1.15 × 10⁻⁴ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 83.5 and 88.6% than that of pure coating. Under a simulated seawater environment, the minimum specific wear rate is 5.44 × 10⁻⁵ mm³/Nm for the platelet-filled composite coatings and 0.84 × 10⁻⁵ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 90.5 and 98.5% than that of pure coating. The morphologies of worn surfaces, wear debris, and transfer films are analyzed, and the corresponding wear resistance mechanisms are discussed. The electrochemical impedance spectroscopy certifies a remarkably improved corrosion resistance of the composite coatings which have been immersed in 3.5 wt % NaCl solution for 30 days. The composite coating reinforced with 7.5 wt % platelets shows the highest resistance of 256.3 × 10⁶ Ω·cm², approximately two orders of magnitude higher than that of pure coating. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48936.     

A new corrosion protection coating with polyaniline-TiO2 composite for steel

Organic coating strategies for corrosion protection with inherently conducting polymers have become important because of restriction on the use of heavy metals and chromates in coatings due to their environmental problems. This work presents the synthesis of polyaniline-TiO₂ composites (PTC) and the corrosion protection behaviour of PTC containing coating on steel. PTC was prepared by chemical oxidation of aniline and TiO₂ by ammonium persulfate in phosphoric acid medium. The PTC was characterized by FTIR, XRD and SEM techniques. Suitable coating with PTC was formed on steel using acrylic resin. Using electrochemical impedance spectroscopy, the PTC containing coating's behaviour in 3% NaCl immersion test and salt spray test has been found out. Results indicate that the coating containing PTC is able to maintain the potential of steel in passive region due to its redox property. The resistance of the coating containing PTC was more than 10⁷ Ω cm² in 3% NaCl solution after 60 days and 10⁹ Ω cm² in the salt spray test of 35 days. But the resistance of the TiO₂ containing coating was found to be less than 10⁴ Ω cm² in both the cases. The high performance of PTC containing coating is attributed to the passivation of steel by polyaniline.     

Corrosion protection by zirconia-based thin films deposited by a sol–gel spin coating method

This paper focuses on the structure and corrosion behavior of 316L stainless steel coated by inorganic ZrO₂, hybrid ZrO₂–PMMA, and combined inorganic–hybrid films. The coatings were deposited by a particulate sol–gel spin-coating route, using carboxymethyl cellulose as a nanoparticle dispersant. The electrochemical evaluations were conducted in a simulated body fluid, via potentiodynamic polarization and impedance spectroscopic experiments. According to the results, the hybrid coating presented a better corrosion protection compared to the inorganic coating, due to a lesser density of structural defects. However, the best corrosion resistance was found for a combined coating which consists of an inorganic bottom layer and a hybrid top layer, due to a desirable compromise of good adhesion and low defect density.     

Novel surfactant-free waterborne acrylic-silicone modified alkyd hybrid resin coatings containing nano-silica for the corrosion protection of carbon steel

We report a novel waterborne acrylic-silicone modified alkyd nanocomposite latex containing nano-silica prepared by the surfactant-free miniemulsion polymerization. The influences of γ-methacryloxy-propyltrimethoxysilane- (MPS-) modified nano-silica particle contents to the thermal, mechanical and anti-corrosion performance of hybrid latex coatings were studied. The results revealed that the incorporation of nano-silica particles into latex films could directly increase the thermal stability and mechanical properties. Electrochemical corrosion studies revealed that these nanocomposite coatings exhibited superior corrosion resistance performance (inhibition efficiency 99.36% and corrosion rate 1.09 × 10 ^?3 mm per year) than that of the control system (without SiO₂ NPs).     

High strain rate compressive behavior of PMMA

Polymethylmethacrylate (PMMA) materials are extensively used for diverse applications e.g., protective vehicular windows to eye protection devices. However, the high strain rate deformation and fracture mechanisms of PMMA are far from well understood. Therefore, controlled split Hopkinson pressure bar (SHPB) experiments that could lead to deformation with and without fracture were conducted on PMMA samples at strain rates of ~4 × 10⁰ to 1.3 × 10³ s^?1. With increase in strain rate, the maximum compressive yield strength of PMMA is enhanced by about 25 %. Absence of global failure characterized the deformation at relatively lower strain rates (e.g., ~4.75 × 10² to 6.75 × 10² s^?1), while its marked presence characterized the same at comparatively higher strain rates (e.g., ~7.69 × 10² to 9.31 × 10² s^?1). Attempts were made to explain these observations by the subtle changes in failure mechanisms as revealed from the fractographic examinations of the PMMA samples deformed with and without failures. The implications of the test-condition induced restrictions on the degrees of freedom locally available to the polymeric chains were discussed in the perspective of the relative strain rate dependencies of the yield behaviors of the present PMMA samples.     

The Fabrication and Characterization of Cellulose/Mesoporous Silica Composites Packaging Films with Adjustable Permeability by NMMO Technology

Cellulose-based composites containing various amounts of SBA-15 mesoporous silica were prepared by NMMO-technology, and their morphologies, mechanical properties, permeability for oxygen and water vapor were studied. The investigation suggested that both the modified and unmodified mesoporous silica materials can improve the elongation at break of the cellulose films. However, the incorporation of the mesoporous silica materials can reduce the tensile strength of the films, and the modified one has less effect on that than the unmodified one. The composites films with rational mechanical properties have adjustable oxygen permeability (7.90 × 10^?15–94.6 × 10^?15 cm³ · cm/cm² · s · Pa) and water vapor permeability (7.12 × 10^?13–4.10 × 10^?13 g · cm/cm² · s · Pa).     

New potassium sodium niobate/poly(vinylidene fluoride) functional composite films with high dielectric permittivity

New and homogeneous KNN/PVDF functional hybrid films loaded with 2 vol.%, 4 vol.%, 9 vol.%, 21 vol.%, 30 vol.%, and 40 vol.% Na_0.5K_0.5NbO₃ (KNN) have been prepared by a solution casting process. The effects of the doping KNN particles on the structure, morphology, and dielectric properties of KNN/PVDF hybrid films were investigated. The introduction of KNN fillers has a remarkable influence on the α-, β-, γ-phase structure and the crystallinity of the polymer matrix. And it is also effective in improving the dielectric performance. A dielectric permittivity as high as 250 is obtained at 10 Hz when the concentration of the KNN filler reaches 30 vol.%, which is 28 times higher than that of the pure PVDF matrix. The conductivity of the hybrid film with 40 vol.% KNN concentrations is lower than 8 × 10^?10 (S cm^?1) at 10² Hz and at room temperature, which shows its excellent insulativity and the potential to be applied into the electronic industry.     

Corrosion behavior of carbon steel coated with magnesium electrodeposited from methyl magnesium chloride solution

Magnesium coating was electroplated on carbon steel to improve its corrosion protection. The analytical characterization of the magnesium coating was performed by scanning electron spectroscopy and energy dispersive X-ray spectroscopy. The electrochemical behavior of Mg-coated carbon steel was assessed by electrochemical impedance spectroscopy, open-circuit potential measurements and potentiodynamic polarization curves in 0.03% sodium chloride solution. The electrochemical results showed that the self-corrosion current density (i _corr) of magnesium-coated steel was 0.32 mA cm^?2 (about 1.8% of that of uncoated steel). Impedance results showed an increase of the total impedance when magnesium coating was applied on steel substrate. The corrosion protection was ensured by a two-step mechanism. The first step was cathodic polarization; the second step was the formation of a barrier due to magnesium oxides composed of MgO, Mg(OH₂) and Mg(OH₃)Cl.     

Dielectric and electrical characterization of (PEO–PMMA)–LiBF<Subscript>4</Subscript>–EC plasticized solid polymer electrolyte films

Plasticized solid polymer electrolytes (PSPEs) consisting of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend (50/50 wt%) based matrix with lithium tetrafluoroborate (LiBF₄) as dopant ionic salt (10 wt%) and varied concentrations (x = 0, 5, 10 and 15 wt%) of ethylene carbonate (EC) as plasticizer have been prepared. Classical solution-cast (SC) and the ultrasonic assisted followed by microwave irradiated (US–MW) solution-cast methods have been used for the preparation of (PEO–PMMA)–LiBF₄–x wt% EC films, and the same have been hot–pressed to get their smooth surfaces. Dielectric relaxation spectroscopy (DRS) and X–ray diffraction (XRD) techniques have been employed to characterize the dielectric and electrical dispersions and the structural properties of the PSPE films, respectively. It has been observed that the ionic conductivity of these semicrystalline ion-dipolar complexes is governed by their dielectric permittivity and polymers chain segmental dynamics. The increase in ionic conductivity values with the increase of plasticizer concentration in the PSPEs also varies with the films’ preparation methods. The US–MW method prepared PSPE film containing 15 wt% EC has a maximum ionic conductivity (1.86 × 10^?5 S cm^?1) at room temperature, whereas, the films having low concentrations of EC exhibit the conductivity of the order of 10^?6 S cm^?1.     

Advanced antistatic/anticorrosion coatings prepared from polystyrene composites incorporating dodecylbenzenesulfonic acid‐doped SiO2@polyaniline core–shell microspheres

We present the preparation of advanced antistatic and anticorrosion coatings of polystyrene (PS) incorporating a suitable amount of dodecylbenzenesulfonic acid (DBSA)‐doped SiO₂@polyaniline (SP) core–shell microspheres. First, aniline‐anchored SiO₂ (AS) microspheres that were about 850 nm in diameter were synthesized using the conventional base‐catalyzed sol–gel process with tetraethyl orthosilicate in the presence of N‐[3‐(trimethoxysilyl)propyl]aniline. SP core–shell microspheres were then synthesized by chemical oxidative polymerization of aniline monomers with ammonium persulfate as an oxidizing agent in the presence of the AS microspheres. The polyaniline shell thickness of the as‐prepared core–shell microspheres was estimated to be about 120 nm. The AS and SP microspheres were further characterized using Fourier transform infrared spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy. The as‐synthesized DBSA‐doped SP core–shell microspheres were then blended into PS using N‐methyl‐2‐pyrrolidone as solvent and then cast onto a cold–rolled steel (CRS) electrode to obtain antistatic and anticorrosion coatings with a thickness of about 10 µm. The corrosion protection efficiency of the as‐prepared coating materials on the CRS electrode was investigated using a series of systematic electrochemical measurements under saline conditions. The enhanced corrosion protection ability of the PS/SP composite coatings may be attributed to the formation of a dense passive metal oxide layer induced by the redox catalytic effect of the polyaniline shell of the as‐synthesized core–shell microspheres, as evidenced by electron spectroscopy for chemical analysis and SEM observations. Moreover, the PS composite coating containing 10 wt% of the SP core–shell microspheres showed an electrical resistance of about 3.65 × 10⁹Ω cm^?2, which meets the requirements for antistatic applications. Copyright © 2012 Society of Chemical Industry