Electrochemical oxidation of an acid dye by active chlorine generated using Ti/Sn<Subscript>(1−<Emphasis Type="Italic">x</Emphasis>)</Subscript>Ir<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>2</Subscript> electrodes

The generation of active chlorine on Ti/Sn_(1−x)Ir _x O₂ anodes, with different compositions of Ir (x = 0.01, 0.05, 0.10 and 0.30 ), was investigated by controlled current density electrolysis. Using a low concentration of chloride ions (0.05 mol L⁻¹) and a low current density (5 mA cm⁻²) it was possible to produce up to 60 mg L⁻¹ of active chlorine on a Ti/Sn_0.99Ir_0.01O₂ anode. The feasibility of the discoloration of a textile acid azo dye, acid red 29 dye (C.I. 16570), was also investigated with in situ electrogenerated active chlorine on Ti/Sn_(1−x)Ir _x O₂ anodes. The best conditions for 100% discoloration and maximum degradation (70% TOC reduction) were found to be: NaCl pH 4, 25 mA cm⁻² and 6 h of electrolysis. It is suggested that active chlorine generation and/or powerful oxidants such as chlorine radicals and hydroxyl radicals are responsible for promoting faster dye degradation. Rate constants calculated from color decay versus time reveal a zero order reaction at dye concentrations up to 1.0 × 10⁻⁴ mol L⁻¹. Effects of other electrolytes, dye concentration and applied density currents also have been investigated and are discussed.     

Structural characterization and superconducting properties of MgB<Subscript>2</Subscript> prepared by SHS-method

Self-propagating high-temperature synthesis (SHS) of bulk MgB₂ superconductor from Mg-2B powder blend is reported. This reaction proceeds violently at 100 A under a protective atmosphere. Since the heat of reaction of Mg and B was not enough for chain reaction, then (Ti + C) mixed powders were used as the ignition agent to assist the reaction (Mg + 2B). In this case, the combustion front moved without any difficulty. The diffraction lines of the product can be indexed to a hexagonal MgB₂ phase, with lattice constants a = 3.0845 Å, and c = 3.5259 Å. For comparison, the direct synthesis of (Mg + 2B) mixture was carried out at (800°C–1000°C). It can be found, that high-temperature sintering (1000°C) will induce the formation of impurities. The MgB₂ grains are fine, well compacted and more homogenous. The structure of materials was studied using XRD, FESEM and EDX. M-H curvatures were measured under the magnetic fields between ?80 kOe and 80 kOe. J _c was calculated from width of magnetization hysteresis loops based on the extended Bean Model.     

Synthesis of cathode material LiNi<Subscript>1-<Emphasis Type="Italic">y</Emphasis></Subscript>Co<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>O<Subscript>2</Subscript> by a simplified combustion method

The optimum conditions for synthesizing LiNi_1-y Co _y O₂ (y=0.1, 0.3 and 0.5) by a simplified combustion method, in which the preheating step is omitted, and the electrochemical properties of these materials were investigated. The optimum condition for synthesizing LiNi_0.9Co_0.1O₂ by the simplified combustion method is calcination at 800 °C for 12 h in air in 3.6 mole ratio of urea to nitrate. The LiNi_0.9Co_0.1O₂ synthesized under these conditions shows the smallest R-factor{(I ₀₀₆+I ₁₀₂)/I ₁₀₁} and the largest I ₀₀₃/I ₁₀₄, indicating better hexagonal ordering and less cation mixing, respectively. The LiNi_0.7Co_0.3O₂ synthesized at 800 °C for 12 h in air in 3.6 mole ratio of urea to nitrate has the largest first discharge capacity 156.2 mA h g⁻¹ at 0.5C and shows relatively good cycling performance. This sample shows better hexagonal ordering and less cation mixing than the other samples. The particle size of the LiNi_0.7Co_0.3O₂ is relatively small and its particles are spherical with uniform particle size.     

Combustion synthesis of Mo<Subscript>5</Subscript>Si<Subscript>3</Subscript> in chemical furnace

The combustion synthesis of Mo₅Si₃ was carried out in a chemical furnace using 5Ti + 3Si mixtures as a chemical fuel. The synthesized single phase Mo₅Si₃ exhibited a spatial network microstructure and angular texture of crystals. The chemical composition and crystal morphology of intermediate phases suggest that the formation of Mo₅Si₃ occurs via dissolution of Mo in the Si melt followed by reactive diffusion in the supersaturated “liquid Si-Mo melt-solid Mo” system.      

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

Catalytic Wet Oxidation of H<Subscript>2</Subscript>S to Sulfur on V/MgO Catalyst

The V/MgO catalysts with different V₂O₅ loadings were prepared by impregnating MgO with aqueous vanadyl sulfate solution. All of the catalysts were characterized by X-ray diffraction (XRD), temperature-programmed reduction (TPR), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). It was observed that the H₂S removal capacity with respect to vanadia content increased up to 6 wt%, and then decreased with further increase in vanadia loading. The prepared catalysts had BET surface areas of 11.3 ~ 95.9 m²/g and surface coverages of V₂O₅ of 0.1 ~ 2.97. The surface coverage calculation of V₂O₅ suggested that a vanadia addition up to a monomolecular layer on MgO support increased the H₂S removal capacity of V/MgO, but the further increase of VO _x surface coverage rather decreased that. Raman spectroscopy showed that the small domains of Mg₃(VO₄)₂ could be present on V/MgO with less than 6 wt% vanadia loading. The crystallites of bulk Mg₃(VO₄)₂ and Mg₂(V₂O₇) became evident on V/MgO catalysts with vanadia loading above 15 wt%, which were confirmed by a XRD. The TPR experiments showed that V/MgO catalysts with the loading below 6 wt% V₂O₅ were more reducible than those above 15 wt% V₂O₅. It indicated that tetrahedrally coordinated V⁵⁺ in well-dispersed Mg₃(VO₄)₂ domains could be the active species in the H₂S wet oxidation. The XPS studies indicated that the H₂S oxidation with V/MgO could proceed from the redox mechanism (V⁵⁺ V⁴⁺) and that V³⁺ formation, deep reduction, was responsible for the deactivation of V/MgO.     

Effects of K<Subscript>4</Subscript>Fe(CN)<Subscript>6</Subscript> on electroless copper plating using hypophosphite as reducing agent

K₄Fe(CN)₆ was used to improve the microstructure and properties of copper deposits obtained from hypophosphite baths. In electroless copper plating solutions using hypophosphite as the reducing agent, nickel ions (0.0038 M with Ni²⁺/Cu²⁺ mole ratio 0.12) was used to catalyze hypophosphite oxidation. However, the color of the copper deposits was dark or brown and its resistivity was much higher than that obtained in formaldehyde baths. The effects of K₄Fe(CN)₆ on the deposit composition, resistivity, structure, morphology and the electrochemical reactions of hypophosphite (oxidation) and cupric ion (reduction) have been investigated. The deposition rate and the resistivity of the copper deposits decreased significantly with the addition of K₄Fe(CN)₆ to the plating solution and the color of the deposits changed from dark-brown to copper-bright with improved uniformity. The nickel and phosphorus content in the deposits also decreased slightly with the use of K₄Fe(CN)₆. Smaller crystallite size and higher (111) plane orientation were obtained by addition of K₄Fe(CN)₆. The electrochemical current–voltage results show that K₄Fe(CN)₆ inhibited the catalytic oxidation of hypophosphite at active nickel sites and reduced the reduction reaction of cupric ions on the deposit surface by adsorption on the electrode. This results in lower deposition rate and a decrease in the mole ratio of NaH₂PO₂/CuSO₄ consumed during plating.     

Synergism Between Pt/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Au/TiO<Subscript>2</Subscript> in the Low Temperature Oxidation of Propene

CO impedes the low temperature (<170 °C) oxidation of C₃H₆ on supported Pt. Supported Au catalysts are very effective in the removal of CO by oxidation, although it has little propene oxidation activity under these conditions. Addition of Au/TiO₂ to Pt/Al₂O₃ either as a physical mixture or as a pre-catalyst removes the CO and lowers the light-off temperature (T ₅₀) for C₃H₆ oxidation compared with Pt catalyst alone by ~54 °C in a feed of 1% CO, 400 ppm C₃H₆, 14% O₂, 2% H₂O.     

Investigation of a new lead-free Bi<Subscript>0.5</Subscript>(Na<Subscript>0.40</Subscript>K<Subscript>0.10</Subscript>)TiO<Subscript>3</Subscript>-(Ba<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>)TiO<Subscript>3</Subscript> piezoelectric ceramic

Lead-free piezoelectric compositions of the (1-x)Bi_0.5(Na_0.40K_0.10)TiO₃-x(Ba_0.7Sr_0.3)TiO₃ system (when x = 0, 0.05, 0.10, 0.15, and 0.20) were fabricated using a solid-state mixed oxide method and sintered between 1,050°C and 1,175°C for 2 h. The effect of (Ba_0.7Sr_0.3)TiO₃ [BST] content on phase, microstructure, and electrical properties was investigated. The optimum sintering temperature was 1,125°C at which all compositions had densities of at least 98% of their theoretical values. X-ray diffraction patterns that showed tetragonality were increased with the increasing BST. Scanning electron micrographs showed a slight reduction of grain size when BST was added. The addition of BST was also found to improve the dielectric and piezoelectric properties of the BNKT ceramic. A large room-temperature dielectric constant, ε _r (1,609), and piezoelectric coefficient, d ₃₃ (214 pC/N), were obtained at an optimal composition of x = 0.10.     

Quasi-crystalline Al<Subscript>70</Subscript>Cu<Subscript>20</Subscript>Fe<Subscript>10</Subscript> by thermal explosion: Effect of AlCu doping on magnetic properties

Polycrystalline quasi-crystals of icosahedral Al₇₀Cu₂₀Fe₁₀(i-Al₇₀Cu₂₀Fe₁₀) were prepared by thermal explosion (TE) of mechanically activated mixture of Al, Cu, Fe powders doped with AlCu. The effect of AlCu dopant was studied by XRD, field emission scanning electron (FESEM), optical microscopy (OM), atomic emission spectroscopy (AES), and energy-dispersive X-ray microanalysis (EDX). The synthesized i-Al₇₀Cu₂₀Fe₁₀ and intermetallics (Al₃Fe, Al₂Cu) show soft ferromagnetic and paramagnetic properties, respectively.      

Performance of Ni catalyst supported on La-hexaaluminate in CO<Subscript>2</Subscript> reforming of CH<Subscript>4</Subscript>

CO₂ reforming of CH₄ was performed using Ni catalyst supported on La-hexaaluminate which has been an well-known material for high-temperature combustion. La-hexaaluminate was synthesized by sol-gel method at various conditions where different amount of Ni (5–20 wt%) was loaded. Ni/La-hexaaluminate experienced 72 h reaction and its catalytic activity was compared with that of Ni/Al₂O₃, Ni/La-hexaaluminate shows higher reforming activity and resistance to coke deposition compared to the Ni/Al₂O₃ model catalyst. Coke deposition increases proportionally to Ni content. Consequently, Ni(5)/La-hexaaluminate(700) is the most efficient catalyst among various Ni/La-hexaaluminate catalysts regarding the cost of Ni in Ni(X)/La-hexaaluminate catalysts. BET surface area, XRD, EA, TGA and TPO were performed for surface characterization. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Effect of heat release conditions on the phase composition of the combustion products of a Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Al/C thermite mixture

An X-ray method was used to study the phase composition of the combustion products of a Fe₂O₃/TiO₂/Al/C thermite composite mixture, in particular, during combustion of samples under cooling by water. The data of the experiments are compared with the results of thermodynamic calculations. A probable explanation of the reasons of the angular displacement of the line of iron in the X-ray spectrum of the combustion products and a mechanism for the crystallization of an eutectic TiC + α-Fe mixture from the melt of the Ti/Fe/C ternary system. The composition of the combustion products was found to be different from the equilibrium one, which is manifested in the presence of defects in the carbon sublattice of titanium carbide. A probable explanation of the deficiency of carbon is proposed. __________ Translated from Fizika Goreniya i Vzryva, Vol. 44, No. 4, pp. 39–43, July–August, 2008.     

Syndiospecific Polymerization of Styrene Using Half-Titanocene Catalyst Covalently Supported on MgCl<Subscript>2</Subscript>/AlEt<Subscript>n</Subscript>(OEt)<Subscript>3-n</Subscript>

The novel half-titanocene catalyst bearing reactive functional amino group, η⁵-pentamethylcyclopentadienyltri(p-amino-phenoxyl) titanium [Cp^∗Ti(p-OC₆H₄NH₂)₃], was easily synthesized by the reaction of η⁵-pentamethylcyclopentadienyltrichloride titanium (Cp^∗TiCl₃) with p-amino phenol in the presence of triethyl amine (NEt₃). Cp^∗Ti(p-OC₆H₄NH₂)₃ covalently anchored on MgCl₂/AlEt_n(OEt)_3-n support obtained from the reaction of triethylaluminium (AlEt₃) with the adduct of magnesium chloride (MgCl₂) and ethanol (EtOH), has been investigated and used to catalyze syndiospecific polymerization of styrene. Influences of the support structure, cocatalyst, and the molar ratio of Al in methylaluminoxane (MAO) and Ti (Al_MAO/Ti) on catalytic activity, syndiotacticity and molecular weight of the resultant polystyrene were investigated. Compared with the corresponding Cp^∗Ti(p-OC₆H₄NH₂)₃ homogeneous catalyst, a considerable increase in activity and molecular weight of syndiotactic polystyrene (sPS) was observed for the Cp^∗Ti(p-OC₆H₄NH₂)₃-MgCl₂/AlEt_n(OEt)_3-n supported catalyst even at a relatively low Al_MAO/Ti ratio of 50, and the kinetics of polymerization was stable during the reaction process.     

Synthesis of Heterogeneous Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> Nanostructured Anodes with Long-Term Cycle Stability

The 0D-1D Lithium titanate (Li₄Ti₅O₁₂) heterogeneous nanostructures were synthesized through the solvothermal reaction using lithium hydroxide monohydrate (Li(OH)·H₂O) and protonated trititanate (H₂Ti₃O₇) nanowires as the templates in an ethanol/water mixed solvent with subsequent heat treatment. A scanning electron microscope (SEM) and a high resolution transmission electron microscope (HRTEM) were used to reveal that the Li₄Ti₅O₁₂ powders had 0D-1D heterogeneous nanostructures with nanoparticles (0D) on the surface of wires (1D). The composition of the mixed solvents and the volume ratio of ethanol modulated the primary particle size of the Li₄Ti₅O₁₂ nanoparticles. The Li₄Ti₅O₁₂ heterogeneous nanostructures exhibited good capacity retention of 125 mAh/g after 500 cycles at 1C and a superior high-rate performance of 114 mAh/g at 20C.     

Combustion of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Al thermit mixtures in steel tubes

Explored was the combustion of Fe₂O₃/TiO₂/Al thermit mixtures in steel tubes upon variation in green composition and with special emphasis on the dependence of combustion temperature T _c and burning velocity U on reaction heat Q. Special attention was given to incompleteness of combustion for compositions with low Q.     

The Oxidative Polycondensation of Benzylidene-4′-hydroxyanilene using Air O<Subscript>2</Subscript>, NaOCl and H<Subscript>2</Subscript>O<Subscript>2</Subscript>: Synthesis and Characterization

In this work, the oxidative polycondensation reaction conditions of benzylidene-4′-hydroxyanilene (B-4′-HA) were studied using oxidants such as air O₂, H₂O₂ and NaOCl in an aqueous alkaline medium between 40 and 95 ^○C. Oligo-benzylidene-4′-hydroxyanilene was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. The solubility of oligomer using organic solvents such as DMF, THF, DMSO, methanol, ethanol, CHCl₃, CCl₄, toluene, acetonitrile, ethyl acetate was investigated. According to air O₂ oxidant (flow rate 8.5 L/h), the conversion of B-4′-HA was 82.0% in optimum conditions such as [B-4′-HA]₀=[KOH]₀=0.1015 mol/L at 50 ^○C for 25 h. According to the SEC analysis, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of O-B-4′-HA were found to be 1852 g mol⁻¹, 3101 g mol⁻¹ and 1.675; 2123 g mol⁻¹, 4073 g mol⁻¹ and 1.919; 2155 g mol⁻¹, 4164 g mol⁻¹ and 1.932, using air oxygen, NaOCl and H₂O₂ oxidants, respectively. Also, Thermo gravimetric analysis (TGA) showed oligo-benzylidene-4′-hydroxyanilene to be unstable against thermo-oxidative decomposition. The weight loss of O-B-4′-HA was found to be 95.87% at 1000 ^○C.     

Mechanistic Investigation of Co Containing NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Traps

Co-containing NO _x storage and reduction catalysts were investigated to identify the mechanism of Co promotion. X-ray diffraction and temperature programmed reduction demonstrated that Co exists in a highly oxidized state (Co₃O₄) and that the surface oxygen could be removed from the catalyst a typical operating conditions around 300 °C. Electron microscopy showed that Co is more uniformly distributed over the catalyst surface, as compared to Pt, with particle sizes ranging between 20 and 80 nm. In situ IR studies illustrated that NO _x storage occurs on Co-containing NSR catalyst via formation of nitrites and nitrates as surface intermediates. Finally, it was found that, similar to Pt, the addition of Co to Ba catalysts enhances the nitrite to nitrate transition rate and also increases the overall formation of nitrates. Therefore, the promotional effect shown by Co is the result of the combination of increased NO to NO₂ oxidation and improved surface area for NO₂ spillover to the Ba storage sites.     

Formation of organic-inorganic composite materials based on cellulose <Emphasis Type="Italic">Acetobacter xylinum</Emphasis> and calcium phosphates for medical applications

The formation of composites based on the cellulose Acetobacter xylinum and calcium phosphates has been investigated using X-ray diffraction, electron diffraction, electron microscopy, energy-dispersive analysis, and differential scanning calorimetry. It has been demonstrated that the planar morphology of calcium phosphate nanoparticles capable of interacting with nanofibrils of the cellulose matrix is an important factor providing interfacial contacts in the formation of organic-inorganic composite materials. It has been established that magnesium-containing calcium phosphates represent two-phase systems consisting of calcium magnesium phosphate Ca_2.6Mg_0.4(PO₄)₂ (whitlockite) and hydroxyapatite Ca₅(PO₄)₃(OH). The biocompatibility of the composite materials based on two-phase calcium phosphate systems and the temperature range of their stability (∼20–250°C) determined by the thermal stability of the organic component have been investigated.     

Photoluminescence characteristics of Cd<Subscript>1-<Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Te single crystals grown by the vertical Bridgman method

In this paper, we report a systematic investigation of band-edge photoluminescence for Cd_1-x Mn _x Te crystals grown by the vertical Bridgman method. The near-band-edge emissions of neutral acceptor-bound excitons (labeled as L1) were systematically investigated as a function of temperature and of alloy composition. The parameters that describe the temperature variation of the energy were evaluated by the semiempirical Varshni relation. From the temperature dependence of the full width at half maximum of the L1 emission line, the broadening factors Γ(T) were determined from the fit to the data. The activation energies of thermal quenching were obtained for the L1 peak from the temperature dependence of the bound exciton peaks and were found to decrease with increasing Mn concentration.     

Comparison of Two Preparation Methods in the Redox Properties of Pd/CeO<Subscript>2</Subscript>/Ta/Si Model Catalysts: Spin Coating Versus Sputter Deposition

Pd/CeO₂/Ta/Si model catalysts were prepared by spin coating and sputter deposition method, and characterized by means of AFM, SEM and in situ XPS, especially focusing on the redox properties of Ce and Pd elements. Compared with thin CeO₂ films (about 2.2nm), the thicker ones (about 22nm) maintained Ce⁴⁺ oxidation state even after treatment with H₂ up to 500°C while the presence of Pd facilitated the reduction of ceria. The reduction of ceria brought about following that of PdO, which was explained by the spillover of hydride in Pd to CeO₂ originating from hydrogen adsorption on the Pd surface. Compared with the sputter deposition method, spin coating produced the smaller size of Pd particles, thus leading to formation of the stable PdO species against hydrogen. Based on these results, a schematic model of Pd/CeO₂/Ta/Si was suggested and it might be assumed that spin coating method provided with an environment similar to the conventional impregnation.