Physical aging and thermal aging resistance of polycarbonate/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) blends

The effect of thermal annealing on the mechanical properties of polycarbonate (PC) was investigated by tensile testing, Izod impact testing, and differential scanning calorimetry (DSC). An endothermic peak appeared in the DSC curve by annealing at various temperatures below T_g. The peak area, as a measure of the degree of physical aging, increased with annealing time. The Izod impact strength decreased suddenly just before an endothermic peak became detectable. The results imply that at the very early stage of physical aging, a trigger for the ductile‐to‐brittle transition may be initiated. By blending hydrogenated styrene‐butadiene‐styrene block copolymer (SEBS), the embrittlement by annealing was prevented. That is, in the PC/SEBS blends, the physical aging of PC matrix proceeded in the same way as in neat PC; however, the Izod impact strength did not decrease. This thermal aging resistance seems to originate from the negative pressure effect of SEBS particles that provides dilational stress fields for PC matrix to enhance the local segment motions. POLYM. ENG. SCI., 52:1958–1963, 2012. © 2012 Society of Plastics Engineers     

Tailored dielectric and mechanical properties of noncovalently functionalized carbon nanotube/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) nanocomposites

The preparation of high‐dielectric poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) composites containing functionalized single‐walled carbon nanotubes (f‐SWCNTs) noncovalently appended with dibutyltindilaurate are reported herein. Transmission electron microscopy and X‐ray photoelectron and Raman spectroscopy confirmed the noncovalent functionalization of the SWCNTs. The SEBS‐f‐SWCNT composites exhibited enhanced mechanical properties as well as a stable and high dielectric constant of approximately 1000 at 1 Hz with rather low dielectric loss at 2 wt% filler content. The significantly enhanced dielectric property originates from the noncovalent functionalization of the SWCNTs that ensures good dispersion of the f‐SWCNTs in the polymer matrix. The f‐SWCNTs also acted as a reinforcing filler, thereby enhancing the mechanical properties of the composites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐ b‐styrene] on dielectric,thermal, and morphological characteristics of polypropylene/silica nanocomposites

The effect of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) copolymer on the thermal and dielectric properties of polypropylene (PP)—nanosilica (NS) composites in relation with morphological aspects revealed by atomic force microscopy (AFM) was investigated in this article. SEBS hindered the crystallization process of PP in PP/NS composites, leading to a smaller degree of crystallinity and lower perfection of crystalline structure. Broader lamellar thickness distribution was obtained in nanocomposites containing SEBS. Almost two times higher dielectric loss as compared to PP reference and two relaxation processes were detected in ε_r ^′′(f) curves of nanocomposites. The first peak, in the same frequency domain as for the references, was assigned to α‐relaxation of polymer components together with interfacial polarization. The relaxation time follows the Arrhenius law with an activation energy of 80–90 kJ/mol. For the second process, the temperature dependence of the relaxation times obeyed the VFT equation. The dielectric changes following the incorporation of SEBS support its tendency to hinder the motional processes in PP, in accordance with DSC results. A smooth transition from a phase rich in SEBS to one containing mainly PP was detected in the AFM image of the composite with the larger amount of SEBS, emphasizing the good compatibility at the PP/SEBS interface. POLYM. ENG. SCI., 53:2081–2092, 2013. © 2013 Society of Plastics Engineers     

Effect of poly [styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) and maleic anhydride‐grafted SEBS triblock copolymers in immiscible blends of (polyamide‐6)/polycarbonate: Morphology‐mechanical properties relationships

The effects of using maleated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS‐g‐MAH) and unmodified SEBS (unSEBS) on the phase morphology and mechanical properties of immiscible polymer blends of polyamide‐6 (PA‐6) and polycarbonate (PC) are investigated. Different binary, ternary, and quaternary blends were prepared by using a Brabender® co‐rotating twin‐screw extruder. The weight ratio of unSEBS to SEBS‐g‐MAH was changed to probe the phase morphology and mechanical properties. The results revealed that the mechanical properties of (PA‐6)/PC/(unSEBS/SEBS‐g‐MAH) blends were considerably governed by the unSEBS to SEBS‐g‐MAH weight ratio. Morphological investigation based on the spreading coefficient concept confirmed the results of scanning electron microscopy, indicating encapsulation of unSEBS domains around the PC core‐forming component in the presence of reactive SEBS‐g‐MAH precursor. Moreover, larger unSEBS‐PC composite droplets appeared throughout PA‐6 matrix upon increasing the ratio of unSEBS to SEBS‐g‐MAH, until reaching a maximum value. In the case of the (PA‐6)/PC blend compatibilized with a 50/50 combination of unSEBS and SEBS‐g‐MAH, the highest mechanical properties, i.e., tensile strength, impact resistance, and strain at break, were achieved owing to compatibilizing effect of virgin and maleated SEBS constituents. J. VINYL ADDIT. TECHNOL., 21:245–252, 2015. © 2014 Society of Plastics Engineers     

Melt rheology and properties of compatibilized recycled poly(ethylene terephthalate)/(styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer blends

Blends of recycled poly(ethylene terephthalate) (R‐PET) and (styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer (SEEPS) compatibilized with (maleic anhydride)‐grafted‐styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MAH) were prepared by melt blending. The compatibilizing effects of SEBS‐g‐MAH were investigated systematically by study of the morphology, linear viscoelastic behavior, and thermal and mechanical properties of the blends. The results show that there is good agreement between the results obtained by rheological measurement and morphological analysis. The rheological test shows that the melt elasticity and melt strength of the blends increase with the addition of SEBS‐g‐MAH. The Cole‐Cole plots and van Gurp‐Palmen plots confirm the compatibilizing effect of SEBS‐g‐MAH. However, the Palierne model fails to predict the linear viscoelastic properties of the blends. The morphology observation shows that all blends exhibit a droplet‐matrix morphology. In addition, the SEEPS particle size in the (R‐PET)/SEEPS blends is significantly decreased and dispersed uniformly by the addition of SEBS‐g‐MAH. Differential scanning calorimeter analysis shows that the crystallization behavior of R‐PET is restricted by the incorporation of SEEPS, whereas the addition of SEBS‐g‐MAH improves the crystallization behavior of R‐PET compared with that of uncompatibilized (R‐PET)/SEEPS blends. The Charpy impact strength of the blends shows the highest value at SEBS‐g‐MAH content of 10%, which is about 210% higher than that of pure R‐PET. J. VINYL ADDIT. TECHNOL., 22:342–349, 2016. © 2014 Society of Plastics Engineers     

Dynamic mechanical properties in blends of poly(styrene‐b‐isoprene‐b‐styrene) with aromatic hydrocarbon resin

The damping properties in blends of poly(styrene‐b‐isoprene‐b‐styrene) (SIS) and hydrogenated aromatic hydrocarbon (C₉) resin were investigated by dynamic mechanical analysis. SIS exhibited two independent peaks of loss factor (tan δ) corresponding to the glass transition of polyisoprene (PI) and polystyrene (PS) segments, respectively. The addition of hydrogenated C₉ resin had a positive impact on the damping of SIS. With the increasing softening point and content of the resin, the main tan δ peak shifted to higher temperatures and the useful damping temperature range was broadened. Addition of mica or PS was found to widen the effective damping range evidently in the high‐temperature region, especially when PS was mixed in the solid state. It was concluded that the dispersed PS domains played a role of reinforcing fillers at low temperatures and served as a polymer component with a tan δ peak due to its glass transition at the high temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4157–4164, 2006     

Characterization of morphology in chemically modified styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene by solid‐state nuclear magnetic resonance

Multiphase triblock styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene (SEBS) copolymers chemically modified with maleic anhydride (MAH) in the presence of a radical initiator by reactive extrusion were studied by solid‐state ¹H‐NMR and ¹³C‐NMR. In the experiments performed, the concentrations of MAH and initiator were kept constant, whereas the temperature profile in the extruder was varied. Samples with known extents of grafting and crosslinking were analyzed with NMR with techniques based on proton spin diffusion to investigate the microphase structure of the modified copolymers. The ¹³C‐NMR results show that the size of the rigid domains was about 15 nm and was not significantly changed by the modification. Alterations in the rubbery phase were illustrated by measured changes in proton spin‐spin (T₂) relaxation times. The fraction of protons having intermediate mobilities increased slightly in modified SEBS with respect to that observed in unmodified copolymers. These results were found to be independent of the extruder temperature profiles used, at least in the range studied. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of maleated styrene–(ethylene‐co‐butene)–styrene on the morphology and mechanical and thermal properties of polystyrene/polyamide 1212 blends

Polystyrene (PS)/polyamide 1212 (PA 1212) blends were compatibilized with a maleated triblock copolymer of styrene–(ethylene‐co‐butene)–styrene (SEBS‐g‐MA). Scanning electron microscopy revealed that the addition of SEBS‐g‐MA was beneficial to the dispersion of PA 1212 in the PS matrix because of the reaction between them. The variation of the fraction of SEBS‐g‐MA in the blends allowed the manipulation of the phase structure, which first formed a sheetlike structure and then formed a cocontinuous phase containing PA 1212/SEBS‐g‐MA core–shell morphologies. As a result, the mechanical properties, especially the Charpy notched impact resistance, were significantly improved with the addition of SEBS‐g‐MA. Differential scanning calorimetry (DSC) data indicated that the strong interaction between SEBS‐g‐MA and PA 1212 in the blends retarded the crystallization of PA 1212. The heat distortion temperature of the compatibilized blends was improved in comparison with that of the unmodified blend, probably because of the apparent increase in the glass‐transition temperature with an increasing concentration of SEBS‐g‐MA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1354–1360, 2005     

Kinetics of phase separation of poly(styrene‐co‐methyl methacrylate) and poly(styrene‐co‐acrylonitrile) blends

The phase behavior and kinetics of phase separation for blends of the random copolymer poly(styrene‐co‐methyl methacrylate) (SMMA) and poly(styrene‐co‐acrylonitrile) (SAN) were studied by using small‐angle laser light scattering. The partially miscible SMMA/SAN blends undergo spinodal decomposition (SD) and subsequent domain coarsening when quenched inside the unstable region. For blends of SMMA and SAN, the early stages of the phase separation process could be observed, unlike a number of other blends where the earliest stages are not visible by light scattering. The process was described in terms of the Cahn–Hilliard linear theory. Subsequently, a coarsening process was detected and the time evolution of q_m at the beginning of the late stages of phase separation followed the relationship q_m∝t^?1/3, corresponding to an evaporation–condensation mechanism. Self‐similar growth of the phase‐separated structures at different timescales was observed for the late stage. Copyright © 2004 Society of Chemical Industry     

Tensile properties and morphological evolution of polypropylene and poly(ethylene‐co‐1‐octene) blends

Extruded sheet of isotactic polypropylene and poly(ethylene‐co‐1‐octene) blends extruded from a counterrotating twin‐screw extruder were studied by scanning electron microscopy, tensile test, and small‐angle X‐ray scattering. The average characteristic length (Λ_m) determined by the statistical computing from the SEM images increases linearly with increasing of dispersed phase concentration. When POE content is 50 wt% (double continuous phase), Λ_m is two or three times as big as that of other blends ratio. The analyses of SAXS data confirm this result. Comparison has been made between experimental data of tensile test and those predicted from several meso‐mechanical models such as parallel model, series model, Halpin's model, Mori‐Tanaka's model, and modified mixture model. The modified mixture model is an effective method for predicting Young's modulus in comparison with other models. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) and poly(styrene‐co‐acrylonitrile)

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and poly(styrene‐co‐acrylonitrile) (SAN) prepared by solution casting were investigated by differential scanning calorimetry. In the study of PHBV‐SAN blends by differential scanning calorimetry, glass transition temperature and melting point of PHBV in the PHBV‐SAN blends were almost unchanged compared with those of the pure PHBV. This result indicates that the blends of PHBV and SAN are immiscible. However, crystallization temperature of the PHBV in the blends decreased approximately 9–15°. From the results of the Avrami analysis of PHBV in the PHBV‐SAN blends, crystallization rate constant of PHBV in the PHBV‐SAN blends decreased compared with that of the pure PHBV. From the above results, it is suggested that the nucleation of PHBV in the blends is suppressed by the addition of SAN. From the measured crystallization half time and degree of supercooling, interfacial free energy for the formation of heterogeneous nuclei of PHBV in the PHBV‐SAN blends was calculated and found to be 2360 (mN/m)³ for the pure PHBV and 2920–3120 (mN/m)³ for the blends. The values of interfacial free energy indicate that heterogeneity of PHBV in the PHBV‐SAN blends is deactivated by the SAN. This result is consistent with the results of crystallization temperature and crystallization rate constant of PHBV in the PHBV‐SAN blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 673–679, 2000     

Mechanical properties of polystyrene/polyamide 6 blends compatibilized with the ionomer poly(styrene‐co‐sodium acrylate)

The compatibilizing effect of the ionomer, poly(styrene‐co‐sodium acrylate) (PSSAc), on immiscible blends of polystyrene (PS)/polyamide 6 (PA6) was studied by mechanical tests and scanning electron microscopy. The PSSAc acts as an effective compatibilizer because both the deformation at break (%) obtained by tensile stress–strain tests and the impact rupture energy are larger in blends containing small amounts of PSSAc. The morphologies of the fractured surfaces produced by tensile stress–strain tests of blends with or without the ionomer confirm that PSSAc increases the interfacial adhesion between PS and PA6 phases. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2545–2551, 2004     

Thermoplastic elastomeric nanocomposites from poly[styrene–(ethylene‐co‐butylene)–styrene] triblock copolymer and clay: Preparation and characterization

Thermoplastic elastomer (TPE)–clay nanocomposites based on poly[styrene–(ethylene‐co‐butylene)–styrene] triblock copolymer (SEBS) were prepared. Natural sodium montmorillonite (MMT) clay was organically modified by octadecyl amine to produce an amine‐modified hydrophobic nanoclay (OC). Commercially available Cloisite 20A (CL20) and Cloisite 10A, tallow ammine modified nanoclays, were also used. The intergallery spacing of MMT increased on amine modification as suggested by the shifting of the X‐ray diffraction (XRD) peak from 7.6 to 4.5 and 3.8° in the cases of OC and CL20, respectively. The latter demonstrated no XRD peak when it was used at 2 and 4 parts phr in the SEBS system. Transmission electron microscopy studies showed the intercalation–exfoliation morphology in SEBS containing 4 parts of CL20₄–SEBS, agglomeration in SEBS having 4 parts of MMT, and mixed morphology in SEBS with 4 parts of OC systems. Locations of the clay particles were indicated by the atomic force micrographs. Mechanical and dynamic mechanical thermal analysis studies confirmed the best properties with the CL20₄–SEBS nanocomposites. Significant improvements in mechanical properties such as tensile strength, modulus, work to break, and elongation at break were achieved with the CL20₄–SEBS in polymer‐layered silicate nanocomposites. Dynamic mechanical studies further showed the affinity of the organoclays toward both segments of the TPE and a compatibilization effect with CL20 at a 4‐phr loading. Atomic force microscopy showed distinctly different morphologies in nanocomposites prepared through solution and melt processing. Comparisons of the mechanical, dynamic mechanical, and morphological properties of the nanocomposites prepared by melt and solution intercalation processes were done. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2040–2052, 2006     

Polypropylene/silica micro‐ and nanocomposites modified with poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene)

The effects of different silica loadings and elastomeric content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with 5, 10, 15, and 20 vol % of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) SEBS added to total composite volume were investigated. Four silica fillers differing in size (nano‐ vs. micro‐) and in surface properties (untreated vs. treated) were chosen as fillers. Elastomer SEBS was added as impact modifier and compatibilizer at the same time. The morphology of ternary polymer composites revealed by light and scanning electron microscopies was compared with morphology predicted models based on interfacial properties. The results indicated that general morphology of composite systems was determined primarily by interfacial properties, whereas the spherulitic morphology of polypropylene matrix was a result of two competitive effects: nucleation effect of filler and solidification effect of elastomer. Tensile and impact strength properties were mainly influenced by combined competetive effects of stiff filler and tough SEBS elastomer. Spherulitic morphology of polypropylene matrix might affect some mechanical properties additionally. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41486.     

Morphology and mechanical properties of polyamide 12 blends with styrene/ethylene–butylene/styrene rubbers with and without maleation

Blends of polyamide 12 (PA12) with styrene/ethylene–butylene/styrene (SEBS) and maleic anhydride grafted SEBS (SEBS‐g‐MA) were prepared by twin‐screw extrusion and injection molding. The morphology, mechanical properties, and dynamic mechanical properties of the blends were studied. The morphology of the blends was evaluated from the etched surfaces of cryogenically fractured specimens with scanning electron microscopy. The morphological parameters showed that the PA12/SEBS‐g‐MA blends (PM series) exhibited a finer and more uniform rubber dispersion than the PA12/SEBS blends (PS series) because of the interfacial chemical reactions. SEBS functionalization via maleic anhydride grafting strongly affected the morphological parameters, such as the domain size, interfacial area per unit of volume, and critical interparticle distance, but the distribution of the rubber domains in the blends was less affected. Tensile and impact studies showed that the PS blends had worse mechanical properties than the PM blends. The tensile strength and elongation at break of the PM blends were considerably greater than those of the PS blends. The fracture toughness and energy values determined for notched Charpy specimens in high‐speed impact tests were markedly higher for the PM blends than for the PS blends. A similar observation was obtained from instrumented falling weight impact studies. Dynamic mechanical analysis confirmed the incompatibility of the blend components because the glass‐transition temperatures of PA12 and the rubber phase (SEBS and SEBS‐g‐MA) were not affected. © 2005 Wiley Periodicals, Inc. J Appl polym Sci 95: 1376–1387, 2005     

Effects of tetramethylpolycarbonate‐block‐poly(styrene‐co‐acrylonitrile) copolymers containing various amounts of acrylonitrile on the interfacial properties of polycarbonate and poly(styrene‐co‐acrylonitrile) blends

Tetramethylpolycarbonate‐block‐poly(styrene‐co‐acrylonitrile) (TMPC‐block‐SAN) block copolymers containing various amounts of acrylonitrile (AN) were examined as compatibilizers for blends of polycarbonate (PC) with poly(styrene‐co‐acrylonitrile) (SAN) copolymers. To explore the effects of block copolymers on the compatibility of PC/SAN blends, the average diameter of the dispersed particles in the blend was measured with an image analyzer, and the interfacial properties of the blends were analyzed with an imbedded fibre retraction technique and an asymmetric double‐cantilever beam fracture test. Reduction in the average diameter of dispersed particles and effective improvement in the interfacial properties was observed by adding TMPC‐block‐SAN copolymers as compatibilizer of PC/SAN blend. TMPC‐block‐SAN copolymer was effective as a compatibilizer when the difference in the AN content of SAN copolymer and that of SAN block in TMPC‐block‐SAN copolymer was less than about 10 wt%. Copyright © 2004 Society of Chemical Industry     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dynamic mechanical and morphological behavior of blends of polystyrene and poly[acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene] prepared by in situ polymerization of styrene

PS/AES blends were prepared by in situ polymerization of styrene in the presence of AES elastomer, a grafting copolymer of poly(styrene‐co‐acrylonitrile) – SAN and poly(ethylene‐co‐propylene‐co‐diene)–EPDM chains. These blends are immiscible and present complex phase behavior. Selective extraction of the blends' components showed that some fraction of the material is crosslinked and a grafting of PS onto AES is possible. The morphology of the noninjected blends consists of spherical PS domains covered by a thin layer of AES. After injection molding, the blends show morphology of disperse elastomeric phase morphology in a rigid matrix. Two factors could contribute to the change of morphology: (1) the stationary polymerization conditions did not allow the mixture to reach the equilibrium morphology; (2) the grafting degree between PS and AES was not high enough to ensure the morphological stability against changes during processing in the melting state. The drastic change of EPDM morphology from continuous to disperse phase has as consequence a decrease in the intensity of the loss modulus peaks corresponding to the EPDM glass transition. However, the storage modulus at temperatures between the glass transition of EPDM and PS/SAN phases does not change significantly. This effect was attributed to the presence of the SAN rigid chains in the AES. © 2009 Wiley Periodicals, Inc. Journal of Applied Polymer Science, 2009     

Influences of dicumyl peroxide on morphology and mechanical properties of polypropylene/poly(styrene‐b‐butadiene‐b‐styrene) blends via vane‐extruder

Polypropylene (PP) and poly(styrene‐b‐butadiene‐b‐styrene) block copolymer (SBS) were melt‐blended in the presence of initiator system. Dicumyl peroxide (DCP)/Triallyl isocyanurate (TAIC) via self‐deigned VE, aiming at in situ reactive compatibilization of toughed PP/SBS blend. The reactivity, morphology and mechanical properties of PP/SBS/DCP/TAIC blends were studied. Online torque detection was conducted to monitor changes in viscosities of reactive compatibilized blends, which could give proof of the interfacial grafted reaction induced by DCP/TAIC system. The effect of reactive compatibilization on the dispersed particles sizes and interfacial adhesion was studied by scanning electron microscopy. Analysis on mechanical performance revealed the impact strength improved after treated by initiator system, moreover, the impact‐fractured surface observation showed, the failure mode changed from debonding mechanism of neat 50PP/50SBS blend to plastic deformation mechanism of blend containing 3.0 phr initiator system. With improved interfacial adhesion, compatibilized blends not only were toughened but also exhibited enhanced tensile strength and thermal stability. Dynamic mechanical analysis showed a reduction of between PP phase and the PB segments in SBS phase, indicating reactive compatibilization of the blend was achieved. In the final part, a brief discussion was given about the dominant effects from chain scission of PP matrix to intergrafting reactions of PP and SBS, under different content of DCP/TAIC initiator system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41543.     

Morphology and mechanical properties of polypropylene and poly(ethylene‐co‐methyl acrylate) blends

The morphology and mechanical properties of isotactic polypropylene (iPP) and poly(ethylene‐co‐methyl acrylate) (EMA) blends were investigated. Various EMA copolymers with different methyl acrylate (MA) comonomer content were used. iPP and EMA formed immiscible blends over the composition range studied. The crystallization and melting reflected that of the individual components and the crystallinity was not greatly affected. The size of the iPP crystals was larger in the blends than those of pure iPP, indicating that EMA may have reduced the nucleation density of the iPP; however, the growth rate of the iPP crystals was found to remain constant. The tensile elongation at break was greatly increased by the presence of EMA, although the modulus remained approximately constant until the EMA composition was greater than 20%. EMA with a 9.0% MA content provided the optimum effect on the mechanical properties of the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 175–185, 2003