3D‐Printed,All‐in‐One Evaporator for High‐Efficiency Solar Steam Generation under 1 Sun Illumination

Using solar energy to generate steam is a clean and sustainable approach to addressing the issue of water shortage. The current challenge for solar steam generation is to develop easy‐to‐manufacture and scalable methods which can convert solar irradiation into exploitable thermal energy with high efficiency. Although various material and structure designs have been reported, high efficiency in solar steam generation usually can be achieved only at concentrated solar illumination. For the first time, 3D printing to construct an all‐in‐one evaporator with a concave structure for high‐efficiency solar steam generation under 1 sun illumination is used. The solar‐steam‐generation device has a high porosity (97.3%) and efficient broadband solar absorption (>97%). The 3D‐printed porous evaporator with intrinsic low thermal conductivity enables heat localization and effectively alleviates thermal dissipation to the bulk water. As a result, the 3D‐printed evaporator has a high solar steam efficiency of 85.6% under 1 sun illumination (1 kW m^?2), which is among the best compared with other reported evaporators. The all‐in‐one structure design using the advanced 3D printing fabrication technique offers a new approach to solar energy harvesting for high‐efficiency steam generation.     

High‐Efficiency Single‐Component Organic Light‐Emitting Transistors

Construction of high‐performance organic light‐emitting transistors (OLETs) remains challenging due to the limited desired organic semiconductor materials. Here, two superior high mobility emissive organic semiconductors, 2,6‐diphenylanthracene (DPA) and 2,6‐di(2‐naphthyl) anthracene (dNaAnt), are introduced into the construction of OLETs. By optimizing the device geometry for balanced ambipolar efficient charge transport and using high‐quality DPA and dNaAnt single crystals as active layers, high‐efficiency single‐component OLETs are successfully fabricated, with the demonstration of strong and spatially controlled light emission within both p‐ and n‐ conducting channels and output of high external quantum efficiency (EQE). The obtained EQE values in current devices are approaching 1.61% for DPA‐OLETs and 1.75% for dNaAnt‐based OLETs, respectively, which are the highest EQE values for single‐component OLETs in the common device configuration reported so far. Moreover, high brightnesses of 1210 and 3180 cd m^?2 with current densities up to 1.3 and 8.4 kA cm^?2 are also achieved for DPA‐ and dNaAnt‐based OLETs, respectively. These results demonstrate the great potential applications of high mobility emissive organic semiconductors for next‐generation rapid development of high‐performance single‐component OLETs and their related organic integrated electro‐optical devices.     

High‐Efficiency Nonfullerene Organic Solar Cells with a Parallel Tandem Configuration

In this work, a highly efficient parallel connected tandem solar cell utilizing a nonfullerene acceptor is demonstrated. Guided by optical simulation, each of the active layer thicknesses of subcells are tuned to maximize its light trapping without spending intense effort to match photocurrent. Interestingly, a strong optical microcavity with dual oscillation centers is formed in a back subcell, which further enhances light absorption. The parallel tandem device shows an improved photon‐to‐electron response over the range between 450 and 800 nm, and a high short‐circuit current density (J _SC) of 17.92 mA cm^?2. In addition, the subcells show high fill factors due to reduced recombination loss under diluted light intensity. These merits enable an overall power conversion efficiency (PCE) of >10% for this tandem cell, which represents a ≈15% enhancement compared to the optimal single‐junction device. Further application of the designed parallel tandem configuration to more efficient single‐junction cells enable a PCE of >11%, which is the highest efficiency among all parallel connected organic solar cells (OSCs). This work stresses the importance of employing a parallel tandem configuration for achieving efficient light harvesting in nonfullerene‐based OSCs. It provides a useful strategy for exploring the ultimate performance of organic solar cells.     

Sandwich Photothermal Membrane with Confined Hierarchical Carbon Cells Enabling High‐Efficiency Solar Steam Generation

Solar‐driven vaporization is a sustainable solution to water and energy scarcity. However, most of the present evaporators are still suffering from inefficient utilization of converted thermal energy. Herein, a universal sandwich membrane strategy is demonstrated by confining the hierarchical porous carbon cells in two energy barriers to obtain a high‐efficiency evaporator with a rapid water evaporation rate of 1.87 kg m^?2 h^?1 under 1 sun illumination, which is among the highest performance for carbon‐based and wood‐based evaporators. The significantly enhanced evaporation rate is mainly attributed to the inherently optimized porous evaporation mode derived from the hierarchical hollow structures of pollen carbon cells, and the synergistically regulated water transporting and thermal management performance of the sandwich membrane. Moreover, the constructed sandwich membrane also exhibits excellent self‐regenerating performance in simulated seawater and high salinity water. The developed device can maintain an average evaporation rate of 4.3 L m^?2 day^?1 in a 25 day consecutive outdoor test.     

Wood‐Inspired High‐Performance Ultrathick Bulk Battery Electrodes

Ultrathick electrode design is a promising strategy to enhance the specific energy of Li‐ion batteries (LIBs) without changing the underlying materials chemistry. However, the low Li‐ion conductivity caused by ultralong Li‐ion transport pathway in traditional random microstructured electrode heavily deteriorates the rate performance of ultrathick electrodes. Herein, inspired by the vertical microchannels in natural wood as the highway for water transport, the microstructures of wood are successfully duplicated into ultrathick bulk LiCoO₂ (LCO) cathode via a sol–gel process to achieve the high areal capacity and excellent rate capability. The X‐ray‐based microtomography demonstrates that the uniform microchannels are built up throughout the whole wood‐templated LCO cathode bringing in 1.5 times lower of tortuosity and ≈2 times higher of Li‐ion conductivity compared to that of random structured LCO cathode. The fabricated wood‐inspired LCO cathode delivers high areal capacity up to 22.7 mAh cm^?2 (five times of the existing electrode) and achieves the dynamic stress test at such high areal capacity for the first time. The reported wood‐inspired design will open a new avenue to adopt natural hierarchical structures to improve the performance of LIBs.     

Highly Flexible and Efficient Solar Steam Generation Device

Solar steam generation with subsequent steam recondensation has been regarded as one of the most promising techniques to utilize the abundant solar energy and sea water or other unpurified water through water purification, desalination, and distillation. Although tremendous efforts have been dedicated to developing high‐efficiency solar steam generation devices, challenges remain in terms of the relatively low efficiency, complicated fabrications, high cost, and inability to scale up. Here, inspired by the water transpiration behavior of trees, the use of carbon nanotube (CNT)‐modified flexible wood membrane (F‐Wood/CNTs) is demonstrated as a flexible, portable, recyclable, and efficient solar steam generation device for low‐cost and scalable solar steam generation applications. Benefitting from the unique structural merits of the F‐Wood/CNTs membrane—a black CNT‐coated hair‐like surface with excellent light absorbability, wood matrix with low thermal conductivity, hierarchical micro‐ and nanochannels for water pumping and escaping, solar steam generation device based on the F‐Wood/CNTs membrane demonstrates a high efficiency of 81% at 10 kW cm^?2, representing one of the highest values ever‐reported. The nature‐inspired design concept in this study is straightforward and easily scalable, representing one of the most promising solutions for renewable and portable solar energy generation and other related phase‐change applications.     

A Controlled Design of Ripple‐Like Polyamide‐6 Nanofiber/Nets Membrane for High‐Efficiency Air Filter

The filtration capacity of fibrous media for airborne particles is restricted by their thick diameter, low porosity, and limited frontal area. The ability to solve this problem would have broad technological implications for various air filtration applications; despite many past efforts, it remains a great challenge to achieve. Herein, a facile and scalable strategy to fabricate the ripple‐like polyamide‐6 nanofiber/nets (PA‐6 NF/N) air filter via combining electrospinning/netting technique with receiving substrate design is demonstrated. This proposed approach allows the scaffold filaments to orderly embed into 2D PA‐6 nanonets layer with Steiner‐tree structures and nanoscale diameter of ≈20 nm, resulting in the ripple‐like membrane with extremely small pore size, highly porous structure, and hugely extended frontal surface, by facilely adjusting its pleat span and pleat pitch. These unique structural advantages enable the ripple‐like PA‐6 NF/N filter to filtrate the ultrafine particles with high removal efficiency of 99.996%, low air resistance of 95 Pa, and robust quality factor of >0.11 Pa^?1; using its superlight weight of 0.9 g m^?2 and physical sieving manner. This approach has the potentialities to give rise to a novel generation of filter media displaying enhanced filtration capacity for various applications thanks to their nanoscale features and designed macrostructures.     

High‐Efficiency Red Organic Light‐Emitting Diodes with External Quantum Efficiency Close to 30% Based on a Novel Thermally Activated Delayed Fluorescence Emitter

Researchers have spared no effort to design new thermally activated delayed fluorescence (TADF) emitters for high‐efficiency organic light‐emitting diodes (OLEDs). However, efficient long‐wavelength TADF emitters are rarely reported. Herein, a red TADF emitter, TPA–PZCN, is reported, which possesses a high photoluminescence quantum yield (Φ_PL) of 97% and a small singlet–triplet splitting (ΔE_ST) of 0.13 eV. Based on the superior properties of TPA–PZCN, red, deep‐red, and near‐infrared (NIR) OLEDs are fabricated by utilizing different device structure strategies. The red devices obtain a remarkable maximum external quantum efficiency (EQE) of 27.4% and an electroluminescence (EL) peak at 628 nm with Commission Internationale de L'Eclairage (CIE) coordinates of (0.65, 0.35), which represents the best result with a peak wavelength longer than 600 nm among those of the reported red TADF devices. Furthermore, an exciplex‐forming cohost strategy is adopted. The devices achieve a record EQE of 28.1% and a deep‐red EL peak at 648 nm with the CIE coordinates of (0.66, 0.34). Last, nondoped devices exhibit 5.3% EQE and an NIR EL peak at 680 nm with the CIE coordinates of (0.69, 0.30).     

A Shape‐Adaptive Thin‐Film‐Based Approach for 50% High‐Efficiency Energy Generation Through Micro‐Grating Sliding Electrification

Effectively harvesting ambient mechanical energy is the key for realizing self‐powered and autonomous electronics, which addresses limitations of batteries and thus has tremendous applications in sensor networks, wireless devices, and wearable/implantable electronics, etc. Here, a thin‐film‐based micro‐grating triboelectric nanogenerator (MG‐TENG) is developed for high‐efficiency power generation through conversion of mechanical energy. The shape‐adaptive MG‐TENG relies on sliding electrification between complementary micro‐sized arrays of linear grating, which offers a unique and straightforward solution in harnessing energy from relative sliding motion between surfaces. Operating at a sliding velocity of 10 m/s, a MG‐TENG of 60 cm² in overall area, 0.2 cm³ in volume and 0.6 g in weight can deliver an average output power of 3 W (power density of 50 mW cm^?2 and 15 W cm^?3) at an overall conversion efficiency of ～50%, making it a sufficient power supply to regular electronics, such as light bulbs. The scalable and cost‐effective MG‐TENG is practically applicable in not only harvesting various mechanical motions but also possibly power generation at a large scale.     

Roll‐to‐Roll Cohesive,Coated, Flexible,High‐Efficiency Polymer Light‐Emitting Diodes Utilizing ITO‐Free Polymer Anodes

This paper reports solution‐processed, high‐efficiency polymer light‐emitting diodes fabricated by a new type of roll‐to‐roll coating method under ambient air conditions. A noble roll‐to‐roll cohesive coating system utilizes only natural gravity and the surface tension of the solution to flow out from the capillary to the surface of the substrate. Because this mechanism uses a minimally cohesive solution, the roll‐to‐roll cohesive coating can effectively realize an ultra‐thin film thickness for the electron injection layer. In addition, the roll‐to‐roll cohesive coating enables the fabrication of a thicker polymer anode film more than 250 nm at one time by modification of the surface energy and without wasting the solution. It is observed that the standard sheet resistance deviation of the polymer anode is only 2.32 Ω/□ over 50 000 bending cycles. The standard sheet resistance deviation of the polymer anode in the different bending angles (0 to 180°) is 0.313 Ω/□, but the case of the ITO‐PET is 104.93 Ω/□. The average surface roughness of the polymer anode measured by atomic force microscopy is only 1.06 nm. Because the surface of the polymer anode has a better quality, the leakage current of the polymer light‐emitting diodes (PLEDs) using the polymer anode is much lower than that using the ITO‐PET substrate. The luminous power efficiency of the two devices is 4.13 lm/W for the polymer anode and 3.21 lm/W for the ITO‐PET. Consequently, the PLEDs made by using the polymer anode exhibited 28% enhanced performance because the polymer anode represents not only a higher transparency than the ITO‐PET in the wavelength of 560 nm but also greatly reduced roughness. The optimized the maximum current efficiency and power efficiency of the device show around 6.1 cd/A and 5.1 lm/W, respectively, which is comparable to the case of using the ITO‐glass.     

Super Moisture‐Absorbent Gels for All‐Weather Atmospheric Water Harvesting

Atmospheric water harvesting (AWH)—producing fresh water via collecting moisture from air—enables sustainable water delivery without geographical and hydrologic limitations. However, the fundamental design principle to prepare materials that can convert the water vapor in the air to collectible liquid water is still mostly unknown. Here, a super moisture‐absorbent gel, which is composed of hygroscopic polypyrrole chloride penetrating in hydrophilicity‐switchable polymeric network of poly N‐isopropylacrylamide, is shown. Based on such design, a high‐efficiency water production by AWH has been achieved in a broad range of relative humidity. The synergistic effect enabled by the molecular level integration of hygroscopic and hydrophilicity‐switchable polymers in a network architecture presents controllable interaction between the gel and water molecules, simultaneously realizing efficient vapor capturing, in situ water liquefaction, high‐density water storage and fast water releasing under different weather conditions. Being an effective method to regulate migration of water molecules, such design represents a novel strategy to improve the AWH, and it is also fundamental to other water management systems for environmental cooling, surficial moisturizing and beyond.