p型掺杂GaAs液相外延材料的光致发光研究

对Si掺杂和Zn掺杂p型GaAs液相外延材料进行光致发光研究。用发射波长为510.6nm和578.2nm的溴化亚铜激光器为激发光源,样品的低温由氦循环致冷机提供,样品室温度在10～300K中可调。在所选取的狭缝宽度下谱仪的分辨率大致为2nm,所提供的数据全部经过系统灵敏度校正并进行分峰拟合。对Si掺杂p型GaAs样品PL谱中一些主要特征进行讨论,认为A_1,A_2,A_3三个发射带分别对应着导带“尾”态中电子向价带和两个浅受主能级的跃迁,它们随温度变化的情况,和带隙宽度及电子填充状态随温度变化有关。此外,我们还观察了掺Zn的p型GaAs样品的PL谱,与掺Si样品比较,具有明显不同的特征,谱线在长波端(～950nm)的上扬趋势表明在低能区域可能存在一个与深能级复合有关的宽发射带。     

掺杂GaAs／AlGaAs超晶格的激发态向受主中心跃迁的发光

在室温下测量了GaAs／Al0.28Ga0.72As超晶格的光致发光，发现在波长λ=764nm处存在一较强的发光峰。理论分析表明，此峰是量子阱阱口附近能级上的电子与受主杂质上的空穴复合发光。实验还观测到在λ=824nm和829nm处分别存在一发光峰。分析表明，λ=829nm和λ=824mn处的发光峰分别为激子发光和量子阱中基态电子与基态重空穴的复合发光；理论计算值与实验结果符合得很好。     

GaInNAs/GaAs量子阱的光致发光谱和光调制反射谱

研究了GaInNAs/GaAs多量子阱在不同温度和激发功率下的光致发光(PL)谱以及光调制反射(PR)谱.发现PL谱主发光峰的能量位置随温度的变化不满足Varshni关系,而是呈现出反常的S型温度依赖关系.进一步测量,特别是在较低的激发光功率密度下,发现有两个不同来源的发光峰,它们分别对应于氮引起的杂质束缚态和带间的激子复合发光.随温度变化,这两个发光峰相对强度发生变化,造成主峰(最强的峰)的位置发生切换,从而导致表观上的S型温度依赖关系.采用一个基于载流子热激发和出空过程的模型来解释氮杂质团簇引起的束缚态发光峰的温度依赖关系.     

GaInNAs/GaAs量子阱的光致发光谱和光调制反射谱

研究了GaInNAs/GaAs多量子阱在不同温度和激发功率下的光致发光(PL)谱以及光调制反射(PR)谱.发现PL谱主发光峰的能量位置随温度的变化不满足Varshni关系,而是呈现出反常的S型温度依赖关系.进一步测量,特别是在较低的激发光功率密度下,发现有两个不同来源的发光峰,它们分别对应于氮引起的杂质束缚态和带间的激子复合发光.随温度变化,这两个发光峰相对强度发生变化,造成主峰(最强的峰)的位置发生切换,从而导致表观上的S型温度依赖关系.采用一个基于载流子热激发和出空过程的模型来解释氮杂质团簇引起的束缚态发光峰的温度依赖关系.     

GaAs/AlGaAs多量子阱结构的光吸收谱和横向光电流谱

研究了MBE GaAs/AlGaAs多量子阱结构的横向光电流谱和光吸收谱。在光电流谱中观测到多种允许和禁戒的激子吸收峰以及一个阱中受主态至n=1电子态的非本征吸收峰。确定出5个空穴子带至2个电子子带的跃迁以及这些子带的间距。采用简单带方势阱模型并取参数Q_c=0.6,m_c=0.0665,m_h=0.45和m_l=0.12的计算结果与实验数据符合得相当好。将光吸收谱与光荧光谱进行了比较。     

H_2O在Si(100)-(2×1)表面上的吸附和氧化

利用AES以及HeI(21.2eV)和同步辐射(138.5eV)光电子谱研究了H_2O在Si(100)-(2 ×1)表面上的室温吸附、高温退火效应以及开始氧化的过程.AES的测量结果表明,H_2O在这种表面上的粘附系数很大,在350K下,当曝汽量约为2L时就达到饱和,其覆盖率θ=1/2.价带区域的光电子谱出现三个由于H_2O吸附而引起的特征峰,低于价带顶分别为6.2、7.2和11.5eV.350K下的 H_2O吸附导致Si 2p能级的结合能增加0.8±0.1eV,相当于一个Si原子同一个氧原子键合的情况.在 640K下退火后,出现Si 2p的第二个化学位移峰,其位置比体内Si 2p 峰约低 1.8eV,表明这时的 H_2O已经完全离解,一部分Si原子同两个氧原子键合(可能是桥键方式). 在 870K下退火,得到Si 2p的四个化学位移峰,说明氧已经贯穿进Si的体内,形成SiO_x(x=1、2、3和4).当退火温度进一步提高到T(?)970K时,恢复Si的清洁表面,表明氧被完全脱附.     

氮化镓注镁(Mg:GaN)的光致发光

利用低压MOCVD在蓝宝石衬底上外延生长了GaN,用离子注入法掺入Mg杂质,退火后,进行光致发光测量,观察到显著的蓝光发射和黄带发射.光谱分析给出了与注入Mg离子相关的GaN禁带中能级的精细结构,其中: 间位Mg(Mgi)能级(导带下170meV)到替位Mg(MgGa)受主能级(价带上250meV)的跃迁产生了415nm发光峰; 该能级到价带上390meV能级的跃迁,以及带有紧邻N空位的替位Mg(MgGaVN)能级(导带下310meV)到 MgGa受主能级的跃迁,均产生了438nm发光峰.另外,退火使GaN晶格结构部分恢复,再现了黄带发射.     

氮化镓注镁(Mg:GaN)的光致发光

利用低压MOCVD在蓝宝石衬底上外延生长了GaN,用离子注入法掺入Mg杂质,退火后,进行光致发光测量,观察到显著的蓝光发射和黄带发射.光谱分析给出了与注入Mg离子相关的GaN禁带中能级的精细结构,其中: 间位Mg(Mgi)能级(导带下170meV)到替位Mg(MgGa)受主能级(价带上250meV)的跃迁产生了415nm发光峰; 该能级到价带上390meV能级的跃迁,以及带有紧邻N空位的替位Mg(MgGaVN)能级(导带下310meV)到 MgGa受主能级的跃迁,均产生了438nm发光峰.另外,退火使GaN晶格结构部分恢复,再现了黄带发射.     

弛豫SiGe衬底上SiGe/Si Ⅱ型量子阱

采用 UHV / CVD系统 ,在 Si衬底上生长了具有渐变 Si1 - x Gex 缓冲层结构的弛豫 Si0 .76 Ge0 .2 4虚衬底和 5个周期的 Si0 .76 Ge0 .2 4/ Si多量子阱 .在渐变 Si1 - x Gex 缓冲层生长过程中引入原位退火 ,消除了残余应力 ,抑制了后续生长的 Si Ge中的位错成核 .透射电子显微照片显示 ,位错被有效地限制在组份渐变缓冲层内 ,而 Si Ge上层和 Si Ge/Si量子阱是无位错的 .在样品的 PL 谱中 ,观察到跃迁能量为 0 .96 1e V的 型量子阱的无声子参与 (NP)发光峰 .由于 型量子阱中电子和空穴不在空间同一位置 ,较高光功率激发下引起的高浓度载流子导致能带弯曲严重 .NP峰随激发功率增加向高能方向移动 ,在一定激发条件下 ,电子跃迁或隧穿至弛豫 Si Ge层弯曲的导带底后与处于同一位置的空穴复合发光 ,所以 NP峰积分强度随光激发功率先增加后减小     

AlGaN/AlN/GaN HEMT结构2DEG的光致发光谱

AlGaN/GaN HEMT结构材料主要用于研制微电子器件,对其发光性质的研究相对较少。通过对AlGaN/GaN HEMT结构材料的光致发光谱(PL)研究,观测到了AlGaN势垒层中Al组分为40%的AlGaN/AlN/GaN结构中二维电子气(2DEG)光致发光及其能级分裂现象。在4.5 K低温下,其2DEG发光峰在GaN带边峰能量以下30和40 meV处分裂成两个峰位,直至温度持续升高至40 K后消失。根据GaN价带顶部在单轴晶格场和自旋-轨道耦合共同作用下的能级分裂理论,因自旋-轨道耦合引起的2DEG发光峰两个分裂能级差约为10 meV,与实验测得的结果一致,因此实验观测到的2DEG发光峰的分裂现象是由于氮化镓价带能级的自旋-轨道耦合而形成的。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks