Synergy between tribo-oxidation and strain rate response on governing the dry sliding wear behavior of titanium

The present work provides an insight into the dry sliding wear behavior of titanium based on synergy between tribo-oxidation and strain rate response. Pin-on-disc tribometer was used to characterize the friction and wear behavior of titanium pin in sliding contact with polycrystalline alumina disk under ambient and vacuum condition. The sliding speed was varied from 0.01 to 1.4 ms^?1, normal load was varied from 15.3 to 76 N and with a sliding distance of 1500 m. It was seen that dry sliding wear behavior of titanium was governed by combination of tribo-oxidation and strain rate response in near surface region of titanium. Strain rate response of titanium was recorded by conducting uni-axial compression tests at constant true strain rate of 100 s^?1 in the temperature range from 298 to 873 K. Coefficient of friction and wear rate were reduced with increased sliding speed from 0.01 to 1.0 ms^?1. This is attributed to the formation of in situ self lubricating oxide film (TiO) and reduction in the intensity of adiabatic shear band cracking in the near surface region. This trend was confirmed by performing series of dry sliding tests under vacuum condition of 2 × 10^?4 Torr. Characterization tools such as optical microscopy, scanning electron microscopy, and X-ray diffractometer provided evidence of such processes. These experimental findings can be applied to enhance the dry sliding wear behavior of titanium with proper choice of operating conditions such as sliding speed, normal load, and environment.     

Friction and dry sliding wear behaviour of cermets

The friction and wear behaviour of cermets/steel rubbing pairs were investigated. Friction and wear tests were carried out using three different crèmets on the base of tungsten, titanium and chromium carbides under dry sliding conditions against steel disk (0.45% C). Sliding wear tests were carried out using modified block-on-ring equipment at a sliding speed of 2.2 m/s and normal load 40 N.It is shown that wear resistance and coefficient of friction depend on the type and chemical composition of the cermets. The WC–Co cermets have the highest wear resistance. The wear rate of WC–Co and TiC–NiMo cermets increased with increasing binder content in the cermets. The wear of Cr₃C₂–Ni cermets is more complicated and depends on the composition of cermets. The wear of WC–Co cermets is caused mainly by preferential removal of the cobalt binder, followed by fracture of the intergranular boundaries and fragmentation of the carbide grains. The main wear mechanism in the TiC–NiMo cermets is polishing (micro-abrasion) and adhesion, resulting in a low wear rate. The main wear mechanism of Cr₃C₂–Ni cermets involves thermal cracking and fatigue-related crushing of large carbide grains and carbide framework and also adhesion.     

Wear characteristics of a diffusion bonded sintered steel with short term surface treatments

A pin on disc machine was used to investigate the tribological behavior of a diffusion bonded sintered steel, with and without surface treatments of steam oxidation and manganese phosphating, over a wide range of speed (0.2–4 m/s) and applied load (4–500 N) in conditions of dry sliding and starved lubrication by oil impregnation of the porous structure of the materials. Besides the calculated wear rates, the wear mechanisms were determined by examination of the components of the rubbing system (sintered pin, disc and generated debris). A transition from a mild to a severe wear regime was identified, denoted by sharp changes of the wear rate. A transient wear regime, interposed between the mild and severe wear regimes, was detected. The rubbing surface quality degradation was in terms of material displacement around the pin circumference due to a delamination wear mechanism. Such regime was detected for the base sintered steel in dry sliding at 1 m/s for the load range 60–80 N and for both surface treatments in oil impregnated sliding at 0.5 m/s for the load range 200–300 N. Oil impregnation of the base sintered steel expanded the mild wear regime towards higher loads throughout the whole sliding speed range compared to dry sliding. For the lower speeds of 0.2 and 0.5 m/s, manganese phosphated samples in dry sliding exhibited higher transition loads compared to the base sintered steel. The lower oil impregnability of the surface treated samples, due to the sealing of porosity by steam oxidation, led to slightly lower transition loads in oil impregnated sliding, compared to the base sintered steel.     

Effect of soft carbon black on tribology of deproteinised and polyisoprene rubbers

In this work, the tribological properties of deproteinised natural rubber (DPNR) were examined and compared with synthetic cis-1,4-polyisoprene rubber (IR), namely Natsyn 2200. The effect of adding carbon black (CB) (0, 25 and 50 phr) to both DPNR and IR on the friction and wear characteristics was investigated. Dry abrasion tests were carried out using pin-on-cylinder tribometer with abrasive paper (Diamond 50) under different operating test conditions such as applied normal load (5–35 N), sliding speed (0.3–1.5 m/s) and sliding distance (90–450 m).Experimental results showed that the addition of CB has significantly affected the wear and friction characteristics of both DPNR and IR, i.e. it reduces the abrasion weight loss by more than 70% compared to unfilled rubber, depending on the test conditions and the concentration of CB. The friction coefficient of DPNR was decreased by about 12.5% upon the addition of 50 phr CB, compared to unfilled DPNR. Meanwhile, adding (25–50 phr) CB to IR drastically deteriorates the friction coefficient, i.e. an increase in the friction by about 200% at 25 phr CB and 300% at 50 phr CB compared to unfilled IR.Finally, scanning electron microscopy (SEM) technique is employed to observe the abrasion pattern of rubber in order to correlate the experimental test results to the wear mechanisms.     

Evolution of wear,roughness, and friction of Alloy 600 superalloy surfaces in water-submersed sliding

Self-mated wear and friction of Alloy 600 superalloy was studied in a water-submersed ring-on-rod configuration, loading the side of a 6.35 mm diameter rod across the flat surface of a rotating annular ring of 100 mm outer diameter and 70 mm inner diameter producing two sliding contacts along the ring. Tests were conducted at sliding speeds of 0.178 and 0.330 m/s for sliding distances of 100 m. Normal loads of 51 and 204 N were applied, and initial R_a surface roughnesses of the rings along the sliding direction were either smooth (～0.2 μm) or rough (～7.5 μm). Increased initial ring roughness caused a ～20-fold increase in rod wear at the lighter load, whereas at the heavier load increased initial roughness only caused a ～4-fold increase in wear. At lower initial ring roughness the 4-fold decrease in normal load caused a large (one order-of-magnitude) decrease in rod wear, whereas for rings of higher initial roughness the 4-fold decrease in normal load caused only minor (2-fold or less) decreases in rod wear. Wear during this 100 m sliding distance only experienced a minor effect from the 1.8-fold change in sliding speed, as did friction. In all cases friction coefficient rapidly settled into the range 0.6–0.7, except in the cases of lower load on rings of lower initial roughness where friction coefficient remained above 1 for most of this sliding duration. At this lower load the initial ～0.2 μm rod roughnesses increased to nearly 0.8 μm by the 100 m sliding distance, whereas at the higher load this same sliding distance resulted in roughnesses returning near to the initial 0.2 μm. It was hypothesized more highly loaded cases also went through initial roughening prior to smoothening back to 0.2 μm roughness within the 100 m sliding distance, and given additional sliding the more lightly loaded cases would also experience subsequent smoothening. Increasing sliding distance to 400 m, roughnesses indicated a smoothening back to 0.2 μm level during those lightly loaded tests, with friction coefficient correspondingly dropping from 1 into the 0.6–0.7 range observed in all other cases. Extended sliding to 400 m at light loading against rings of lower initial roughness also allowed a rod wear rate which increased with increased sliding distance to be observed, approaching the same rate observed against initially rough rings within the 100 m sliding distance.     

Effect of electrical current on tribological behavior of copper-impregnated metallized carbon against a Cu–Cr–Zr alloy

A block-on-slip ring-type wear tester was used to investigate the tribological behavior of copper-impregnated metallized carbon against a Cu–Cr–Zr alloy under 2 to 6 N applied load and 0 to 20 A electrical current. The sliding speed was maintained at 25 km/h. The wear loss of copper-impregnated metallized carbon increased with greater electrical current. Under a certain applied load, the wear loss with electrical current was minimized. The tribo-layer had an apparent effect on the friction coefficient. The wear mechanisms were complex, consisting of adhesive wear, abrasive wear and arc erosion.     

Effect of three nitriding treatments on tribological performance of 42CrAlMo7 steel in boundary lubrication

Evolution of friction and wear of 42CrAlMo7 steels with different nitriding processes was investigated during boundary-lubricated rolling–sliding tests. The wear behaviour of nitrided steel with a thin compound layer (produced by plasma nitriding and by gas nitriding followed by oxidation) was characterised by the early removal of the compound layer, and the wear resistance was thus, given by the underlying diffusion layer. In the case of the material with a thick compound layer (produced by gas nitriding) wear was restricted to the compound layer. In this material, at low applied load (300 N, i.e. 485 MPa of Hertzian pressure, in this work), after the removal of the external porous layer wear tended to be negligible. At high applied load (1000 N, 890 MPa), on the other hand, the wear rate became higher than that of the diffusion layer. The friction behaviour was followed by determining the λ-factor evolution during each test. For a given λ-factor, the friction coefficients at 300 N were lower than at 1000 N.     

Friction and wear of aluminium–steel contacts lubricated with ordered fluids-neutral and ionic liquid crystals as oil additives

Friction and wear of ASTM B211 aluminium–AISI 52100 steel contacts have been determined using pin-on-disk tests under variable conditions of normal applied load, sliding speed and temperature, in the presence of a lubricating base oil modified with a 1 wt.% proportion of three different liquid crystalline additives.The tribological behavior of the ionic liquid crystal n-dodecylammonium chloride (LC3) has been compared with that of two neutral liquid crystals: a non-polar species, 4,4′-dibutylazobenzene (LC1) which had previously shown its ability to lower friction and wear of metallic pairs as compared to the base oil, and a cholesterol derivative, cholesteryl linoleate (LC2).At low temperature and low sliding speed values, the friction coefficients obtained for LC1 are lower than those of LC3. As the severity of the contact conditions increases, this tendency reverses and the ionic species LC2 gives rise to lower friction values than LC1.Wear volume losses under increasing normal loads, between 2.45 and 5.89 N, are always lower in the presence of the ionic additive LC3.Lubrication and wear mechanisms are discussed from optical microscopy and SEM observation of the wear scars and wear debris morphology.     

Synthesis of boride coatings on steel using plasma transferred arc (PTA) process and its wear performance

Boriding of the surface of a tool steel using boron powder and the plasma transferred arc process was investigated. It was shown that this method is an easy and effective technique in producing uniform alloyed layers with a thickness of about 1.5 mm and a hardness between 1000 and 1300 HV.The microstructure of the borided surfaces consists of primary Fe₂B-type borides and a eutectic mixture of borides and martensite. Some cracks are observed in the eutectic regions but they do not seem to critically affect the behaviour of the coatings in sliding wear.The wear rate of pin on disc tests is primarily affected by the applied load and it lies between 10⁻⁵ mm³/m for low loads and 10⁻² mm³/m for high loads. Two distinct regimes of mild and severe wear are obtained separated by a critical load. Mild wear is due to the load supporting effect of borides and severe wear is due to their breakage above a critical load. The wear rate is not significantly affected by the sliding velocity and is consistent with the friction coefficient.The friction coefficient varies from 0.13 to 0.23 and depends strongly on the oxidation status of the wear track. The sliding velocity affects the sliding distance where the coefficient of friction reaches equilibrium.     

Role of contact frequency on the wear rate of steel in discontinuous sliding contact conditions

This work presents a novel approach of sliding ball-on-disk wear tests where the disc material is investigated. Each part of the wear track on the disc is in discontinuous contact with the counterbody. The contact frequency at each part of the wear track on the disc with the counterbody is defined by the rotation frequency of the disc. The sliding speed is however a function of both the rotation frequency and wear track diameter. In this work, the effect of the contact frequency on friction and wear was investigated on carbon steel in discontinuous sliding contact with corundum balls. Various sliding speeds were used while maintaining the contact frequency at a fixed value, and various contact frequencies were applied at constant sliding speeds.The wear rate of the disk material is shown to depend not only on the usual wear test parameters, namely sliding speed and contact load, but also on contact frequency. Moreover, contact frequency is shown to be a key factor determining the wear mode even at constant sliding speed and load. At contact frequencies above 9 Hz, the dominant wear mechanism is oxidational wear, while at frequencies below 4 Hz the dominant wear mechanism is adhesive wear. This transition from adhesive to oxidational wear takes place together with a change in the type of debris generated and in the value of the coefficient of friction.The validity of the Garcia-Ramil-Celis model proposed earlier for discontinous sliding contact conditions, is demonstrated for the case of carbon steel disks sliding against a chemically inert counterbody.     

Preparation,microstructure and tribological behavior of laser cladding NiAl intermetallic compound coatings

Nickel aluminide (NiAl) intermetallic compound coatings were in situ synthesized from pre-placed mixed powders of Ni and Al by laser cladding. The phase composition and microstructure of the NiAl coatings were studied by means of X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The effects of laser cladding parameters on the microstructure and friction and wear behavior of the NiAl coatings were investigated. It has been found that laser power density had a crucial influence on the microstructure and friction and wear behavior of NiAl coatings. Namely, the NiAl coatings synthesized under a lower power density have more dense and fine microstructure, and lower friction coefficient and wear rate. Besides, the friction and wear behavior of the laser cladding NiAl coatings is highly dependent on applied normal load and sliding speed; and the resulting coatings sliding against Si₃N₄ in a ball-on-disc contact mode is more suitable for tribological application at a moderate normal load of 3–7 N and sliding speed of 0.16–0.21 m/s.     

Tribocorrosion behaviour of Ni–SiC nano-structured composite coatings obtained by electrodeposition

The combined corrosion-wear degradation of nano-structured Ni–SiC coatings in sliding contacts immersed in electrically conductive solutions is investigated in situ by electrochemical techniques (open-circuit potential measurements, E_OC, the potentiodynamic polarization measurements, PD, and the electrochemical impedance spectroscopy). The coating thickness was 50 μm, with an average volume of dispersed phases inside nickel of 20%. The samples were tested in a cell, containing the electrolyte and electrodes, and mounted on a pin-on-disk tribometer, with the working surface of the specimen facing upwards. Both continuous and intermittent friction tests were carried out. In the intermittent tests, friction was applied periodically: during each cycle, friction was first applied for 2 s at constant sliding speed under constant normal load and then stopped during a latency time of 20 s or 0.5 s. Without friction, the free potential reaches a passive value after immersion in the test solution. When friction force is applied the free potential is shutting down to active values. Under friction the measured current, I can be considered as the sum of two partial currents: one generated by the wear track areas, where the passive film is destroyed and the surface is active; the other one linked to the surface not subjected to friction and that remains in the passive state. A localised corrosion process when subjected to friction in 0.5 M K₂SO₄ was not observed on nano-structured Ni–SiC composite coatings. The mechanical destruction of the passive film occurs in the wear track by friction and subsequent restoration of the film (repassivation) when friction stops. The wear volume loss increases with sliding forces.     

Tribology characteristics of magnesium alloy AZ31B and its composites

In this paper, wear characteristics of magnesium alloy, AZ31B, and its nano-composites, AZ31B/nano-Al₂O_3, processed by the disintegrated melt deposition technique are investigated. The experiments were carried out using a pin-on-disk configuration against a steel disk counterface under different sliding speeds of 1, 3, 5, 7 and 10 m/s for 10 N normal load, and 1, 3 and 5 m/s for 30 N normal load. The worn samples and wear debris were then examined under a field emission scanning electron microscopy equipped with an energy dispersive spectrometer to reveal its wear features. The wear test results show that the wear rates of the composites are gradually reduced over the sliding speed range for both normal loads. The composite wear rates are higher than that of the alloy at low speeds and lower when sliding speed further increased. The coefficient of friction results of both the alloy and composites are in the range of 0.25–0.45 and reaches minimums at 5 m/s under 10 N and 3 m/s under 30 N load. Microstructural characterization results established different dominant mechanisms at different sliding speeds, namely, abrasion, delamination, oxidation, adhesion and thermal softening and melting. An experimental wear map was then constructed.     

Wear behavior of Cu–La2O3 composite with or without electrical current

A new type Cu–La₂O₃ composite was fabricated by internal oxidation method using powder metallurgy. Sliding wear behavior of the Cu–La₂O₃ composites was studied by using a pin-on-disk wear tester under dry sliding conditions with or without electrical current, rubbing against GCr15 type bearing steel disk at a constant sliding speed of 20 m/s. The influence of varying applied load and electrical current was investigated. The worn surfaces were examined using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) to determine the wear mechanisms. The results showed the Cu–La₂O₃ composites had an electrical conductivity of 81.9% IACS (International Annealed Copper Standard, 100% IACS = 58 MS/m) and a hardness of HV105. The wear rate of the Cu–La₂O₃ composite pins increased with the increase in the electrical current at high sliding speed. The main wear mechanisms of the Cu–La₂O₃ composites were found to be adhesive wear, abrasive wear and arc erosion.     

Tribo-oxidation maps for Ti against steel

A fundamental study of wear transition regimes was carried out for a pin-on-disk sliding couple, involving titanium and steel. The sliding speed was varied from 0.38 to 1.5 m s⁻¹ and the normal load from 10 to 50 N. Wear mapping approaches have been undertaken to represent the transitions in wear modes and wear mechanisms regimes, as a function of applied normal loads and sliding speeds and for both pin and disc separately on the basis of experimental results. Dry sliding wear behaviour of steel was characterized by tribo-oxidative wear with high material transfer from the titanium. In contrast, adhesive wear was more prevalent for the titanium and oxidative wear mechanisms led to formation of non-protective films on the surface.     

Tribological behavior of graphite-containing nickel-based composite as function of temperature,load and counterface

Nickel-based graphite-containing composites were prepared by powder metallurgy method. Their mechanical properties at room temperature and friction and wear properties from room temperature to 600 °C were investigated by a pin-on-disk tribometer with alumina, silicon nitride and nickel-based alloy as counterfaces. The effects of graphite addition amount, temperature, load, sliding speed and counterface materials on the tribological properties were discussed. The micro-structure and worn surface morphologies were analyzed by scanning electron microscope (SEM) attached with energy dispersive spectroscopy (EDS). The results show that the composites are mainly consisted of nickel-based solid solution, free graphite and carbide formed during hot pressing. The friction and wear properties of composites are all improved by adding 6–12 wt.% graphite while the anti-bending and tensile strength as well as hardness decrease after adding graphite. The friction coefficients from room temperature to 600 °C decrease with the increase of load, sliding speed while the wear rates increase with the increasing temperature, sliding speed. The lower friction coefficients and wear rates are obtained when the composite rubs against nickel-based alloy containing molybdenum disulfide. Friction coefficients of graphite-containing composites from room temperature to 600 °C are about 0.4 while wear rates are in the magnitude of 10^?5 mm³/(N m). At high temperature, the graphite is not effective in lubrication due to the oxidation and the shield of ‘glaze’ layer formed by compacting back-transferred wear particles. EDS analysis of worn surface shows that the oxides of nickel and molybdenum play the main role of lubrication instead of graphite at the temperature above 400 °C.     

Wear behavior of electroless Ni–P–B4C composite coatings

In this research, the wear of electroless Ni–P and Ni–P–B₄C composite coatings was reviewed. Auto catalytic reduction of Ni in nickel sulfate and sodium hypophosphate bath including suspended B₄C particles with different concentration was used to create composite coatings with 12, 18, 25 and 33 vol.% of B₄C particles. Coatings 35 μm thick were heat treated at 400 °C for one hour in an argon atmosphere and the wear resistance and friction coefficient of heat-treated samples were determined by block-on-ring tests. All wear tests were carried out at 24 °C, 35% moisture, 0.164 m/s sliding speed and about 1000 m sliding distance. Graphs show that an electroless Ni–P–B₄C composite coating with 25 vol.% of B₄C had the best wear resistance against a CK45 steel counterface.     

Plastic deformation of 25CrMo4 steel during wear: Effect of the temperature,the normal force,the sliding velocity and the structural state

This article follows a previous study on friction and wear of 25CrMo4 steel [N. Khanafi-Benghalem, K. Loucif, E. Felder, F. Delamare, Influence de la température sur les mécanismes de frottement et d’usure des aciers X12NiCrMoSi25-20 et 25CrMo4 glissant sur du carbure de tungstène, Matériaux et techniques 93 (2005) 347–362]. The aim of our work is to study in more details the process of plastic deformation and the wear rate of this steel in lubricated sliding against cemented tungsten carbide, process observed in the previous work. The considered parameters are the temperature T (from 20 to 200 °C), the normal force P (from 500 to 1500 N), the steel structure (normalised HV 220 and quenched/tempered HV 480 states) and the sliding velocity v (from 0.05 to 0.3 m/s). We measured the friction coefficient and the sample total volume loss. A displacement sensor follows the volume loss evolution during the test; this follow-up is approximate because of the sample plastic flow which leads to the formation of peripheral burrs. All the tests conditions generate a significant plastic deformation of the sample steel, even in the quenched/tempered state: it produces a marked increase of the surface hardness, the work hardened layer being much finer for the quenched/tempered state (15 μm) than for the normalised state (40 μm at 20 °C). For temperatures T ≤ 100 °C in normalised state, the wear follows the Archard's law with an increasing rate with temperature. For T ≥ 120 °C, the wear rate decreases during the test, the global volume of wear being a decreasing function of T. For the quenched/tempered state, the wear rate decreases with the increase of the normal force, this decrease is less than 30% of the normalised state value. The material heating during the wear tests is well correlated with the friction dissipated power, but remains small, except in extreme cases (v maximum, great friction at high temperatures). These results suggest the existence of two wear mechanisms: abrasion by sample debris and burrs emission by plastic flow. The abrasion is probably the dominating mechanism for the tests carried out at the lowest temperatures. The plastic flow becomes a significant component at the highest temperatures. Using a contact model, we discuss to what extent the influence of the temperature and the strain rate on the steel hardness and ductility could explain the temperature and the sliding velocity effect on wear. Other phenomena are probably present: the influence of the steel microstructure and the lubricant on the size and/or the number of particles responsible for abrasion.     

Tribological behavior of natural fiber reinforced PLA composites

The application spectrum of natural fiber reinforced polymer composites is growing rapidly in various engineering fields. The present study explores the possibilities of reinforcing thermoplastic bio-polymer with locally available inexpensive plant fibers for developing a new tribo-material. Three different types of natural fibers (nettle, grewia optiva and sisal) were incorporated into PLA polymer to develop laminated composites using a hot compression technique. TGA analysis was carried out to investigate the thermal stability of developed composites. Wear and frictional characteristics of developed composites were investigated under dry contact condition at different operating parameters, such as applied load (10–30 N), sliding speed (1–3 m/s) and sliding distance (1000–3000 m). The experimental results indicate that incorporation of natural fiber mats into PLA matrix significantly improves the wear behavior of neat polymer. There was 10–44% reduction in friction coefficient and more than 70% reduction in specific wear rate of developed composites as compared to neat PLA. The worn surface morphology was studied using scanning electron microscope (SEM) to analyze the wear mechanism in different types of developed composites.     

Effects of sliding velocity and normal load on friction and wear characteristics of multi-layered diamond-like carbon (DLC) coating prepared by reactive sputtering

Friction and wear tests were performed to investigate effects of sliding velocity and normal load on tribological characteristics of a multi-layered diamond-like carbon (DLC) coating for machine elements. The DLC coatings which consist of sequentially deposited gradient Cr/CrN, W-doped DLC (a-C:H:W) and DLC (a-C:H) layers were formed on carburized SCM 415 Cr–Mo steel disks using a reactive sputtering system. The tests against AISI 52100 steel balls were performed under various sliding velocities (0.0625, 0.125, 0.25, 0.5, 1 and 2 m/s) and normal loads (6.1, 20.7 and 49.0 N) in ambient air (relative humidity=26±2%, temperature=18±2 °C). Each test was conducted for 20 km sliding distance without lubricating oil. The results show that friction coefficients decrease with the increase in sliding velocity and normal load. Wear rates of both surfaces decrease with the increase in normal load. The increase in sliding velocity leads initially to the increase in wear rates up to the maximum value. Then, they decrease, as the sliding velocity increases above specific value that corresponds to the maximum wear rate. Through surface observation and analysis, it is confirmed that formation of transfer layers and graphitized degree of wear surfaces of DLC coatings mainly affect its tribological characteristics.